AzureWave Technologies NH930 IEEE 802.11 a/b/g/n Wireless LAN, Bluetooth and FM Combo Half Mini Card User Manual

AzureWave Technologies, Inc. IEEE 802.11 a/b/g/n Wireless LAN, Bluetooth and FM Combo Half Mini Card

User Manual

AW-NH930 IEEE 802.11 a/b/g/n Wireless LAN, Bluetooth and FM Rx Combo Half Mini Card Datasheet Version 0.8 -1-
Document release Date Modification Initials ApprovedVersion 0.1 2009/10/23 Initial Version N.C. Chen CE Huang Version 0.2 2009/10/26 Modify pin definition N.C. Chen CE Huang Version 0.3 2009/11/05 Modify pin definition VDDIO supply pin 24 change to pin 28 N.C. Chen CE Huang Version 0.4 2009/11/06 Modify pin definition Swap PCM/UART pins N.C. Chen CE Huang Version 0.5 2010/4/21 Modify block diagram and mechanical information N.C. Chen CE Huang Version 0.6 2010/6/02 Modify pin 44 & 46 description Add page25 Antenna Information Update 1-3 Specifications Table N.C. Chen CE Huang Version 0.7 2010/12/14 Update Operating Temperature Add 2-7. Power-on sequence N.C. Chen CE Huang Version 0.8 2010/12/24 Update 5.Antenna port information Output power 11a : 11 dBm (± 2dBm) N.C. Chen CE Huang -2-
Table of Contents 1. General Description 1-1.Product Overview and Functional Description 1-2. Key Features 1-3. Specifications Table 2. Electrical Characteristic 2-1. Absolute Maximum Ratings 2-2. Recommended Operating Conditions 2-3. DC Characteristics for Host I/O 2-4. BT/FM Host Interface 2-5. SDIO Timing 2-6. LPO Clock (RTC_CLK) 2-7. Power-On sequence 3. Pin Definition 3-1. Pin Description 3-2. Pin Description comparison with PCI-Express specification 4. Mechanical Information 5. Antenna port Information -3-
1. General Description 1-1. Product Overview and Functional Description AzureWave Technologies, Inc. introduces the first IEEE 802.11a/b/g/n WLAN, Bluetooth and FM combo module - AW-NH930. The module is targeted to mobile devices including, Digital Still Cameras (DSCs), Portable Media Players (PMPs), and Gaming Devices, mobile phones which need small footprint package, low power consumption, multiple OS support. By using AW-NH930, the customers can easily enable the Wi-Fi, BT and FM embedded applications with the benefits of high design flexibility, short development cycle, and quick time-to-market. Compliance with the IEEE 802.11a/b/g/n standard, the AW-NH930 uses DSSS, OFDM, DBPSK, DQPSK, CCK and QAM baseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize the system power requirements by using AW-NH930. In addition to the support of WPA/WPA2 (personal) and WEP encryption, the AW-NH930 also supports the IEEE 802.11i security standard through AES and TKIP acceleration hardware for faster data encryption. The AW-NH930 is also Cisco Compatible Extension (CCX) certified. For the video, voice and multimedia applications the AW-NH930 support 802.11e Quality of Service (QoS). For Bluetooth operation, the AW-NH930 is Bluetooth 2.1+Enhanced Data Rate (EDR) compliant. The AW-NH930 supports extended Synchronous Connections (eSCO), for enhanced voice quality by allowing for retransmission of dropped packets, and Adaptive Frequency Hopping (AFH) for reducing radio frequency interference. It provides easier to connect devices, lower power consumption and improved security. For FM receiver/transmitter, the AW-NH930 is 76-MHz to 108-MHz FM bands supported and supports the European Radio Data Systems (RDS) and the North American Radio Broadcast Data System (RBDS) modulations. The AW-NH930 supports standard interface SDIO v1.2 (4-bit and 1-bit) for WLAN, High-speed UART interface for BT/FM host controller interface, and PCM for BT audio data. The demodulated FM audio signal is available as line-level analog stereo output. AW-NH930 is suitable for multiple mobile processors for different applications. With the combo functions and the good performance, the AW-NH930 is the best solution for the consumer electronics and the laptops. -4-
