BOLENS Front Tine, Gas Tiller Manual L0401092

User Manual: BOLENS BOLENS Front Tine, Gas Tiller Manual BOLENS Front Tine, Gas Tiller Owner's Manual, BOLENS Front Tine, Gas Tiller installation guides

Open the PDF directly: View PDF .
Page Count: 20

Operator's Manual

Front Tine Tiller

Model 332

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-

covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting

applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have

similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized

service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.

TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

PRINTED IN U.S.A. FORM NO. 769-00521

(10/2002)

TABLEOFCONTENTS

Content Page

Important Safe Operation Practices ................................................................... 3

Assembling Your Tiller ....................................................................................... 5

Know Your Tiller ................................................................................................. 7

Operating Your Tiller .......................................................................................... 8

Making Adjustments .......................................................................................... 11

Maintaining Your Tiller ....................................................................................... 12

Troubleshooting ................................................................................................. 14

Parts List ............................................................................................................ 14

FINDINGMODELNUMBER

This Operator's Manual is an important part of your new Tiller. It will help you assemble, prepare and

maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the

equipment and copy the information from it in the space provided below. The information on

the model plate is very important if you need help from our Customer Support Department or

an authorized dealer.

You can locate the model number by standing in the operating position behind the unit and looking

down at the center of the rear tine cover. A sample model plate is explained below. For future

reference, please copy the model number and the serial number of the equipment in the space below.

Copy the model number here:

Copy the serial number here:

ENGINEINFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-

rating, specifications, warranty and service. Please refer to the engine manufacturer's Owner's/Operator's

Manual packed separately with your unit for more information.

CONTACTINGCUSTOMERSUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, please call Customer Support Department.

Call 1(866) 840-6483 or 1(330) 558-7220 to reach a Customer Support representative.

Please have your unit's model number and serial number ready when you call. See previous

section to locate this information, You will be asked to enter the serial number in order to

process your call.

SECTION1: IMPORTANTSAFEOPERATIONPRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could

endanger the personal safety and/or property of yourself and others. Read and follow all instructions in

this manual before attempting to operate this machine. Failure to comply with these instructions may

result in personal injury. When you see this symbol-- heed its warning.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to State of California to cause cancer and birth defects or other reproductive

harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can

result in serious injury. This machine is capable of amputating hands and feet. Failure to observe the

following safety instructions could result in serious injury or death.

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe

place for future and regular reference and for

ordering replacement parts.

2. Be familiar with all controls and their proper

operation. Know how to stop the machine and

disengage them quickly.

3. Never allow children under 14 years old to operate

this machine. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and should be trained

and supervised by a parent.

4. Never allow adults to operate this machine without

proper instruction.

5. Keep bystanders, helpers, pets and children at least

75 feet from the machine while it is in operation.

Stop machine if anyone enters the area.

Preparation

1. Thoroughly inspect the area where the equipment is

to be used. Remove all stones, sticks, wire, and

other foreign objects which could be tripped over

and cause personal injury.

2. Wear sturdy, rough-soled work shoes and close

fitting slacks and shirt. Loose fitting clothes or

jewelry can be caught in movable parts. Never

operate this machine in bare feet or sandals.

3. Disengage clutch levers and shift (if provided) into

neutral ("N") before starting the engine.

4. Never leave this machine unattended with the

engine running.

5. Never attempt to make any adjustments while

engine is running, except where specifically

recommended in the operator's manual.

6. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

7. Use only an approved gasoline container.

8. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

9. Never fuel machine indoors.

10. Never remove gas cap or add fuel while the engine

is hot or running.

11. Allow engine to cool at least two minutes before

refueling.

12. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to provide space for

fuel expansion.

13. Replace gasoline cap and tighten securely.

14. If gasoline is spilled, wipe it off the engine and

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

15. Never store the machine or fuel container inside

near an open flame, spark or pilot light (e.g.

furnace, water or space heater, clothes dryer etc.).

16. Allow machine to cool 5 minutes before storing.

Operation

1. Do not put hands or feet near rotating parts. Contact

with the rotating parts can amputate hands and feet.

