Badger Meter 2018HHMESE ORION ME/SE Handheld Module User Manual Exhibit D Users Manual per 2 1033 b3

Download:
Mirror Download [FCC.gov]
Document ID	3844377
Application ID	78A5ckjLlWXtqIrdvRUxoQ==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	124.59kB (1557426 bits)
Date Submitted	2018-05-09 00:00:00
Date Available	2018-05-09 00:00:00
Creation Date	2018-04-24 11:51:40
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-04-24 11:52:14
Document Title	Exhibit D Users Manual per 2 1033 b3
Document Creator	Adobe InDesign CC 13.1 (Windows)

This device complies with Part 15 of FCC Rules. Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Trimble® Ranger 7 Handheld
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void user’s authority to operate the equipment.
Connecting ORION® Module(s) to
the Trimble Ranger 7
This equipment has been tested and found to comply within the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a different circuit from that to which the receiver
is connected
•
Consult the dealer or an experienced radio/TV technician for help
Module outer view
A minimum separation distance of 20 cm must be maintained between the antenna and the person for
this device to satisfy the RF exposure requirements.
NNOTE:
Making Water Visible®
ORION antenna
For complete information about the Trimble Ranger 7
handheld, see the user manual shipped with the handheld.
AF
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module. Under such configuration,
FCC Part 2.1091 radiation exposure limits set forth for population/uncontrolled environment can
be satisfied.
Module inner view
Trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and
enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding
contractual obligation exists. © 2018 Badger Meter, Inc. All rights reserved.
ORI-QS-02771-EN-01 (April 2018)
www.badgermeter.com
This device complies with Part 15 of FCC Rules. Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Quick Start Guide
Trimble® Ranger 7 Handheld
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire
de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void user’s authority to operate the equipment.
Connecting ORION® Module(s) to
the Trimble Ranger 7
This equipment has been tested and found to comply within the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a different circuit from that to which the receiver
is connected
•
Consult the dealer or an experienced radio/TV technician for help
Module outer view
Module inner view
ORION antenna
A minimum separation distance of 20 cm must be maintained between the antenna and the person for
this device to satisfy the RF exposure requirements.
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module. Under such configuration,
FCC Part 2.1091 radiation exposure limits set forth for population/uncontrolled environment can
be satisfied.
NNOTE:
For complete information about the Trimble Ranger 7
handheld, see the user manual shipped with the handheld.
Making Water Visible®
Trademarks appearing in this document are the property of their respective entities. Due to continuous research, product improvements and
enhancements, Badger Meter reserves the right to change product or system specifications without notice, except to the extent an outstanding
contractual obligation exists. © 2018 Badger Meter, Inc. All rights reserved.
www.badgermeter.com
ORI-QS-02771-EN-01 (April 2018)
Quick Start Guide
IIMPORTAN
Make sure the Ranger 7 is powered off before connecting or
removing a module.
1. On the back of the Ranger 7, use a Phillips #1 screwdriver to
loosen the two (2) screws on the module bay cover to remove it.
NNOTE:
Store the module bay cover somewhere safe for potential
future use.
2. Hook the ORION module onto the Ranger 7, making sure that
the slots on the top of the device line up with those on
the module.
The module bay can accommodate one or both ORION
modules (ME and CE), side-by-side.
4. Repeat steps 2 and 3 to install the second ORION module,
if necessary.
AF
NNOTE:
3. Tighten the two (2) captive screws at the bottom of the module
using a Phillips #1 screwdriver. Do not overtighten the screws.
5. Attach antenna to each module by threading it on the
antenna connector at the top of the module until it is tight.
Do not overtighten.
IIMPORTAN
Make sure the Ranger 7 is powered off before connecting or
removing a module.
1. On the back of the Ranger 7, use a Phillips #1 screwdriver to
loosen the two (2) screws on the module bay cover to remove it.
NNOTE:
Store the module bay cover somewhere safe for potential
future use.
2. Hook the ORION module onto the Ranger 7, making sure that
the slots on the top of the device line up with those on
the module.
NNOTE:
The module bay can accommodate one or both ORION
modules (ME and CE), side-by-side.
3. Tighten the two (2) captive screws at the bottom of the module
using a Phillips #1 screwdriver. Do not overtighten the screws.
4. Repeat steps 2 and 3 to install the second ORION module,
if necessary.
5. Attach antenna to each module by threading it on the
antenna connector at the top of the module until it is tight.
Do not overtighten.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Has XFA                         : No
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Create Date                     : 2018:04:24 11:51:40-05:00
Metadata Date                   : 2018:04:24 11:52:14-05:00
Modify Date                     : 2018:04:24 11:52:14-05:00
Creator Tool                    : Adobe InDesign CC 13.1 (Windows)
Instance ID                     : uuid:aff1a0b6-bd38-4278-a933-3e33615596e5
Original Document ID            : xmp.did:EDC2D6D55E5FDF1192F0B2EF2D23A40D
Document ID                     : xmp.id:fcc09270-1d4d-bb4e-a3a4-2d12ee03742c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:38022072-4e30-514c-8955-5a71b7618b50
Derived From Document ID        : xmp.did:93848ab8-9843-f04b-be02-627ca0fb09ec
Derived From Original Document ID: xmp.did:EDC2D6D55E5FDF1192F0B2EF2D23A40D
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Windows)
History Changed                 : /
History When                    : 2018:04:24 11:51:40-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 13.1 (Windows)

EXIF Metadata provided by EXIF.tools