BARCO AMM190WTD LCD Display User Manual AMM190WTD RevA1 111809 indd
Advan Int'l Corp. LCD Display AMM190WTD RevA1 111809 indd
BARCO >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1289760 |
| Application ID | rzukxJNhboCEF41XoV3SHg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 75.38kB (942272 bits) |
| Date Submitted | 2010-06-02 00:00:00 |
| Date Available | 2010-06-02 00:00:00 |
| Creation Date | 2009-11-18 18:31:02 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2009-12-11 15:02:15 |
| Document Title | AMM190WTD RevA1 111809.indd |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | ericlau |
ADVAN AUTO - SCANNING WITH DIGITAL CONTROL LCD COLOR MEDICAL MONITOR AMM190WTD Operation Manual For future reference, record the serial number of your display monitor in the space below : Serial Number The serial number is located on the back of the monitor AMM190WTD 1 ENGLISH back of the monitor WARNING The title «WARNING» is used to inform the users of possible causes that could inflict the injury, death, or property damage to the patients. CAUTION The title «CAUTION» is used to inform the users of possible causes that could inflict the patients although it might not severe enough to cause deaths. NOTE The title «NOTE» is used to inform the users of items that are of importance in terms of installation, operation, or maintenance of the Equipment although the failure does not inflict the bodily harm to the patients. ADVAN INT’L CORP.2009 All other trademarks are the property of their reference owners. This document is subject to change without notice. Advan provides this information as reference only. Reference to other vendor’s products does not imply any recommendation or endorsement. Revision Control Date Description REV.03 111809 Document number 2 User’s Guide TABLE OF CONTENTS Product Description and Intended Use ...................................................... 3 Warnings and Cautions ............................................................................. 4 Symbol Explanations ................................................................................. 7 EU Declaration of Conformity for Medical Applications ............................. 8 Safety Precaution ...................................................................................... 9 Cleaning Your Monitor ............................................................................... 9 Power Management Function.................................................................... 10 Preset Modes.............................................................................................. 11 Video Signals............................................................................................. 12 PIP / POP / PBP function........................................................................... 13 DDC ........................................................................................................... 14 Installation ................................................................................................. 14 Connecting the Power Cord ...................................................................... 15 User Function / Messages......................................................................... 16 OSD Section .............................................................................................. 17 Troubleshooting ......................................................................................... 25 Specification of (AMM190WTD) ................................................................ 26 Classification ............................................................................................. 27 Electromagnetic Compatibility ................................................................... 28 Dimension Drawing (mm) of AMM190WTD............................................... 31 Connectors ................................................................................................ 32 Description of Warranty ............................................................................. 33 Product Description and Intended Use Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. • AMM190WTD LCD Monitor and two video cables (1) HD15 VGA cable* (1) DVI-D cable* • AC Power cord** • AC-Adapter • Composite Video BNC Jack Cable and Super Video Cable • User Manual and 4pcs VESA screws *Might be optional item, check with local representative **Might vary pending on region stardard CAUTION Model No : JMW1100KA1800F01 ENGLISH AMM190WTD 3 4 User’s Guide Warnings and Cautions Please read this manual and follow its instructions carefully. The words warning, caution, and note carry special meanings and should be carefully reviewed: Warning The personal safety of the patient or physician may be involved. Disregarding this information could result in injury to the patient or physician. Caution Special service procedures or precautions must be followed to avoid damaging the instrument. Note Special information to make maintenance easier or important information more clear. An exclamation mark