2. Do not operate machine while under the influence

of alcohol or drugs.

3. Never operate this machine without good visibility

or light. Always be sure of your footing and keep a

firm hold on the handles.

4. Keep bystanders, helpers, pets, and children at

least 75 feet from the machine while it is in

operation. Stop the machine if anyone enters the

area.

5. Be careful when tilling in hard ground. The tines

may catch in the ground and propel the tiller

forward. If this occurs, let go of the handle bars and

do not restrain the machine.

6. Exercise extreme caution when operating on or

crossing gravel surfaces. Stay alert for hidden

hazards or traffic. Do not carry passengers.

7. Never operate the machine at high transport

speeds on hard or slippery surfaces.

8. Exercise caution to avoid slipping or falling.

9. Lookdownandbehindandusecarewhenin

reverseorpullingmachinetowardsyou.

10. Starttheengineaccordingtotheinstructionsfound

inthismanualandkeepfeetwellawayfromthe

tinesatalltimes.

11. Afterstrikingaforeignobject,stoptheengine,

disconnectthesparkplugwireandgroundagainst

theengine.Thoroughlyinspectthemachineforany

damage.Repairthedamagebeforestartingand

operating.

12. Disengageallclutchleversandstopenginebefore

youleavetheoperatingposition(behindthe

handles).Waituntilthetinescometoacomplete

stopbeforeuncloggingthetines,makingany

adjustments,orinspections.

13. Neverrunanengineindoorsorinapoorly

ventilatedarea.Engineexhaustcontainscarbon

monoxide,anodorlessanddeadlygas.

14. Mufflerandenginebecomehotandcancausea

burn.Donottouch.

15. Usecautionwhentillingnearfences,buildingsand

undergroundutilities.Rotatingtinescancause

propertydamageorpersonalinjury.

16. Donotoverloadmachinecapacitybyattemptingto

tillsoiltodeepattofastofarate.

17. Ifthemachineshouldstartmakinganunusualnoise

orvibration,stoptheengine,disconnectthespark

plugwireandgrounditagainsttheengine.Inspect

thoroughlyfordamage.Repairanydamagebefore

startingandoperating.

18. Keepallshields,guardsandsafetydevicesinplace

andoperatingproperly.

19. Neverpickuporcarrymachinewhiletheengineis

running.

20. Useonlyattachmentsandaccessoriesapprovedby

themanufacturer.Failuretodoso,canresultin

personalinjury.

21. Ifsituationsoccurwhicharenotcoveredinthis

manual,usecareandgoodjudgment.Contactyour

dealerortelephone1-800-800-7310forassistance

andthenameofyournearestservicingdealer.

Maintenance& Storage

1. Never tamper with safety devices. Check their

proper operation regularly.

2. Check bolts and screws for proper tightness at

frequent intervals to keep the machine in safe

working condition. Also, visually inspect machine for

any damage.

3. Before cleaning, repairing, or inspecting, stop the

engine and make certain the tines and all moving

parts have stopped. Disconnect the spark plug wire

and ground it against the engine to prevent

unintended starting.

10.

Do not change the engine governor settings or over-

speed the engine. The governor controls the

maximum safe operating speed of the engine.

Maintain or replace safety and instruction labels, as

necessary.

Follow this manual for safe loading, unloading,

transporting, and storage of this machine.

Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

such as a water heater, furnace, clothes dryer etc.

Always refer to the operator's manual for proper

instructions on off-season storage.

If the fuel tank has to be drained, do this outdoors.

Observe proper disposal laws and regulations for

gas, oil, etc. to protect the environment.

YourResponsibility

1. Restrict the use of this power machine to persons

who read, understand and follow the warnings and

instructions in this manual and on the machine.

2. The safety label on the tiller is reproduced below for

your review. To ensure safe operation of the tiller,

follow the instructions on all labels closely.

TO A_3 _EI_Q_ _IJU[_'¢

SECTION2: ASSEMBLINGYOURTILLER

NOTE: This operator's manual covers various models

of tillers. The units illustrated may vary slightly from

your unit. Follow only those instructions which pertain

to your model number.

