Axesstel AI113 433MHz W/D Sensor User Manual door sensor

Download:
Mirror Download [FCC.gov]
Document ID	2086728
Application ID	SCmXS7AMAU6uFc9jL1wu3w==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	89.27kB (1115869 bits)
Date Submitted	2013-09-30 00:00:00
Date Available	2013-09-30 00:00:00
Creation Date	2013-08-16 15:03:40
Producing Software	GPL Ghostscript 8.70
Document Lastmod	2013-09-30 11:14:11
Document Title	User manual _door sensor_
Document Creator	ÿþP(Foxit Advanced PDF Editor)
Document Author:	Lindy_Li

User manual of Wireless Door/ window Sensor
Model no.: AI113
The wireless door/window Sensor are widely used in security alarm system and matched with master unit for usage. It is
equipped with a magnet (movement of the magnet triggers an internal sensor in the detector). You can locate the
transmitter module on the frame of the door or window, with the magnet on the moving part of the door or window, It will
send RF signal to the master unit for alarming once be triggered (disconnect).
Specification：
1. Operating voltage：12VDC
2. Static current ≤2µA
3. Operating current ≤30mA
4.Operating frequency：433.92MHZ+/-0.2MHz
5.Transmitting time：<3S
6.Transmitting Field Strength: ≤80.8 dBuV/m
7.Size：31x95×16mm（transmitting partion）
，14x16x99mm (magnet partion)
8.Encode IC：EV1527
9.Modulation Mode: ASK
10.Opearating temp：-20℃ ~ +50℃
11.Battery: 12V23A
12. LED: Trigger transmitting indication
Installation
The wireless door /window Sensor is used to detect whether the door, windows or drawers are opened or moved illegally.
It constitutes by wireless transmitting module, magnet, double faced adhesive tape (accessory).
As the Figure 1 shows
as follow:
Wireless Transmitting Module
Magnet
Double Faced Adhesive Tape
Figure 1
Figure 2
Installation Process:
Step 1: Open the packing and take out the wireless transmitting module and the battery, pull down the slip cover of the
battery jar as Figure 3 shows.
Step 2: Fix the battery (12V 23A) into the jar and close the slip cover as Figure 3 shows .
Step 3: Paste the double faced adhesive tape on the back of the module and the magnet as Figure 4 shows.
The
module and the magnet also have screw holes so that it can be fixed by screw too.
Step 4: Fix the two parts on the door as Figure 5 shows. Please press them hard when paste in order to prevent
dropping caused by the door’s shaking.
Figure 3
Figure 4
Figure 5
Attentions:
Before sticking the module, please clean the area where you plant to stick it.
a. Dust or humidity may cause the module fall off.
b. Parallel the module and the magnet exactly, and the distance should be less than 10mm. Once the two parts have a distance
above 20mm, the indicator light will shine and the module will send alarm signal to the unit base. Make door contact upward
vertically.
c. The magnet should be pasted at the side which is near the indicator light on the module. Make sure the light faces you.
Please stick the magnet on the door and the module on the door case to prevent the module’s fall which causes by the shake of
the door.
d.
When the battery is out of energy, the under-voltage lamp will light, and the battery should be changed in time. Under
normal circumstances, it is suggested to change the battery once 6 mouths.
d.
e.
Please try to shorten the distance between the module and the unit base. It is suggested less than 30 meters.
Try not to make the concrete wall or electrical equipments between the unit base and the module in order to prevent the
signal being cut off.
f.
g.
h.
Keep the module dry.
If the parts are found inverted, it can be pull down and stick again.
After sticking the door contact, please open the door to test the alarm light of the door contact to confirm whether it lights
or not, and to confirm whether the unit base makes local alarm sound (the precondition is to open the local-alarm function),
whether the security number receives alarm message (the precondition is to set the number correctly), whether the security
number receives alarm call (the precondition is to open the voice alarm and set the number correctly).
-------------------------------Note:

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Author                          : Lindy_Li
Create Date                     : 2013:08:16 15:03:40+08:00
ICN App Name                    : Foxit Advanced PDF Editor
ICN App Platform                : Windows
ICN App Version                 : 3.05
Modify Date                     : 2013:09:30 11:14:11
Subject                         : 
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 8717afde-089d-11e3-0000-a84f95a01112
Producer                        : GPL Ghostscript 8.70
Keywords                        : ()
Creator Tool                    : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0001\000.\0000\000.\0002
Document ID                     : 8717afde-089d-11e3-0000-a84f95a01112
Format                          : application/pdf
Title                           : \376\377\000U\000s\000e\000r\000 \000m\000a\000n\000u\000a\000l\000 \000_\000d\000o\000o\000r\000 \000s\000e\000n\000s\000o\000r\000_
Creator                         : \376\377\000L\000i\000n\000d\000y\000_\000L\000i
Description                     : ()
Page Count                      : 2

EXIF Metadata provided by EXIF.tools