AzureWave Technologies NM230NF IEEE 802.11 b/g/n Wireless LAN and Bluetooth combo M.2 1216 module User Manual AW AH691A

AzureWave Technologies, Inc. IEEE 802.11 b/g/n Wireless LAN and Bluetooth combo M.2 1216 module AW AH691A

Users Manual-2

 - 1 - AW-NM230NF IEEE 802.11 b/g/n Wireless LAN and Bluetooth Combo M.2 1216 Module  User Guide  Document release Date Modification Initials Approved Version 0.1 2015/03/10 Initial Version Chao Lee Amos Fu Version 0.2 2015/8/3 Add Pin definition / pin map Chao Lee Amos Fu  1. WLAN Basic Test  Driver Installation  Throughput Test  RF Tx/Rx Performance Test 2. Bluetooth Basic Test  Download Mini-driver  Throughput Test  RF Performance Test 3. Statement 4. Pin definition / pin map
 - 2 - 1. WLAN Basic Test **Must connect USB to PC Driver Installation DRIVER INSTALLATION (IN LINUX) •First prepare the Broadcom’s linux package, and put it in the “home”folder. •Open the Terminal, enter the command: sudo su and password. •Enter cd /home/username/drivername/src/dhd/linux •Enter make dhd-cdc-sdmmc-gpl to generate the dhd.ko file in /home/username/ drivername /src/dhd/linux/dhd-cdc-sdmmc-gpl-kernelversion •Enter   Insmod /(path of dhd.ko file)   firmware_path=/(path of firmware file)    nvram_path=/(path of nvram file) to enable. •Enter rmmod dhd to disable  Throughput Test  CONNECTING TO WIRELESS NETWORKS The examples in the following sections illustrate how to connect to both infrastructure and ad hoc networks, including infrastructure networks that use no security, WEP security, and WPA/PSK and WPS2/PSK security.  SCANNING FOR WIRELESS NETWORKS To force the dongle to scan • Run wl scan. To force the dongle to return the results of the scan • Run wl scanresults. Example results returned when an AP is found: • SSID: “Eval4325” • Mode: Managed: RSSI: -48 dBm noise: -105 dBm Channel: 1 • BSSID: 00:10:18:90:2E:C1 Capability: ESS ShortSlot • Supported Rates: [ 1(b) 2(b) 5.5(b) 11(b) 18 24 36 54 6 9 12 48 ] Example results returned when an ad hoc network is found: • SSID: “ADHOC#1” • Mode: Ad Hoc RSSI: -41 dBm noise: -105 dBm Channel: 1
 - 3 - • BSSID: B2:51:28:6B:3C:A1 Capability: IBSS • Supported Rates: [ 1(b) 2(b) 5.5(b) 11(b) ]  CONNECTING TO AN INFRASTRUCTURE NETWORK WITH NO SECURITY (AP CONNECTION) To connect to the network through an AP with SSID = Eval4325 Run wl join Eval4325.  CONNECTING TO AN INFRASTRUCTURE NETWORK WITH WEP SECURITY To connect to the network that uses 12345 as the network key • Run wl join Eval4325 key 12345.  CONNECTING TO AN INFRASTRUCTURE NETWORK WITH WPA-PSK/WPA2-PSK SECURITY To specify TKIP or AES as the data encryption method • Run wl wsec 3/7. To enable the supplicant • Run wl sup_wpa 1. To specify the PSK passphrase (network key) to use • Run wl set_psk $passphrase. To connect to a network that uses WPA-PSK security • Run wl join Eval4325 imode bss amode wpapsk. To connect to a network that uses WPA2-PSK security • Run wl join Eval4325 imode bss amode wpa2psk.  CONNECTING TO AN AD HOC NETWORK USING CHANNEL 1 To set the channel to channel 1 • Run wl channel 1. To connect to the ad hoc network with SSID = 4325-ADHOC • Run wl join 4325-ADHOC imode ibss.  MANAGING POWER CONSUMPTION To disable Power Save (PS) mode (default) • Run wl PM 0. To enable legacy IEEE 802.11 Power Save (PS) mode • Run wl PM 1. To enable Fast IEEE 802.11 Power Save mode • Run wl PM 2.
