BUFFALO 09102026-0 AirStation Wireless-N NFINITI HighPower Keychain USB2.0 Adapter User Manual

BUFFALO INC. AirStation Wireless-N NFINITI HighPower Keychain USB2.0 Adapter

User manual

v1.0User ManualAirStation Wireless-N HighPoweriDraft-N KeyChain USB2.0 AdapterWLI-UC-G300HP
2• Don’t plug in your wireless USB client yet! Install the drivers rst.• Insert the AirNavigator CD into the CD-ROM drive of your computer. The AirNavigator Setup Wizard should launch automatically. • To launch the AirNavigator Setup Wizard manually, click Start, then Run. Type “D:\AirNavi.exe”, where D is the drive letter assigned to your CDrom. • Click OK to launch the wizard. Getting Started
3• Click on Begin Installation. Installing Drivers
4• Click AirStation Wireless LAN Adapters.• If you are running a software firewall, disable it. Click Next. • Installation of the Buffalo Wireless Client Manager is optional. Check Install Wireless Client Manager to install it now. You can install it later if desired; see page 6.• Click Install.Installing Drivers
5• Review the license agreement. Select Agree and click Next to continue installation.• Plug your AirStation Nfiniti into a USB port on your computer.• When the Wireless USB Adapter is successfully installed, click Finish. If you’re not installing Client Manager, turn to page 11.Installing Drivers
6Client Manager can be used to survey and connect to available access points, congure WPA/WEP encryption, and create connection proles.Note: When the Buffalo Client Manager is installed, the client manager built-in to Windows is automatically disabled.Installing Client ManagerIf you didn’t check the Client Manager install box on page 4, you’ll have to rerun installation to install Client Manager. Insert the AirNavigator CD into the CD-ROM drive of you computer. If the Air Navigator Setup Wizard does not launch automatically, launch it manually by clicking Start and then Run. Enter D:\AirNavi.exe in the dialog box that appears. Click OK. Select Begin Installation.Client Manager
7Client Manager• Click AirStation Wireless LAN Adapters.• If you are running a software firewall, disable it. Click Next. • Put a check next to Install Wireless Client Manager. • Click Install.
8Client Manager• Driver installation will begin. If you’ve already installed drivers, click Cancel.• Client Manager installation will begin. Click Next. • Click Agree. • Click Next.
9Client Manager• Click OK when Client Manager installation is complete.
10• Click Check Internet Connection.This page will appear if an internet connection is detected. Click Close.Checking Internet Connection
11Connecting Wireless Clients to your NetworkBuffalo supports three different methods for connecting your wireless client device to your network.If your AP supports it, use the simple, utterly secure AOSS to connect. Install the Client Manager from your AirNavigator CD (page 6) and turn to page 12.You may also use the Client Manager software from your AirNavigator CD to configure your network manually. See page 15 for more on Client Manager.If you’re running Windows XP or Vista on your PC, you may use their built-in wireless tools to connect to your router/AP. See page 22 for more on XP or 26 for more on Vista.
12The AOSS button for this wireless client is in its Client Manager software. Start Client Manager by right clicking on the black antenna icon in your System Tray, or by launching the Client Manager from your Start Menu: Programs >> Buffalo >>AirStation Utility >> Client Manager.AOSS (AirStation One-Touch Secure System) is a simple, one-touch setup for connecting wireless clients to an access point while enforcing the most secure possible connection encryption type. Users no longer need to worry about choosing the proper security protocols, IP addresses, or SSID. AOSS determines the optimal connection and congures itself in seconds. If your router doesn’t support AOSS, turn to page 6 to congure your connection manually with Client Manager or Wireless Zero Cong.Using AOSS
13• From the Status Screen, select the Proles tab.• Click the blue AOSS button on the Client Manager’s screen. The AOSS wizard will appear. • Now, press the AOSS button on the Access Point. Hold it down until the AOSS LED begins to ash. Using AOSS
14Once AOSS is complete (about 30 seconds), the connection is archived as a prole for later use. To minimize Client Manager to the system tray, click the ‘X’ in the top right corner.Notes:AOSS will scan for an AOSS partner for about two minutes. If it times out before nding one, just press the AOSS buttons again.Output power is reduced to 25% of normal during AOSS for security reasons. If you’re having trouble making an AOSS connection, temporarily move the devices closer together.AOSS will automatically use the highest level of security available for all currently connected wireless devices. If you have trouble connecting with AOSS, temporarily disable all personal rewalls on your PC, such as ZoneAlarm or Microsoft Personal Firewall. These programs may be re-enabled after AOSS has nished.Using AOSS