NOTE: References to right or left side of the tiller are

determined from behind the unit in the operating

position.

ToRemoveUnitFromCarton

Remove staples, break glue on top flaps, or cut

tape at carton end and peel along top flap to open

carton.

Remove loose parts included with unit (i.e.,

operator's manual, etc.).

Cut corners and lay carton down flat.

Remove packing material.

Roll or slide unit out of carton. Check carton

thoroughly for loose parts.

Extend control cable and lay on the floor. Be careful

not to bend or kink control cable.

IMPORTANT: This unit is shipped without gasoline or oil

in the engine. Be certain to service engine with gasoline

and oil as instructed in the separate engine manual

before operating your machine.

LoosePartsIn Carton

Tailpiece and Depth Stake

NOTE: All hardware needed for assembly is attached

to the loose parts orthe tiller.

BeforeAssembly

_WARNING: Disconnect the spark plugwire and ground it against the engine to

prevent unintended starting.

AssemblingTheHandle

Remove the handle adjustment lever from handle

and lift up upper handle to raise in operating

position. See Figure 1.

Reinsert adjustment lever through the lower hole,

tightening the lever into lock nut on the retainer

bracket.

Once the lever is in the lock nut, the handle can be

moved to the desired position and then tighten

securely.

Handle

Adjustment Lever

Figure 1

.Handle

Adjustment Lever

-Retainer Bracket

Self-Tapping

Screws

Tail

Figure 2

AttachingTailpiece andDepthStake

Remove the two self-tapping screws on the frame

and slide the tailpiece into the frame, with the lower

hole in the tailpiece toward the front, See Figure 2,

Secure tailpiece with the screws just removed,

CheckCableAdjustment

With the clutch lever disengaged, pull starter rope

slowly several times. The tines should not turn. If

they turn, the cable is not adjusted properly.

To adjust the cable, loosen the nut near the top of

the cable and unscrew the cable to provide

additional slack in wire. See Figure 3.

Tighten the nut and check again for proper

adjustment.

Clutch Lever_

Loosen Nut_ _

Figure 3

SECTION3: KNOWYOURTILLER

Clutch Control

Handle Adjustment Lever

--....

Figure 4

WARNING: Read, understand, and

follow all instructions and warnings on

the machine and in this manual before

operating,

TineClutchControl

The clutch control lever is located on the left handle.

Squeezing the lever against the handle engages the

tine drive. Release the lever to stop the tines from

turning. See Figure 4

DepthStake

The depth stake is located inthe rear of the tiller and it

controls the tilling depth. See Figure 4

HandleAdjustmentLever

The handle may be adjusted to the height desired.

Loosen the handle adjustment lever a few turns and

pivot handle up or down to desired position. Tighten

lock. See Figure 4.

ThrottleControl

The throttle control lever is located on the engine. It

controls the engine's speed and stops the engine.

With the throttle control pushed completely forward,

the carburetor is in START or FAST position. Use

maximum engine speed for deep tilling.

Pull the throttle control back to reduce engine

speed to IDLE. Throttle control should be at IDLE

for transporting the tiller.

Pull the throttle completely back to stop the engine.

ChokeLever

The choke lever is located near the throttle control. It is

used to enrich the fuel mixture when starting a cold

engine.

StarterHandle

The starter handle is located on the engine and is

used to manually start the engine.

EngineControls

See the separate engine manual for additional

information and functions of the engine controls.

SECTION4: OPERATINGYOURTILLER

WARNING: Read, understand, and

follow all instructions and warnings on

the machine and in this manual before

operating.

BeforeStarting

GasAndOilFill-Up

Service the engine with gasoline and oil as instructed in

the separate engine manual packed with your tiller.

Read instructions carefully.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel machine indoors or while the

engine is hot or running.

StartingEngine

_b WARNING: Be sure no one is standing

in front of the tiller while the engine is

running or being started.

Attach spark plug wire to spark plug. Make sure the

metal cap on the end of the spark plug is fastened

securely over the metal tip on the spark plug.

Make sure that the tine clutch control is

disengaged.

Place the throttle control in the FAST position.