 - 4 - Note: • The STA automatically transitions to Legacy PS mode when no data is being sent or received. • The STA automatically disables PS mode when data is being sent or received.  MEASURING WLAN THROUGHPUT The throughput measurement shows the performance of the TCP/IP layer over the wireless link. To achieve the best results, run the measurement test in a clean environment with as little interference as possible . The test can be run with the adapter connected to either an Infrastructure network (see Fig. 2.2) or an ad hoc network (see Fig. 2.3). An AP that is known to be in good working order should be used for the infrastructure mode test.      MEASURING THROUGHPUT USING NETIQ CHARIOT Test Procedure 1. Bring up the AW-NM230NF demo boar with the IP address set as 192.168.1.110. 2. Connect the reference computer with Chariot Console, which is assigned an IP address of 192.168.1.100, to the LAN HOST COMPUTER. AW-NM230NF EndPoint Reference Computer Chariot Console HOST COMPUTER. AW-NM230NF EndPoint AP LAN Port Reference Computer Chariot Console FIG. 2.2 FIG. 2.3
 - 5 - port of the AP 3. Verify that communication exists between the reference computer and the AW-NM230NF demo board by pinging 192.168.1.100 from the AW-NM230NF host console. 4. Set up Chariot. a. On the host computer, activate    EndPoint: b. Using Chariot Console on the reference computer, create two pair groups (192.168.1.100 and 192.168.1.110) using the Chariot Throughput.scr script. Run the throughput test for a specified period of time and observe the results.   RF Tx/Rx Performance Test CREATING A Tx TEST (In Ubuntu linux 12.04) 1. Open the Terminal, enter the command: sudo su and password. 2. Enter   Insmod /(path of dhd.ko file)   firmware_path=/(path of firmware file)    nvram_path=/(path of nvram file) to enable. 3. Enter the wl ver command to check the current WL driver version. 4. Run the following command set (delay at least 700ms between each command):  11b rate:  ./wl mpc 0 ./wl country ALL ./wl up ./wl scansuppress 1 ./wl band b ./wl channel 7 ./wl nrate -r 11 ./wl txpwr1 -o -q 68 ./wl phy_forcecal 1 ./wl pkteng_start 00:11:22:33:44:55 tx 300 1500 0   This will send continuous Tx Packets with 300 us packet interval,1500 byte packet length. Data rate =11Mbps ,Channel=7 and output power =17dBm(68/4=17 q means quarter).
 - 6 - 11g rate:  ./wl mpc 0 ./wl country ALL ./wl up ./wl scansuppress 1 ./wl band b ./wl channel 7 ./wl nrate -r 54 ./wl txpwr1 -o -q 60 ./wl phy_forcecal 1 ./wl pkteng_start 00:11:22:33:44:55 tx 300 1500 0  This will send continuous Tx Packets with 300 us packet interval,1500 byte packet length. Data rate =54Mbps ,Channel=7 and output power =15dBm(60/4=15 q means quarter).   2.4G 11n 20 SISO rate: ./wl mpc 0 ./wl country ALL ./wl up ./wl scansuppress 1 ./wl band b   ./wl channel 7 ./wl nrate -m 7 ./wl chanspec -c 7 -b 2 -w 20 -s 0 ./wl txpwr1 -o -q 52 ./wl phy_forcecal 1 ./wl pkteng_start 00:11:22:33:44:55 tx 300 1500 0  This will send continuous Tx Packets with 300 us packet interval,1500 byte packet length. Data rate =MCS7, Bandwidth=20Mhz, Channel=7 and output power =13dBm(52/4=13 q means quarter).
