Avery Dennison Retail Information Services QUATECH1 Mobile PrinterModel name - 9485NP User Manual rev GU6 QUATECH1

Avery Dennison Retail Information Services, LLC Mobile PrinterModel name - 9485NP rev GU6 QUATECH1

User Manual_rev (GU6-QUATECH1)

All specifications are subject to change without noticeUSER MANUALTC9485UM Rev. AF 12/14
1Table of Contents 1. Unpacking 2 2. Product overview 3 3. Installation & Usage 4 3-1. Display 4 3-2. Installing the Battery 5 3-3. Removing the Battery 6 3-4. Charging the Battery 7 3-5. Installing Belt Clip 8 3-6. Stock Installation 9 3-7. Peel Mode 10 3-8. Shoulder Strap Installation 11 3-9. Diagnostic Test 12 4. Peripherals Connection 14 4-1. Wireless Communication 14 4-2. Interface Cable Connection 15 5. Printer Cleaning 16 5-1. PrintHead Cleaning 16 5-2. Platen Roller Cleaning 17 6. Pritner Specication 18 6-1. Specication 18 7. CPCL Command Compatibility20 8. ZPL Command Compatibility23RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONTHE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFI-CATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
231. Unpacking StockShoulder StrapSHOULDER STRAP RING Printer Battery Belt Clip RechargerOptionalStandard2. Product overviewCHARGER CONNECTOR COVER OPEN BUTTON FrontBottomCD USB CableQuick ReferenceSerial cable PEELER BODY PEELER WING BATTERY DOOR BELT CLIP CONNECTOR SERIALUSB DISPLAY
45Button Name functionPaper Feed/ Down buttonAdvances the supply. Clears error message. Moves down through menu options.Enter button Selects the highlighted menu option.Up buttonMoves up through menu options.Power buttonTurns the printer on and o. Press to turn power on. Press for three seconds to turn power o. Wakes the printer from sleep mode.3-2. Installing the BatteryNOTENOTE3-1. Display3. Setting Up the ProductRemove the battery door. Insert the battery as shown.1 2Replace the battery door.You must fully charge the battery when you receive the printer. Batteries can be charged in the printer or in an optional external cradle1. The battery status LEDs indicate amount of power remaining. Actual run-time remaining depends on factors such as the contents of output, distance to computer, etc.2. When the battery level is very low, high density printing can result in the printer switching o during printing resulting in possible loss of data.
673-4. Charging the Battery1. Turn o the printer.2. Be sure that the AC plug is correct. If AC plug is wrong, change the plug to the correct one.3. Open the DC jack by pulling on the rubber cover and insert DC jack into the printer.4. Plug the AC plug into an electrical outlet.5. The charge indicator LED (located on the AC charger as shown) shows red or green according to the status.3-3. Removing the Battery3-4-1 The status of lamp in chargingStatus charging charging complete Charging Lamp Red GreenRemove the battery door. Lift out the battery.②①LEDIf there is trouble while charging the battery, the charge indicator LED blinks green. Try unplugging and reconnecting charger, charging should resume. Charging is complete when the LED changes to solid green.NOTE
89Use two hands to close the cover until it clicks into place. Press the feed button.The belt clip is included with the printer but is not required to be used or installed!3-5. Belt clip UsageInsert screw into belt clip.Tighten the screw with driver as shown. 1 2NOTE3-6. Stock Installation1 234Put the stock in so it unrolls from the bottom. Remove the stock core when it is empty. Pull a short length of stock out of the printer.Open the Paper cover by pressing the Open button and set the width of paper guide by turning the knob with nger. Adjust the width of paper guide if needed.
10 113-7. Peel Mode 1 21 2With a roll of stock installed, slide the peeler body towards the back of the printer.Lift the peeler wing and slide the peeler body towards the front of the printer.Press the feed button.Push the peeler body until you see two complete triangles. Press the feed button. Peel Mode Non-Peel Mode Insert the strap into the hook of the printer.Place the end of the strap into the hook of shoulder strap.After pulling out the end of the strap tightly, put it into the clip to be fastened.Optional1323-8. Shoulder Strap Installation
12 133-9. Diagnostic Test 1 23NOTETurn o the printer.The information label prints.Press and hold the feed button and power button.1. For Hex Dump mode, do steps 1-2 then press the feed button.2. After printing ASCII pattern, the diagnostic test is complete.3. If the feed button is not pressed to go to Hex Dump mode, the printer exits diagnostics after three seconds.The sample of self test printoutUpon initial installation or for troubleshooting, you can run the diagnostic test to getinformation about:Firmware version, emulation, codepage, sensor settings, interface settings, etc.If no issues are found with diagnostic test, examine other devices and software. The diagnostic test is working independent of devices and software.● Do not overheat the motor To prevent the motor from overheating, stop the printer for at least 30 seconds after continuously printing 1.5 meters.
