Azlan Logistics AV-1800 Digital Amplifier User Manual
Azlan Logistics Limited Digital Amplifier
User Manual
Digital Amplifier AV-1800 Snapshot > 2 x 50w RMS (at 8 ohms) low impedance digital power amplifier > 3 x Stereo inputs / 1 x Stereo Pre-Output / 1 x Balanced Mic input with Phantom Power > Bluetooth Input > IR remote included, RS-232 control Details The improved AV-1800 is compact, and has a simple interface with just two dials which are turned to adjust and pushed to switch. It has a selection of inputs – including Bluetooth and a microphone input, making it suitable for meeting rooms, small auditoriums, lecture theatres, school halls, and small churches. Bluetooth The amplifier can automatically switch to the Bluetooth source when it is paired. Bluetooth can be renamed and the pin changed by connecting to a PC (see software link below). Microphone Input It uses a professional XLR connector and the input is “balanced” to eliminate electro-magnetic noise induced on long cables. The microphone input has “Phantom Power” – a voltage which is required by condenser-type microphones such as lectern microphones. RS-232 It can be controlled by a control device such as Techconnect Control via IR or RS-232. It also comes with an IR remote control gives the user bass and treble adjustment and direct input selection. D-Class An efficient Digital-class amplifier chip dramatically reduces power consumption especially at rest. 3 x Stereo Inputs Three stereo inputs accept input from a variety of sources such as computers (via the headphone jack), tablets or phones. 2 of the inputs are via 2-phono (RCA) connectors on the rear panel. Input 3 is via a 3.5mm Minijack connector, and is duplicated on the front and rear panels for easy access. Line Output A line-level pre-output on the rear panel bypasses the internal amplifier. It would connect to a larger amplifier or powered loudspeakers. It is post-mix, which means any volume adjustment made on the front panel affects the output level. Auto-Standby If the amplifier senses no input it will automatically go into standby mode. When it senses input it will reactivate. Auto-standby can be disabled. Mounting Options Optional mounting hardware is included to allow cable-tying either to a projector ceiling pole, or into a rack. Manual Bluetooth Management Software Specifications AMPLIFIER DIMENSIONS: 236 x 215 x 64mm / 9.05″ x 8.46″ x 2.56″ (wide x deep x tall) not including dials and connectors CARTON DIMENSIONS: 415 x 230 x 80 mm / 16.34″ x 9.06″ x 3.15″ AMPLIFIER WEIGHT: 2.0 kg / 4.4 lb PACKAGED WEIGHT: 2.4 kg / 5.3 lb COLOUR: White INPUTS 3 x Stereo inputs via 2-phono (RCA) connectors / 1 x 3.5mm (1/4″) 1 x Bluetooth input 1 x Microphone inputs via balanced XLR OUTPUTS 1 x Stereo Line-level output via phono connectors (post mix) TECHNICAL DETAILS 2 x 50w @ 8 ohms Total Harmonic Distortion <1% Frequency response (line in): 20Hz~20kHz Signal to noise ratio (line in): 75dB Rating input level/Impedance: line in 800~900mV/47kohms Operating temperature range: 0 to +40°C (32 to +104 °F) Power consumption (rating condition): <=125W Phantom Power Disable: via internal jumper Phantom Power: 21V ACCESSORIES INCLUDED 1 x 2-phono to 2-phono cable 2m long 1 x 3.5mm to 3.5mm minijack cable 2m long 2 x Unshielded Speaker Cable 5m long 1 x UK C7 figure-8 power cable 1.8 m long 1 x EU C7 figure-8 power cable 1.8 m long 1 x AU C7 figure-8 power cable 1.8 m long 1 x US C7 figure-8 power cable 1.8 m long 1 x Remote Control (Battery included: CR2025 3V Li-Mn) 1 x Rack ears 1 x Ceiling pole and wall brackets POWER SUPPLY: 100~240V Internal Power Supply WARRANTY: 3-year return to base COMPLIANCES: RoHS, WEEE, CE/EMC, CE/LVD, C-TICK, FCC ORDER PART CODE: AV-1800 [SAP: 4262711] or AV-1800+CS-1800 bundle [SAP:4363207] or AV-1800+SP-1800B bundle [SAP:4363208] or AV-1800+SP-1800 bundle [SAP:4363209] SPARE IR REMOTE CONTROL: AV-1800 RC [SAP: 4360133] FCC STATEMENT : minijack This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving an tenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 4 Author : Administrator Comments : Company : Create Date : 2017:11:10 11:45:15+03:45 Creator : WPS Office Modify Date : 2017:11:10 11:45:15+03:45 Producer : Source Modified : D:20171110114515+03'45' Subject : Title : Trapped : falseEXIF Metadata provided by EXIF.tools