BRAVEN LC BSOLO Bluetooth Speaker User Manual User Guide

BRAVEN LC Bluetooth Speaker User Guide

User Guide

USER GUIDE
ENGLISH | 2GET TO KNOW YOUR BRAVENPOWER ON / OFFPLAY / PAUSEBLUETOOTH PAIRINGANSWER / END CALL / VOICE CONTROLI/O PORT COVER (Seal tightly for waterproofing)VOLUME DOWN, SKIP BACK (press and hold)M I C R O - U S B CHARGING PORTV O L U M E U P , SKIP TRACK (press and hold)3 . 5 M M AUDIO-IN JACKEXTERNAL USB CHARGING PORTRESET BUTTONBATTERY CHECK BUTTON
ENGLISH | 3POWER & BLUETOOTH PAIRINGCHARGING YOUR BRAVEN1. Press the Power button for 2-3 seconds to turn your BRAVEN READY SOLO™ on or off. 2. Activate / enable Bluetooth® on your device’s settings.3. Speaker automatically enters pairing mode upon powering on. To pair a second device, press and hold the Bluetooth button. Go to your phone or device’s Bluetooth® settings and select “BRAVEN READY SOLO” from the list.4. Enter “0000” if asked for a pass code.Your BRAVEN will remember the last 8 devices it has paired with.NOTE: If your BRAVEN does not have an active Bluetooth® connection and is left on, it automatically powers off after 30 minutes. To restart your BRAVEN you will need to press and hold the power button for 2-3 seconds.• Before using your BRAVEN for the first time, charge the unit until the battery indicator light turns off. • To charge your BRAVEN, plug the included Micro-USB cable into a wall power adapter (not included) or into a powered USB port on a computer. Plug the Micro-USB connector end of the cable into the BRAVEN charging port. • Once fully charged, your BRAVEN READY SOLO™ has 12 hours of playtime at medium volume.
ENGLISH | 4CHARGING EXTERNAL DEVICESSPEAKERPHONEYour BRAVEN is designed to charge USB devices that draw from 0.3A - 1A using the full-sized USB port located behind the I/O port cover. To use external charging:1. Turn your BRAVEN on.2. Plug the Micro USB power cable that came with your phone, mp3 player, or other mobile device into the USB port on your BRAVEN. 3. Plug the other end of the cable into your mobile device, and it will immediately begin charging. Press the Mic button button on your BRAVEN to answer the call over the speaker. Press the Play / Pause Mic button again to end the call.WATERPROOF FEATURESThe BRAVEN READY SOLO™ is IP68 waterproof, and is designed to withstand rainfall, waterjets, water splashing, or a dunk in the pool. IMPORTANT: To ensure your BRAVEN READY SOLO™ speaker is prepared for use in a wet environment, remove all cable connections and tightly close the I/O port cover on the back of the speaker. If this cover is not securely fastened to the speaker, BRAVEN READY SOLO™ will not be waterproof.USING BRAVEN VOICE CONTROLTo activate Siri or Google Commands with your BRAVEN, short press the Mic button. You can now say commands through your BRAVEN, with your phone at a distance.
ENGLISH | 5USING TRUEWIRELESS STEREOPAIRINGRESETTING YOUR BRAVENUSING THE ACTION MOUNT TrueWireless allows you to wirelessly pair two BRAVEN READY SOLO™ speakers in right & left channel audio. To activate TrueWireless, long press the “battery check button” on the back of both speakers at the same time until a pairing chime emits. Within 30 seconds, a beep will indicate that both speaker have successfully paired. To reset your BRAVEN READY SOLO™ to factory settings, press the Reset button located on the back of your speaker. The included Action Mount allows you to attach your BRAVEN READY SOLO to most GoPro™ mounting systems. To attach the Action Mount to the READY SOLO, align the mount with the holes on the bottom of your BRAVEN. Secure the mount using the included screws and hex wrench.
