AzureWave Technologies BT046 Bluetooth Module User Manual Usre s manual rev

Download:
Mirror Download [FCC.gov]
Document ID	1248531
Application ID	kHSwTcQwm17tII7Lh1hOqA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.34kB (916739 bits)
Date Submitted	2010-03-04 00:00:00
Date Available	2010-03-04 00:00:00
Creation Date	2010-03-04 09:17:18
Producing Software	GPL Ghostscript 8.61
Document Lastmod	2010-03-04 09:41:32
Document Title	Usre's manual_rev
Document Creator	PDFCreator Version 0.9.5
Document Author:	Teresa

AzureWave / AW-BT046
Bluetooth Software
User Manual
Install the Bluetooth Driver…………………………………………..2
Connect to other Bluetooth Enabled Devices……………………..7
Uninstall the Bluetooth Driver……………………………………….11
Install the Bluetooth Driver
Step1：Double click WIDCOMM Bluetooth Software 6.x.x.xx
Step2 ：Choose 『I accept the terms in the license agreement』
Step3：Double click 『Next』
Step4：Choose『Install』
Step5：Install finish
Connect to other Bluetooth Enable
Device
Step1: Search new Bluetooth devices.
Step2 : Double click 『Next』
Step3 : Double click 『Next』
Step4:
10
Uninstalling the Bluetooth Driver
Step1:
11
Step2:
12
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. To maintain compliance with FCC RF exposure compliance requirements,
please follow operation instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
13
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna,
As long as 1 condition above is met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains FCC
ID: TLZ-BT046”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
14


Canadian Regulatory Wireless Notice
Canadian Regulatory Wireless Notice
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to
the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause
undesired operation of the device
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instructions for
satisfying RF exposure compliance. To maintain compliance with Canada RF exposure
compliance requirements, please follow operation instruction as documented in this
manual.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna,
As long as 1 condition above is met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the Canada ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate Canada authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains IC:
6100A-AWBT046”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
15
For Taiwan警語
警語
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線
電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之
干擾。
Note:
1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤
2. 系統廠商應於平台上標示「本產品內含射頻模組:
16
XXXyyyLPDzzzz-x」字樣

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
XMP Toolkit                     : 3.1-701
About                           : 59df19af-2987-11df-0000-38a528d5a514
Producer                        : GPL Ghostscript 8.61
Keywords                        : 
Modify Date                     : 2010:03:04 09:41:32+08:00
Create Date                     : 2010:03:04 09:17:18+08:00
Creator Tool                    : PDFCreator Version 0.9.5
Metadata Date                   : 2010:03:04 09:41:32+08:00
Document ID                     : 59df19af-2987-11df-0000-38a528d5a514
Instance ID                     : uuid:6d3644ac-7073-441b-8502-eca10118bea6
Format                          : application/pdf
Title                           : Usre's manual_rev
Creator                         : Teresa
Description                     : 
Page Count                      : 17
Subject                         : 
Author                          : Teresa

EXIF Metadata provided by EXIF.tools