BIG KING HORN SPEAKER ENT ROC4TX TRANSMITTER User Manual

BIG KING HORN SPEAKER ENT. CO., LTD. TRANSMITTER

User Manual

Arming: Press & Release the “Lock” buttonSilent Arming: Press & Release the “3rd” button Twice in 3 sec.Disarming: Press & Release the “Unlock” buttonSilent Disarming: Press & Release the “3rd” button Twice in 3 secPage 1Remote Control Quick Reference Guide2 X2 X THE SIREN WILLCHIRP ONCE THE PARKING LIGHTSWILL FLASH ONCETHE DOORS WILL LOCK(IF CONNECTED) THE PARKING LIGHTSWILL FLASH ONCETHE DOORS WILL LOCK(IF CONNECTED)THE SIREN WILLCHIRP TWICE THE PARKING LIGHTSWILL FLASH TWICETHE DOORS WILL UNLOCK(IF CONNECTED)THE PARKING LIGHTSWILL FLASH TWICETHE DOORS WILL UNLOCK(IF CONNECTED)Table Of ContentsOwner’s GuideArming the System ....................... 3Disarming the System ................. 4Emergency Override .................... 4System Armed & Activated ........... 5Panic ............................................ 5Sensor By-Pass ............................ 5Auxiliary Channel ......................... 63rd Channel .................................. 6Remote Controlled Anti-Carjack ... 6Anti-Carjacking ............................. 7Valet Mode ................................... 8LED Status Indicator .................... 8Auxiliary Sensor & Prewarn .......... 9Installation InstructionsHow To Program Remote Control ............. 9How To Program Features ...................... 10Programmable Features .................. 10 - 12Wiring Diagram ....................................... 13Door Lock/Unlocking Systems ................ 14 IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no changeto the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
To Activate the Auxiliary Channel: Press & Hold The “3rd” Button for 3 SecondsTo Activate the 3rd Channel: Press & Hold The “4th” Button for 3 SecondsTo Activate Remote Anti-Carjack: (programmable feature # 10)Press & Hold the “4th” button, for 3 Secs, with the ignition “On”Emergency Override:Panic: Press & Hold the “Lock” Button for 3 Sec’s, with the ignition “Off”Shock Sensor & Prewarn Bypass:1) Arm the alarm by, Pressing & Releasing the “Lock” button2) Within 2 seconds Press & Release the “3rd” button.Page 2Then1.2.Operate Remote Start UnitOperate Window Roll-Up Unit Hold 3 secondsOpen Electric TrunkOperate Window Roll-Up UnitOperate Remote Start Unit THEN WITHIN 10 SECONDS PRESS & RELEASEVALET BUTTON Hold 3 secondsTHE SIREN WILL SOUND THE PARKING LIGHTSWILL FLASH Hold 3 seconds Hold 3 seconds
The system may be "Armed" by any of 3 methods:1) Remote Control Arming: Press & Release the “Lock” buttonPage 3Arming the AlarmUpon Arming: • The siren will chirp one time. (3 times if there is open zone)• The parking lights will flash once.• The doors will lock. (If an optional interface is connected)• The starter interrupt will engage.• The LED Status Indicator will begin to flash slowly.- If a zone is open, (for example a car door), when arming, the alarm will still arm,but will bypass the open zone until the zone is secured (siren will chirp 3 times).3) To Passively Arm: Turn Ignition “Off”, Then Close all Doors.Automatic “Last Door Arming” is a programmable feature which allows the alarmto arm itself and, if desired, lock the doors upon arming.If on, anytime the ignition is turned off, and then a door is opened and closed:• The Siren will chirp once to confirm arming countdown has begun.• The LED Status Indicator will begin to flash rapidly.Thirty seconds later:• The siren will chirp & the lights will flash once.• The LED Status Indicator will begin to flash slowly.• The starter interrupt will engage.- The alarm is now fully armed. The doors will lock at this time, if programmed todo so, and if the vehicle is equipped.- The system can not Last Door Arm if a protected zone is open. Should a ve-hicle door be opened during the arming countdown, the countdown will stop andstart over again when the door is closed.AUTO REARM (programmable) allows the Alarm to Rearm itself, if it is Disarmed.2) SILENT Remote Control Arming: Press & Release the “3rd” button Twice within 3 seconds THE SIREN WILLCHIRP ONCE THE PARKING LIGHTSWILL FLASH ONCETHE DOORS WILL LOCK(IF CONNECTED) THE PARKING LIGHTSWILL FLASH ONCETHE DOORS WILL LOCK(IF CONNECTED)2 X