within a triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product. A lightning bolt within a triangle is intended to warn of the presence of hazardous voltage. Refer all service to authorized personnel. Warning TO AVOID POTENTIAL SERIOUS INJURY TO THE USER AND THE PATIENT AND/OR DAMAGE TO THIS DEVICE, THE USER MUST : Warranty is void if any of these warnings are disregarded. ADVAN Int’l Corp accepts full responsibility for the effects on safety, reliability, and performance of the equipment only if: • Re-adjustments, modifications, and/or repairs are carried out exclusively by ADVAN Int’l Corp. • The electrical installation of the relevant operating room complies with the applicable IEC and CE requirements. Warning Federal law (United States of America) restricts this device to use by, or on order of a physician. The ADVAN Int’l Corp AMM190WTD monitor has been tested under UL 60601-1 standard and UL listed for Medical application. ADVAN Int’l Corp reserves the right to make improvements in the product(s) described herein. Product(s), therefore, may not agree in detail to the published design or specifications. All specifications are subject to change without notice. Please contact ADVAN Int’l Corp directly or phone your local ADVAN Int’l Corp sales representative or agent for information on changes and new products. 1. Read the operating manual thoroughly and be familiar with its contents prior to using this equipment. 2. Carefully unpack the unit and check if any damage occurred during shipment. 3. Should any solid object or liquid fall into the panel, unplug the unit and have it checked by qualified personnel before operating it any further. 4. Uplug the unit if it is not to be used for an extended period of time. To disconnect the cord, pull it out by the plug. Never pull the cord itself. 5. Be a qualified physician, having complete knowledge of the use of this equipment. 6. Test this equipment prior to a medical procedure. This monitor was fully tested at the factory before shipment. 7. Avoid removing covers on control unit to avoid electric shock. 8. Attempt no internal repairs or adjustments not specifically detailed in this operating manual. 9. Pay close attention to the care, cleaning instructions in this manual. A deviation may cause damage (refer to the Cleaning section). 10. DO NOT STERILIZE MONITOR. 11. Read the entire instruction manual before assembling or connecting the camera. 12. Do not place the monitor or any other heavy object on the power cord. Damage to the cable can cause fire or electirc shock. 13. Monitor with power supply is suitable for use in patient environment. 14. DO NOT stack more than 8 boxes high This equipment has been tested and found to comply with the limits for medical devices in IEC 601-1-2:2003. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving device. - Increase the separation between the equipment. - Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. - Consult the manufacturer or field service technician for help. NOTICES TO USER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipement generates or uses radio frequency energy. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. ENGLISH AMM190WTD 5 Warnings 6 User’s Guide Cautions 1. The AC Adapter must be plugged into a Grounded power outlet. 2. Use only the proprietary AMM190WTD power supply for the AMM190WTD monitor. Make a proper connection by ensuring that the shrink tubing completely secures the connection between the DC power cord and the extension cord. 3. Turn power off when unit is not in use. 4. Never operate the unit right after having transported from a cold location directly to a warm location. 5. Do not expose the monitor to moisture or directly apply liquid cleaners directly to the screen. Spray the cleaning solution into a soft cloth and clean gently. 6. Handle the monitor with care. Do not strike or scratch the screen. 7. Do not block the monitor cooling vents. The monitor is cooled by natural convection and has no fan. 8. Do not force the monitor past 28 degrees of vertical when adjusting the screen position. (For monitors equipped with stands only.) 9. Remove the power module and connection when transporting the unit. 10. Save the original carton and associated packing material. They will be useful should you have to transport or ship the unit. 11. Allow adequate air circulation to prevent internal heat buildup. 12. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots. 13. Do not install the unit near sunlight, excessive dust, mechanical vibration or shock. 14. The unit is designed for operation in a horizontal position. Never operate the unit in a vertical position. 15. Keep the unit away from equipment with strong magnets (i.e. a large loudspeaker.) 16. Do not expose the monitor to moisture or excessive dust. 17. Equipment with SIP/SOP connectors should either comply with IEC 60601-1 and/or IEC 60601-1-1 harmonized national standard or the combination should be evaluated. Do not touch the patient with signal input or output connectors. 