1-2. Key Features General Integrates Broadcom solutions of BCM4329 WiFi/BT/FM SoC SDIO interfaces support for WLAN ECI—enhanced coexistence support, ability to coordinate BT SCO transmissions around WLAN receives High speed UART and PCM for Bluetooth FM subsystem control through Bluetooth HCI interface Flexible Power Supply(2.3V~5.5V) Multiple power saving modes for low power consumption Lead-free /Halogen Free Design WLAN Dual- band 2.4 GHz/5GHz 802.11 a/b/g/n Supports antenna diversity Supports IEEE 802.11d, e, h,i, j,r,k,w Security–WEP, WPA/WPA2 (personal), AES (HW), TKIP (HW), CKIP (SW). WMM/WMM-PS/WMM-SA Proprietary protocol –CCXv2/CCXv3/CCXv4/CCXv5, WFAEC Integrated CPU with on-chip memory for a complete WLAN subsystem minimizing the need to wake up the applications processor Bluetooth Fully supports Bluetooth Core Specification version 2.1 + EDR features Support BT3.0+HS Maximum UART baud rates up to 4 Mbps Multipoint operation with up to seven active slaves -5-
FM 76-MHz to 108-MHz FM bands supported (US, Europe, and Japan) RDS and RBDS demodulator and decoder with filter and buffering functions Auto search and tuning modes FM line-level analog stereo output available Block Diagram A simplified block diagram of the AW-NH930 module is depicted in the figure below. VBAT 2.3~5.5V for internal PMU ANT 1 BCM4329 SP3T BPF 2.4 GHz WLAN Rx/BT Rx 2.4 GHz BT Tx XTAL FM Rx AntennaFM RxRTC_Clk32.768KHz2.4 GHz WLAN TxUART for BT/FM SDIO for WLAN PCM for BT Analog Line-out/in for FM 5 GHz WLAN Tx5 GHz WLAN Rx SWLNADiplexer SW ANT 2-6-
1-3. Specifications Table *Specifications are subject to change without notice Model Name AW-NH930 Product Description Wireless LAN &Bluetooth & FM WLAN Standard IEEE 802.11a/b/g/n, Wi-Fi compliant Bluetooth Standard Bluetooth 2.1+Enhanced Data Rate (EDR) / BT3.0+HS Host Interface SDIO for WLAN UART for Bluetooth and FM Audio Interface Digital PCM for Bluetooth. Analog line level i/o for FM. Dimension 26.6 mm X 29.8 mm x 3.2 mm Package Half mini card package Operating Conditions Voltage Input supply for internal PMU: 2.3 ~ 5.5V Input supply for host I/O : 1.8 to 3.3V Temperature Operating: 0 ~ 70oC ; Storage: -40 ~ 85oC Relative Humidity < 60 % ( storage) <85% (operation) Electrical Specifications Frequency Range 2.4 GHz / 5GHz Band 76 MHz to 108 MHz FM bands Number of Channels 802.11b: USA, Canada and Taiwan – 11 Most European Countries – 13 Japan – 14 802.11g: USA and Canada – 11 Most European Countries – 13 802.11a: USA – 19(24 optional) Most European Countries –19 Japan – 4 Modulation *DSSS, OFDM, DBPSK, DQPSK, CCK, 16-QAM, 64-QAM for WLAN *GFSK (1Mbps), Π/4 DQPSK (2Mbps) and 8DPSK (3Mbps) for Bluetooth -7-
Output Power WLAN: 11b: 16 dBm (± 2dBm) 11g: 15 dBm (± 2dBm) 11n: 13 dBm (± 2dBm) 11a: 11 dBm (± 2dBm) Bluetooth: 6.5 dBm (Typ.) Receive Sensitivity WLAN: 11b (11Mbps): -84 dBm 11g (54Mbps): -70 dBm 11n (HT20 MCS7): -66 dBm 11a (54Mbps): -70 dBm 11a (HT20 MCS7): -68 dBm Bluetooth: GFSK: -83 dBm π/4-DQPSK: -86 dBm 8-DPSK: -81 dBm FM: 0 dBuV (Audio) Data Rates WLAN 802.11b: 1, 2, 5.5, 11Mbps 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n:MCS 0~7 HT20 Bluetooth Bluetooth 2.1+EDR data rates of 1,2, and 3Mbps Power Consumption Not specified. Operating Range Open Space: ~300m ; Indoor: ~100m for WLAN Minimum 10 m indoor for Bluetooth (The transmission speed may vary according to the environment) Security  WPA™- and WPA2™- (Personal) support for powerful encryption and authentication  AES and TKIP acceleration hardware for faster data encryption and 802.11i compatibility  Cisco® Compatible Extension- (CCX, CCX 2.0, CCX 3.0, CCX 4.0,CCX5.0) certified  SecureEasySetup™ for simple Wi-Fi® setup and WPA2/WPA security configuration  Wi-Fi Protected Setup (WPS)  WEP  CKIP(Software) Operating System Compatibility TBD -8-