The system may be "Disarmed" by any of 3 methods:1) Remote Control Disarming: Press & Release the “Unlock” button2) SILENT Remote Control Disarming: Press & Release the “3rd” button Twice within 3 secUpon Disarm: • The siren will chirp twice. (4 chirps if alarm has activated & reset)• The parking lights will flash twice. (4 times if alarm has activated)• The doors will unlock. (If an optional interface is connected)• The starter interrupt will disengage.• The LED Status Indicator begins flashing rapidly for Automatic Rearming, until alarm Rearms or a vehicle door is opened.2-STAGE DISARM: If Disarming the alarm while it is triggered (siren sounding), thefirst press of any remote control button will only silence the siren/horn. A secondpress of the “Unlock” button will Disarm the alarm. IMMOBILIZER MODE: If this mode is programmed “On”, the starter interrupt will remain engaged after the alarm is Disarmed, until the ignition is turned “On” and youPress & Release the Valet button. (Refer to programmable feature # 5) To Start Vehicle: . 1. Disarm the alarm, then Turn “On” the vehicle’s ignition 2. Press & Release the Valet Button. Step 1: With the system in the armed condition, enter the vehicle via the driver'sdoor (be aware that the alarm will trigger when the door is opened). Step 2: Using your key, turn the vehicle’s ignition to the "On" position. Step 3: Within 10 seconds, Press & Release the Valet/ Override Switch.Page 4Disarming the AlarmEmergency Override THEN WITHIN 10 SECONDSTHE PARKING LIGHTSWILL FLASH TWICETHE DOORS WILL UNLOCK(IF CONNECTED)THE SIREN WILLCHIRP TWICE THE PARKING LIGHTSWILL FLASH TWICETHE DOORS WILL UNLOCK(IF CONNECTED)2 X
Regardless of method used to Arm the alarm, once Armed, the alarm will monitorall protected zones, and if an intrusion attempt is detected it will activate, or“trigger”.A trigger consists of the following:• The electronic siren, or optionally the vehicle’s horn, will start sounding.• The exterior parking lights will flash on and off repeatedly.An activation has a 30 second duration unless the system is disarmed using theremote control or the Valet /Override switch. If all protected zones are secure atthe end of the trigger, the system will stop and rearm itself to detect further entryattempts. If a protected zone is still open at the end of the trigger cycle, the alarmwill continue to re-trigger itself for up to six activated cycles before it resets itselfand ignores the violated zone.Should it be needed in a threatening situation, or you feel the need to attractattention, the alarm can be triggered using the remote control. Your alarm fea-tures “Panic Mode”, which allows you to activate “Panic” from the “Arm/Lock”button.To Activate Remote Panic: Press & Hold the “Arm/Lock” Button,for 3 seconds, with the ignition “Off”.The shock sensor & Prewarn zone can be by-passed using the remotecontrol. This may be useful in stormy weather.1) Arm the alarm by, Pressing & Releasing the “Lock” button.2) Within 2 seconds, Press & Release the “3rd” button.- The siren will chirp once to confirm sensor has been by-passed.- Upon Disarming the alarm, the sensor zone will reset.Sensor By-passSystem Armed & ActivatedRemote Panic OperationPage 5Then 2.THE SIREN WILL SOUNDTHE PARKING LIGHTSWILL FLASH Hold 3 seconds1.