18. Use only a hospital grade power supply cord. 19. This equipment has been tested and found to comply with the limit for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable generate uses and can radiate radio frequency energy, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, which can be detemined by turing the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving device. • Increase the separation distance between the equipment. • Connect the equipment to an outlet on a circuit different from that to which the other device(s) are connected. • Consult the manufacturer or field service technican for help. 20. Grounding reliability can only be achieved when the equipment is connected to an equipment receptacle labeled “Hospital Only” or “Hospital Grade.” Note To connect to an international power supply, use a an attachment plug appropriate for the power outlet. Note Refer to the “Electromagnetic Compatibility” (EMC) section of this manual to ensure EMC. The AMM190WTD must be installed and operated according to the EMC information provided in this manual. Dangerous: High Voltage Direct Current Serial Number Top – Bottom Fragile Do not get wet Consult accompanying documents. Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities. Authorized Representative in Europe Indicates protective earth ground. For indoor use only. Medical Equipment is in accordance with UL 60601-1 and CAN/ CSA C22.2 No. 601.1 in regards to electric shock, fire hazards, 51LJ Medical Equipment and mechanical hazards. E215822 Tested to comply with FCC Class B standards. DC power control switch ENGLISH AMM190WTD 7 Symbol Definitions 8 User’s Guide EU Declaration of Conformity for Medical Applications A Declaration of Conformity has been filed for this product. A sample of this document may be found in the addendum which accompanied this manual. For a copy of the Declaration of Conformity document, please contact ADVAN Int’l Corp. and request for AMM190WTD DOC. Prepare for Unpack Before you unpack your monitor, prepare a suitable workspace. You need a stable and level surface near a grounded wall outlet in an area which is relatively free of glare from sunlight or other sources of bright light. The monitor is cooled by natural convection (it has no fan). For optimum performance, do not block the cooling vents. While unpacking the monitor, inspect it and other package contents for shipping damage that could cause a fire or shock hazard. Immediately report any shipping damage to the carrier or transportation company and contact customer service for monitor in the future or in case of return. After you unpack the monitor, make sure the following items are included • Monitor with video cable • AC adapter with cable CAUTION: AC Adapter must be plugged into Grounded a power outlet CAUTION : AC adapter Model No: JMW1100KA1800F01 • This operations manual Note: Your system provider may offer alternative cords or cables depending on the installation requirement and local geography issues. AMM190WTD 9 · Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or electrical shock from damage to the power cord. · Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard. · Do not cover the slots or openings of the monitor for proper heat dissipation. Always put the monitor in a place where there is adequate ventilation. · Avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the area of the monitor. Place the monitor just below eye level. · Handle with care when transporting the monitor. · Refrain from giving the shock or scratch to the screen, as screen is fragile. CLEANING YOUR MONITOR No specific liquid or chemical necessary when cleaning this LCD monitor However, we suggest to clean the monitor with non-abrasive cloths and cleaning solutions used in hospitals to clean similar equipment. We recommend using 70% Isopropyl alcohol for the screen surface and warm water and a mild detergent for all other surfaces. Other acceptable cleaning agents are listed below: • 70% isopropyl alcohol • Cidex (2.4% glutaraldehyde solution) • 0.5% Chlorhexidine in 70% isopropyl alcohol To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away Form the monitor and spray cleaning solution onto a cloth. Without applying excessive pressure, clean the screen with the slightly dampened rag. Recomendation to Use more than One Unit As unforeseen situation can occationally occur for the monitor, when the display is used for safety control of human, equipments or unstable picture, or for emagencies, we strongly recommend you use more than one unit or prepare a spare unit. ENGLISH SAFETY PRECAUTION 10 User’s Guide POWER MANAGEMENT FUNCTION The monitor is equipped with the power management function which automatically reduce the power consumption when not in use in three power level modes. • Stand-by Mode The monitor goes into stand-by mode when the horizontal sync signal is off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the horizontal sync signal is restored. • Suspend Mode The monitor goes into suspend mode when the vertical sync signal is off for about 10 seconds. The power consumption during this is W. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical sync signal is restored. • Off Mode The monitor goes into power-off mode when the vertical and horizontal sync signals are off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the vertical and horizontal sync signals are restored. Power Management System The AMM190WTD Medical Monitor power management proposal. Provides four phases of power-saving modes by detecting the horizontal sync signal as shown in the table below. State Normal Operation DPMS Standby DPMS Suspend DPMS Off Horizontal Sync Active Inactive Active Inactive Vertical Sync Active Active Inactive Inactive Video Active Blanked Blanked Blanked Power Indicator Green Green Flashing (1 sec. Interval) Green Flashing (1 sec. Interval) Green Flashing (1 sec. Interval) Power Consumption 75W 27W 27W 27W When the monitor is power saving mode or detects an incorrect timing, the screen will be blank and power LED indicator will blink. AMM190WTD 11 ENGLISH PRESET MODES DVI and VGA input signal formats Resolution Horizontal frequency ( KHz ) Vertical frequency ( Hz ) Pixel clock ( MHz ) 640 x 350 @70Hz 31.469 70.087 25.175 640 x 480 @60Hz 31.469 59.940 25.175 640 x 480 @75Hz 37.500 75.000 31.500 640 x 480 @85Hz 43.269 85.008 36.000 800 x 600 @56Hz 35.156 56.250 36.000 800 x 600 @60Hz 37.879 60.317 40.000 800 x 600 @72Hz 48.077 72.188 50.000 800 x 600 @75Hz 46.875 75.000 49.500 800 x 600 @85Hz 53.674 85.061 56.250 1024 x 768 @60Hz 48.363 60.004 65.000 1024 x 768 @70Hz 56.476 70.069 75.000 1024 x 768 @75Hz 60.023 75.029 78.750 1024 x 768 @85Hz 68.677 84.997 94.500 1152 x 864 @60Hz 54.348 60.053 80.000 1152 x 864 @70Hz 63.955 70.016 94.200 1152 x 864 @75Hz 67.500 75.000 108.000 1280 x 960 @60Hz 60.000 60.000 108.000 1280 x 1024 @60Hz 63.974 60.013 108.500 1280 x 1024 @75Hz 79.976 75.025 135.000 1680 x 1050 @59.946Hz 64.742 59.946 119.125 1680 x 1050 @59.944Hz 65.160 59.944 147.000 1600 x 1200 @60Hz 74.077 59.981 130.375 12 User’s Guide Video Signals Component Format DVI VGA /SOG Video Y/C NTSC -M NTSC-443 PAL-BDGHI PAL-M PAL-N PAL-60 480/59.94i SDI 1/2 480/59.94p 576/50i Y/Pb /Pr RGB +CS RGB +HV 576/50p 720/50p 720/59.94p 720/60p 1035/59.94i 1035/60i 1080/23.98psf 1080/24psf 1080/23.98p 1080/24p 1080/25p 1080/29.97p 1080/30p 1080/50i 1080/59.94i 1080/60i 1080/50p O*1 1080/60p O*1 *1 Available for VGA. AMM190WTD 13 ENGLISH PIP / POP / PBP function The following combination options are available to you: VGA DVI SDI1 SDI2 C-Video Y-C Component / RGBs VGA DVI SDI1 SDI2 C-Video Y-C Component / RGBs Main SOG PIP SOG 14 User’s Guide DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC1 and DDC2B standard. INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. Use the supplied video cable (DVI, VGA, S-Video, C-Video) then connect to the host system accordingly. 2. Connect the DC power to the DC power connector on the monitor. 3. Connect one end of AC power cord into the AC Adapter and the other end to AC power outlet. 4. Then turn the host system on and then the monitor. 5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem. S - Video DVI VGA SDI IN IN OUT DC Power C - Video / SOG RGB / Component SDI OUT AMM190WTD 15 ENGLISH CONNECTING the POWER CORD * Check first to make sure that the power cord you use is the correct type required for your area. * This monitor has an universal AC adapter that allows operation in either AC 100 - 240 V ac voltage area. No user-adjustment is required. * Plug one end of the power cord to the AC adapter, plug another end to a proper AC outlet. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and marked HAR. For 120 volt Applications, use only UL Listed deachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. Hospital-grade power cord Extension power cord (optional) Model No: 1501047004 (5ft) or 1501047005 (15ft) or 1501047006 (75ft) Power Supply Model No: JMW1100KA1800F01 AMM190WTD 16 User’s Guide User Functions / Messages Key Name and Function Power LED : Lights up to indicate the power is turned ON. Power Switch : To power ON or OFF the monitor. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Right) parameter or moves rightward in OSD menu. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Left) parameter or moves leftward in OSD menu. PIP Switch : To enable or disable Picture In Picture function. PBP Switch : To enable or disable Picture By Picture function. POP Switch : To enable or disable Picture On Picture function. Adjust Switch : To activate or deactivate image adjustment in sub screen of PIP, PBP, POP mode. Locker Switch : To turn ON or OFF the system. How to access the menu 1. Push the “Knob” button to activate the OSD menu. 2. Able to turn left or right the button to select those icons. The icon will be highlighted when is selected. 3. Push the “knob” button to go into the another OSD menu. 4. Turn left or right “Knob” button to increase or decrease the number of selected function. 