User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2030440 |
| Application ID | RNY/p3UOfxCi+XpDcNgUPw== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 8.3kB (103697 bits) |
| Date Submitted | 2013-08-01 00:00:00 |
| Date Available | 2013-08-01 00:00:00 |
| Creation Date | 2013-05-08 18:00:29 |
| Producing Software | GPL Ghostscript 9.06; modified using iText® 5.3.2 ©2000-2012 1T3XT BVBA (AGPL-version) |
| Document Lastmod | 2013-08-01 10:04:07 |
| Document Title | User manual |
| Document Creator | CubePDF |
Transmitter
*Using the Transmitter
＊ Names of parts
① Power switch
② LCD
Ａ Channel display
Ｃ Battery indicator
Ｄ Save mode display
③ Volume button （Up)
④ Volume button （Down)
⑤ Channel button (Up)
⑥ Channel button (Down)
⑧ Microphone jack
⑨ Battery cap
⑩ External microphone
＊Before to use
Ｉ ： How to replace battery
Turn the battery cap 90 degrees by using coins
in the counterclockwise direction, and remove the
cap.
When open the battery cap, batteries can be
seen. Take out batteries by gently tilt the device.
(Please note that batteries fall easily.)
As shown in the upper right phote, put two AA alkaline batteries in the battery case.
Make sure the plus side of batteries (convex) comes to the cap side.
While pressing, turn the battery cap 90 degrees int the clockwide direction until it locked.
ＩI ： Insert the plug of an external microphone all the way into the microphone jack,
until you hear "click" sound.
Power-On
Push power switch button ①, and indication will appears on ② LCD. Lamp is
lit on the display for 2 seconds.
Power-Off
Push power switch button ① for more than 1 second -- the power is turned
off.
Transmitter1
Transmitter
* The following operations are performed while the power is on.
Change Channels ("A"part of the LCD)
・ Press the channel button ⑤(+CH) once, and one channel up.
Goes up to "16" channels, and then will return to "01."
・ Press the channel button ⑥(-CH) once, and one channel down.
Battery Indicator ("C"part of the LCD)
・ 2 seconds after the power turned on, the battery level is displayed in 5 steps
below.
・ When lines of the display becomes 0 (None), replace batteries.
Blinking = End
Full
↑Replace batteries
Transmission ("D"part of the LCD)
・ Accordance with the same transmitter and receiver channels.
When speak into the microphone, the device start transmission automatically,
and "TX" appears on LCD.
Battery Save Mode ("D"part of the LCD)
・ If there is no voice input for 20 seconds, "TX"display of the LCD will blink.
Then, the device will enter "battery save mode"-- to prevent battery drain.
・ While in "battery save mode," the device stands up automatically with any
operations (such as voice input, button operation).
Auto Power Off
・ The device automatically turns off, after 1hour of non use.
Transmitter2
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission Requirements
The equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient of relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
THE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de license. L'exploitation est autorisee aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage
est susceptible d'en compromettre le fonctionnement.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Format : application/pdf Creator : Description : Title : Create Date : 2013:05:08 18:00:29+09:00 Creator Tool : CubePDF Modify Date : 2013:08:01 10:04:07+08:00 Metadata Date : 2013:08:01 10:04:07+08:00 Keywords : Producer : GPL Ghostscript 9.06; modified using iText® 5.3.2 ©2000-2012 1T3XT BVBA (AGPL-version) Document ID : uuid:e6e6fa19-14f0-4271-8634-6f206c84176b Instance ID : uuid:f1d8d381-83f9-4b2d-9815-11bbe5e9fd82 Page Count : 3 Subject : Author :EXIF Metadata provided by EXIF.tools