15You may use Client Manager to congure your wireless network. Client Manager consists of the Status page, the Survey page, and the Proles page. You can access each page by clicking the corresponding button on Client Manager. In addition to these pages, several dialog boxes are also available. You can access the Edit Prole dialog box, New Prole dialog box, IP Conguration dialog box, or WEP Conguration dialog box using the Client Manager pages. You may also initiate AOSS.Status PageClick Status to open this page. By default, this page is displayed when you start Client Manager. Details of connection status are displayed.This page only displays connection information; no changes to settings are made here.This page includes the following components:• Adapter Name – Displays the part number of the wireless adaptor that is being used.Client Manager Conguration
16Client Manager Conguration• Network Type - Displays whether network is in Ad-Hoc or Infrastructure mode. • Rate – The speed of communication between wireless devices. If the Client Manager is not connected to a remote wireless device (access point or another client), no rate will be displayed.• Channel – The channel that the two wireless clients are using for communication. If the Client Manager is not connected to a remote wireless device, no channel will be displayed. Channels 1-11 may be used.• Security – The type of encryption in use. If the Client Manager is not connected to a remote wireless device, then ‘No Encryption’ will be displayed.• IP Address – The IP address of the machine the Client Manager is installed on. If the Client Manager is not connected to a network with DHCP, then no IP address will be displayed.• MAC Address – The MAC address of the wireless client device inside the computer Client Manager is installed on. If no wireless device is present in the computer, then no MAC Address will be displayed.• Signal Strength – Displays the signal strength of the peak signal level the wireless adapter receives from the wireless device to which it is connected. Next to the signal level is the wireless hardware being used for this measurement.
17Click the Scan tab to open this page. Here, you can survey the area, display available access points, and connect to available access points.This page includes the following components:• Wireless SSID – The SSID is the “name” of a wireless network. Each wireless device on a network must use identical SSIDs to successfully communicate. • Wireless Mode – Displays available modes for each available remote wireless device.• Strength – Displays the relative signal strength of the wireless networks.• Encryption – Displays whether the wireless network is using any sort of encryption.Click Connect to connect to a highlighted SSID, or Refresh to update the list of available wireless devices. Client Manager Conguration
18This dialog will open for you to enter any necessary encryption information. The correct encryption type should already be selected automatically in the Encryption Method drop down list. Only change this setting if necessary.The Encryption Key is where the actual key for the wireless network should be entered. Some wireless networks allow you to enter multiple keys; four separate elds are available for this. If your network only uses one encryption key, then please use the rst eld (#1) to enter your key.The Register Prole option will store this wireless network in your proles. You will then automatically connect to this network when inside its range. This is recommended if you plan on using this wireless network again.Press the Connect button once you have completed entering encryption information.Client Manager Conguration
19Proles PageClick the Proles tab to open this page. Use this page to access your proles. Proles allow you to save the information associated with a specic wireless network so you can quickly and easily connect to that network when you are in that location. The Proles page allows you to add, delete, and edit your proles, as well as import and export data.• Connect – Click the Connect button to connect to the selected prole and return to the Status page.• Edit – Click the Edit button to edit the selected prole’s settings. The Edit button also allows you to delete proles that are no longer used or required.• Add – Click the Add button to add a prole manually. You will need important information such as SSID, encryption settings, and network type.Client Manager Conguration
20New Prole Dialog Box• Select Prole – Select whether the prole is for a wireless or wired connection.• Prole Name – Enter the name you want to associate with the new prole.• Network Type – Select the network mode you want to associate with the new prole. Select Infrastructure if your network consists of both wired and wireless devices that communicate through a central device, such as an access point. Select Ad-hoc if your network consists of only wireless devices that communicate with each other directly.• Network Name SSID – Enter the SSID of your network. The SSID is the name of your wireless network. All wireless devices on a network must use identical SSIDs to successfully associate with other devices on the network. MYSSID is an example of a valid SSID. • Channel – The channel setting is only used for Ad-hoc connections. When using an Ad-hoc connection, select a channel and make sure the other Ad-hoc devices are congured to use the same channel. Otherwise, use Auto-Channel.• Encryption Method – Displays the types of encryption available. Once encryption is selected, you will be required to enter an Encryption Key. For the Transmission Key Number, 1 is recommended.• OK – Click OK to save your specications and return to the Proles page.Client Manager Conguration