Move choke lever to CHOKE position. A warm

engine requires little or no choke.

Grasp starter handle and pull rope out slowly until

engine reaches start of compression cycle (rope

will pull slightly harder at this point). Let the rope

rewind slowly.

Pull rope with a rapid, continuous, full arm stroke.

Keep a firm grip on starter handle. Let rope rewind

slowly. Do not let starter handle snap back against

starter. Repeat until engine starts.

When engine starts, move choke lever on engine

halfway between CHOKE and RUN. As the engine

warms up, move the lever to RUN position.

Refer to engine manual for additional engine

information.

StoppingEngine

Move throttle control lever to STOP or OFF

position.

Disconnect spark plug wire from spark plug and

ground against the engine.

UsingYourTiller

Your tiller (also known as a cultivator) is aprecision

built machine designed for seed bed preparation,

cultivating, furrowing and mulching. It is engineered to

minimize the hardest work in the vegetable or flower

garden, to till the soil for planting and cultivating, and to

perform many other useful labor saving tasks in the

garden.

WheelPosition

The tiller is shipped with the wheels adjusted such that

the unit sits level. While tilling, as the tines enter the

ground and the front of the tiller lowers, the wheels

must be raised to level the unit, which is essential for

proper engine operation. This adjustment is made by

removing the clevis pin and hairpin clip from wheel

yoke, raising the wheels to the desired height, and

replacing the clevis pin and hairpin clip. See Figure 5.

Stake

Hairpin Yoke

& Clevis Pins

Figure 5

ControllingSpeedAndTillingDepth

Wheel YokeAdjustment

Place wheel yoke so that the wheels are forward

(nearest point between wheels and tines) for shallow

tilling, cultivating and transport. The forward speed will

increase. Turn yoke around (farthest point between

wheels and tines) for deep tilling. Forward speed will

decrease. See Figure 6.

Transport

Position

Figure 7

Wheel Setting For

Deep Tilling

For Deep Tilling For Shallow Tilling

Figure 6

DepthStakeAdjustment

The depth stake acts as a brake for the tiller and

controls the depth and speed at which the machine will

operate. Remove the clevis pin and hairpin clip to raise

or lower depth stake. Refer to Figure 5.

By increasing the depth of the depth stake, the forward

speed of the machine is reduced and the working depth

is increased. When the depth stake is raised, the

working depth of the machine is reduced and the

forward speed is increased. The working depth of the

machine may be predetermined by setting the depth

stake and wheels so that the wheels are about four

inches from the ground when the tines and depth stake

are resting on the ground. This setting will permit a

working depth of about four inches. When presetting

the working depth, the handles should be adjusted so

the hand grips are a little above waist. The tiller will be

lower when the tines and depth stake penetrate the

ground. See Figure 7.

When tilling, leave approximately 8 inches of untilled

soil between the first and second tilling paths, then

make the third path between the first and second. In

some soils, the desired depth is obtained the first time

over the garden. In other soils, the desired depth is

obtained by going over the garden two or three times. In

the latter case, the depth stake should be lowered

before each succeeding pass over the garden. Passes

should be made across the length and width of the

garden alternately. Rocks which are turned up should

be removed from the garden area. See Figure 8.

Figure 8

HandlePressure

Further control of tilling depth and travel speed can be

obtained by variation of pressure on the handles.

A downward pressure on the handles will reduce

the working depth and increase the forward speed.

An upward pressure on the handles will increase

the working depth and reduce the forward speed.

The type of soil and working conditions wilt determine

the actual setting of the depth stake and the handle

pressure required.

TransportingtheTEller

To transport the tiller to or from the garden, pivot

the depth stake forward and out of the way. With

the throttle control in SLOW position, the unit wilt

walk freely on the lawn. If the operator does not

allow the tiller to move freely, the unit will start to till

the surface. Refer to Figure 7.

Cultivating

For cultivating, a two to three inch depth is desirable.