The Auxiliary Channel may be used to operate an optional function. Possibili-ties include remote trunk release, remote car starting, or an on-demand re-mote window roll-up interface. Please see your Omega dealer for details onavailable options.To Activate the Auxiliary Channel:Press & Hold the “3rd” Button for 3 Seconds.- The alarm will Disarm upon activating the Auxiliary channel.- The Auxiliary Channel cannot be activated if the vehicle's ignition is "On".The programmable 3rd Channel may be used to operate an optional function,such as a remote start unit or an on-demand remote window roll-up interface.Please see your Omega dealer for details on available options.To Activate the 3rd Channel:Press & Hold the “4th” button for 3 Seconds.- The 3rd Channel can be programmed to Supply a (-) output when the alarmis Armed to operate a Window Roll-Up module (Programmable feature # 12).The Anti-Carjacking mode can be activated using the remote control.- Refer to next page for sequence details. (programmable feature # 10)To Activate Remote Anti-Carjack:Press & Hold The “4th” Button, For 3 Seconds, With The Ignition “On”.Page 6The Auxiliary ChannelRemote Anti-CarjackThe 3rd Channel Auxiliary Output Hold 3 seconds Hold 3 seconds Opperate Remote Start UnitOpperate Window Roll-Up Unit Hold 3 secondsOpen Electric TrunkOpperate Window Roll-Up UnitOpperate Remote Start Unit
Page 7The Anti-Carjacking sequence may be activated by any of 3 methods:1) Using the remote control, by holding down the Small “4th” Button for 3 seconds while the ignition is “On”. (programmable feature # 10)2) When a door is Opened while the ignition is “On” (programmable feature # 10)3) Every time the ignition is turned “On”. (Programmable feature # 9)1) Anti-Carjacking activated using the transmitter: (programmable feature #10)The Anti Car-Jacking operation may be activated by pressing and holding theremote control’s Small “4th” button for 3 seconds while the ignition is “On”.2) Anti-Carjacking activated by an Open door: (programmable feature #10)If programmable feature #10 is “On”, the system will initiate the Anti-Carjackingsequence every time a vehicle door is opened while the ignition is “On”.3) Anti-Carjacking activated by the ignition: (programmable feature #9)If programmable feature #9 is “On”, the system will initiate the Anti-Carjackingsequence every time the vehicle’s ignition is turned “On”.IMMOBILIZER MODE: If the “Immobilizer mode” is programmed “On”, theignition activated anti-carjacking sequence will be cancelled and the “Immobilizermode” disarmed by: first turning “On” the vehicle’s ignition, then Pressing &Releasing the valet button. (Refer to programmable feature # 5)Once the Anti-Carjacking sequence has begun, the user has 59 seconds topress the Valet/Override Switch in order to cancel the sequence.ORDER OF ANTI-CARJACKING SEQUENCE:- For first 20 seconds after the sequence has begun there are no signs.- From 21-30 seconds, the LED will blink slowly.- From 31-45 seconds, the LED will blink fast and the siren/horn will chirp once every 2 seconds.- From 46-60 seconds, the LED will blink fast and the siren/horn will chirp once per second.- If not cancelled yet, at 61 seconds the alarm will trigger.In the triggered condition:- The siren/horn will sound & The parking lights will flash.- The starter interrupt will engage.NOTE: Once the Anti-Carjack mode is triggered, the remote control will NOTstop the operation, nor will the system reset automatically. Once it is trig-gered, the Anti-Carjacking operation can only be deactivated by:1) Turning the vehicle’s ignition “Off”.2) Turning the vehicle’s ignition back “On”.3) Within 10 seconds, Press & Release the Valet button.Programmable Anti-Carjacking Protection