21Advanced Prole Options• Network Tab – Displays the network information tab. A static IP can be specied for this wireless prole here. It is not recommended to change any of these settings unless specied by an administrator.• Browser Tab – Displays settings to change your browser preferences for this wireless prole. A specic home page can be specied when connected to this wireless prole as can specic proxy server addresses.• Printers Tab – Displays the printers tab. A specic default printer can be associated to this prole. Thus, when connected to this prole, a specic printer will be used as the default printer.• OK – Click the OK button to save your specications and return to the Proles page.• AOSS Icon – To automatically add the USB wireless client to your network, just click this icon and then hold down the AOSS button on your wireless router for a few seconds. Check your package for an AOSS Manual, which will give more information on using AOSS.Client Manager Conguration
22Windows XP includes the Zero Conguration Service, a built in service to congure your wireless clients from within Windows. Turn to page 6 if you would rather use Buffalo’s Client Manager to congure your wireless client.• If the Wireless Zero Configuration Service is activated, Windows will scan for available wireless access points once the Wireless USB Adapter is properly installed. If Windows detects one or more access points, a networking icon appears within the system tray. “One or more wireless networks are available” will appear as a caption accompanying the icon.• To start Wireless Zero Configuration manually, click Start >> Control Panel >> Administrative Tools >> Services. Select Automatic in the Startup Type field of Wireless Zero Configuration Service.• Right click the networking icon in the taskbar and select View Available Wireless Networks. Select an SSID and click Connect. You may need to check the box indicating you are connecting to an unsecured network. See page 23 if you need to enter an SSID network name or WEP/WPA encryption key.Zero Conguration Service
23• Click the Advanced tab to enter an SSID network name or WEP/WPA encryption key if necessary. To add an SSID network name that is not listed, click Add.Zero Conguration Service
24• To congure a WEP/WPA encryption key, select the wireless network and click Congure.• From the pull down menu, select the Network Authentication and Data Encryption types for the wireless network. Enter and conrm the Network Key and Key Index. Click OK when nished.Zero Conguration Service
25Wireless Zero CongurationWireless Zero Conguration Service (Windows XP)Windows XP offers the Wireless Zero Conguration Service to support 802.11b and 802.11g wireless networking. This service automatically polls the area for available wireless access points. If an available wireless access point is found, Windows attempts to connect to the access point. If no available wireless access points are found, you must manually add the access point information to connect (for example when the SSID is not broadcasted).Note: The Wireless Zero Conguration Service and Client Manager do not function properly together. If you want to use Client Manager, disable the Wireless Zero Conguration Service.Enabling the Wireless Zero Conguration ServiceClick Start >> Control Panel >> Administrative Tools >> Services to open the Services conguration window. Select Automatic in the Startup Type eld of Wireless Zero Conguration Service to enable the Wireless Zero Conguration Service and click apply.Note: The default Startup Type value of Wireless Zero Conguration Service is Automatic. Disabling the Wireless Zero Conguration ServiceClick Start >> Control Panel >> Administrative Tools >> Services to open the Services conguration window. Select Disabled in the Startup Type eld of Wireless Zero Conguration Service to disable the Wireless Zero Conguration Service.
26Windows Vista also includes a built in wireless client manager. You may use it to congure your Buffalo wireless client, or turn to page 6 if you would rather use Buffalo’s Client Manager to congure your wireless client.• Plug in your USB wireless client.• Click on the Network icon in the systray.• A list of available wireless networks will appear. Choose your desired wireless network’s SSID.Windows Vista
27• If your chosen wireless network is security enabled, enter the network security key or password.• Windows will now connect you to your wireless network.Windows Vista
28Antenna InformationThe WLI-UC-G300HP has three built-in antennas. External antennas cannot be attached to the WLI-UC-G300HP.