2. Electrical Characteristics 2-1. Absolute Maximum Ratings Symbol Parameter Min Max Units VDD_CORE Power supply for Core Voltage Voltage -0.5 1.32 V VDDIO_SD Host I/O power supply for WL -0.5 4.1 V VDDIO I/O power supply for BT/FM/GPIO -0.5 4.1 V VBAT_IN Power supply for Internal Regulators -0.5 6.5 V VDD_RADIO_PLL_IN Power supply for Noise Sensitive Block (AFE,PLL…) -0.5 1.32 V 2-2. Recommended Operating Conditions Symbol Parameter Type Min Typ Max UnitsVDD1P4_LDO_IN Power supply for Internal CLDO/LDO1 Input 1.35 1.4 2 V VDD_RADIO_PLL_IN Power supply for Noise Sensitive Block (AFE,PLL…) Input 1.1 1.225 1.35 V VDD1P2_LDO1_OUT Power supply from Internal LDO1 Output 1.1 1.225 1.35 V VDD1P4_LNLDO2_IN Power supply for Internal LDO2 Input 1.35 1.4 2 V VDD_BT_PA Power supply for BT PA Input 3.3 V VDD_WL_PA Power supply for WL PA G Mode Input 3.3 V VDD_WL_PA_A_MODE Power supply for WL PA A Mode Input 3.3 V VBAT_IN Power supply for Internal Regulators Input 2.3 5.5 V VDD_CORE Power supply for Core Voltage Input 1.1 1.225 1.35 V VDD1P2_CLDO_OUT Internal LDO for VDD_CORE Output 1.1 1.225 1.35 V VDDIO_SD Host I/O power supply for WL Input 1.62 1.8/3.3 3.63 V VDDIO I/O power supply for BT/FM/GPIO Input 1.62 1.8/3.3 3.63 V VDDIO_RF I/O power supply for RF front-end Input 3.3 V SR_PA_OUT Power Supply from Internal Buck/Boost Regulator Output 3.3 V VDD1P2_LNLDO2_OUT Power supply from Internal Output 1.1 1.225 1.35 V VDD_FM Power Supply for FM Input 1.1 1.225 1.35 V -9-
2-3. DC Characteristics for Host I/O Symbol Parameter Condition Min Typ Max Units VIL Input low voltage (VDDIO VDDIO_SD) 1.8V Logic 0.6 V VIH Input high voltage (VDDIO VDDIO_SD) 1.8V Logic 1.1 V VOL(~100uA Load) Output low voltage (VDDIO VDDIO_SD) 1.8V Logic 0.2 V VOH(~100uA Load) Output high voltage (VDDIO V)1.8V Logic VIO - 0.2V V VIL Input low voltage (VDDIO VDDIO_SD) 3.3V Logic 0.8 V VIH Input high voltage (VDDIO VDDIO_SD) 3.3V Logic 2.0 V VOL(~100uA Load) Output low voltage (VDDIO VDDIO_SD) 3.3V Logic 0.2 V VOH(~100uA Load) Output high voltage (VDDIO 3.3V Logic VIO - 0.2V V 2-4. BT/FM Host Interface The AW-NH930 is the optimal solution for any voice or data application that requires the Bluetooth SIG standard Host Controller Interface (HCI) using a high-speed UART. The FM subsystem and the Bluetooth subsystem share the same high-speed UART 2-4-1. UART Interface The UART physical interface is a standard, 4-wire interface (RX, TX, RTS, CTS ) with adjustable baud rates from 9600 bps to 4.0 Mbps. The interface defaults to a baud rate of 115.2 Kbps coming out of reset. The desired high-speed baud rate may be selected via a vendor-specific UART HCI command. The AW-NH930 has a 480-byte receive FIFO and a 480-byte transmits FIFO to support EDR. The interface supports the Bluetooth 2.1 UART HCI (H4) specification. The default baud rate for H4 is 115.2 k baud. In order to support both high and low baud rates efficiently, the UART clock can be selected as either 24 or 48 MHz. Generally, the higher speed clock is needed for baud rates over 3 M baud, however a lower speed clock may be used to achieve a more accurate baud rate under 3 M baud. The legacy method of programming the high-speed baud rate of the AW-NH930 UART using DHBR and DLBR values is also supported for backward compatibility with previous-generation Bluetooth devices. Normally, the UART baud rate is set by a configuration record downloaded after reset, or by automatic baud rate detection and the host does not need to adjust the baud rate. Support for changing the baud rate during normal HCI UART operation is included through a vendor-specific command that allows the host to adjust the contents of the baud rate registers. The AW-NH930 UART operates correctly with the host UART, provided the combined baud rate error of the two devices is within ±5% -10-