Page 8Valet ModeValet Mode can only be entered into while the alarm is Disarmed.Valet Mode turns off all of the alarm’s security features, (including Anti-Carjack).Valet Mode is designed for situations in which it is not convenient for the securityportion of the alarm to be operational; for example during extended stopovers forvehicle servicing, loaning others your vehicle, maintenance, valet parking,washing, etc. The convenience features such as keyless entry will still operate.To Enter Valet Mode (Alarm MUST be Disarmed):Press & Hold the Valet Switch for 3 Seconds. - The LED Status Indicator will light solid Blue & the siren will emit a long chirp to confirm entry into Valet Mode. Now the system cannot become Armed.- The vehicle's ignition may be "On" or "Off" when entering Valet Mode.- To remind you its in Valet Mode ,The siren will chirp every time the vehicle’s ignition is turned “Off”To Exit Valet Mode:Simply Press & Release the Valet Switch. - The LED will turn off and the siren will emit a long chirp to confirm that thesystem has exited Valet Mode. Normal arming operations may be resumed.- The vehicle's ignition may be "On" or "Off" when exiting Valet Mode.The Blue LED Status Indicator visually shows the status of the alarm and alsoprovides a high level of visual deterrence. The Blue LED Status Indicator Light isnormally mounted where it can be seen by the driver, as well as from outside.Security System Status: The primary function of the Blue LED Status IndicatorLight is to indicate the normal operating status of the security system: Off = The system is disarmed and not performing any automatic functions. On Constant = The system is in the Valet Mode. Flashing Slow = The system is fully Armed. Flashing Fast (while Disarmed) = Last Door Arming or Automatic Rearming. Zone Violation: Once alarm is Disarmed, LED will show which zone triggeredalarm until the ignition is turned “On” (this clears unit’s memory).2 flash & pause = Pin-Switch zone triggered alarm.3 flash & pause = Door zone triggered alarm.4 flash & pause = Sensor zone triggered alarm.Automatic Transmitter Verification: For the first 10 seconds after the vehicle’signition is turned "On", the LED Status Indicator will flash a number of times equalto the number of remote control transmitters which are programmed to operatethe alarm. This indication can be from 1 Flash /pause up to 4 Flashes /pause, asthe system can be operated by just one, or as many as 4 remote transmitters.The LED Status Indicator
Page 9Auxiliary Sensor: This security system is equipped with a plug-in port for anoptional sensor to increase the effectiveness of the system. The comprehensiveline of optional sensors offered is comprised of impact sensors, glass tamperingsensors, and microwave/radar sensors which can detect motion inside andoutside the vehicle.Prewarning Detection: This circuit requires connection to a dual zone sensoror detection device. When the sensor’s prewarn zone is triggered the siren willemit a series of chirps.To program remote controls to operate the alarm:Step 1: Turn "On" the vehicle's ignition.Step 2: Within 7 seconds press the Valet/Override Switch 5 times. The alarmwill wolf the siren once to confirm entry into Remote Control Programming Mode.Step 3: Within 10 seconds, press any Button on each remote to be programmed.The siren will chirp to confirm each time a remote has been programed.If 10 seconds expire without any programming activity, or if the vehicle’s ignitionis turned “Off”, the system will automatically exit Remote Control ProgrammingMode. The siren will emit 2 long chirps to confirm exit.NOTE: Up to 4 remote controls can be programed to operate the alarm. When-ever a remote control, new or existing, is programmed to the alarm, all existingcodes are erased for security. So all remote controls which are to operate thealarm, must be programmed in at the same time.Immobilizer Mode: Immobilizer mode must be disarmed before enteringremote control programming mode. (refer to programmable feature # 5)1. Turn “On” ignition2. Press & Release the Valet/Override button, (siren will chirp twice)3. Press valet/override button 5 times to enter remote control programmingmode.ATV: The LED Status Indicator will show the number of programmed remotecontrol transmitters for 10 seconds after the vehicle’s ignition is turned On. As the instructions above show, programming extra transmitters to any vehiclesecurity system is easy; the exclusive patented ATV feature protects againstsomeone programming their own transmitter to operate your system.Auxiliary Sensor & PrewarningHow to Program Remote Controls to the Alarm