29SpecicationsWireless LAN Interface Standards Compliance Draft-N (802.11n Draft 2.0) IEEE 802.11g IEEE 802.11bCommunication Protocol Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division MultiplexingFrequency Range 2.412 - 2.462 GhzTransmission Rate Draft-N: Up to 300 Mbps (Auto) 802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps (Auto) 802.11b: 1, 2, 5.5, 11 Mbps (Auto)Access Mode Infrastructure ModeSecurity 128/64 Bit WEP, WPA-PSK (TKIP & AES), WPA2-PSKOtherInterface USB 2.0Environmental Operation 32º - 104º F (0º - 40º C) Relative Humidity 20 - 80 % (non-condensing)
30Troubleshooting / FAQWhat should I do if I already have a version of Client Manager on my PC? Update your Client Manager to the version on the CD. If you do not update your Client Manager, there could be a loss of functionally, as some older versions of Client Manager will not work properly with the G300N Wireless Notebook Adapter. Before updating Client Manager, uninstall any previous versions of Client Manager. To update your Client Manager, load the Air Navigator CD and select Install Client Manager. Proles can rst be exported from the Proles tab of Client Manager and then imported back into Client Manager after installation.Why won't Client Manager function properly? The Wireless Zero Conguration Service in Windows XP conicts with Client Manager. If you use Windows XP, make sure that the Wireless Zero Conguration Service is disabled. Click Start >> Control Panel >> Administrative Tools >> Services. Select Disabled in the Startup Type eld of Wireless Zero Conguration Service to enable the Wireless Zero Conguration Service. The default value of Wireless Zero Conguration Service is Automatic.I have more than one Air Navigator CD. Do I need more than one CD? No. The same Air Navigator CD works with all Buffalo Technology access points and wireless adapters. Please use the newest CD you have, with the highest revision number on it.
3110BaseT or 100BaseTX: 802.3 based Eth-ernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 10 is 10 Mbps and 100 is 100 Mbps. 802.1x: The standard for wireless LAN authentication used between an AP and a client. 802.1x with EAP will initiate key handling. Ad-Hoc Network: The wireless network based on a peer-to-peer communications session. Also referred to as Adhoc. Bandwidth: The transmission capacity of a computer or a communication channel, stated in Megabits per second (Mbps). BSS (Basic Service Set): An 802.11 net-working framework that includes an Access Point. Bus Mastering: A system in which the spec-ied Input/Output device (e.g. NIC Card) can perform tasks without the intervention of the CPU. Client: A PC or workstation on a network. Cross-Over Wiring: A UTP cable that has its transmit and receive pair crossed to allow communications between two devices. DCE (Data Communications Equipment): Hardware used for communication with a Data Terminal Equipment (DTE) device. Default Gateway: The IP Address of either the nearest router or server for the LAN. Default Parameter: Parameter set by the manufacturer. Destination Address: The address portion of a packet that identies the intended recipi-ent station. DHCP (Dynamic Host Conguration Protocol): Based on BOOTP, it uses a pool of IP addresses, which it assigns to each device connected to it, and retrieves the address when the device becomes dormant for a period of time. Glossary
32DNS (Domain Name System): System used to map readable machine names into IP addresses Driver: Software that interfaces a computer with a specic hardware device. DSSS (Direct Sequence Spread Spectrum): Method of spreading a wireless signal into wide frequency bandwidth. DTE (Data Terminal Equipment): Device that con10BaseT or 100BaseTx: 802.3 based Ethernet network that uses UTP (Unshield-ed twisted pair) cable and a star topology. 10 is 10 Mbps and 100 is 100 Mbps. DCE (Data Communications Equipment): Hardware used for communication with a Data Terminal Equipment (DTE) device. Default Gateway: The IP Address of either the nearest router or server for the LAN. Default Parameter: Parameter set by the manufacturer. Destination Address: The address portion of a packet that identies the intended recipient station. DHCP (Dynamic Host Conguration Protocol): Based on BOOTP, it uses a pool of IP addresses, which it assigns to each device connected to it, and retrieves the address when the device becomes dormant for a period of time. DNS (Domain Name System): System used to map readable machine names into IP addresses Driver: Software that interfaces a computer with a specic hardware device. DSSS (Direct Sequence Spread Spectrum): Method of spreading a wireless signal into wide frequency bandwidth. DTE (Data Terminal Equipment): Device that controls data owing to and from a computer. Glossary