Setting the wheels and depth stake so that the wheels

are about two inches above the ground while the tiller is

resting on the tines and depth stake will allow the

machine to work at cultivating depth. The throttle

should be set to control forward movement to a stow

walking speed. With the outer tines installed, the

working width of the machine is 22 or 24 inches. For

cultivation, this may be reduced to 13 inches by

removing the outer tines. Refer to the Adjustment

Section. When laying out plant rows, be sure to allow

enough width to permit cultivation between the rows. In

growing corn or similar crops, check-row planting wilt

permit cross cultivation and practically eliminate hand

hoeing. See Figure 9.

%.#"

Figure 9

The tiller has many uses other than tilling and

cultivating a garden. One of these is the preparation of

lawn area for seeding. The tiller wilt prepare a deep

seed bed which will be free of hard untilled spots,

allowing a better stand of grass to grow. The tiller is

very useful for loosening hard soil for excavation with a

shovel. No tedious handwork will be necessary. Your

tiller may be used for mixing compost in the pile, or for

mixing it with the soil in your garden. This should be

done after the soil has been broken to the full working

depth. The compost should be worked in to a depth of

six to seven inches. This may be done by working the

length of the garden and then by making separate

passes across its width. The addition of decayed

organic matter wilt substantially increase the fertility of

your garden. For proper decaying action, fertilizer

should be applied and worked in with the mulch

materials. Breaking up leaves and straw and mixing it

with several inches of soil causes the soil to hold

moisture longer and allows proper aeration of the plant

root system. This also retards the growth of weeds.

SECTION5: MAKINGADJUSTMENTS

WARNING: Disconnect the spark plugwire and ground it against the engine

before performing any adjustments.

EngineAdjustment

Refer to the separate engine manual for engine

adjustment instructions.

WheelAdjustment

To adjust the wheel yoke and wheel position, refer to

the Operating Section.

DepthStakeAdjustment

To adjust the depth stake to a desired position, refer to

the Operating Section.

ClutchControlAdjustment

Periodic adjustment of the belt tension may be required

due to normal stretch and wear on the belt. To adjust

the clutch control lever, refer to the Assembly Section.

TineWidthAdjustment

The tilling width of the unit is 22 inches. Tilling width can

be increased to 24 inches by removing the clevis pins

and hairpin clips, sliding the outer tines out one inch,

and securing in this position with the clevis pins and

hairpin clips. For cultivation, reduce the tine width to 13

inches by removing the outer tines completely.

See Figure 10

•I24" =-

13" -_

Figure 10

SECTION6: MAINTAININGYOURTILLER

WARNING: Disconnect the spark plug

wire and ground it against the engine

before performing any repairs or

maintenance.

Engine

Refer to the separate engine manual for engine

maintenance instructions.

Maintain engine oil as instructed in the separate

engine manual packed with your unit. Read and follow

instructions carefully.

Service air cleaner every ten hours under normal

conditions. Clean every hour under extremely dusty

conditions. Poor engine performance and flooding

usually indicates that the air cleaner should be

serviced. To service the air cleaner, refer to the

separate engine manual packed with your unit.

IMPORTANT: Never run your engine without air cleaner

completely assembled.

The spark plug should be cleaned and the gap reset

every 25 hours of engine operation. Spark plug

replacement is recommended at the start of each tiller

season; check engine manual for correct plug type and

gap specification.

Clean the engine regulady with a cloth or brush. Keep

the cooling system (blower housing area) clean to

permit proper air circulation which is essential to engine

performance and life. Be certain to remove all dirt and

combustible debris from muffler area.

CleaningTineArea

Clean the underside of the tine shield after each use.

The dirt washes off the tines easier if rinsed off

immediately instead of after it dries. Always towel dry

the tiller afterwards and apply a light coat of oil or

silicone to prevent rusting or water damage.

IMPORTANT: Never use a "pressure washer" to clean

your tiller. Water can penetrate tight areas of the tiller

and its chain case and cause serious damage to the

unit.

BeltReplacement

Your tiller has been engineered with a belt made of

special material (Kevlar Tensile) for longer life and

better performance. It should not be replaced with an

off-the-shelf belt. Order alt belts through your

authorized service dealer.

Disconnect and ground spark plug wire against the

engine.