 - 7 - CREATING A Rx TEST  (In Ubuntu linux 12.04) 1. Open the Terminal, enter the command: sudo su and password. 2. Enter   Insmod /(path of dhd.ko file) firmware_path=/(path of firmware file) nvram_path=/(path of nvram file)   to enable. 3. Enter the wl ver command to check the current WL driver version. 4. Run the following command set    11b/g rate:  ./wl mpc 0 ./wl phy_watchdog 0 ./wl country ALL ./wl band b   ./wl channel 7 ./wl up ./wl phy_forcecal 1 ./wl scansuppress 1 ./wl rxchain 1 ./wl reset_cnts ./wl counters  This will enter Channel 7 receive mode.    2.4G 11n 20 SISO rate:  ./wl mpc 0 ./wl phy_watchdog 0 ./wl country ALL ./wl band b ./wl channel 7   ./wl up
 - 8 - ./wl phy_forcecal 1 ./wl scansuppress 1 ./wl rxchain 1   ./wl reset_cnts ./wl counters   This will enter Channel 7 receive mode.  ※.The default MAC address is 001122334455. Packets sent from Signal Generator must have the same MAC address as the DUT’s MAC address (Runtime mac address can be overrode by using wl cur_etheraddr xx:xx:xx:xx:xx:xx .  ※. Use “./wl counters” and find the received frame numbers in “rxdfrmocast”. ※. The RX PER = [ (Total lost packets at the receiver) / (Total sent packets from the Signal Generator) ] x 100%. Thus,  PER  =100%  -  [(rxdfrmocast  numbers  after  sequence  play)  –  (rxdfrmocast  numbers  before  sequence  play)]  / (Total sent packets from the signal Generator) x 100%. .    2. Bluetooth Basic Test *Must connect USB to PC Download Mini-driver  1. Start Broadcom BlueTool. 2. On the View menu, click Log Windows Details. 3. On the Transport menu, click HCI Control.
 - 9 -  4. In Select HCI Control Window Transport: a. Select UART as the type of transport. b. In the COM port list, select com6.(check the port number in device manager)
 - 10 -  c. In the Baud list, type 115200. d. Select the CTS flow control check box. e. Click OK. 5. In HCI Control, select the HCI protocol active check box  6. In the HCI Control commands list, select 0: Vendor-specific Commands (0 key), and then double-click Download Minidriver.
 - 11 - 7. On the Transport menu, click Download Firmware/Config. 8. In Select Download Firmware/Config Transport:  a. Select UART as the type of transport. b. In the COM port list, select com6. c. In the Baud list box, type 115200. d. Select the CTS flow control check box. e. Click OK. 9. In Download, configure the settings to match those shown below  10. Click Execute.   11. Select the HCI protocol active check box
 - 12 - Throughput Test Bluetool contains a throughput test feature that can be used with two or more  AW-NM230NF devices.    Note that each device runs on a separate PC with BlueTool installed.    This document will provide basic directions for setting-up and running this test.  The next step in setting-up the test is establishing a connection between the devices. ESTABLISH A BLUETOOTH CONNECTION BETWEEN TWO USB DEVICES SET UP THE SLAVE DEVICE FIRST  1. On the Slave side, start Bluetool from the Start Menu. 2. If the Log Window is not already open, select “View” and then select “Log Window”.Select “Transport” and then Select “HCI Control.” New window pop-up, select “UART” and enter com port number. Click “OK”. 3. Download mini driver (see 3.1) 4. In the “HCI Control” window, select “7.3 Host Controller & Baseband Commands”    (Note: may be 4.3, depending on version) 5. Double Click the “Write Scan Enable” entry 6. Select “Inquiry and Page Scan Enabled” and click “OK” 7. Double Click “Set Event Filter” 8. Select “Connection Setup” 9. Select “Allow Connections from all devices” 10. Select “Do Auto accept the connection with role switch disabled” 11. Click “OK” 12. In the “HCI Control” window, select “0 Vendor-specific commands”. 13. Double Click the “Write_BD_ADDR” command 14. Enter 001122334455 15. In the “HCI Control” window,select”0 Vendor-specific commands”. Double Click ”Update UART Baud Rate”. Select 3000000 then click OK.  SET UP THE MASTER DEVICE, AND CREATE THE CONNECTION 1. On the Master side, start Bluetool. 2. Open the log window, if not already open, and open the UART HCI Transport. 3. Download mini driver (see 3.1) 4. In the “HCI Control” window, select “7.1 Link Control Commands”    (Note: may be 4.5 depending on version)
 - 13 - 5. Double Click “Create Connection” and put BD address of the slave device into the BDADDR box.    Click “OK” 6. In the “HCI Control” window,select”0 Vendor-specific commands”. Double Click ”Update UART Baud Rate”. Select 3000000 then click OK.  A connection should establish now.    This can be verified by looking in the log windows for both devices, which should now contain Connection Complete events with “Success” in the status field.      NOTE:  once  the  connection  has  been  established,  Inquiry  and  Page  Scan  can  be  disabled.    Also,  go  to:  “7.3  Host Controller &  Baseband  Commands”  →→  “Set  Event  Filter”.    Select “Connection Setup”;  Select  “Allow  Connections from  all  devices”;  Select  “Do  NOT  Auto  accept  the  connection”  and  hit  ‘OK’.    This  will  make  the  slave  device non-discoverable and increase throughput by reducing overhead.        