33Dynamic IP Address: An IP address that is automatically assigned to a client station in a TCP/IP network, typically by a DHCP server. ESS (Extended Service Set): A set of two or more BSSs that form a single sub-network. ESS-ID is user identication used in the ESS LAN conguration. Ethernet: The most widely used architecture for Local Area Networks (LANs). It is a shared-media network architecture. The IEEE 802.3 standard details its functionality. Ethernet cable: A wire similar to telephone cable that carries signals between Ethernet devices. File and Print Sharing: A Microsoft applica-tion that allows computers on a network to share les and printers. Firmware: Programming inserted into programmable read-only memory, thus becoming a permanent part of a computing device. Frame: A xed block of data, transmitted as a single entity. Also referred to as packet. Full-Duplex: To transmit on the same channel in both directions simultaneously. Gbps (Giga Bits per second): One billion bits per second. Half-duplex: To transmit on the same channel in both directions, one direction at a time. Hub: A device which allows connection of computers and other devices to form a LAN. IEEE (Institute of Electrical and Electronics Engineers): The professional organization which promotes development of electronics technology. Glossary
34MAC (Medium Access Control) Address: A unique number that distinguishes network cards. Mbps (Mega Bits Per Second): A measurement of millions of bits per second. MDI/X (Media Dependent Interface/Cross-over): Port on a network hub or switch that crosses the incoming transmit lines with the outgoing receive lines. MHz (MegaHertz): One million cycles per second. MIB II: A database containing performance information and statistics on each device in a network. MIPS (Million Instructions Per Second): A measurement of processing speed. NAT (Network Address Translation): An internet standard that enables a LAN to use one set of IP addresses for internal trafc and a second set for external trafc. IP (Internet Protocol) Address: A unique 32-binary-digit number that identies each sender or receiver of information sent in packets. Infrastructure: A wireless network or other small network in which the wireless network devices are made a part of the network through the Access Point. ISP (Internet Service Provider): A company that provides access to the Internet and other related services. IV (Initialization Vector): The header section of a message packet. LAN (Local Area Network): A group of com-puters and peripheral devices connected to share resources. LED (Light Emitting Diode): The lights on a hardware device representing the activity through the ports. Glossary
35NIC (Network Interface Card): An expansion card connected to a computer so the computer can be connected to a network. Packet: A block of data that is transferred as a single unit, also called a frame or a block. Packet Filtering: Discarding unwanted network trafc based on its originating address or its type. PCI (Peripheral Component Interconnect): A bus that is connected directly to the CPU. PCMCIA (Personal Computer Memory Card International Association) Card: Removable module that adds features to a portable computer. Ping (Packet Internet Groper): An Internet utility used to determine whether a particular IP address is online. Plug and Play: Hardware that, once installed (“plugged in”), can immediately be used (“played”), as opposed to hardware that requires manual conguration. PoE (Power over Ethernet): A mechanism to send DC power to a device using a CAT5 Ethernet cable. PPPoE (Point-to-Point Protocol over Ethernet): A specication for connecting users on an Ethernet line to the Internet through a common broadband medium. Protocol: A standard way of exchanging information between computers. RADIUS (Remote Authentication Dial In User Service): A server that issues authentication key to clients. RAM (Random Access Memory): Non-permanent memory. Glossary
36Repeater Hub: A device that collects, strengthens and transmits information to all connected devices, allowing the network to be extended to accommodate additional workstations. RC4: The encryption algorithm that is used in WEP. RJ-45 connector: An 8-pin connector used between a twisted pair cable and a data transmission device. ROM (Read Only Memory): Permanent memory. Router: Device that can connect individual LANs and remote sites to a server. Roaming: The ability to use a wireless device while moving from one access point to another without losing the connection. Script: A macro or batch le containing instructions and used by a computer to perform a task. Server: Any computer that makes les or peripheral devices available to users of the network and has a resident Network OS. SMTP (Simple Mail Transfer Protocol): The protocol used to dene and deliver electronic mail (E-mail) from one location to another. SNMP (Simple Network Management Protocol: An application layer protocol that outlines the formal structure for communication among network devices. Static IP Address: A permanent IP address is assigned to a node in a TCP/IP network. Also known as global IP. STP (Shielded Twisted Pair): Twisted Pair cable wrapped in a metal sheath to provide extra protection from external interfering signals. Subnet Mask: An eight-byte address divided into 4 parts separated by periods. Glossary
