BQT Solutions BM68X BM684 Smartcard reader User Manual manual
BQT Solutions (Australia) Pty Ltd BM684 Smartcard reader manual
manual
Drillin ng template • • Wiring diagram 10mm (0.39”) diameeter hole for wire en ntry 2 x 3.6mm (0.14”) diiameter holes for mounting screws Note: d. The shield is connectted to controller 0V refference • A shielded cable is recommended to be used 00 feet) • Maximum data cable length: 150 meters (50 a active low • Buzzer and LED lines are or optional use • RS485 lines are only fo ditional wires/connecttors which are not speccified in the diagram above. • Some models have add These wires are for other requirements. DO NOT connect them unless specified from BQ QT ny damage caused by incorrect connection will w void Solutions or a BQT autthorized distributor. An the warranty Re egulatory Information Thiss device is CE, C‐Tick compllied. Thiss device complies with Partt 15 of the FCC Rules. Operaation is subject to the following two conditions: 1) thiis device mayy not cause interference an nd 2) this device must accep pt any interference, includiing interference that may cause und desired operation of the deevice. FCC ID: QVL‐BM68X NOTTE Thiss equipment has been teste ed and found to comply witth the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits aree designed to provide reaso onable protection against harmful interference in a ressidential enerates uses and can radiaate radio frequency energyy and, if not installed and used in insttallation. This equipment ge acco ordance with the instructio ons, may cause harmful inte erference to radio commun nications. However, there is no guaarantee that interference will w not occur in a particular installation. If this equipment does cause harmful intterference to radio or television reception n, which can be determined d by turning the equipment off and on, the user is encouraged to try t to correct the interferen nce by one or more of the following measures: ‐Reorient or relocate the receiiving antenna. ‐Inccrease the separation between the equipment and recceiver. ‐Connect the equipment into an a outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an expeerienced radio/TV techniciaan for help. Anyy changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate thiss equipment. Speciffications Outp put protocols Pow wer requirement Current consumption Read d range Operating temperaturee Relative humidity Read der dimensions Statu us LED Audiible tone Colo our finish IP raating Wiegand or o RS485 (BM686 only) 7 – 20V DC C (Nominal operatin ng voltage +12V DC C) Normal – 100mA (max) Activated – 130mA (max) Powersave mode – 60mA (max) 20‐40mm (0.8”‐1.6”) ‐25’C to +65’C (‐13’F to 149’FF) 90% max, operating non‐condensing 84.55mm((L) x 42.95mm(W) x 20.70mm(D) (3.33”x1.6 69”x0.81”) Green & Red Internal and external buzzer control, Configurable using “Configurration card” Charcoal IP65 at www.bqttsolutions.com or For furrther technical information, visit our website contacct us for the distribu utor nearest to you TRALIA & PACIFIC AUST BQT Solutions (Australiaa) Pty Limited Leve el 1, 82 Waterloo Ro oad Macquarie Park, NSW 2113, Australia Phon ne: +61 (0)2 8817 2800 Fax: +61 (0)2 8817 2811 ons.com Email: sales@bqtsolutio EUROPE AND MID DDLE EAST BQT Solutions (UK K) Limited Regal House, 70 London Road TWickenham, Mid ddlesex, TW1 3QS United Kingdom Phone: +44 (0)20 8622 4428 22 4421 Fax: +44 (0)20 862 Email: sales@bqtssolutions.co.uk GREA ATER ASIA BQT Solutions Singaporre Office SGX Centre 2, 4 Shenton Way, #14‐02 Singaapore 068807 Phon ne: +65 6220 7970 Fax: +65 6220 7656 Email: Rlee@bqtsolutio ons.com Copyright © 2011 BQT Solutions Limited. BQT B Solutions and the BQT solutio ons logo are registered trademarkks of BQT Solutions (Australia) Ptyy Ltd. M ni Seriees Min BM6 684 BM6 686 INSTA ALLATION GUIDEE Version1.0 Installation External Use • Make sure the wire bundle to the reader has an IP rating of at least IP65 Disassemble Handling 1. Use fingers to squeeze the reader cover • Handle the reader with care. DO NOT damage or drop unit before installation. This will void the warranty. • The reader will not be waterproof if the casing is damaged. Maintenance • Once installed the reader requires no maintenance. Troubleshooting 2. Problem Power on reader – reader does not start up Troubleshooting steps 1. Check connections 2. Check the voltage at the reader 3. Check the current capability of the power supply Power on reader – reader keeps beeping 1. Check buzzer line 2. Check the voltage at the reader 3. Check the current capability of the power supply Power on reader – LED keeps green Present a card to reader – a beep is heard but reader does not output any data 1. Check LED line Pull the cover from the top of reader Note: DO NOT use a screw driver or other implement to remove cover Mounting 1. If necessary, use the drilling template provided to drill holes. 