SET UP AND EXECUTE THE THROUGHPUT TEST SET UP THE SLAVE AS THE RECEIVER 1. On the Slave side, select “Transport” and then select “Throughput Tests”.    Select UART. 2. In the “Receive Test” (Bottom half of the window), fill in a data pattern such as “abcdef”, and fill in a count such as “1000000” 3. Close the “Log Window.”    If this window is left open or minimized, then the throughput test will not achieve maximum throughput because of delay that is added by Windows every time the log window is updated.  SET UP THE MASTER AS THE TRANSMITTER AND START THE TEST 1. On the Master side, select “Transport” and then select “Throughput Tests”.    Select UART. 2. In the “Transmit Test” window (top half of the window), fill in the same data pattern and count that was filled in for the receive test on the Slave side. 3. Close the “Log Window.”    If this window is left open or minimized, then the throughput test will not achieve maximum throughput because of delay that is added by Windows every time the log window is updated. 4. On the Slave side, click “Execute Test” in the “Receive Test” window. 5. On the Master side, click “Execute Test” in the “Transmit Test” window. Bluetooth throughput test is now running.  To stop the test, click “Abort Test” on the Master side first, then on the slave side.
 - 14 - RF Performance Test  The following procedure explains how to configure the AW-NM230NF for RF testing using Broadcom BlueTool. At the completion of the procedure, connect the Bluetooth test instrument to the AW-NM230NF with RF cable and performs the RF tests.   RESETTING THE USB DEVICE To reset the USB device •In HCI Control, in the HCI Control commands list, select 7.3: Host Controller & Baseband Commands (3 key), and then double-click Reset.  READING THE BLUETOOTH DEVICE ADDRESS To read the Bluetooth Device Address • In HCI Control, in the HCI Control commands list, select 7.4: Informational Parameters (4 key), and then double-click Read_BD_ADDR. The Bluetooth Device Address (BD_ADDR) is displayed in the log window. The Bluetooth Device Address might be needed by the Bluetooth tester  SETTING THE EVENT FILTER TO AUTOMATICALLY ALLOW CONNECTION To set the event filter to automatically allow connection 1. In HCI Control, in the HCI Control commands list, select 7.3: Host Controller & Baseband Commands (3 key), and then double-click Set_Event_Filter. 2. In HCI Command: Set_Event_Filter: a. In the Filter_Type list, select Connection Setup. b. In the Connection_Setup_Filter_Condition_Type list, select Allow Connections from all devices. c. In the Auto_Accept_Flag list, select Do Auto accept the connection with role switch disabled.  ENABLING WRITE SCAN To enable Write Scan 1. In HCI Control, in the HCI Control commands list, select 7.3: Host Controller & Baseband Commands (3 key), and then double-click Write_Scan_Enable. 2. In HCI Command: Write_Scan_Enable, in the Scan_Enable list, select Inquiry and Page Scan enabled.  ENABLING TEST MODE
 - 15 - To enable Test Mode • In HCI Control, in the HCI Control commands list, select 7.6: Testing Commands (6 key), and then double-click Enable_Device_Under_Test_Mode. The AW-NM230NF is now ready to receive a connection request from the Bluetooth tester and begin testing specified RF parameters.   3.Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance  with  the  instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA
 - 16 - This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and   2) The transmitter module may not be co-located with any other transmitter or antenna,   3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.  As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed  IMPORTANT NOTE In  the  event  that  these  conditions  can  not  be  met  (for  example  certain  laptop  configurations  or  co-location  with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final  product.  In  these  circumstances,  the  OEM  integrator  will  be  responsible  for  re-evaluating  the  end  product (including the transmitter) and obtaining a separate FCC authorization.  End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be  maintained  between  the  antenna  and  users.  The  final  end  product  must  be  labeled  in  a  visible  area  with  the following: “Contains FCC ID: TLZ-NM230NF”.  Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
 - 17 - Industry Canada statement: This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:   (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.   Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1)  Ce  dispositif  ne  peut  causer  d'interférences;  et(2)  Ce  dispositif  doit  accepter  toute  interférence,  y  compris  les interférences qui peuvent causer un mauvais fonctionnement de l'appareil.  Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.  Déclaration d'exposition aux radiations: Cet  équipement  est  conforme  aux  limites  d'exposition  aux  rayonnements  IC  établies  pour  un  environnement  non contrôlé.  Cet  équipement  doit  être  installé  et  utilisé  avec  un  minimum  de  20  cm  de  distance  entre  la  source  de rayonnement et votre corps.
