BAOLONG AUTOMOTIVE VSENSOR Tyre Pressure Sensor User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	3324550
Application ID	mlGO7jSWXoE71E1SdP/b2A==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.78kB (384807 bits)
Date Submitted	2017-03-20 00:00:00
Date Available	2017-03-20 00:00:00
Creation Date	2017-03-20 23:35:37
Producing Software	LibreOffice 5.2
Document Lastmod	0000-00-00 00:00:00
Document Title	Users manual
Document Creator	Draw

OPERATION MANUAL OF EXTREME DUTY TPMS SENSOR
Quick Use Notice
Please Read Before Installation
· Handling of tires and rims should be carried out only by workers who have
received training and accreditation based on instruction from a qualified work
supervisor.
· Check the “Tire and Rim Handling Manual” published by the tire manufacturer
for information on work and inspections, etc. involving tire handling.
· When lifting heavy components or equipment, make sure that you use suitable
lifting equipment and that you follow the instructions in the manual for
equipment to be used.
· When moving tires and rims, be careful to avoid accidental drops or falls that
could injure others in the vicinity.
· There are several types of tools for work involving tire and rim handling. Be
sure you have proper understanding of how the tools are used and carry out the
work in accordance with proper procedures.
· Be sure to perform a visual examination of tires and rims when conducting
regular inspections of vehicles and tires or tire rotations.
· Use tires and rims suited to the vehicle, as specified by the vehicle
manufacturer and tire manufacturer.
· In the case of dual assemblies, DO NOT operate the vehicle on a single tire as
the load capacity of the tire and rim will be drastically reduced and may result in
damage
FCC’s Authentication Announcements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and complies with the limits for a Class B digital device, pertaining to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment.
This equipment can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will occur in a
particular installation. You can test whether this equipment does cause harmful interference to radio or television reception
by turning the equipment off or on.
INSTALLATION GUIDE
Mounting CV TPMS Sensor
Before installation, identify each pair of transmitter and ID module. There
are two labels coming with each pair of transmitter & ID module, and they
have the same ID code. For example: 01EB327F.
Install the transmitter onto the wheel and place the rim label on the rim.
Plug ID Module into Display (Refer to Operation of Display)
1. Loosen the steel strap. Wrap the strap around the centre of the rim in
the lowest spot and mark it 5 cm (2”) past worm gear. (Figure A)
2. Cut the extra strap. Install the tapered end of the strap through the
opening of the transmitter cradle. (Figure B)
3. Remove the adhesive tape liner from cradle and place transmitter
beside the tyre valve. Keep the strap parallel to the wheel flange and
ensure the strap is positioned in the lowest spot possible for correct
transmitter and cradle retention. (Figure C)
NOTE: The transmitter must be positioned in the lowest spot possible and
installed beside the tyre valve in order to know its approximate location
after the tyre has been mounted.
NOTE: When fixing the transmitter on the rim, make sure the section of
steel strap installed through the transmitter is complete, NOT TOOTHED.
(Figure D)
4. Position worm gear 10 cm (4”) away from the edge of the transmitter
and tighten worm gear until the transmitter cannot be moved. DO NOT
over tighten the strap, reference torque: 3-4 Nm (27-35 inch lbs.)
(Figure E)
5. Indicate the location and ID code of the transmitter by applying the
supplied rim label to a clean and dry location on the rim.
SHANGHAI BAOLONG AUTOMOTIVE CORPORATION
5500, Shenzhuan Rd., Songjiang, Shanghai 201619, China
Tel.: +86-21-31273333
Fax: +86-21-31190319
E-mail: sbic@baolong.biz
Web: www.baolong.biz

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
Creator                         : Draw
Producer                        : LibreOffice 5.2
Create Date                     : 2017:03:20 23:35:37+01:00

EXIF Metadata provided by EXIF.tools