5. In order to exit from the OSD menu in a different layer, then choose the “Exit option”. In case of long pushing and holding the button around two or three seconds, then it will completely out from the menu regardless wherever you are. 6. Turn the “Knob” button in a fast way to the left or right, while the menu is not activated, then input signal menu will turns up with “V” mark which is chosen current available input signal. You can switch to another input signal source by turning the knob slowly then select the target source by pushing the knob. AMM190WTD 17 ENGLISH OSD Section Main Menu Chromatic Adjust Color Temp, Gamma Visual Adjust Brightness, Contrast, Phase, Chroma, Sharpness-H, Sharpness-V Setting Adjust Scale Mode, Color Space, Mirror, Freeze Frame, Zoom / Pan, PIP, POP, PBP Advanced Adjust OSD Position Control, Screen Control, DPMS, Auto Source Select, Smart Select, Restore Factory, Key Lock Information Adjust Custom Entry, SN, Run Time, Input Format Exit Exit the menu 18 User’s Guide OSD Section Chromatic Color Temp Change the color temperature - D65, D93, S1, S2 Gamma Change the gamma value - 1.8, 1.9, 1.95, 2.1, 2.1S, 2.2, 2.3, 2.4, 2.4S, S0, Radio graph Exit Exit the menu Visual Brightness Adjust the brightness of panel (Range 0 - 100) Contrast Adjust the contrast of video (Range 0 - 100) Phase Adjust the phase of video (Range 0 - 100) *available for C and S - video Chroma Adjust the chroma of video (Range 0 - 100) *available for C and S - video Sharpness-H Set the sharpness of horizontal image (Range 0 - 100) Sharpness-V Set the sharpness of vertical image (Range 0 - 100) Exit Exit the menu AMM190WTD 19 ENGLISH OSD Section Setting Scale Mode Change the scale mode - Fill all, One to One, Vertical - fill, Horizontal - fill, Fill aspect ratio Color Space Change color space between RGB and YPbPr *available for Component and RGBS Mirror Off / On mirror image Freeze Frame Off / On freeze frame Zoom / Pan Enable zoom - in and pan function PIP Enable PIP (Picture In Picture) function POP Enable POP (Picture On Picture) function PBP Enable PBP (Picture By Picture) function Exit Exit the menu 20 User’s Guide OSD Section Sub menu of PIP Mode PIP Mode ON / Off Source PIP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI, SOG Position PIP sub screen position - Top L, Top R, Bottom L, Bottom R Size PIP sub screen size - Small, Medium, Large Blending PIP sub screen blending (Range 0 - 100) Swap PIP sub screen swap Exit Exit the menu Sub menu of PBP Mode PBP Mode ON / Off Source PBP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI, SOG Swap PBP sub screen swap Exit Exit the menu AMM190WTD 21 ENGLISH OSD Section Sub menu of POP Mode POP Mode ON / Off Source POP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI, SOG Position POP sub screen position - Top L, Top R, Bottom L, Bottom R Size POP sub screen size - Small, Medium, Large, Full Blending POP sub screen blending (Range 0 - 100) Swap POP sub screen swap Exit Exit the menu 22 User’s Guide OSD Section Advanced OSD Position Change the OSD menu - Position, Background, Control OSD time out, Language Screen Control Control and adjust H and V position, Freqency, Phase Noise Reduction, Motion Offset DPMS Change the DPMS Auto Source Adjust Auto Source Select between on and off Select Smart Select Enable / Disable smart select sub menu Restore Factory Changes the all OSD value to factory outgoing status Key Lock Set to key lock mode Exit Exit the menu AMM190WTD 23 Sub menu of OSD Control H-position Adjust OSD H - position (Range 0 - 100) V-position Adjust OSD V - position (Range 0 - 100) Back ground Adjust transparency of OSD back ground (Range 0 - 100) OSD Time out Adjust OSD time out - 5s, 10s, 15s, 20s, 1m, 2m Language OSD language - English, Japanese, Chinese, Korean, French, German Exit Exit the menu Sub menu of Screen Control H-position Adjust screen H - position (Range 0 - 100) *available for VGA V-position Adjust screen V - position (Range 0 - 100) *available for VGA Frequency Adjust frequency (Range 0 - 100) *available for VGA Phase Adjust phase (Range 0 - 100) *available for VGA Noise Noise reduction (Range 0 - 100) Reduction *available for Component, C-Video and S-Video Motion Offset Motion offset (Range 0 - 15) *available for Component, C-Video and S-Video Exit Exit the menu ENGLISH OSD Section 24 User’s Guide OSD Section Information Custom Entry Change the user or monitor’s name SN Display the serial number Run Time Display the total run time Input Format Display the current input resolution and vertical frequency Exit Exit the menu AMM190WTD 25 Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. Problems Current Status Remedy No Picture LED ON · Using OSD, adjust brightness and contrast to maximum or reset to their default settings. LED OFF · Check the Locker switch and Power switch. · Check if AC power cord is properly connected to the AC adapter. LED Blinking · Check if video signal cable is properly connected at the back of monitor. · Check if the power to computer system is ON. Abnormal Picture Unstable Picture · Check if the specification of graphics adapter and monitor is in compliance which may be causing the input signal frequency mismatch. Display is missing, center shift, or too small or too large in display