 - 18 - This device is intended only for OEM integrators under the following conditions:    1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and   2) The transmitter module may not be co-located with any other transmitter or antenna.  As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.  Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:  1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.  Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois,  l'intégrateur  OEM  est  toujours  responsable  des  essais  sur  son  produit  final  pour  toutes  exigences  de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In  the  event  that  these  conditions  can  not  be  met  (for  example  certain  laptop  configurations  or  co-location  with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final  product.  In  these  circumstances,  the  OEM  integrator  will  be  responsible  for  re-evaluating  the  end  product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans  le  cas  où  ces  conditions  ne  peuvent  être  satisfaites  (par  exemple  pour  certaines  configurations  d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be  maintained  between  the  antenna  and  users.  The  final  end  product  must  be  labeled  in  a  visible  area  with  the following: “Contains IC: 6100A-NM230NF”.
 - 19 - Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs.  Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6100A-NM230NF ".  Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.  Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.  This radio transmitter (IC: 6100A-NM230NF) has been approved by Industry Canada to operate with the antenna types listed  below  with  the  maximum  permissible  gain  indicated.  Antenna  types  not  included  in  this  list,  having  a  gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device  Cet  émetteur  radio  (IC:  6100A-NM230NF)  a  été  approuvé  par  Industrie  Canada  pour  fonctionner  avec  les  types d'antenne énumérés ci-dessous avec le gain maximal admissible indiqué. Types d'antennes ne figurent pas dans cette liste, ayant un gain supérieur au gain maximum indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil  Model Type   Connector Gain (dBi) RFMTA340715IMLB301 PIFA I-PEX 3
 - 20 - Taiwan  警語: 第十二條→經型式認證合格之低功率射頻電機,非經許可,公司,商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。  第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。  1.  本模組於取得認證後將依規定於模組本體標示審驗合格標籤   2.  系統廠商應於平台上標示「本產品內含射頻模組:   CC XX xx YY yyy Z z W」字樣
 - 21 - 4. Pin Definition / Pin Map Pin No Definition Basic Description Type Voltage 1 NC No Connect Floating  2 NC No Connect Floating  3 NC No Connect Floating  4 3.3V 3.3V power pin VCC 3.3V 5 3.3V 3.3V power pin VCC 3.3V 6 GND Ground. GND  7 NC No Connect Floating  8 NC No Connect Floating  9 NC No Connect Floating  10 NC No Connect Floating  11 SECI_TX_GPIO1 GPIO pin I/O 1.8V 12 SECI_RX_GPIO2 GPIO pin I/O 1.8V 13 NC No Connect Floating  14 NC No Connect Floating  15 NC No Connect Floating  16 NC No Connect Floating  17 GND Ground. GND  18 NC No Connect Floating  19 NC No Connect Floating  20 GND Ground. GND  21 NC No Connect Floating  22 NC No Connect Floating  23 GND   Ground GND  24 BT_DEV_WAKE BT Device Wake   I 1.8V 25 NC No Connect Floating  26 GND Ground GND  27 CLK_32KHz External sleep clock input (32.768 kHz). I 1.8V 28 WL_REG_ON Used  by  PMU  to  power  up  or  power  down  the internal  regulators  used  by  the  WLAN  section. Also, when deasserted, this pin holds the WLAN section  in  reset.  This  pin  has  an  internal  200k I 1.8V
