Baicells Technologies EG7010C LTE Outdoor CPE User Manual ATOM OD06 EG7010C USER Manual

Baicells Technologies Co., Ltd. LTE Outdoor CPE ATOM OD06 EG7010C USER Manual

User Manual

01 All rights reserved © Baicells Technologies Co., Ltd. ATOM OD06 - EG7010C USER Manual
2 1. Shipping List Make sure you have got the following parts: EG7010C Quick Guide PoE Adapter Power Cord Standard Mounting Kits Optional Mounting Kits
2. Hardware Introduction 2.1 Indicators Identity Description Color Status Description MIU - Yellow OFF Reserved. Steady On Reserved. Blanking Reserved. LTE Network state Indicator Blue OFF LTE disconnected. Steady On LTE connected. SIM SIM card status indicator Yellow Steady On The SIM card is normal. Blanking The SIM card is abnormal or not inserted. LAN 100Mbps Eth Indication Yellow OFF Ethernet connection does not established. Steady On Ethernet connection is normal. Blanking Data is transmitting. PWR Power Indicator Yellow OFF No Power Supply Steady On Power On LTE Signal 5 LTEs, Indicate Green All OFF Signal is too weak to attach. Steady On According to signal strength in turn light
Identity Description Color Status Description connection state and signal strength up Blanking Scanning the LTE network The CPE is authenticating. CPE is getting IP address from the LTE network. 2.2 Interface and Buttons Interface & Button Description PoE Connected to the PoE Power Adapter TF Support SD card SIM Support 1.8V/3.0V USIM 2FF RESET Long press over 10 seconds to restore the factory settings GND Connected to Earth by conductor
3. Installation Guide 3.1 Support Materials Before installation, prepare the following support materials accordingly, as given below: Item Description Ethernet cable Outdoor Shield CAT5E Shorter than 330 feet Ground wire 16mm² yellow-green wire 3.2 Install USIM Card and Cables (1) Screw the screw on the waterproof cover, and open the waterproof cover (2) Insert the USIM card to the USIM slot. Note following the directions (3) Connect the Ethernet cable to the PoE port (4) connect the ground cable to the ground screw (5) Close the waterproof cover and fasten the screw on the cover. (6) Connected Ethernet cable to the power adapter. Pay attention to the power adapter interface directions. (7) Power on, the LED indicator will light up.
4. Configuration Guide 4.1 4.1 Login The CPE manages, configures, and maintains the device by web management page. The steps to log in are as follows: 1. In the address column of browser, type in http://192.168.150.1, then press “Enter”: 2. Enter the user name and password, click "LOGIN". After password authentication, you can log on to the web management page. The default user name and password is admin. For security, it is recommended that you open the firewall, and keep your login password, WLAN FTP passwords and password well. 4.2 View Status In the overview area, you can view the device information and LTE status,such as Product name, Software version, PLMN, IMSI, RSRP, RSRQ, CINR, SINR, Tx Power, Cell ID, PCI, and so on, as shown below:
5. Specifications Basic Specifications Item Description UE-Category 3GPP R10, CAT 6/7 USIM Slot 1.8V/3.0V USIM 2FF Ethernet Port 1 RJ45, LAN, 10/100/1000 auto-sensing, auto-MDX, PoE Power Supply Input: Universal range 100V~240V AC Output: PoE (24V DC, 0.5A) Reset Button Tactile button. Long press over 10s to restore the factory settings LED Indicators MIU/LTE/SIM/LAN/PWR/LTE Signal Dimensions 241mm (H) x 154mm (W) x 50mm (D) Weight About 900 g LTE Specifications Item Description LTE Mode LTE-TDD LTE Bands Band 43 TXRX 2T4R
Channel Bandwidth 5MHz, 10MHz, 15MHz, 20MHz Modulation QPSK, 16QAM Receive Sensitivity -94dBm @ QPSK,20MHz, 25°C MAX Output Power 19±2dBm Antenna Type Internal directional-antenna Antenna Gain 10dBi@3.xGHz, 2 Ports Polarization ±45° Antenna Efficiency >70% Isolation ≤-25dB VSWR ≤2 Horizontal Beam Width (3dB) 60±3°@3.xGHz, 2 Ports Vertical Beam Width (3dB) 25±5°@3.xGHz, 2 Ports WiFi Specifications (Just for Alignment) Item Description Standard IEEE 802.11b/g/n Channel Bandwidth 20MHz Frequency 2.4GHz TXRX 1T1R Peak Rate 802.11b: 11Mbps 802.11g: 54Mbps 802.11n: 300Mbps Modulation DSSS/CCK, OFDM
Receive Sensitivity -64 dBm@65Mbit/s, typical for 802.11n -65 dBm@54Mbit/s, typical for 802.11g -76 dBm@11Mbit/s, typical for 802.11b MAX Output Power 15±2dBm Antenna Type Internal omni-antenna Antenna Gain 0dBi SW Specifications Item Description Language Support English/Chinese Network Mode NAT/Bridge/Tunnel IP Protocol IPv4/IPv6 SIM Management PIN Management, SIM Lock Network Connection Management Auto/Manual LTE Scan Mode Full band scan, Frequency Lock WLAN  WPS  MSSID Isolation  VLAN VPN  L2TP  GRE NAT  Port forwarding  DMZ  ALG  Port Trigger Firewall  IP/MAC/URL Filter  Access Control  Block Port Scanner / SYN Flood  SPI Filter
Network Management  TR069  SNMP Diagnostics  TCPDump  Ping  Trace route Statistics  LTE Status/Connection Time/System Up Time  Device Status  DHCP Client List  WiFi Station List  LTE Status  Firewall Status Maintenance  Date & Time setting  Reboot  Restore factory settings  Restore / Back up configuration file  Firmware upgrade locally/OTA (over the air) System Log  Operating Log  Run-time Log  Filter/Select/Display/Export Log Environmental Specifications Item Description Operating Temperature -40°C to 55°C Storage Temperature -40°C to 70°C Operating Humidity 5% to 95% Ingress Protection Rating IP65
1 6. Regulatory Compliance FCC Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Warning: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
2 ISEDC Compliance This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d' Innovation, Science et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, End-Users must be provided with transmitter operation conditions for satisfying RF exposure compliance.

Navigation menu