37TCP/IP (Transmission Control Protocol/Internet Protocol: Protocol used by computers when communicating across the Internet or Intranet. TFTP (Trivial File Transfer Protocol): Simple form of FTP (File Transfer Protocol), which Uses UDP (User Datagram Protocol), rather than TCP/IP for data transport and provides no security features. TKIP (Temporal Key Integrity Protocol): An encryption method replacing WEP. TKIP uses random IV and frequent key exchanges. Topology: The shape of a LAN (Local Area Network) or other communications system. Twisted Pair: Cable that comprises 2 or more pair of insulated wires twisted together. UDP (User Datagram Protocol): A communication method (protocol) that offers a limited amount of service when messages are exchanged between computers in a network. UDP is used as an alternative to TCP/IP. Uplink: Link to the next level up in a communication hierarchy. UTP (Unshielded Twisted Pair) cable: Two or more unshielded wires twisted together to form a cable. WAN (Wide Area Network): A networking system covering a wide geographical area. WEP (Wired Equivalent Privacy): An encryption method based on 64 or 128-bit algorithm. Web Browser: A software program that allows viewing of web pages. Wi-Fi (Wireless Fidelity): An organization that tests and assures interoperability among WLAN devices. Glossary
38Wire Speed: The maximum speed at which a given packet can be transferred using Ethernet and Fast Ethernet standard specications. WLAN (Wireless LAN): A LAN topology using wireless devices. VPN (Virtual Private Network): A security method to connect remote LAN users to a corporate LAN system.Glossary
39Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC / CE / R&TTE
40IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.SAR compliance has been established in typical laptop computer(s) with USB slot, and product could be used in typical laptop computer with USB slot. Other application like handheld PC or similar device has not been veried and may not compliance with related RF exposure rule and such use shall be prohibited.The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory to match the intended destination. The rmware setting is not accessible by the end user.Taiwan:SAR compliance has been established in typical laptop computer(s) with CardBus slot, and product could be used in typical laptop computer with CardBus slot. Other application like handheld PC or similar device has not been verified, may not comply with related RF exposure rules, and such use shall be prohibited. FCC / CE / R&TTE
41Europe - EU Declaration of Conformity:This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:-EN60950-1:2006Safety of Information Technology Equipment-EN 62311 : (2008)Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic elds (0 Hz – 300 GHz)-EN 300 328 V1.7.1: (2006-10)Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive-EN 301 489-1 V1.8.1: (2008-04)Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements-EN 301 489-17 V1.3.2 (2008-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for 2,4 GHz wideband transmission systems, 5 GHz high performance RLAN equipment and 5,8 GHz Broadband Data Transmitting SystemsFCC / CE / R&TTE
42This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.FCC / CE / R&TTE
43FCC / CE / R&TTE
44FCC / CE / R&TTE
45FCC / CE / R&TTE
46Warranty InformationBuffalo wireless products come with a 2-year limited warranty from the date of purchase. Buffalo Technology warrants products in good operating condition for the warranty period. This warranty does not include non-Buffalo Technology installed components. If the Buffalo product malfunctions during the warranty period, Buffalo Technology will, at its discretion, repair or replace the product at no charge, provided the product has not been subjected to misuse, abuse or non-Buffalo Technology authorized alterations, modications, or repairs. When returning a product, include your original proof of purchase. Return requests cannot be processed without proof of purchase. Shipment of returned product to Buffalo Technology is the responsibility of the purchaser. All expressed and implied warranties for the Buffalo product line including, but not limited to, the warranties of merchantability and tness for a particular purpose, are limited in duration to the above period.Under no circumstances shall Buffalo Technology be liable in any way to the user for damages, including any lost prots, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, the Buffalo products.Buffalo Technology reserves the right to revise or update its products, software, or documentation without obligation to notify any individual or entity.Please have your proof of purchase receipt to get warranty support. All defective products shall be returned with a copy of proof of purchase.In no event shall Buffalo Technology’s liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. Buffalo Technology does not offer refunds for any product.
47Contact InformationNorth America (USA / Canada) Buffalo Technology (USA), Inc.11100 Metric Blvd, Suite 750Austin, TX 78758-4018GENERAL INQUIRIESMonday through Friday 8:30am-5:30pm CSTDirect: 512-794-8533Toll-free: 800-456-9799 Fax: 512-794-8520Email: sales@buffalotech.comTECHNICAL SUPPORTNorth American Technical Support by phone is available 24 hours a day, 7 days a week. (USA and Canada). Toll-free: (866) 752-6210 Email: info@buffalotech.com
48Contact InformationEurope Buffalo Technology UK LTD176, Buckingham Avenue,Slough, Berkshire, SL1 4RDUnited KingdomGENERAL INQUIRIESE-mail: sales@buffalo-technology.comTECHNICAL SUPPORTPhone (UK only): 08712 50 12 60*Phone: +353 61 70 80 50Email: helpdesk@buffalo-technology.ie*Calls cost 8.5p per minuteTechnical Support Operating HoursMonday - Friday (GMT)9:00 AM - 6:00 PM Monday-Thursday9:00 AM - 4:30 PM FridayAt Buffalo Technology, we constantly update our software and rmware. For the most recent software, rmware, driver, and technical whitepaper releases available, please visit the Buffalo Technology website: www.buffalotech.com.

Navigation menu