2-4-1.1. UART Interface Signals Pin No Pin Name Description Type10 BT_UART_TXD Bluetooth UART Serial Output Serial data output for the HCI UART Interface O 12 BT_UART_RXD Bluetooth UART Series Input Serial data input for the HCI UART Interface I 14 BT_UART_RTS_N Bluetooth UART Request to Send. Active-low request to send signal for the HCI UART interface O 8 BT_UART_CTS_N Bluetooth UART Clear to Send Active-low clear to send signal for the HCI UART interface. I 2-4-1.2. UART Timing Values are specified in the recommended operating conditions unless otherwise specified. Symbol Description Min Typ Max Units 1 Delay time, BT_UART_CTS_N low to UART_TXD valid 24 Baudout cycles2 Setup time, BT_UART_CTS_N high before midpoint of stop bit 10 ns 3 Delay time, midpoint of stop bit to BT_UART_RTS_N high 2 Baudout cycles-11-
2-4-2. PCM Interface The PCM Interface on the AW-NH930 can connect to linear PCM Codec devices in master or slave mode. In master mode, the AW-NH930 generates the BT_PCM_CLK and BT_PCM_SYNC signals, and in slave mode, these signals are provided by another master on the PCM interface and are inputs to the AW-NH930. The AW-NH930 supports up to three SCO or eSCO channels through the PCM Interface and each channel can be independently mapped to any of the available slots in a frame. The configuration of the PCM interface may be adjusted by the host through the use of Vendor Specific HCI Commands. 2-4-2.1. PCM Interface Signals Pin No Pin Name Description Type17 BT_PCM_SYNC PCM sync signal, can be master (output) or slave (input) I/O 5 BT_PCM_OUT PCM data output O 3 BT_PCM_IN PCM data input I 19 BT_PCM_CLK PCM clock, can be master (output) or slave (input) I/O 2-4-2.2. PCM Interface Timing Short Frame Sync, Master Mode -12-
Values are specified in the recommended operating conditions unless otherwise specified. Symbol Description Min Typ Max Units1 PCM bit clock frequency 128 2048 kHz 2 PCM bit clock high time 128 ns 3 PCM bit clock low time 209 ns 4 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC high 50 ns 5 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC low 50 ns 6 Delay from BT_PCM_CLK rising edge to data valid on BT_PCM_OUT 50 ns 7 Setup time for BT_PCM_IN before BT_PCM_CLK falling edge 50 ns 8 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 ns 9 Delay from falling edge of BT_PCM_CLK during last bit period to BT_PCM_OUT becoming high impedance 50 ns Short Frame Sync, Slave Mode -13-
Values are specified in the recommended operating conditions unless otherwise specified. Symbol Description Min Typ Max Units1 PCM bit clock frequency 128 2048 kHz 2 PCM bit clock high time 209 ns 3 PCM bit clock low time 209 ns 4 Setup time for BT_PCM_SYNC before falling edge of BT_PCM_BCLK 50 ns 5 Hold time for BT_PCM_SYNC after falling edge of BT_PCM_CLK 10 ns 6 Hold time of BT_PCM_OUT after BT_PCM_CLK falling edge 175 ns 7 Setup time for BT_PCM_IN before BT_PCM_CLK falling edge 50 ns 8 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 ns 9 Delay from falling edge of BT_PCM_CLK during last bit period to BT_PCM_OUT becoming high impedance 100 ns Long Frame Sync, Master Mode -14-
