BQT Solutions BT900A CONTACTLESS SMARTCARD READER User Manual

BQT Solutions (Australia) Pty Ltd CONTACTLESS SMARTCARD READER USERS MANUAL

a href="https://usermanual.wiki/BQT-Solutions" itemprop="url"> BQT Solutions >

USERS MANUAL

Page 1 of 3 EMC TechnologiesABN 82 057 105 549 Unit 3/87 Station Road Seven Hills NSW 2147 Au Telephone +61 2 9624Facsimile +61 2 9838Email syd@emctechwww.emctech.com.au Melbourne 57 Assembly Drive Tullamarine Vic 3043 Tel: +61 3 9335 3333 Fax: +61 3 9338 9260 Sydney Unit 3/87 Station Road Seven Hills NSW 2147 Tel: +61 2 9624 2777 Fax: +61 2 9838 4050 Brisbane 1/15 Success Street Acacia Ridge Qld 4110 Tel: +61 7 3875 2455 Fax: +61 7 3875 2466 Auckland (NZ) 47 MacKelvie Street Grey Lynn Auckland Tel: +64 9 360 0862 Fax: +64 9 360 0861 APPENDIX L OF TEST REPORT T 60822_F USER MANUAL FCC ID: QVL-BT900A Manufacturer: BQT Solutions (Australia) Pty Ltd Test Sample: Contactless Smart Card Reader Model: BT900-WG Serial Number: None Date: 4th September 2006
9 series_v2.9 Sep06 Drilling Template Copyright © 2006 BQT Solutions Limited. BQT Solutions and the BQT Solutions logo are registered trademarks of BQT Solutions (Australia) Pty Ltd. Mifare is a registered trademark of Philips Electronics. Specifications Output protocols Wiegand 26-199 bit, RS485 or custom configurations (model dependent) Power requirements 12Vdc Current consumption Normal 120mA Activated 140mA Read range 20 - 60mm (0.8” – 2.4”)(typically) Operating temperature -25ºC to +65ºC (-13ºF to 149ºF) Relative humidity 90% max, operating non-condensing Reader dimensions 140mm (L) x 45mm (W) x 32mm (D) (5.51” x 1.77” x 1.26”) Status LED’s Green & Red Audible tone Internal or external buzzer control Colour Two toned – Silver & Charcoal IP rating IP 67 Information contained in this document is subject to change without notice. For further technical information visit our website at www.bqtsolutions.com or email techsupport@bqtsolutions.com. Alternatively contact us at one of our global locations UNITED KINGDOM & EMEA Global House, 1 Ashley Avenue, Epsom Surrey KT 18 5AD United Kingdom Phone: + 44 (0)20 8823 9350 Fax: + 44 (0)20 8823 9001 AMERICA 30021 Tomas Street, Suite 300 Rancho Santa Margarita CA 92688 United States of America Phone: +1 877 278 2637 (ext 42) Fax:+1 877 278 2637 AUSTRALIA & ASIA PACIFIC Level 4, 65 Epping Road North Ryde NSW 2113 Australia Phone: +61 (0)2 8817 2800 Fax: +61 (0)2 8817 2811 CHINA Suite 1602, No.75, ShengDa Garden, 2518 LongHua Road, XuHui District, Shanghai 200232, P.R.China Tel: +86-21-5407 3638 Fax: +86-21-5407 3738 DF900 - DESFire BT900 - Mifare miP9 - SPEK CSN9 - Card Serial Number miPASS 9 Series Mifare reader models For all 9 Series readers ● 20mm (0.79”) diameter hole for wire entry ● 2 x 4 mm (0.16”) diameter holes for mounting screws ● Minimum reader dimensions are 140mm x 45 mm (5.51" x 1.77") INSTALLATION GUIDE Version 2.9Regulatory InformationCE MarkThe 9 Series has passed all relevant tests and obtained CE approval. C TickThe 9 Series has passed all relevant requirements for application of C Tick.FCCThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.BT900D, BT900DG, DF990D, DF900DG FCC ID: QVL - BT900PBT900WG FCC ID: QVL -BT900AmiP9, CSN9, BT900W FCC ID: QVL MIP9NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna- Increase the separation between the equipment and receiver- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected- Consult the dealer or an experienced radio/TV technician for helpAny changes or modifications not expressively approved by BQT Solutions could void the user's authority to operate this equipment. Designed & Manufactured in AustraliaNOTE:  The 0V reference cable shall be included within the controller cable.  The 12Vdc power cable shall NOT be included in the controller Cable.  Only ONE power source is connected from the reader at any one time.  RS485 - OPTIONAL USE 45mm 62mm ➣ ➣ ➣ ➣ 20mm Ø 4mm Ø 4mm Ø Wiring Schematic Reader connectionsBUZLEDW0W1+12Vdc 0VPower CableController CableRED +12VdcBLACK 0VYELLOW BUZORANGE LEDGREEN W0WHITE W1YELLOW/WGREEN/WBT900W, BT900WGmiP9, CSN9RS485ARS485BPower SupplyControllerNOTE: If used with a shielded cable, the shield is connected to Controller 0V referenceDF900D, DF900DG, BT900D, BT900DG0V9 series_v2.9.ai 21/09/2006 10:26:36 AM
Download:
Mirror Download [FCC.gov]
Document ID718214
Application IDyBOSlM8stioLr+LYkhY5Ug==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize11kB (137529 bits)
Date Submitted2006-10-20 00:00:00
Date Available2006-10-25 00:00:00
Creation Date2006-09-27 11:29:28
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2006-10-17 10:07:22
Document TitleMicrosoft Word - APPENDIX L_User Manual T60822_f.doc
Document CreatorPScript5.dll Version 5.2
Document Author: Les Dickenson
FCC ID Filing: QVL-BT900A

Navigation menu