ENGLISH | 6WARNINGS, CAUTION & LEGAL INFORMATION To reduce the risk of fire or electric shock, do not expose the BRAVEN to rain or moisture while charging. The BRAVEN should not be exposed to dripping or splashing, and objects filled with liquids, such as vases, should not be placed on or near it while being charged or charging other devices. As with any electronic products, use care not to spill liquids into any part of the product. Liquids can cause a failure and/or a fire hazard. The power supply must be used indoors only. Make no modifications to the product or accessories. Unauthorized alterations may compromise safety, regulatory compliance, and system performance, and will void the warranty. Do not place any flame sources, such as lighted candles, on or near the BRAVEN. The BRAVEN contains small parts that may be a choking hazard and is not suitable for children under age 3. Do not continue charging the battery if it does not reach full charge within the specified charging time. Overcharging may cause the battery to become hot, rupture, or ignite. If you see any heat deformation or leakage, properly dispose of the battery. Do not attempt to charge the battery in temperatures outside the range of 32°-104°F (0°-40°C). If the battery begins to leak, do not allow the liquid to come in contact with your skin or eyes. If contact has been made, wash the affected area with plenty of water and seek medical attention immediately. Do not expose the product or battery to excessive heat, including direct sunlight or fire and storage or use inside cars in hot weather, where it can be exposed to temperatures in excess of 115°F (60°C). Doing so may cause the battery and power supply to generate heat, rupture, or ignite. Using the product in this manner also may result in a loss of performance and a shortened life expectancy. Extended exposure to direct sunlight may damage the external appearance and material qualities. Do not step on, throw, or drop batteries or the power supply or device, or expose them to a strong shock. Do not pierce, crush, dent, or deform the batteries or power supply in any way. If either becomes deformed, properly dispose of it. Do not short-circuit batteries. Do not attempt to service the BRAVEN yourself. Opening or removing covers may expose you to dangerous voltages or other hazards and will void the manufacturer’s warranty. To prevent risk of fire or electric shock, avoid overloading wall outlets, extension cords, or integral convenience receptacles. Your Bluetooth device (mobile phone, music player, tablet, laptop, etc.) must support the A2DP Bluetooth profile in order to work wirelessly with your new BRAVEN speaker. The A2DP profile is supported by most recent mobile products with built-in Bluetooth capability. Please refer to your device’s user manual for details and instruction regarding the Bluetooth profiles it supports. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC RADIATION EXPOSURE STATEMENT: This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.Lithium Battery installed is not intended to be replaced by the USER. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.Where the MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. This product complies with California Energy Commission efficiency standards for consumer battery chargers. Hereby, Braven, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EUOperating Frequency Band: 2402 MHz to 2480 MHz Maximum RF power: 6dBm EIRPBraven hereby declares that READY SOLO is in compliance with Radio Equipment Directive 2014/53/EU.The full text of the EU DoC is available at the following: https://www.braven.com/eu-declaration-of-conformity/*****.PDFBraven follows Safety Instruction for CE-LV. Operate Products not more than -5~40 °C.Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventilation conditions. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.WARNING：To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus.WARNING: The power adapter is used as disconnect device, the disconnect device shall remain readily operable.WARNING：Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus.CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. The battery (battery or batteries of battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.Article 102. Manufacturers shall ensure that radio equipment shall be so constructed that it can be operated in at least one Member State without infringing applicable requirements on the use of radio spectrum.10. In cases of restrictions on putting into service or of requirements for authorisation of use, information available on the packaging shall allow the identification of the Member States or the geographical area within a Member State where restrictions on putting into service or requirements for authorization of use exist. Such information shall be completed in the instructions accompanying the radio equipment. The Commission may adopt implementing acts specifying how to present that information. Those implementing acts shall be adopted in accordance with the advisory procedure referred to in Article 45(2). Manufacturer: Braven LC.