14 154. Peripherals ConnectionThis product can communicate with other devices using Bluetooth, WiFi (802.11b/g), or a USB/Serial cable.1. Printer can connect to a PDA or PC for wireless communication.2. Your PC must support Bluetooth or WiFi (802.11b/g) to connect to the printer.4-1. Wireless CommunicationNOTERefer to the System Administrator Guide for more information.4-2. Interface Cable Connection1. Connect the USB or Serial cable to the cable connector on the printer.2. Connect the interface cable into the USB or Serial port of the device (PDA, PC, etc.)NOTEUse only the cables oered by the printer manufacturer.SerialUSB
16 175-1. PrintHead Cleaning5. Printer cleaningIf the interior of the printer is dusty, printing quality can be lowered.In this case, follow the instructions below to clean the printer. NOTE1. Make sure to turn the printer power o prior to cleaning2. The printhead can become very hot during printing; allow the printer approximately 10 minutes to cool before cleaning.3. Do not touch the printhead, it can be damaged by static electricity.4. Take care not to allow the print head to become scratched and /or damaged in any way.1. Use an applicator swab moistened with an isopropyl alcohol to clean the print head and remove any dust.2. Once cleaning is complete, allow the printer to dry then install the stock and close the cover.PrintHead 5-2. Platen Roller Cleaning1.Clean the platen roller with a clean soft cloth moistened with isopropyl alcohol or a cleaning pen.2. Turn the platen roller with your nger to clean the entire surface.Platen Roller
18 19Printing Method Direct ThermalPrinting Speed 80mm/secResolution 203 DPI X 203 DPICharacter ALPHA NUMERIC Character, Extension CharacterBarcode One-Dimensional BarcodesUPCA +2/+5, UPCE +2/+5, EAN8 +2/+5, EAN13 +2/+5,EAN 128, Interleaved 2 of 5, Extended Code 39, Codabar (NW7), Code 128, Code 93, PostNetTwo-Dimensional BarcodesPDF417, MaxiCode, Aztec, QR Code (Quick Response),DatamatrixStacked One-Dimensional BarcodesGS1 Databar (RSS or Composite Code)Emulation CPCL,MPCL,ZPLDriver Window CE 4.2&5.0, Window Mobile 5.0Sensor Black-Mark Upper/Lower, Gap, Cover open, Peeler Detect, Peeler S/W, Media-Width DetectPaper paper type Thermal Paperwidth 56mmthickness 0.06 ~ 0.18 mmExternal Diameter Max. Φ 56mmInternal Diameter 12.5mm±0.5mmReliability TPH 50km Battery Continuous Printing 54minStandby for 11hoursPrinting length: 249.8MCommunications standard Serial(RS-232C), USBOptional Bluetooth Class2, Wireless Lan *802.11b/gPrint tolerances Print feeding 22.7mm ±2.2%(±0.5mm)6-1. Specication6. Printer SpecicationBattery Charger input AC100~240V, 50/60 Hzoutput 8.4V , 800~1200mABattery Battery type Li-ionoutput 7.4V, 18.9whCharging time 3.7 Hrs ChargingSize WXDXH(mm) 104 X 85 X 158WXDXH” 3.9 X 3.3 X 6.2Weight 580g (Bluetooth, Wifi not included)Environmental sealing IP42Temperature operation 5~50℃storage -20~60℃Humidity operation 35 ~ 80%storage 10 ~ 90%
20 21NOTECompatible Partially Compatible Not Compatible○●△xCompatible with only commanders provided by the manufacturer.7. CPCL Command CompatibilityPrinter Commands Compatibility PRINT○FORM○JOURNAL○UNITS○USING COMMENTS○TEXT Compatibility TEXT○FONT-GROUP(FG)○TEXT CONCATENATION○MULTILINE(ML)○COUNT○SETMAG○SCALABLE TEXT Compatibility SCALE-TEXT○SCALABLE CONCATENATION○LINEAR BARCODES Compatibility BARCODE○BARCODE-TEXT○COUNT○Two-Dimensional Bar Codes Compatibility PDF417 (PORTABLE DATA FILE)○MICROPDF-417●MAXICODE○QRCODE○DATAMATRIX●GS1(RSS-14)○AZTEC○GRAPHICS CompatibilityBOX○LINE○INVERSE-LINE○PATTERN○GRAPHICS○PCX○Advanced Commands CompatibilityCONTRAST○TONE○JUSTIFICATION○PAGE-WIDTH○PACE○NO-PACE○WAIT○SPEED○SETSP○ON-FEED○PREFEED○POSTFEED○COUNTRY/CODE PAGE○FORMAT FILES○BEEP○Line Print Mode CompatibilitySETLP○SETLF○Moving With X and Y Coordinates○LMARGIN○
22 23SETBOLD○SETSP○Special ASCII Characters○SETFF○SET-TOF○SETLP-TIMEOUT○ADVANCED UTILITIES CompatibilityVERSION○CHECKSUM○DEL○DIR○DEFINE-FILE○TYPE○BAUD○COUNTRY / CODE-PAGE○TIMEOUT○BEED○ON-LOW-BATTERY○LT○SET-TIME○GET-TIME○SET-DATE○GET-DATE○PRINTING A TIME STAMP○PRINTING A DATE STAMP○PAPER-JAM○PRINTER ESCAPE CompatibilitySET AND READ CODE△STATUS / INFROMATION○USER LABEL COUNT○POWER OFF○8. ZPL Command CompatibilityCommand Compatibility ^A○^B0○^B1○^B2○^B3○^B4○^B5○^B6○^B7○^B8○^B9○^BA○^BB○^BC○^BD○^BE○^BF○^BI○^BJ○^BK○^BL○^BM○^BO○^BP○^BQ○^BR○^BS○^BT○^BU○
24 25Command Compatibility ^BX○^BY○^BZ○^CC ~CC○^CD○^CF○^CI○^CT ~CT○~DF○~DG○^FB○^FC○^FD○^FH○^FN○^FO○^FP○^FR○^FS○^FT○^FV○^FW○^FX○^GB○^GC○^GD○^GE○^GF○^GS○Command Compatibility ^ID○^IL○^IM○^IS○~JR○^JS○~JS○^KL○^LH○^LL○^LR○^LS○^LT○^MC○^MD○^MN○^PM○^PO○^PQ○^PR○~PR○^PW○^SC○^SD○^SF○^SL○^SN○^SO○^ST○
26 27Command Compatibility ~TA○^XA○^XF○^XG○^XZ○^ZZ○

Navigation menu