Remove the two hex washer screws from the front

of the belt cover and remove the lock nut and flat

washer from the side of the belt cover.

Remove the belt cover. See Figure 11.

Belt Cover

Hex Washe_

Screw Lock Nut &

Lubrication

Transmission

The transmission is pre-lubricated and sealed at the

factory. It requires no checking. See an authorized

service dealer for any service issues.

ClutchHandle

Lubricate the pivot point on the clutch handle and the

cable at least once a season with light oil. The control

must operate freely in both directions.

PivotPoints

Lubricate all pivot points and linkages at least once a

season with light oil.

Tine Shafts

Remove tine assemblies and lubricate the tine shafts at

least once a season.

Wheel Shafts

Remove wheel assemblies and lubricate the axle shafts

at least once a season.

Screw

Figure 11

Remove the hex screw and idler pulley from the

idler bracket assembly. See Figure 12,

Reassemble the new belt and reattach idler pulley

to secure in place.

Replace belt cover assembly and secure with the

hardware removed earlier.

Screw

•Idler Pulley

Refer to the engine manual for correct engine

storage instructions.

Wipe tines with oiled rag to prevent rust.

Store tiller in a clean, dry area. Do not store next to

corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in

an unventilated or metal storage shed, care should be

taken to rustproof the equipment. Using a light oil or

silicone, coat the equipment and especially any

springs, bearings, and cables.

Figure 12

Off-SeasonStorage

If the tiller will not be used for a period longer than 30

days, the following steps should be taken to prepare the

tiller for storage.

Clean the exterior of engine and the entire tiller

thoroughly. Lubricate the tiller as described in the

lubrication instructions.

We do not recommend the use of pressure

washers to clean your unit. They may cause

damage to electric components, spindles, pulleys,

bearings or the engine. The use of pressure

washers will result in shortened life and reduce

serviceability.

SECTION7: TROUBLESHOOTING

Problem Cause

Engine fails to start

Engine runs erratic

1. Spark plug wire disconnected.

2. Fuel tank empty or stale fuel.

3. Throttle control lever not in correct

starting position. (If equipped)

4. Choke not in ON position.

5. Blocked fuel line.

6. Faulty spark plug.

7. Engine flooded

1. Spark plug wire loose.

2. Unit running on CHOKE.

3. Blocked fuel line or stale fuel.

Engine overheats 1.

Tines do not engage 1.

Vent plugged.

Water or dirt in fuel system.

Dirty air cleaner.

Carburetor out of adjustment.

Engine oil level low.

Dirty air cleaner.

Air flow restricted.

Carburetor not adjusted properly.

Foreign object lodged in tines.

2. Tine clevis pin(s) missing.

3. Control cable not adjusted properly.

4. Belt worn and/or stretched.

5. Pulley and idler not in correct

adjustment.

Remedy

1. Connect wire to spark plug.

2. Fill tank with clean, fresh gasoline.

3. Move throttle lever to start position.

4. Move lever to ON position.

5. Clean fuel line.

6. Clean, adjust gap, or replace.

7. Wait a few minutes to restart, but do not

prime. (If Equipped)

1. Connect and tighten spark plug wire.

2. Move choke lever to OFF position.

3. Clean fuel line; fill tank with clean, fresh

gasoline

4. Clear vent.

5. Drain fuel tank. Refill with fresh fuel.

6. Clean following engine manual.

7. Refer to engine manual.

1. Fill crankcase with proper oil.

2. Clean air cleaner.

3. Remove blower housing and clean.

4. Refer to engine manual.

1. Stop tiller completely, check and

discard foreign object.

2. Replace tine clevis pin(s).

3. Adjust control cable.

4. Replace belt.

5. Take unit to authorized service dealer.

NOTE: For repairs beyond the miner adjustments listed above, contact your nearest service dealer.

SECTION8: NOTES

Model332

27 18

49 58

Model332

Ref.

No.

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

27.

28.

29.

30.

31.

32.

33.

Part No.