󵶎󰽥󰶦󳛒 | 7󴦠󴧅󲼭󹄶󱙭󹀺󴕿󱋎󹄶󰶦󹄎󴘫󴉢 󴊐󴛹󹑳󴍂󶰄󵇕󴓊󰽥󴘬󴶠󰽥󱋎󹄶󰶦󱋎󹄶󰶦󰵴󸑛󶔨󰺮󹄶󲒩󷢢󱡸󱝛󳸬󷢢󱡸󸛈󱐔󴓊 󰽥 󴎤 󲼑 󴓊󰽥󳙧󹁻󴦠󴧅󱙭󹀺󲮸󸁰󱜴󶡊󲶎 󹄶󴙂󲚋󱌼󰾫󵈾󲳴󷦳 󷢢󱡸󰺱󲚪󱡸󳙖 󸔢  󷫪 󱜴   󳙖 󸔢  󲔝 󱌌 󲶎 󴎁 󰻁 󹌬 󲔛   󲶎󶡊󳐧󱜴󶡊󲶎󱁃󷫿󴬁󱔭    󳟈     󴧧 󴙂󰵴󸑛󶔨󰶺󰸫󱎸󲘱󴦠󴧇󳃵󷩘󵉐󵒹󱙭󹀘󼵼󷸽󱖢󱲉󱋎󵉐󳞟󲘜󳣑󹆫󱲉󹄎󰶦󳃵󴟑󴘫󴾡󱺯󰶦󰵷󲪿󳣑󹆫󰸶󴛹󴊐󳃵󹑸󴘲󼵼󱋎󴛙󴓊󰽥󵒹󴶠󱡸󼵸󲁵󶰄󵇕󼵹󰵷󲪿󳙞󶔨󱲉󱌧󰵴󳃵󸿢󸑛󼵼󱝛󳞟󲘆󱌧󰺮󷸄󱾋󸑴󷝥󱋎󵉐󳃵󱋎󵉐 󰵸󰻤󰽧󵉐󲒩󰹢󱡸󰵨󳭌󼵼󷸽󴎤󲼑󰵷󷦳󲘜󴓊󰽥󴘲󱌆󰹢󱡸󵒹󰻤󰽧󸛈󱐔 󴓊󰽥󰼔󲘌󶩝󳙧󹁻󱠥󳃵󴦠󴧇 󵉐󴙂󲳴󹏣󱲉󲕔󱌼󰾫󵈾 󰵷󷦳󲘆󰹢󱡸󳃵󸿢󰻞󸑴󷝥󰻤󰽧󱁝󳙖 󳦣󶑒󳍈󳧉󵒹󳥀󳙖󱜴󶡊󰼔󱙭󱛺󲔝󱌌󲶎󼵼󱝖󷨟󲶎󱠥󶂹󶑢󲶎󶡊󼵼󲪇󲘜󲘌󶩝󱁃󱁝󱿠󳙪 󰵷󷦳󱲉󰵴󳃵󸿢󸑛󳙞󶔨󰻤󰽧󴦠󴬞󴙂󼵼󲁵󴩀󴱍󵒹󷕚󴩿󼬣󻱻󽴔 󺕧󽴔 󺃟󻳓󻰧󽴔 󻯓󼪧󻰓󽴔 󻷓󻱃󺳳󺽃󽴔 󼉸󻳓󻷠󻪟 󻰓󽴔 󻌓󺕧󽴔 󻞄󺋿󻪟󽴔 󺙇󼉫󻞫󼕳󻺏󺺗󻞼󻞫󻫳󻰏󽴔󻀋󻃸󻮇󻱃󺕧󽴔󻀋󽴔󼝏󺌏󻪟󺙇󼉫󺣧󻪃󻗫󺝣󽴔 󻨗󺣧󺼿󽴔 󺐒󻆠󺇋󽴔 󺃨󻰏󽴔 󻨰󼆃󺴫󼄓󻮛󻺓󽴔 󻀋󺅃󻰏󽴔 󺞳󺹇󽴔 󻱴󼌧󺹋󽴔 󼉸󻳓󼨧󺄿󺕧󼉸󻳓󼨧󺝣󽴔 󺢨󻨗󽴔 󺋇󽴔 󻯓󻪟󽴔 󺫟󺝣󽴔 󺃏󺌛󻱃󻪟󺤟󻪃󻗫󺝣󽴔 󻨗󺣸󺞗󺞳 󺞳󺹇󽴔 󻳓󻱟󽴔 󻳫󼥗󺇋󺺗󼃻󺃏󻺏󺴫󽴔󻳫󼥗󻰧󽴔󻪃󺩳󽴔󻉏󻉓󻪟󺢓󽴔󻨰󼆃󺹋󽴔󻪝󻺏󺹃󻺏󽴔󻨙󺢓󺴬󻷋󻰧󼨧󻞼󻞫󻫳󻨰󼆃󺝣󽴔󺆯󻱴󽴔󻃞󺫟󺝣󽴔󼬣󻱻󽴔󻯓󼪧󻰓󽴔󼇗󺱧󼨯󽴔󻛧󽴔󻱗󻞄󺞗󺞳󻳓󻮟󺇄󺋘󽴔 󻱴󼌧󺝣󽴔 󻞳󺖃󻪟󻗫󺺛󽴔 󻕻󻭸󼩃󻩋󼨸󺞗󺞳󻳫󼥗󻱃󺕧󽴔 