Values are specified in the recommended operating conditions unless otherwise specified. Symbol Description Min Typ Max Units1 PCM bit clock frequency 128 2048 kHz 2 PCM bit clock high time 209 ns 3 PCM bit clock low time 209 ns 4 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC high during first bit time 50 ns 5 Delay from BT_PCM_CLK rising edge to BT_PCM_SYNC low during third bit time 50 ns 6 Delay from BT_PCM_CLK rising edge to data valid on BT_PCM_OUT 50 ns 7 Setup time for BT_PCM_IN before BT_PCM_CLK falling edge 50 ns 8 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 ns 9 Delay from falling edge of BT_PCM_CLK during last bit period to BT_PCM_OUT becoming high impedance 50 ns Long Frame Sync, Slave Mode -15-
Values are specified in the recommended operating conditions unless otherwise specified. Symbol Description Min Typ Max Units1 PCM bit clock frequency 128 2048 kHz 2 PCM bit clock high time 209 ns 3 PCM bit clock low time 209 ns 4 Setup time for BT_PCM_SYNC before falling edge of BT_PCM_CLK during first bit time 50 ns 5 Hold time for BT_PCM_SYNC after falling edge of BT_PCM_CLK during second bit period. (BT_PCM_SYNC may go low any time from second bit period to last bit period) 10 ns 6 Delay from rising edge of BT_PCM_CLK or BT_PCM_SYNC (whichever is later) to data valid for first bit on BT_PCM_OUT 50 ns 7 Hold time of BT_PCM_OUT after BT_PCM_CLK falling edge 175 ns 8 Setup time for BT_PCM_IN before BT_PCM_CLK falling edge 50 ns 9 Hold time for BT_PCM_IN after BT_PCM_CLK falling edge 10 10 Delay from falling edge of BT_PCM_CLK or BT_PCM_SYNC (whichever is later) during last bit in slot to BT_PCM_OUT becoming high impedance 100 ns 2-5. SDIO Timing The AW-NH930 has an internal power-on reset (POR) circuit. The device will be held in reset for a maximum of 110 ms after VDDC and VDDIO have both passed the 0.6V threshold. Wait at least 110 ms after VDD_CORE and VDDIO are available before initiating SDIO accesses. The external reset signals are logically ORed with this POR. So if either the internal POR or one of the external resets is asserted, the device will be in reset. -16-
-17- SDIO Bus Timing(1) (Default Mode)
-18- SDIO Bus Timing (High-Speed Mode)
2-6. LPO Clock (RTC_CLK) 2-7. Power-On Sequence The AW-NH931 has four signals that allow the host to control power consumption by enabling or disabling the Bluetooth, WLAN and internal regulator blocks. These signals are described below. Additionally, diagrams are provided to indicate proper sequencing of the signals for carious operating states. The timing value indicated are minimum required values: longer delays are also acceptable. Note: The WL_SHUTDOWN_N and BT_SHUTDOWN_N are ORed in the AW-NH931. The diagrams show both signals going high at the same time (as would be the case if both SHUTDOWN signals were controlled by a single host GPIO). If two independent host GPIOs are used (on for WL_SHUTDOWN_N and one for BT_SHUTDOWN_N), then only one of two signals needs to be high to enable the AW-NH931 regulators. Also note that the reset requirements for the Bluetooth core are also applicable for the FM core. In other words, if FM is to be used, then the Bluetooth core must be enabled. WL_SHUTDOWN_N: Used by the PMU (along with BT_SHUTDOWN_N) to decide whether to power down the internal AW-NH931 regulators. If both the BT_SHUTDOWN_N and WL_SHUTDOWN_N pins are low, the regulators will be disabled. BT_SHUTDOWN_N: Used by the PMU (along with WL_SHUTDOWN_N) to decide whether to power down the internal AW-NH931 regulators. If both the BT_SHUTDOWN_N and WL_SHUTDOWN_N pins are low, the regulators will be disabled. -19-
-20-WL_RST_N: Low asserting Reset for WLAN Core. This pin must be driven high or low ( not left floating ). BT_RST_N: Low asserting Reset for Bluetooth Core. This pin must be driven high or low (not left floating). 2-7.1 Power on sequence for WLAN=ON and Bluetooth=ON 2-7.2 Power on sequence for WLAN=OFF and Bluetooth=OFF
