Axon Enterprise S00833 Signal PPM User Manual SPPM manual DRAFT 007x

Download:
Mirror Download [FCC.gov]
Document ID	3045485
Application ID	NXNOTVnWSLitQQ60FBQ8Jw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.55kB (131928 bits)
Date Submitted	2016-06-29 00:00:00
Date Available	2016-06-30 00:00:00
Creation Date	2016-06-13 18:51:28
Producing Software	Acrobat Distiller 10.1.16 (Windows)
Document Lastmod	2016-06-13 18:51:28
Document Title	Microsoft Word - SPPM_manual_DRAFT_007.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	tmichaels

TASER Signal Performance Power Magazine User Guide
Before replacing any battery packs, ensure that your CEW’s cartridges have been
removed. Read your CEW’s user manual for the proper unloading procedure.
Introduction
The Signal Performance Power Magazine (SPPM) is a TASER conducted electrical weapon
(CEW) battery pack designed to work with devices that are equipped with Axon Signal
technology.
When an X2 or X26P CEW is equipped with an SPPM, shifting the CEW’s safety switch to the
up (ARMED) position causes the SPPM to broadcast a signal. Upon receipt of this signal, a
compatible device can perform a pre-programmed operation.
The signal starts transmitting approximately three seconds after the safety switch is shifted to
the up (ARMED) position. The signal lasts at least 30 seconds and has a range of up to 30 feet
(9.1 meters).
These are the types of information the SPPM transmits:
Event
Description
ARMED event
The safety switch was shifted to the up (ARMED) position.
ARMED + 10 seconds
The safety switch has been in the up (ARMED) position for 10
seconds.
Trigger event on bay 1
The trigger was pressed with cartridge bay 1 selected (X2 CEW),
or the trigger was pressed (X26P CEW).
Trigger event on bay 2
The trigger was pressed with cartridge bay 2 selected (X2 CEW).
ARC event
An ARC switch was pressed long enough to initiate a spark (X2
CEW).
Broadcasting in SAFE
The safety switch was shifted to the up (ARMED) position and
then shifted to the down (SAFE) position before the 30-second
broadcast ended.
Page 1 of 4
Automatic Shut-Down Option
Your agency can configure your CEW to function with an automatic shut-down feature when the
CEW is equipped with the SPPM. The CEW will function the same way as if it were equipped
with the Automatic shut-down Performance Power Magazine (APPM) battery pack. Read your
CEW’s user manual for more information.
Radio Waves
Changes or modifications to the equipment not expressly approved by the manufacturer could
void the product warranty and the user’s authority to operate the equipment.
Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to
exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S. Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF energy for the general
population. The guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed to assure the safety of all persons,
regardless of age and health. Before a device model is available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the limit established by the government‐
adopted requirement for safe exposure.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult TASER International Customer Service for help.
FCC/IC NOTICE: This device meets the body worn human exposure limits found in OET
Bulletin 65, 2001, and ANSI/ IEEE C95.1, 1992. Proper operation of this equipment according to
the instructions found in this guide will result in exposure substantially below the FCC’s
recommended limits. To comply with the FCC and ANSI C95.1 RF exposure limits, this device
Page 2 of 4
has been tested for compliance with FCC RF Exposure limits in the typical configuration. The
radiated output power of this wireless device is far below the FCC radio frequency exposure
limits.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
RSS 210 Warning Statement: The installer of this equipment must ensure that the antenna is
located or pointed such that it does not emit RF field in excess of Health Canada limits for the
general population; consult Safety Code 6, obtainable from Heath Canada’s Web site www.hc‐
sc.gc.ca/rpb.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
THIS MODEL DEVICE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE
TO RADIO WAVES.
Section 8.4 of RSS-GEN
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is
subject to the following two conditions: 1) this device may not cause interference, and 2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Cet appareil est conforme aux normes d’exemption de licence RSS d’Industrie Canada. Son
utilisation est soumise aux conditions suivantes : 1) cet appareil ne doit pas causer de
brouillage, et 2) doit accepter tout brouillage, y compris le brouillage pouvant entraîner un
fonctionnement indésirable.
Section 8.3 of RSS-GEN
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio ne peut
fonctionner qu’au moyen d’une antenne d’un seul type et d’un gain maximal (ou inférieur)
approuvé pour l’émetteur par Industrie CanChapter 7: Troubleshooting 18 ada. Dans le but de
réduire les risques de brouillage radioélectrique pour les autres utilisateurs, il faut choisir le type
d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas celle requise pour établir une communication satisfaisante.
Page 3 of 4
THIS MODEL DEVICE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE
TO RADIO WAVES.
Axon, Axon Signal, X2, and X26P are trademarks of TASER International, Inc., some of which are registered in the US and other
countries. For more information, visit www.taser.com/legal. All rights reserved. © 2016 TASER International, Inc.
Page 4 of 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : tmichaels
Create Date                     : 2016:06:13 18:51:28-07:00
Modify Date                     : 2016:06:13 18:51:28-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.1.16 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - SPPM_manual_DRAFT_007.docx
Creator                         : tmichaels
Document ID                     : uuid:c3f0ece2-4685-4152-8d36-1c5b157a8e9b
Instance ID                     : uuid:a91ec047-4364-4b9b-ba4d-565b0a309c9e
Page Count                      : 4

EXIF Metadata provided by EXIF.tools