720-0274

731-0473

686-0002

649-0137

712-0442

738-1225

746-1148

738-1226

710-0189

736-0242

786-0340

710-0606

719-0279

712-0720

786-0341

649-0136

710-0805

711-0415

750-0890

786-0003

786-0004

786-0005

714-0149B

712-3004A

712-3010

710-3180

710-0604A

710-0602

738-0934

712-0240

736-0171

786-0138A

786-0139A

Part Description

Grip

Clutch Grip

Clutch Lever

Handle Assembly

Lock Nut Cap 1/4-20

Shoulder Screw

Clutch Cable

Shoulder Screw

Hex Cap Screw 5/16-18 x 3,0

Bell Washer ,340 ID x ,872 OD

Adjustable Handle Crank

Hex Cap Screw 1/4-20 x 1,5

Rope Guide

Flange Nut 5/16-18

Retainer Bracket

Handle Tube

Hex Cap Screw 5/16-18 x 1,5

Clevis Pin 3/8 x 1.62

Spacer

Tailpiece Bracket LH

Tailpiece Bracket RH

Depth Bar

Cotter Pin

Hex Flange Lecknut 5/16-18

Hex Nut 5/16-18

Hex Cap Screw 5/16-18 x 1,75

Hex Washer Screw 5/16-18 x .625

Hex Washer Screw 5/16-18 x 1,0

Shoulder Screw

Jam Nut 7/16-20

Lock Washer 7/16

Frame RH

Frame LH

Ref. Part No.

No.

34. 712-3004A

35. 711-0919

36. 710-0599

37. 786-0035A

38. 710-0502A

39. 710-3008

40. 786-0053

41. 710-0723

42. 786-0039B

43. 736-0119

44. 710-0107

45. 750-0892

46. 748-0350

47. 756-0971

48. 756-0972

49. 754-0428

50. 736-0452

51. 710-0152

52. 756-0585

53. 736-0312

54. 736-0112

55. 712-3029

56. 710-0599

57. 786-0056

58. 712-0392

59. 736-3020

60. 738-0930

61. 712-0266

62. 786-0144

63. 786-0149

64. 756-0313

65.

Part Description

Flange Lock Nut 5/16-18

Belt Cover Belt

Hex Washer Screw 1/4-20 x .500

Tine Shield 20"

Hex Washer Screw 3/8-16 x 1,25

Hex Cap Screw 5/16-18

Tine Shield Bracket 20"

Hex Cap Screw 3/8-16 x 1.25

Cover Bracket

Lock Washer 5/16

Hex Cap Screw 5/16-24 x .50

Input Spacer .64 ID x 2,4 Lg

Pulley Adapter

Engine Inner Half Pulley

Engine Outer Half Pulley

Belt

Bell Washer .396 ID x 1,140 OD

Hex Cap Screw 3/8-24 x 1.0

Flat Pulley

Retainer Bearing Washer

Spherical Washer ,531 ID x .620 OD

Jam Nut 1/2-20

Hex Washer Screw 1/4-20 x .50

Cover Belt

Lock Nut Cap 1/4-28

Flat Washer .271 ID x ,630 OD

Shoulder Screw

Jam Nut 3/8-16

Idler Bracket

Idler Keeper Bracket

Flat Idler

Model332

Ref.

No.

10.

11.

Part No.

734-1781

738-0929

686-0081A

714-0149B

711-0415

736-0242

710-0189

738-0934

786-0145A

750-0470

686-0091

Part Description

Wheel 8 x 1,75

Shoulder Screw

Wheel Bracket Assembly

Cotter Pin

Clevis Pin

Bell Washer ,340 ID x ,872 OD

Hex Cap Screw 5/16-18 x 3.0

Shoulder Screw

Engine Mounting Plate

Spacer .47 OD x .96Lg

Chain Case Assembly

Ref.

No.

12,

13.

14,

15,

16.

17.

18.

19.

Part No.