-21-2-7.3 Power on sequence for WLAN=ON and Bluetooth=OFF 2-7.4 Power on sequence for WLAN=OFF and Bluetooth=ON
3. Pin Definition 3-1. Pin Description Pin No Pin Name Description Type1 WL_HOST_WAKE Host wake up. Signal from the AW-NH930 to the host indicating that theWLAN device requires attention. ‧ Asserted: Host device must wake-up or remain awake. ‧ Deasserted: Host device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. O 2 VBAT3V3_IN Power supply for Internal regulators I 3 BT_PCM_IN PCM data input (Pin definition for module side) I 4 GND Ground 5 BT_PCM_OUT PCM data output (Pin definition for module side) O 6 NC No Connect 7 BT_HOST_WAKE Host wake up. Signal from the AW-NH930 to the host indicating that the Bluetooth device requires attention. ‧ Asserted: Host device must wake-up or remain awake. ‧ Deasserted: Host device may sleep when sleep criteria are met. The polarity of this signal is software configurable and can be asserted high or low. O 8 BT_UART_CTS_N Bluetooth UART Clear to Send Active-low clear to send signal for the HCI UART interface. (Pin definition for module side) I 9 GND Ground 10 BT_UART_TXD Bluetooth UART Serial Output Serial data output for the HCI UART Interface (Pin definition for module side) O 11 FM_AUDIO_L FM Rx analog audio output channel Left (DC Block Capacitor Required) O 12 BT_UART_RXD Bluetooth UART Series Input Serial data input for the HCI UART Interface (Pin definition for module side) I 13 FM_AUDIO_R FM Rx analog audio output channel Reft (DC Block Capacitor Required) O 14 BT_UART_RTS_N Bluetooth UART Request to Send. Active-low request to send signal for the HCI UART interface (Pin definition for module side) O 15 GND Ground 16 BT_WAKE Bluetooth device wake-up: Signal from the host to the AW-NH930 indicating that the host requires attention. ‧ Asserted: Bluetooth device must wake-up or remain awake. ‧ Deasserted: Bluetooth device may sleep when sleep criteria are met.The polarity of this signal is software configurable and can be asserted high or low. I 17 BT_PCM_SYNC PCM sync signal, can be master (output) or slave (input) (Pin definition for module side) 18 GND Ground 19 BT_PCM_CLK PCM clock, can be master (output) or slave (input) (Pin definition for module side) I/O -22-
Pin No Pin Name Description Type20 BT_RST_N Low Asserting Reset for Bluetooth Core. I 21 GND Ground 22 WL_RST_N Low asserting reset for WLAN. I 23 NC No Connect 24 VBAT3V3_IN Power supply for Internal regulators I 25 NC No Connect 26 GND Ground 27 GND Ground 28 VDDIO Digital I/O power supply for WL/BT/FM (1.8V~3.3V) I 29 GND Ground 30 NC No Connect 31 NC No Connect 32 NC No Connect 33 NC No Connect 34 GND Ground 35 GND Ground 36 NC No Connect 37 SDIO_DATA2_SPI_NC SDIO 4-bit Mode: Data line 2 or Read Wait SDIO 1-bit Mode: Read Wait This pin has an internal weak pull-up resistor. The resistor is enabled by default but can be disabled by software. The value of the pull-up depends on the VDDIO_SD supply voltage. For 1.8V, the resistance range is 30–82 k Ohms. For 2.6V, it ranges from 21–41 k Ohms. For 3.3V, it ranges from 15–35 k Ohms . I/O 38 NC No Connect 39 SDIO_CLK_SPI_CLK SDIO Clock (Pin definition for module side) I 40 GND Ground 41 SDIO_DATA3_SPI_CS SDIO 4-bit Mode: Data line 3 SDIO 1-bit Mode: Not used This pin has an internal weak pull-up resistor. The resistor is enabled by default but can be disabled by software. The value of the pull-up depends on the VDDIO_SD supply voltage. For 1.8V, the resistance range is 30–82 k Ohms. For 2.6V, it ranges from 21–41 k Ohms. For 3.3V, it ranges from 15–35 k ohms I/O 42 WL_SHUTDOWN_N Low asserting reset for WLAN core. I 43 SDIO_DATA1_SPI_IRQ SDIO 4-bit Mode: Data line 1 or Interrupt SDIO 1-bit Mode: Interrupt This pin has an internal weak pull-up resistor. The resistor is enabled by default but can be disabled by software. The value of the pull-up depends on the VDDIO_SD supply voltage. For 1.8V, the resistance range is 30–82 k Ohms. For 2.6V, it ranges from 21–41 k Ohms. For 3.3V, it ranges from 15–35 k ohms. I/O -23-
-24-Pin No Pin Name Description Type44 WL_GPIO_1 Reserved pin. WLAN general purpose interface pins. The pin is high-impedance on power up and reset. Subsequently, they become inputs or outputs through software control. The pin has programmable pull-up/down. 45 SDIO_CMD_SPI_DI SDIO 4-bit Mode: Command line SDIO 1-bit Mode: Command line This pin has an internal weak pull-up resistor. The resistor is enabled by default but can be disabled by software. The value of the pull-up depends on the VDDIO_SD supply voltage. For 1.8V, the resistance range is 30–82 k Ohms. For 2.6V, it ranges from 21–41 k Ohms. For 3.3V, it rangesfrom 15–35 k ohms I/O 46 BT_GPIO_2 Reserved pin. Bluetooth general purpose interface pin. The pin is high-impedance on power up and reset. Subsequently, they become inputs or outputs through software control. 47 SDIO_DATA0_SPI_DO SDIO 4-bit Mode: Data line 0 SDIO 1-bit Mode: Data line This pin has an internal weak pull-up resistor. The resistor is enabled by default but can be disabled by software. The value of the pull-up depends on the VDDIO_SD supply voltage. For 1.8V, the resistance range is 30–82 k Ohms. For 2.6V, it ranges from 21–41 k Ohms. For 3.3V, it rangesfrom 15–35 k ohms I/O 48 VDDIO_SD SDIO/SPI I/O supply (1.8V ~ 3.3V) I 49 BT_SHUTDOWN_N Used by PMU (along with WL_SHUTDOWN_N_RST_N) to decide whether or not to power down internal BCM4329 regulators. If both BT_SHUTDOWN_N and WL_SHUTDOWN_N_RST_N are low then the regulators will be disabled. This signal has an internal 200 k ohms pull-down resistor. The minimum Vih for this pin is 1.36V; the maximum is 3.3V ± 10%. I 50 GND Ground 51 RTC_CLK Real Time Clock 32.768KHz input (Auto-detection of frequencies requires that the RTC_CLK frequency drift < 200 ppm. I 52 NC No Connect ※ All of pin definition for module side
3-2. Pin Description comparison with PCI-Express specification ※ All of pin definition for module side PCI-Express Definition AW-NH930 Definition PCI-Express Definition AW-NH930 Definition Pin No Name Name Pin No Name Name 1 WAKE# WL_HOST_WAKE 2 3.3Vaux VBAT3V3_IN 3 Reserved BT_PCM_IN 4 GND GND 5 Reserved BT_PCM_OUT 6 1.5V N/A 7 CLKREQ# BT_HOST_WAKE 8 Reserved BT_UART_CTS_N 9 GND GND 10 Reserved BT_UART_TXD 11 RFCLK- FM_AUDIO_L 12 Reserved BT_UART_RXD 13 RFCLK+ FM_AUDIO_R 14 Reserved BT_UART_RTS_N 15 GND GND 16 Reserved BT_WAKE 17 Reserved BT_PCM_SYNC 18 GND GND 19 Reserved BT_PCM_CLK 20 Reserved BT_RST_N 21 GND GND 22 PERST# WL_RST_N 23 PERn0 N/A 24 3.3Vaux VBAT3V3_IN 25 PERp0 N/A 26 GND GND 27 GND GND 28 1.5V VDDIO 29 GND GND 30 SMB_CLK N/A 31 PETn0 N/A 32 SMB_DATA N/A 33 PETp0 N/A 34 GND GND 35 GND GND 36 USB_D- N/A 37 Reserved SDIO_DATA2_SPI_NC 38 USB_D+ N/A 39 Reserved SDIO_CLK_SPI_CLK 40 GND GND 41 Reserved SDIO_DATA3_SPI_CS 42 LED_WWAN# WL_SHUTDOWN_N 43 Reserved SDIO_DATA1_SPI_IRQ 44 LED_WLAN# WL_GPIO_1 45 Reserved SDIO_CMD_SPI_DI 46 LED_WPAN# BT_GPIO_2 47 Reserved SDIO_DATA0_SPI_DO 48 1.5V VDDIO_SD 49 Reserved BT_SHUTDOWN_N 50 GND GND 51 Reserved RTC_CLK 52 3.3Vaux N/A -25-
4. Mechanical Information The size and thickness of the AW-NH930 module is listed below: -26-Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: TLZ-NH930”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
-27-5. Antenna port Information

Navigation menu