Avery Dennison Retail Information Services 7400-433 Wanderer II 433.8 MHz Transceiver User Manual Inst Manual

Download:
Mirror Download [FCC.gov]
Document ID	37481
Application ID	e1x8ALj5QTN/5TywIocHtg==
Document Description	Inst Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.99kB (249830 bits)
Date Submitted	1999-05-14 00:00:00
Date Available	1999-06-28 00:00:00
Creation Date	1999-05-12 14:15:30
Producing Software	Photoshop PDF Plug-in 1.0
Document Lastmod	1999-05-12 14:15:53
Document Title	Inst Manual
Document Creator	Photoshop PDF Plug-in 1.0

OPERATING INSTRUCTIONS
Wanderer II (model 7400) is a radio frequency (RF) device used to
provide a cableless solution to communications between a Symbol®
3800 data collection terminal and a Monarch® 9450” or 9490W
printer. It has two modules; one attaches to each device. The printer
and the terminal can be used up to 3 meters apart.
Following are diagrams of the printers and the terminal with the
Wanderer ll modules attached.
9490 Printer 9450 Printer 3800 Terminal
Installing Wanderer II
System Administrators Only. To install Wanderer II, you attach its
modules to the devices. The printer takes the box-shaped module and
the terminal takes the L-shaped module.
Terminal Installation
To install Wanderer II onto the terminal:
1. Open the door beneath the L—shaped module and insert a Q-volt
battery. It can be Alkaline or rechargeable nickel metal hydride.
TC74000I Revt AA 2/99 ©1999 Monarch Marking Systems, Inc. All rights reserved.
2. Press both sides of the LAshaped module in and snap it into the
optical interface beneath the terminal (at the bottom of the
keyboard).
Printer Installation
To install Wanderer ll onto the printer:
1. Attach Velcro® to the outside of the printer and the box module.
Place the Velcro such that the cable on the box module can
easily reach the printer's serial port.
2. Using the Velcro, attach the box module to the outside of the
printer. Note that because the serial port on the 9490 printer is
at the bottom, you must place the box module so the cable faces
down. On the 9450 printer, place the box module so the cable
faces up.
9490 Printer 9450 Printer
3. Insert the cable from the box module into the printer‘s serial port.
Operating Wanderer ll
Clerks Only. To operate Wanderer ll:
1. Place the data collection terminal and the printer within 6 feet of
each other and turn them on. Wait 2 seconds for the printer to
run a status check.
2. Turn on the Wanderer ll module attached to the printer (green
LED constant). Then, turn on the data collection terminal's
module (green LED constant). The two devices link and the
green LED starts to blink.
3. Use the printer and the terminal as you normally" would.
Troubleshooting \
Following are some suggested courses of action if you have problems.
Problem/Symptom Solution
if the yellow LED continually Change or recharge the Wanderer
blinks twice and pauses, the Il‘s batteryr
battery level is low. .
If the yellow LED blinks five Move the terminal and the printer
times quickly, there was 3 around to find the best relative
transmission error. positions. Be sure there are no
obstacles between them. If it
continues, there is a data error.
Turn the modules off, then back on
to re-link the system and clear any
errors.
Frequently Asked Questions
Following are common questions (and the answers) asked about
Wanderer II.
0: Do i have to use the Wanderer iI modules as selective pairs?
A: No.-The modules link to any other module, but only one at a time.
0: Is there more than one operating frequency?
A: Yes. However, the modules operate at only one frequency at a
time. This frequency is selected when ordering and the factory sets it.
The frequency cannot be changed in the field.
0: Are there any problems using multiple Wanderer lI's in the same
area?
A: No. The modules only respond to messages that are addressed to
each other. This auto addressing happens durir‘ig the linking process.
As stated above, the modules must be set to the same frequency.
0: Can the printer power its Wanderer II module (-P)?
A: Yes, if the printer has +5v available on the serial connector (refer
to the Operator's Handbook for the printer). The correct wiring
harness will allow for this feature. Of course, the internal Wanderer II
module (-P) (which is factory-installed) uses the printer supply voltage
for operation.
0: How many hours will the Wanderer lI‘s batteries run?
A: Alkaline batteries typically run for 120 hours and rechargeable
batteries run for 14 hours. Of course, these numbers vary depending
on the size of transactions and the number of times a message is re-
sent.
0: Can messages be sent to multiple printers at the same time?
A: No. A module can connect to only one module at a time (peer-to-
peer operation).
0: Are there any software configurations and/or commands to change
the operating parameters?
A: No.
FCClozGUs7400-433
This device compiles with part is of the FCC mles. Operation is subject to me following
two conditions: 1) The device may not cause harmful interference, and 2) This device must
accept any interterence received, including interference that may cause undesired
operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 1999:05:12 14:15:53
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 1999:05:12 14:15:30
Page Count                      : 4

EXIF Metadata provided by EXIF.tools