712-0429

736-0171

712-0240

642-0002

642-0003

642-0004

642-0005

712-3010

736-0242

710-3180

Part Description

Hex Lock Nut 5/16-18

Lock Washer 7/16

Jam Nut 7/16-20

Inner Tine Assembly - RH 12"

Inner Tine Assembly - LH 12"

Outer Tine Assembly -RH 12"

Outer Tine Assembly - LH 12"

Hex Nut 5/16-18

Bell Washer .340 ID x .872 OD

Hex Cap Screw 5/16-18 x 1,75

MANUFACTURER'S LIMITED WARRANTY FOR:

I I I W _lllmlF IIMIImllMIImlr I

The limited warranty set forth below is given by Troy-Bilt LLC

with respect to new merchandise purchased and used in the

United States, its possessions and territories.

Troy-Bilt LLC warrants this product against defects for a

period of two (2) years commencing on the date of original

purchase and will, at its option, repair or replace, free of

charge, any part found to be defective in materials or

workmanship. This limited warranty shall only apply if this

product has been operated and maintained in accordance

with the Operator's Manual furnished with the product, and

has not been subject to misuse, abuse, commercial use,

neglect, accident, improper maintenance, alteration,

vandalism, theft, fire, water, or damage because of other peril

or natural disaster. Damage resulting from the installation or

use of any accessory or attachment not approved by Troy-Bilt

LLC for use with the product(s) covered by this manual will

void your warranty as to any resulting damage.

Normal wear parts or components thereof are subject to

separate terms as follows: All normal wear parts or

component failures will be covered on the product for a period

of 90 days regardless of cause. After 90 days, but within the

two year period, normal wear part failures will be covered

ONLY IF caused by defects in materials or workmanship of

OTHER component parts. Normal wear parts and

components include, but are not limited to: batteries, belts,

blades, blade adapters, grass bags, rider deck wheels, seats,

snow thrower skid shoes, shave plates, auger spiral rubber,

and tires.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE, through your local authorized

service dealer. To locate the dealer in your area, check your

Yellow Pages, or contact Troy-Bilt LLC at P.O. Box 361131,

Cleveland, Ohio 44136-0019, or call 1-866-840-6483 or 1-

330-558-7220, or log on to our Web site at www.troybilt.cem.

This limited warranty does not provide coverage in the

following cases:

a. The engine or component parts thereof. These items

carry a separate manufacturer's warranty. Refer to

applicable manufacturer's warranty for terms and

conditions.

b. Log splitter pumps, valves, and cylinders have a sepa

rate one year warranty.

c. Routine maintenance items such as lubricants, filters,

blade sharpening, tune-ups, brake adjustments, clutch

adjustments, deck adjustments, and normal

deterioration of the exterior finish due to use or

exposure.

d. Troy-Bilt LLC does not extend any warranty for

products sold or exported outside of the United States,

its possesions and territories, except those sold

through Troy-Bilt LLC's authorized channels of export

distribution.

e. Parts that are not genuine Troy-Bilt parts are not

covered by this warranty.

f. Service completed by someone other than an

authorized service dealer is not covered by this

warranty.

g. Transportation charges and service calls are not

covered.

No implied warranty, including any implied warranty of

merchantability of fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty, whether written or oral, except as

mentioned above, given by any person or entity,

including adealer or retailer, with respect to any product,

shall bind Troy-Bilt LLC. During the period of the

warranty, the exclusive remedy is repair or replacement

of the product as set forth above.

The provisions as set forth in this warranty provide the

sole and exclusive remedy arising from the sale. Troy*

Bilt LLC shall not be liable for incidental or consequential

loss or damage including, without limitation, expenses

incurred for substitute or replacement lawn care services

or for rental expenses to temporarily replace a warranted

product.

Some states do net allow the exclusion or limitation of

incidental or consequential damages, or limitations on how

long an implied warranty lasts, so the above exclusions or

limitations may not apply to you.

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration

of safety features of the product shall void this warranty.

You assume the risk and liability for loss, damage, or injury to

you and your property and/or to others and their property

arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser or to the person for whom it was purchased

as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This

limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

Troy-Bilt LLC,P.O.BOX361131CLEVELAND,OHIO44136-0019; Phone:1-866-840-6483,1-330-558-7220

BOLENS Front Tine, Gas Tiller Manual L0401092

Navigation menu

Versions of this User Manual:

Views

Navigation