size · Using Auto Setup button, if still display abnormal picture then adjust CLOCK, CLOCK-PHASE, H-POSITION and VPOSITION with non-standard signals. · Using OSD, in case of missing full-screen image, please select other resolution in your Operating System (Windows 95/98, NT) or other vertical refresh timing. · Must wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal or powering OFF the monitor. ENGLISH TROUBLESHOOTING 26 User’s Guide SPECIFICATION Model LCD Panel Type Resolution Pixel Pitch Display Color Color Tone Response Time Face Finishing Viewing Angle Input Signal (Analog & Sync (Analog) Composite Sync (Analog) Y/C Sync (Analog) AMM190WTD 19 TFT LCD Panel Active Matrix 1680 x 1050 @ 60Hz 0.24mm 16.7M colors Up to 256 color tone <25ms Typ. Protective Filter with Anti-Reflected Hard Coated +/- 85°(Horizontal), +/- 85° (vertical) Digital) 2.5~5.0Vp-p separated sync Composite Video (NTSC/PAL) S-Video (NTSC/PAL) - 75 Ohm Input Impedance (Analog) Video Sync - 1k Ohm Digital 24-bit MSB RGB TMDS Dual Link Scanning Frequency Horizontal 31.47~79.98kHz Vertical 50~85Hz Display Size HxV 16.1 x 10.1 (409.5mm x 255.94mm) Brightness, Contrast Radtio, Gray Scales Brightness 230 cd/m2 (Typ.) Contrast Ratio 700:1 (Typ.) Signal Input Connector Video DVI, HD15, SD/HD-SDI 1 and 2 , Component Y/G, Pb/B, Pr/R, H/CS, VS, C-Video and S-Video Communication DB9 (RS232) Signal Output Connector (Loop Through) Video SD/HD-SDI, Component Y/G, Pb/B, Pr/R, H/CS, VS, C-Video and S-Video Operating/Storage Environment Operating Temperature 32° ~ 95°F (0° - 35°C) Storage Temperature -4° ~ 140°F (-20° - 60°C) Storage Humidity 10 ~ 85%RH (without condensation) VESA Mounting 100mm x 100mm Power Source Display Monitor AC-Adapter DC 18V 6.67A AC100~240V 50/60Hz, 1.4~0.6A Regulations Safety, EMI & Environmental UL 60601-1, EN60601-1, EN60601-1-2, FCC, CE, CCC, VCCI, ROHS, IP:X1 Compliance Dimension Free Mount 19.5(W) x 12.87(H) x 3.39(D) 495.4mm(W) x 326.9mm(H) x 86mm(D) Weight Free Mount Optional Module Base Stand Adjustable high, swivel and tilt base stand ** All contents are subject to change without notice. ENGLISH AMM190WTD 27 : Direct Current 51LJ Medical Equipment E215822 MEDICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601-1, AND CAN/CSA C22.2 NO. 601.1 : UL approval mark according to the safety standard for Medical equipment This monitor is intended for use in Health Care Facilities model AMM190WTD Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide. No user serviceable parts inside, ask qualified personnel when accessing inside. For disposal of waste product, follow the requirement of local code. Electrical input rating: Classification Type of protection against electric shock: Class I Equipment. Degree of protection against the ingress of water: IPX1 compliance. Mode of operation: Continuous This monitor has been tested to comply with IEC/EN 60601-1, IEC/EN60601-1-2 and is certified by UL to medical standard UL60601-1(UL/cUL Mark). Because many medical offices are located in residential areas, this monitor, in addition to the medical requirements, has also been tested and found to comply with the limits for FCC Class B computing devices in a typically configured system. It is the system integrator or configurer’s responsibility to test and ensure that the entire system complies with applicable EMC laws. Environmental conditions for transport and storage: Temperature range within -4° to 140° F (-20° to 60°C) Relative humidity range within 10% to 85% Atmospheric pressure range within 500 to 1060 hPa. 28 User’s Guide Electromagnetic Compatibility Like other electrical medical equipment, the AMM190WTD requires special precautions to ensure electromagnetic compatibility with other electrical medical devices. To ensure electromagnetic compatibility (EMC), the AMM190WTD must be installed and operated according to the EMC information provided in this manual. Note The AMM190WTD has been designed and tested to comply with IEC 606011-2:2001 requirements for EMC with other devices. Caution Portable and mobile RF communications equipment may affect the normal function of the AMM190WTD. Warning Do not use cables or accessories other than those provided with the AMM190WTD, as this may result in increased electromagnetic emissions or decreased immunity to such emissions. Warning If the AMM190WTD is used adjacent to or stacked with other equipment, observe and verify normal operation of the AMM190WTD in the configuration in which it will be used prior to using it in a surgical procedure. Consult the tables below for guidance in placing the AMM190WTD. Manufacturer’s declaration - electromagnetic emission The Model AMM190WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM190WTD should assure that it is used in such an environment. Emission test Compliance RF emissions CISPR 11 Group 1 RF emissions CISPR 11 Class B Harmonic emissions IEC61000-3-2 Class D Voltage Fluctuations IEC61000-3-3 Complies Electromagnetic environment - guidance The Model AMM190WTD uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment AMM190WTD