Page 10To access Features Programming Mode:Step 1: Turn the vehicle's ignition "On" then "Off".Step 2: Within 7 seconds of turning the ignition "Off", press the Valet Switch 5times. The siren will wolf once confirming entry to Features Programming Mode.Step 3: Within 10 seconds of entering Features Programming Mode, press theValet Switch the number of times equal to the number of the feature to beprogrammed. The siren will repeat the feature number with chirps to confirm.Step 4: After the system acknowledges the feature to be programmed:- press the “Lock” button on the remote to turn the feature “ON” (the siren willchirp once), or,- press the “Unlock” Button to turn feature “OFF” (siren will chirp twice).Note: Once the feature to be programed is selected, you can toggle thefeature between its settings by pressing the “Lock” & “Unlock” buttons onthe remote control.- To program more features, simply repeat Steps 3 and 4.- If 10 seconds expire without any programming activity, or if the vehicle’s igni-tion is turned “On”, the alarm will automatically exit Features ProgrammingMode. The siren will confirm exit.The alarm has 15 programmable features which allow it to be customized to suitemany individual needs. The following pages provide a brief explanation for eachfeature, and notes its factory default setting.• = Default Factory Setting1. Auto-Rearm: ( •On = 1 siren chirp / Off = 2 chirps)- Allows the Alarm to Rearm itself, if it is Disarmed.2. Last Door Arming: (•On = 1 siren chirp / Off =2 chirps)- Configures the alarm to automatically arm itself 30 seconds after the lastdoor is closed with the ignition “Off”.3. Doors Lock w/ Last Door Arming: (•On = 1 siren chirp /Off = 2 chirps)- Adds the automatic locking of the vehicle's doors to the previous feature.How to Program FeaturesProgrammable Features
Page 114. Double Pulse Unlock: ( 2 pulses = 1 siren chirp / • 1 pulse = 2 chirps)- Sets alarm to give 2 unlock pulses upon Disarm for cars that require it.5. Immobilizer Mode: ( On = 1 siren chirp / •Off = 2 chirps)- If this mode is programmed “On”, the starter interrupt will remain engaged afterthe alarm is Disarmed, until the vehicle’s ignition is turned “On” and you Press &Release the Valet button.- Anti-Carjack: Upon disarming the “Immobilizer mode”, ignition activated anti-carjacking will be automatically cancelled, (if programmed “On”).- Remote Control Programming Mode: Immobilizer mode must be disarmedbefore entering remote control programming mode.6. Siren & Horn or Horn: ( •Siren & Horn = 1 siren chirp / Horn = 2 chirps)- This feature configures the alarm’s Brown/White Horn-Honk output wire. Thiswire can be configured to honk the horn in addition to the Brown wire operatingthe siren, or take over all of the Siren’s functions SO THAT NO SIREN ISNECESSARY.- If Siren & Horn are selected: The horn will honk in addition to siren soundingonly when the door, pin-switch, or ignition zones are violated. (The horn will nothonk if alarm is triggered by the sensor zone, or during confirmation “chirps”)- If Only Horn is selected: The car horn will replace the siren and perform allof its functions. NOTE: Brown Siren wire will still be fully active & operational.7. Shock Sensor False-Alarm Bypass: (On = 1 siren chirp / •Off = 2 chirps)- This feature will temporarily turn “Off” the shock sensor & pre-warn zone if:a. The pre-warn is triggered 10 times while the alarm is Armed.b. The instant trigger zone is triggered 5 times while the alarm is Armed.- The by-passed zones will be reinstated the next time the alarm is Armed.8. Dome-Light Delay Bypass: (On = 1 siren chirp / •Off = 2 chirps)- This feature will turn “Off” the 3-chirp open zone warning when Arming thealarm with the remote control. This is for use in vehicles that keep the dome-lightilluminated after the doors have been closed.9. Ignition Activated Anti-Carjacking: (On = 1 siren chirp / •Off = 2 chirps)- This feature turns the alarm’s Ignition Anti-Carjacking feature “On” or “Off”.10. Remote & Door Activated Anti-Carjacking: (On = 1 chirp / •Off = 2 chirps)- This feature turns both the alarm’s Remote Control and Open Door activatedAnti-Carjacking features “On” or “Off”.