󻨰󻘇󻗫󺹻󺹋󽴔 󺃫󻴿󼨧󻺏󽴔 󺺗󻞼󻞫󻫳󻱇󻹬󺣧󻺏󽴔 󻨙󻰏󽴔 󻆏󺆌󻰏󽴔 󻨗󻳓 󺊫󻳤󽴔 󻷏󻛧󽴔 󻃞󻞫󻝳󼘫󽴔 󻘀󺝴󻰓󽴔 󻳏󼨧󻞫󼕻󽴔 󻛧󽴔 󻱗󻰋󺼿󽴔 󻇃󻹬󻰓󻀃󼭷󼬣󼨸󺞗󺞳 󻃬󺅛󽴔 󻌪󺕫󽴔 󻩠󼇗󻬏󽴔 󺃨󻰏󽴔 󻉗󺐒󻙛󻝳󺹋󺫟󺝣󽴔󺋋󼅧󻪟󽴔󺤟󻺏󽴔󺺗󻞼󻞫󻫳󷵩󱟈󴎤󲼑󴎁󵒹󲺕󱸡󷵩 󱟈 󼵼󲘮 󲳱 󱠥 󴎁 󲲓 󱁌 󲸂󺆌󺆯󻷋󻰧󽴔󻃞󽴔󻅤󻳐󽴔󻳤󻇃󳄲󼵸󳈄󶇳󼵹󹌉󸢁󱎸󲘮󼵼󸄦󱰑󼵸󳉽󰽞󼵹󻇋󺸷󽴔󺞳󻮃󺅃󺗗󽴔󺮿󺋿󽴔󺥳󺴫󺌇󺅛󽴔󺛓󺹃󺋿󴎤󼶊󳥤󱔭󳍹󶇳󱐔󲲔󶩉󱕜󵒹󱍅󸁰󱕜󹄶󴙂󳈄󲳴󷦳   󱐲󰾫 󵈾󱑹 󱋎󹄶󱋎󹄶1.      2. 󴎤󲼑󼶊󲁵󳩔󲹠󵒹󴌵󳥤󴐟󱔔󵒹󷂱󴶄󸑷󳍹󲪇󰶃󲦻󶑒󳅨󲮔󼵼󲔐󲘜󱲉󱐔󸷧󱝟󱌢󸽼󷦳󸡿󳜝󱞗󱔔󼵼󲹠󹄾󷦳󳉽󰽞󵉐󴙂 󱲉󲹠󵳦󰵨󴂃󰾫󵈾󰷓󱑹󼵼 󱋎󵉐󱙁󱋌󵕬󱑌󵉐󴋒1. 󳉸󵤚󴦨2. 󱌢󳍉󼄇󺆯󻪟󽴔󼬫󻘀󻪿󺅿󻱃󻪕󺆯󽴔󼏫󻴇󽴔󻱗󻰋󺽃󻉓󼮓󻪟󽴔󻱟󺢨󻰋󺴫󽴔󺎋󻺠󺞗󺞳󻰓󽴔󺞳󻞫󽴔󻞫󻱠󼨧󺳳󺽃󽴔󻳓󻮟󻰓󽴔󺌇󺅛󺛛󺲻󻩋󼨸󺞗󺞳 󻰓󽴔󼅧󻰛󽴔󻕻󻭸󼨧󺋿󽴔󻳓󻪟 󻃿󼗿󺹻󺃏󽴔󼉸󻳓󽴔󺣯󽴔󺨛󺌛󻺏󽴔󻱴󼌧󺹋󽴔󼉸󻳓󼨧󻞼󻞫󻫳1. 󼤫󻞫󽴔󺧀2. 󺔓󺞳CHINESEJAPANESEKOREAN
PHONE: 1-877-9 BRAVEN (1-877-927-2836)REGISTER: braven.com/registerSUPPORT: braven.com/supportONLINE: braven.comEMAIL: support@braven.comv02

Navigation menu