 - 22 - ohm  pull  down  resistor  that  is  enabled  by default. It can be disabled through programming.   29 NC No Connect Floating  30 NC No Connect Floating  31 NC No Connect Floating  32 GND Ground GND  33 NC No Connect Floating  34 NC No Connect Floating  35 GND Ground GND  36 NC No Connect Floating  37 NC No Connect Floating  38 GND Ground   GND  39 NC No Connect Floating  40 NC No Connect Floating  41 GND Ground GND  42 NC No Connect Floating  43 NC No Connect Floating  44 NC No Connect Floating  45 WL_REG_ON Used  by  PMU  to  power  up  or  power  down  the internal  regulators  used  by  the  WLAN  section. Also, when deasserted, this pin holds the WLAN section  in  reset.  This  pin  has  an  internal  200k ohm  pull  down  resistor  that  is  enabled  by default. It can be disabled through programming.     I 1.8V 46 WL_HOST_WAKE WL Host Wake O 1.8V 47 SDIO DATA3 SDIO Data Line 3 I/O 1.8V 48 SDIO DATA2 SDIO Data Line 2 I/O 1.8V 49 SDIO DATA1 SDIO Data Line 1 I/O 1.8V 50 SDIO DATA0 SDIO Data Line 0 I/O 1.8V 51 SDIO CMD SDIO Command Input I/O 1.8V 52 SDIO CLK SDIO Clock Input I 1.8V 53 BT_HOST_WAKE BT Host Wake   O 1.8V 54 UART CTS High-Speed UART CTS I 1.8V 55 UART Tx High-Speed UART Data Out O 1.8V 56 UART Rx High-Speed UART Data In I 1.8V
 - 23 - 57 UART RTS High-Speed UART RTS O 1.8V 58 PCM_SYNC PCM Synchronization control O 1.8V 59 PCM_IN PCM data Input I 1.8V 60 PCM_OUT PCM data Out O 1.8V 61 PCM_CLK PCM Clock I/O 1.8V 62 GND Ground   GND  63 BT_REG_ON Used by PMU to power up or power down the internal regulators used by the Bluetooth section. Also, when deasserted, this pin holds the Bluetooth section in reset. This pin has an internal 200k ohm pull down resistor that is enabled by default. It can be disabled through programming. I 1.8V 64 NC No Connect Floating  65 NC No Connect Floating  66 NC No Connect Floating  67 NC No Connect Floating  68 GND Ground   GND  69 NC No Connect Floating  70 NC No Connect Floating  71 GND Ground   GND  72 3.3V 3.3V power pin VCC 3.3V 73 3.3V 3.3V power pin VCC 3.3V 74 GND Ground   GND  75 GND Ground   GND  76 GND Ground   GND  77 GND Ground   GND  78 GND Ground   GND  79 GND Ground   GND  80 GND Ground   GND  81 GND Ground   GND  82 GND Ground   GND  83 GND Ground   GND  84 GND Ground   GND  85 GND Ground   GND
 - 24 - 86 GND Ground   GND  87 GND Ground   GND  88 GND Ground   GND  89 GND Ground   GND  90 GND Ground   GND  91 GND Ground   GND  92 GND Ground   GND  93 GND Ground   GND  94 GND Ground   GND  95 GND Ground   GND  96 GND Ground   GND  G1 GND Ground   GND  G2 GND Ground   GND  G3 GND Ground   GND  G4 GND Ground   GND  G5 GND Ground   GND  G6 GND Ground   GND  G7 GND Ground   GND  G8 GND Ground   GND  G9 GND Ground   GND  G10 GND Ground   GND  G11 GND Ground   GND  G12 GND Ground   GND
 - 25 - AW-NM230NF Top View Pin Map

Navigation menu