Page 1211. Dome-Light or Window Roll-Up: (•Dome-Light = 1 siren chirp / WindowRoll-UP = 2 chirps)- Configures the alarm’s “Black/White” wire to operate the:a. Dome-Light: Supply a (-) output when the alarm is Disarmed to illuminate thevehicle’s Dome-Light for 30 seconds through the use of a relay, orb. Window Roll-Up or accessory: Supply a (-) output for 30 seconds when thealarm is Armed to operate a Window Roll-Up module or other accessory.12. 3rd Channel Output: (•Momentary = 1 siren chirp / Window Roll-UP =2 chirps)- Configures the alarm’s “Pink” wire to operate an:a. Accessory : Supply a (-) output as long as the small “4th” button on the remotecontrol, is pressed & held while the vehicle’s ignition is “Off”, (max 30 seconds).b. Window Roll-Up or accessory: Supply a (-) output for 30 seconds when thealarm is Armed to operate a Window Roll-Up module or other accessory.13. Ignition Door Lock/Unlock: (•On = 1 siren chirp / Off = 2 chirps)- Configures the alarm to Lock the vehicle's doors when the ignition is turned “On” and Unlock the vehicle’s doors when the ignition is turned “Off”.14. “RFID” Add-On to Anti-Hijacking: (On = 1 siren chirp / •Off = 2 chirps)- Adds an “RFID” layer to both the Ignition & Open Door activated Anti-Hijackingfeatures. (Note: Special RFID remote control required)JUMPER ON SIDE OF ALARM BRAIN:Lock Pulse Time: ( • .80 seconds = Jumper “In” / 4 seconds = Jumper “Out”)- Determines the length of the alarm’s door lock/unlock pulse output.0.80Sec4.0Sec-Press hold TX' button 5 seconds,LED will flash,TX'RFID is turned "On".-Press hold TX' button 5 seconds,LED will solid,TX'RFID is turned "Off".
Brown/White :This wire can be configured (Programmable feature # 6), to honk the hornin addition to the Brown wire operating the siren, or take over all of the Siren’s functions SO THAT NO SIREN IS NECESSARYCafé/con lista Blanca:Este cable se puede programar (función #6), a sonar el claxon en conjunto al cable Café operar la Sirena, O TOMAR TODAS LA FUNCIONES DE LASIRENA PARAQUE NO HAGA FALTA INSTALAR SIRENA.Brown/White - Café/Blanco = (-Horn Output, Salida claxon -)Black/White - Negro/Blanco = (-Dome-Light , Salida luz de cabina-)Grey - Gris = (-Auxiliary output, Segundo canal auxiliar-)Pink - Rosado = (-3rd channel output, Tercer canal-)Orange - Naranja = (-Starter Kill, Corte -)Blue - Azul = (-Trigger Input, Disparo -)Violet - Violeta = (+Door Input, Puerta +)Green - Verde = (-Door Input, Puerta -)Yellow - Amarillo = (+Accessory, Ignición +)Brown - Café = (+Siren/Horn, +Sirena/Claxon)Red - Rojo = (+12 Volts, +12 Voltios)White - Blanco = (+Flashing Lights, +Luces)Black - Negro = (-Ground, -Tierra)Valet/Override Button0.80Sec4.0SecDoor Lock Pulse Time JumperLED Status IndicatorOptionalSensorK9 SSGreen - Verde = (-Lock, -Cierre)Red - Rojo = (+12 Volts)Blue - Azul = (- Unlock, - Apertura)Siren Pin-Switch (-) Pin-Switch (-)Battery Pin-Switch (+)15 Amp+ Parking Lights / LucesRelayTrunkReleaseRelayRelay Car Horn /ClaxonDome-Light(-)AuxiliaryOutputPage 13
Page 14Negative Trigger System / Sistema Negativo:Doorlock SwitchGroundVehicle's DoorlockRelay Control UnitLockUnlock Lock wire /Cable de cierreUnlock wire/ Cable de Apertura+DoorlockActuators5 Wire Reversal (Rest at ground): Cambio de Polaridad:Positive Trigger System / Sistema Positivo:Doorlock Switch(+) 12 VoltsVehicle's DoorlockRelay Control UnitLockUnlock Lock wire /Cable de cierreUnlock wire/ Cable de Apertura+DoorlockActuators(+)12 VoltsUnlock UnlockPassengerDoorlock SwitchDriverDoorlockSwitch - Lock wire "Switch" side. -cable de Cierre, lado del switch -Lock wire "Motor" side. -cable de Cierre, lado MotorCut both Lock andUnlock wires in car- Unlock wire "Switch" side. -cable de Apertura, lado del switchLock Lock- Ground- Unlock wire "Motor" side. -cable de Apertura, lado MotorGreenBlueFuse308787a308787aGreenBlueLock Relay Unlock RelayFuse308787a308787aGreenBlueLock Relay Unlock Relay(+)12 VoltsDoor Locking Systems / Sistemas De Cierre
Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu