BITWAVE AMP Bluetooth headset User Manual 2016 Amp All Language User Guide Front ai

Download:
Mirror Download [FCC.gov]
Document ID	2917033
Application ID	EeiBQHeBycUjaHqrLB0+Pw==
Document Description	15_AMP UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	63.68kB (795995 bits)
Date Submitted	2016-03-02 00:00:00
Date Available	2016-03-02 00:00:00
Creation Date	2016-02-25 15:55:35
Producing Software	Acrobat Distiller 10.1.14 (Windows)
Document Lastmod	2016-02-25 15:55:35
Document Title	2016 Amp All Language User Guide Front.ai
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Rod

AMP SERIES USER GUIDE
FOR A DIGITAL COPY OF THIS USER GUIDE LAUNCH CLEARLINK APP OR
VISIT WWW.UCLEAR-DIGITAL.COM
MOUNTING (PERMANENT MOUNT)
MOUNTING (TEMPORARY MOUNT)
1) Locate and clean a position on the
left side of helmet close to lower
edge of the helmet.
1) Position and fasten the clip
bracket onto the helmet.
TOP
2) Peel off the 3M double sided tape
protective film and place the mount
with logo on bottom and place Mount
to the position in step 1.
3) Apply pressure to the metal bracket
to ensure that the bracket is firmly
secured. Note: It takes 24hours for
adhesive to set.
2) Remove the metal handles
after clip bracket has been
installed.
3) Use additional
anti-slip rubber
patch provided
if required.
INSTALL CONTROL UNIT
REMOVE CONTROL UNIT
1) From the top, slide AMP unit onto the
bracket. You should hear a ‘click’ sound
when fully inserted.
1) Remove USB speaker connector.
2) Slide AMP upward to release from
2) Fully insert the speaker USB connector.
PULSE PRO & BOOST PRO PLACEMENT
FIG.A
SPEAKER
TOWARDS EAR
5.5”
SPEAKER
TOWARDS EAR
3/16”
MIC PORT
FACE FORWARD
MIC MINIMUM PLACEMENT
BOOST PLUS PLACEMENT
MICROPHONE
FACE FORWARD
Both mics should be placed parallel to each other
SPEAKER USB PLUG
SEE FIG.A
Insert the speaker USB
wire into the control
unit until you can no
longer see the 3 ribs on
the USB speaker wire plug.
OR
TECHNICAL DATA
BUTTONS
POWER ON
Press & Hold “Power”
for 2 seconds
POWER OFF
VOLUME UP
VOLUME DOWN
Press & Hold “Power”
for 5 seconds
Press & Release “Up”
once per level
Press & Release “Down”
once per level
Battery: 3.7V, 500mAh Lithium-ion
Talk Time: Up to 10 Hours
Stand by Time: 400 Hours
Operating Temp: -30C(-4F) to 60C(140F)
Required Charging Temp: 0°C(32F) to 45°C(+113 F°)
Controller Unit Size: 60 x 40 x 18mm(2.9 x 1.75 x 1")
ClearLink: Android 4.4 or Later. Apple iOS 8 or Later
BUTTON CONFIGURATION REFERENCE
BASIC COMMANDS
Power On
Hold Press “Power” once for 2 seconds
Power Off
Hold “Power” for 5 seconds
Activate Bluetooth Pairing
Hold “Up” and “Down” for 2 seconds
Volume Up
Press “Up” once per volume level
Volume Down
Press “Down” once per volume level
Reset
Press “Power”, “Up” and “Down” once simultaneously
ANSWER INCOMING CALL
Say “Hello”or
Press “Power” once
1) Power on the unit. 2) Turn on the phone’s
Hold “Up” and
Bluetooth, search
“Down”2 seconds
Bluetooth device list
until LED alternately and select/connect
blinks blue and red. your AMP model.
3) After successful Pairing power off Unit to
store Phone into Memory. When AMP Pro,
AMP Plus or Amp is powered on, it will auto
connect to the phone.
REJECT OR END CALL
Hold “Power”
2 Seconds
REDIAL LAST NUMBER
Hold “Power” and
“Up” 2 seconds
VOICE DIAL
Hold “Power” and
“Down” 2 seconds
MUSIC PLAYBACK
x2
x2
PLAY MUSIC
Press
“Power” twice
STOP/PAUSE MUSIC
Press
“Power“ once
BACKTRACK
Press
“Down“ twice
x2
FAST FORWARD
Press
“Up“ twice
MUSIC SHARE (AMP PRO & AMP PLUS ONLY)
x2
x2
1) Pair Units for Group Intercom(See Above)
2) On Unit 1 quickly press “Power” & Down” two
times.
3) On Unit 2 quickly press “Power” & Up” two
times.
4) Both Units will blink blue and red until paired.
On successful pairing units will blink Blue.
x2
x2
UNIT 1
Quickly Press
“Power” & Down
twice
UNIT 2
Quickly Press
“Power” &“Up“
twice
GROUP INTERCOM
UNIT 1
UNIT 2
UNIT 3
UNIT 4 PLUS
1) Power off all the units.
2) On the 1st unit, hold “Power“ and “Down“ 5 seconds, LED will blink
purple.
3) On the 2nd unit, hold “Power“ and “Up“ button 5 seconds, LED will
blink purple, wait until the previous unit blinks blue, then proceed to
next step.
4) Repeat step 3 if you have more units. Go to step 5 if no more units.
5) To end the pairing
process, press “Power”
on the last unit in the
chain.
6) Power Off all Units to
store pairing into
memory.
ENABLE 2 PARTY PRIVATE INTERCOM WITHIN GROUP INTERCOM
1) Make sure all intercom units are powered on and Paired for
Group Intercom(see group intercom) and are in Intercom Mode.
2) On unit 1 and unit 2 press “Power” and “Up” until indicator
blinks purple.
3) After both units are blinking purple press “Power” on unit 2 to
end the pairing process.
Note: You will only need to pair this ONCE and you can create
multiple private groups in a Group Intercom.
UNIT 1 & 2
Press
“Power” &“Up“
Indicator will
Blink Purple
UNIT 2
Press
“Power”
to end pairing
TO ENTER GROUP INTERCOM FROM PRIVATE INTERCOM
Press “Power” once. A single “Beep” will sound.
PHONE CALLS
Pick up Incoming Call
Press “Power” Once
End Call In Progress
Hold “Power” for 2 Seconds
Reject Incoming Call
Hold “Power” for 2 Seconds
Voice Dial
Hold “Power” and Down for 2 Seconds
Last Number Redial
Hold “Power” and Up for 2 Seconds
MUSIC
Play
Press “Power” 2 Times
Stop
Press “Power” 1 Time
Fast Forward Track
Press “Up” Button 2 Times
Backtrack
Press “Down” Button 2 Times
GROUP INTERCOM
Press all 3 buttons
for 2 seconds
PHONE FUNCTIONS
PAIRING TO SMARTPHONE
Unit 1 will now share it’s music to unit 2
Bluetooth: V4.2 (BR/EDR/BLE), Class 1
Profiles: HSP, HFP, A2DP
Intercom: AVRCP
Carrier Frequency: 2.402 - 2.480 GHz
Range: Up to 700m (0.43mi)
AMP Pro Multi-Hop Intercom: 2 Users and Up
AMP Plus Multi-Hop Intercom: 2-6 Users
AMP Multi-Hop Intercom: 2 Users
RESET
TO ENTER PRIVATE INTERCOM FROM GROUP INTERCOM
Press “Power” once. A double “Beep” will sound.
CROSS-BRAND INTERCOM PAIRING
1) Set your [Other brand] intercom device in
pairing mode.
2) Power on the AMP unit by pressing the
power button 10 seconds until LED blinks
purple. Pairing is successful when AMP
LED blinks blue.
3) Power Off AMP unit to store pairing into
memory.
GROUP & CROSSBRAND INTERCOM USE
START INTERCOM
Hold “Up” 2 seconds
STOP INTERCOM
Hold “Down” 2 seconds
STATUS INDICATOR REFERENCE
Pairing as Unit 1
Unit is off, “Power” and “Down” for 3 seconds
1)
Off (No Power)
N/A
Pairing as Unit 2
Unit is off, “Power” and “Up” for 3 seconds
2)
On (Bluetooth not connected)
Blinks Blue Quickly
Connect intercom
Hold “Up” for 2 Seconds
3)
On (Bluetooth connected)
Blink Blue Slowly
Disconnect intercom
Hold “Down” for 2 Seconds
4)
Phone & Music Device Pairing Mode
Blinks Blue and Red Alternately
5)
Call in Progress
Blinks Blue Very Slowly
6)
In-coming Call
Blinks Blue and Red Alternately
7)
Battery Low
Blinks Red Every 2 Seconds
8)
Power Down
Blinks Red 5 Times
9)
Intercom Connected
Blinks Blue Twice Every 2 Seconds
10)
Intercom Pairing Mode (first unit)
Blinks Purple Fast
11)
Intercom Pairing Mode (subsequent unit)
Blinks Purple Slowly
OPEN INTERCOM
Activate Open Pairing
Unit is off, hold “Power” for 10 seconds
Activate [other brand] Pairing
Refer to the Respective Manufacturer User Manual
Connect intercom
Hold “Up’ for 2 Seconds
Disconnect intercom
Hold ”Down” for 2 Seconds
PRIVATE INTERCOM
Set Up
While all units are connected, hold “Power” and “Up”
12)
Battery Charging
Solid Red
Switch To Group Intercom
Press “Power” 1 Time
13)
Battery Fully Charged
Solid Blue
Switch To Private Intercom
Press “Power” 1 Time
14)
Battery Faulty
Solid Purple
AMP SERIES USER GUIDE
Thank you for purchasing the UCLEAR Digital AMP Series Bluetooth Helmet
Communication System. Our customers are our top priority, and we strive for
100% satisfaction. If you have any questions on how to operate, install or
general questions about the Amp system or it’s accessories please do not
hesitate to contact us. Tech Support: M-F 8am-5pm MST. 1-855-248-9283
FCC NOTICES
FCC COMPLIANCE STATEMENT FCC ID:NMCAMP
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operations.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
ATTENTION
PLEASE READ THROUGH THE OPERATING INSTRUCTIONS TO UNDERSTAND HOW
TO OPERATE THE AMP SYSTEM, IN PARTICULAR THE SAFETY INSTRUCTIONS.
> Please note that there are some countries that by law disallow the rider to set the UCLEAR
Digital Amp unit to a volume that prevents you hearing your surroundings.
> Please note that in some countries the use of both speakers simultaneously is authorized
only out of public traffic conditions.
> Please check with the relevant authorities for local safety legislation before using UCLEAR
Digital Amp unit on the road.
> Please learn how to use the buttons by looking into the mirror before using the UCLEAR
Digital Amp unit on the road.
> Prolonged exposure to loud sounds may lead to permanent hearing damage.
> Speaker volume is greater than 90 dB may lead to permanent hearing damage.
> Do not attempt to place an outgoing call through the mobile phone while riding on the
motorcycle, ATV/UTV at any point of time.
> Please do not use the UCLEAR Digital Amp unit in anyway that may distract you or hinder
your judgement while on the move. Never compromise your safety and the safety of others.
About the SAR information,please check the FCC ID:NMCAMP on fcc website.
WARNING
NOTICES
WARRANTY
Without prejudice of legal warranty, the AMP Unit is covered under a (2) Two year warranty
and a (1) One Year Warranty for Accessories by manufacturer from the date of purchase.
Please provide the proof of purchase when you return the item to the supplier. The warranty
covers manufacturing defects only. The warranty is voided by any unauthorized repairs,
misuse, misapplication, tampering of the product, modifications, upgrading or results of any
failures to follow the guidelines as set out in the product brochure or by any of the actions
specified in this brochure or anywhere in our technical publishing released to the public from
time to time which would have voided the warranty. Your product must be registered at
uclear-digital.com upon purchase.
Warranty does not cover data recovery and physical deterioration due to use, damages
resulting from accidents, storage, loss or data loss or damage during repairs or transits. The
sender will bear all transportation charges for functioning products but which were declared
defective.
LIMITATIONS OF WARRANTY
All product warranties for the product by are limited to those mentioned in the product
manual. You must register your product upon purchase at uclear-digital.com, and warranty
period is good for (2) two years for Amp Control Units and (1) one year on accessories from
purchase date.
WAIVER AND DISCLAIMER
BITwave, and all their representatives, partners, agents, distributors, suppliers and resellers
shall not be liable and will be held harmless from any and all litigation, claims, debts,
demands, actions and liability which may arise, directly or indirectly, from operating or using
the product for any damages, losses, distress, pain, suffering, discomfort, loss and injuries
including bodily harm illness, strains, fractures, partial and/or total paralysis, death or other
ailments that could cause serious disability either to any persons, or any parties whether the
user or other third parties or their possessions, or to any goods, vehicles, properties, assets
among others including your own suffered by any persons, organizations, or any third parties
whether physical or otherwise and which may accrue to you in the future, to the fullest extent
permitted by law as a result of the use, operation, malfunctioning, misuse, disposal or repairs
of the product or any other reasons, conditions or circumstances or attempts to do so whether
due to negligence, omissions, or otherwise of BITwave, or any of their representatives,
partners, agents, .distributors, suppliers, resellers, designer, manufacturer or any others in its
supply and distribution chain or any third parties involved. All risks from operating or usage
of the product rest solely and entirely with the user of this product, the original purchaser or
any third parties, who assumes full responsibility for all injuries, losses and/ or damages,
whether caused in whole or in part by the negligence, omissions or other conduct of others,
including that of BITwave, and all their representatives, partners, agents, distributors,
suppliers, resellers and all others in its supply and distribution chain either due to the
designer’s or manufacturer’s negligence or omissions or any third parties involved.
CORRECT DISPOSAL OF THIS PRODUCT
Do not dispose this product with other household wastes at the end of its working life. There
is a separate collection system for used electronic products in accordance with legislation
that requires proper treatment, recovery and recycling. Household users should contact either
the retailer where they purchased this product, or their local government office, for details of
where and how they can take this item for environmentally safe recycling. Business users
should contact their suppliers and refer to the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
PRODUCT INFORMATION
BITwave, and all their representatives, agents, distributors, suppliers or resellers shall not be
held responsible for any consequences arising from any errors or omissions in the guide or
resulting directly or indirectly from the use of the information herein. BITwave reserves the
right to amend or improve the product design or user guide without any restrictions and
without any obligation to notify users. All information here is accurate as of the date of
printing.
Please periodically check for the latest firmware version to receive feature enhancements
on ClearLink App. Dowmload Clearlink App at the Google Play or Apple App store.
PERSONAL SAFETY
Do not open the seal of the hardware, tamper, repair or modify any parts. Do not touch the
product with metal objects or parts or chemical products. Violation of the above will lead to
potential fire hazards and mishaps. Please contact UCLEAR Digital technical support or your
if your product malfunctions.
Always comply with the local law and traffic regulations. Where use of the product is not
permitted or allowed by any laws and regulations including the traffic laws of your country,
we warn you not to go against such restrictions. You will bear the full responsibilities of any
breaches of Law and Regulations.
You should not allow the operations or use of the product or any attempts to use it by any
persons including yourself to compromise anyone’s safety including your own or to cause
harm to any vehicles, property, objects, livestock, inventories, assets and the like under any
circumstances. You or any users of the product are to take all necessary safety measures and
precautions and to remain alert to all surrounding conditions. You are warned not to operate
the product if you are not physically capable of doing so in a safe manner, if you have or will
consume any alcohol or any mind-altering substance during its operation so that your
alertness is compromised or if you have any medical conditions or needs that may
compromise your abilities to do so in a safe manner. We warn you of the inherent,
unforeseeable and unlimited risks and dangers in using the product while in traffic, including
injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that
could cause serious disability due to any causes. This product is only for use by persons
eighteen (18) years of age and above who have understood the warnings, risks and the terms
of use. You confirm that you have read this release of liability and fully understand its terms
and that you have given up substantial rights by using or attempting to use the product.
> Charging and handling rechargeable battery products incorrectly may cause them to
overheat, catch fire or explode. To prevent this please follow the instructions below:
i) Never change the batteries yourself, always contact UCLEAR Digital to perform the
replacement for you.
ii) When charging, use ONLY the charging cable provided or a replacement cable from a
UCLEAR Digital dealer. Using similar, compatible or any other cables may lead to
permanent product damage and will void the product warranty.
> Never make any modifications to any part of the UCLEAR Digital Amp unit in any way as it
may cause the system to malfunction causing hurt to you.
> Do not modify your helmet to use with this system - it is not necessary to do so.
EQUIPMENT NOTICES
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the Equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. The portable device is designed to meet the
requirements for exposure to radio waves established by the Federal Communications
Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram
of tissue. The highest SAR value reported under this standard during product certification for
use when properly worn on the body is 0.044 W/kg.
WARNING
BATTERY WARNING
The UCLEAR helmet communicator contains a rechargeable lithium ion polymer battery. To
reduce risks of fire or burns, do not disassemble, crush, puncture, short external contacts or
dispose in fire or water.
CHARGING NOTICE
To reduce the risk of personal injury, electrical shock, fire or damage to equipments, please
follow all the instructions below:
- Do not immerse the product, AC adaptor or speakers in water.
- Do not install, place or use the product near any source of heat for example: stove, radiator,
oven, toaster, coffee maker or other apparatus that gives off heat.
- Always use the provided AC power adaptor and cable included in the package to charge the
product. Use of any incorrect power supply to charge the product may cause permanent
damage to the product and render the warranty void.
CONTACT AND SUPPORT INFORMATION
For USA Tech support and warranty department.
M-F 8am-5pm MST.
1-855-248-9283
BITwave USA LLC
1488 E lron Eagle Dr.
Eagle, ID 83616
For additional information please visit our website at www.uclear-digital.com
LICENCES
The UCLEAR trademark and logo is exclusively owned by BITwave Pte Ltd. Any use of the
mark by any other parties without prior written permission of BITwave Pte Ltd constitutes an
infringement of legal rights. The Bluetooth trademark is owned by Bluetooth SIG and is used
under licence by BITwave Pte Ltd.
COPYRIGHTS
Copyright © 2016 BITwave Pte Ltd. All rights reserved. No part of this guide may be
reproduced in any form or by any process whatsoever without prior written consent from
BITwave Pte Ltd.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : Rod
Create Date                     : 2016:02:25 15:55:35+08:00
Modify Date                     : 2016:02:25 15:55:35+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.1.14 (Windows)
Format                          : application/pdf
Title                           : 2016 Amp All Language User Guide Front.ai
Creator                         : Rod
Document ID                     : uuid:a71358ef-fa1b-445a-8d44-902d74b02e5c
Instance ID                     : uuid:2fa7a97f-1884-41b8-baa3-06327b765f2f
Page Count                      : 2

EXIF Metadata provided by EXIF.tools