2. The mounting screw size is #3 gauge. Note: Be careful of cables when drilling Wire connection Note: Power to the unit is provided from the listed control unit or from a separately UL listed 12V DC power‐limited, access control power source. DO NOT supply power during installation. Wiring methods shall be in accordance with the National Electrical Code, ANSI/NFPA70 Check your circuit diagram for the colour coding of the circuit wiring. The reader can be damaged beyond repair if the wiring is connected incorrectly. This will void the warranty. 1. Connect the 0V wire to the power 0V line; Note: The 0V line of all power supplies must be connected to a common 0V reference point. 2. Connect the Wiegand data wires; 3. Connect the Buzzer and LED wires; 4. Connect 12V DC wire; 5. Place reader on the wall (Make sure the wires are not crushed. This will void the warranty of damage occurs) 6. Insert and hand tighten the screws; 7. Check that the reader is level before tightening the screws; Note: Excessive tightening of screws may deform the casing, resulting in a damaged unit. This will void the warranty. 8. Turn on the 12V DC power to power up reader. 9. Allow 5 – 10 seconds for reader to finish initialization (depends on the application). Make sure reader is functioning correctly according to the application specification. Cover After checking reader function, attach front cover back to the reader 1. Align the bottom of front cover with the bottom of reader; Note: Make sure LED is aligned to the LED hole on the cover; 2. Push the cover onto reader and a click sound can be heard. Present a card to reader – no response from reader 1. Check whether the card has data encoded 2. Check the wiegand connection to controller 3. Check the voltage level on wiegand data lines 1. Try a known working card 2. Check if the reader requires to be configured with a configuration card If the problem still persists, please contact your distributor for technical support. Warranty Unless specified otherwise, the Company warrants to the Customer that’ BQT Solutions Branded Products’ (excluding third party products and software) are covered by a return to base warranty on defects in materials and workmanship affecting normal use for a period of 5 years from BQT invoice date (‘Standard Warranty’) This standard warranty does not cover damage, fault, failure or malfunction due to external causes including; accident, misuse, problems with electrical power, servicing not authorised by the Company, usage and or storage and/or installation not in accordance with Product instructions, failure to perform required preventative maintenance, normal wear and tear, act of God, fire, flood, war, any violent or similar occurrence; any attempt by any person other than Company personnel or any person authorised by the Company to repair or support the Products and problems caused by use of parts and components not supplied by the Company. The standard warranty does not cover any items that are in one or more of the following categories: software; external devices; accessories or parts added to the product after the product has been shipped from BQT Solutions. During the warranty, period beginning on the invoice date, the Company will repair or replace faulty products (at its absolute discretion) returned to its’ factory. The Customer must prepay shipping and transportation costs and insure the shipment or accept the risk of loss or damage during such transportation. The Customer shall be solely responsible for determining suitability for use and the Company will, in no event, be liable in this respect. This standard warranty is given in place of all warranties, conditions, terms, undertakings and obligations implied by statute, common law, trade usage, and course of dealing or otherwise including warranties or conditions of merchantability, fitness for purpose, satisfactory quality and / or compliance with description, all of which are hereby excluded to the fullest extent permitted by law.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2011:05:13 19:30:25+10:00 Create Date : 2011:05:13 19:30:25+10:00 Format : application/pdf Title : Microsoft Word - BQT Mini Series Installation Guide.docx Creator : WZhang Document ID : uuid:4e2d174d-92ea-4c07-82ad-80da40318876 Instance ID : uuid:e0cbb59f-1c8f-412a-91a1-81b37f2af708 Page Count : 2 Author : WZhangEXIF Metadata provided by EXIF.tools