is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes Manufacturer’s declaration - electromagnetic immunity The Model AMM190WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM190WTD should assure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic environment - guidance Electrostatic discharge (ESD) IEC61000-4-2 6 kV contact 8 kV air 6 kV contact 8 kV air Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%. Electrical fast transient /burst IEC61000-4-4 2 kV for power supply lines 1 kV for input / output lines 2 kV for power supply lines 1 kV for input / output lines Mains power quality should be that of a typical commercial or hospital environment. Surge IEC61000-4-5 1 kV differential mode 2 kV common mode 1 kV differential mode 2 kV common mode Mains power quality should be that of a typical commercial or hospital environment. Power frequency (50/60Hz) magnetic field IEC 61000-4-8 Voltage dips, short interruptions and voltage variations on power supply input lines IEC61000-4-11 3.0 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. 3.0 A/m <5% Ut (>95% dip in Ut) for 0.5 cycle <5% Ut (>95% dip in Ut) for 0.5 cycle 40% Ut (60% dip in Ut) for 5 cycles 40% Ut (60% dip in Ut) for 5 cycles 70% Ut (30% dip in Ut) for 25 cycles 70% Ut (30% dip in Ut) for 25 cycles <5% Ut (>95% dip in Ut) for 5 sec. <5% Ut (>95% dip in Ut) for 5 sec. Mains power quaility should be that of a typical commercial or hospital environment. If the user of the AMM213TD/ AMM240WTD image intensifier requires continued operation during power mains interruptions, it is recommended that the AMM213TD/ AMM240WTD image intensifier be powered from an uninterruptible power supply or a battery. Note: Ut is the A.C. mains voltage prior to application of the test level. Manufacturer’s declaration - electromagnetic immunity The Model AMM190WTD is intended for use in the electromagnetic environment specified below. The customer or the user of AMM190WTD should ensure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic environment - guidance Portable and mobile RF communications equipment should be used no closer to any part of the AMM213TD/ AMM240WTD, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended Separation Distance 0.15 MHz to 80 MHz Conducted RF IEC61000-4-6 3 Vrms 150 KHz to 80 MHz 3 Vrms 150 KHz to 80 MHz Radiated RF IEC 61000-4-3 3 V/m 80MHz to 2.5 GHz 3 V/m 80MHz to 2.5 GHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz where P is the maximum oputput power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as deter-mined by an electromagnetic site survey (a), should be less than the compliance level in each frequency range (b).Interferency may occur in the vicinity of equipment marked with the follwing symbol: NOTE 1: At 80MHz and 800MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. (a) Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast, connot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the AMM190WTD is used exceeds the applicable RF compliance level above, the AMM190WTD should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the AMM190WTD. (b) Over the frequency range 150kHz to 80MHz, field strengths should be less than [V1] V/m. ENGLISH AMM190WTD 29 30 User’s Guide Recommended Separation Distances Between Portable and Mobile RF Communications Equipement and the AMM190WTD System The AMM190WTD system is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The user of the AMM190WTD system can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the AMM190WTD system as recommended below, according to the maximum output power of the communications equipment. Separation distance (m) according to frequency of transmitter Rated maximum output power (W) of transmitter 150kHz to 80MHz d=1.17, p 80MHz to 800MHz d=1.17, p 800MHz to 2.5GHz d=2.33, p 0.01 0.12 0.12 0.23 0.1 0.37 0.37 0.74 1.17 1.17 2.33 10 3.70 3.70 7.37 100 11.70 11.70 23.30 For transmitters rated at a maximum output power not listed above, the recommended separation distance (d) in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. AMM190WTD 31 ENGLISH Dimension Drawing (mm) of AMM190WTD REAR VIEW 32 User’s Guide Connectors DC Input Connector Jack Power Input Pin Description Pin Description GND NC GND VCC_24V VCC_24V Video Input 24 pin DVI-I connector. DDWG or equivalent connector. Pin Description Pin Description Pin Description T.M.D.S. Data2- 11 T.M.D.S. Data1 Shield 21 NC T.M.D.S. Data2+ 12 NC 22 T.M.D.S. Clock Shield T.M.D.S. Data2 Shield 13 NC 23 T.M.D.S. Clock+ NC 14 +5V Power 24 T.M.D.S. Clock- NC 15 Ground (for +5V) 25 Analog Red DDC Clock 16 Hot Plug Detect 26 Analog Green DDC Data 17 T.M.D.S. Data0- 27 Analog Blue Analog V - Sync 18 T.M.D.S. Data0+ 28 Analog H - Sync 29 GND(for analog signal) T.M.D.S. Data1- 19 T.M.D.S. Data0 Shield 10 T.M.D.S. Data1+ 20 NC 15 pin VGA connector. Pin Description Pin Description Pin Description GRED GND 11 NC GGREEN GND 12 GSDA GBLUE GND 13 IHS GND G5V 14 IVS GND 10 GND 15 GSCL S - Video connector. Pin Description Pin Description GND CHROMA GND LUMA C - Video connector. Pin Description DATA IN / OUT Description of Warranty Advan warrants that the goods sold hereunder will be free of defects in materials and workmanship, and such goods will substantially conform to the specifications furnished by Advan, and to any drawings or specifications furnished to Advan by the Buyer if approved by Advan. This warranty shall be effective only if Advan receives notice of such defect or nonconformance during the period of the warranty. In the event of warranty claim with EOL (End of Life) product(s), Advan has the exclusive right to replace with refurbished units or with an equivalent product. Commencement and Duration of Warranty The warranty period begins on the date of shipment from Advan. The goods sold hereunder are warranted for a period of 18 months from date of shipment unless otherwise agreed to by Buyer and Advan. No extension of the warranty will be given during the time the goods are in Advan possession. Place of Repair or Replacement In order to obtain service under this warranty, Buyer must notify Advan of the defect before expiration on the warranty period, and request a “Return Material Authorization Number.” If the configuration has been modified in any manner, the product must be returned to its original configuration before any warranty service will be perfomed by Advan. No goods are to be returned to Advan without prior authorization. Buyer will be responsible for packaging and shipping the defective goods to the Advan Service Facility with shipping charges prepaid. Limitation of Warranty Monitor: For 18 months after the date of purchase, ADVAN or its Authorized Service Centers, will repair or replace if defective in material or workmanship. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or improper installation or operation, any damage caused from service, maintenance, modifications or tampering by anyone other than an ADVAN Authorized Service Representative, or by the use of supplies, consumable items and conditions beyond the control of ADVAN, such as common carrier provided equipment and/or facilities, operation of ADVAN product in excess of the specifications or with the Serial Number or Rating label removed. ENGLISH AMM190WTD 33 34 User’s Guide ADVAN DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED. No oral or written information or advice given by ADVAN, its authorized service center, distributors, dealers, agents or employees, shall create another warranty or modify this warranty. This warranty states ADVAN’s entire liability and your exclusive remedy against ADVAN for any failure of the ADVAN’s product to operate properly. Neither ADVAN nor anyone else involved in the development, production, or delivery of this product shall be liable for any indirect, incidental, special consequential, exemplary, or punitive damages, including lost profits, arising from the use of or inability to consequential or incidental damages. This Limited Warranty gives you special legal rights and you may also have other right, which vary from State to State. Installation Advan makes no warranty with respect to any installation of Advan’s product(s) by Advan, any authorized dealer, or any other person. Technical Assistance For technical assistance please call (510)490-1005 between 8:00 a.m. and 5:00 p.m. PST, Monday through Friday or email to support@advancorp.com with a description of your technical issues. Service If your Medical Monitor needs service, call Advan Customer Service / RMA at (510)490-1005 between 7:00 a.m and 4:00 p.m PST, Monday through Friday or fax to (510)490-1151. You will need the unit’s serial number and a brief description of the problem and where unit were purchased to receive a RMA number. If a service is required please return the product for service using the original shipping container with the RMA number included in package on the outside of the box. In order to protect ADVAN employees form potential health hazards, ADVAN requires that the RMA product be disinfected before returning to ADVAN for service. Any product not cleaned prior to shipment will be returned to the customer. Note: Returns will not be accepted without an assigned RMA number. In-transit damage is not covered by warranty. We suggest you always insure your shipment. Advan will only pay for the return shipment by surface transportation. It is the responsibility of the sender to prepay transportation charges. ENGLISH AMM190WTD 35 ADVAN INT’L CORP 47817 Fremont Blvd. Fremont, CA 94538, USA Tel : 510-490-1005 Fax : 510-490-1151 Web Page : http://www.advancorp.com ADVAN Korea 150-871 서울시 영등포구 여의도동 14-24 삼보호정빌딩 2층 210호 Tel : 02.783.5197 Fax : 02.783.5196
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : ericlau Create Date : 2009:11:18 18:31:02-08:00 Modify Date : 2009:12:11 15:02:15+09:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2 Metadata Date : 2009:12:11 15:02:15+09:00 Format : application/pdf Title : AMM190WTD RevA1 111809.indd Creator : ericlau Document ID : uuid:e97d2df4-7532-4d01-9540-9130b8a330bc Instance ID : uuid:20e198d5-e3d7-48fe-85f4-a950c7a5c317 Page Count : 38EXIF Metadata provided by EXIF.tools