Baja DB30 User Manual DOODLE BUG MINI BIKE Manuals And Guides L0912190

BAJA Gokarts/Minibikes Manual L0912190 BAJA Gokarts/Minibikes Owner's Manual, BAJA Gokarts/Minibikes installation guides

User Manual: Baja DB30 DB30 BAJA DOODLE BUG MINI BIKE - Manuals and Guides View the owners manual for your BAJA DOODLE BUG MINI BIKE #DB30. Home:Toys & Games Parts:Baja Parts:Baja DOODLE BUG MINI BIKE Manual

Open the PDF directly: View PDF PDF.
Page Count: 8

1. Remove carton top.
1. Remove set up instructions,
owners manual and parts.
2. Locate white moisture absorbing
packet and discard. Note: This packet
is for shipping purposes only.
Rev. A
Front fork assembly Hardware
10mm Front
Fork Lock Nut __
2 large Washers
2 Beveled
Washers lOmm X 165mm Front Fork Bolt Yellow Front Reflector
Front Fender and Hardware
O0
8mm
lock Nuts 8mm X 25mm
Bolts
Front Fender
2 Rubber Grommets
Red Rear Reflector
Castle nut cover
Front Tire and Hardware
Cotter Pin
12mm Front Axle bolt
12mm Washer
Castle Nut Wheel Spacers
Front Wheel
Cable Ties
1. Install fork assembly. Make sure throttle cable,
brake cable, and on/off switch wire are routed
correctly through front fork assembly. (See
photo for correct wire and cable placement)
Fork
Assembl
Brake Cable
2. Attach fork assembly by inserting fork
bolt down through 1-large washer, 2-Top
fork bracket, 3- Beveled washer facing down
4- Down tube, 5- Beveled washer facing up,
6- Bottom fork bracket, 7-large washer, 8-
lock nut provided.
Torque to 20 ft/Ibs
ON/OFF Switch wire cable
Beveled
Washer
Beveled portion o'f
washer faces down
Beveled
Washer
Beveled portion of
washer faces up
Large washer
Top Fork bracket
Down Tube
10mm Lock Nut Bottom Fork bracket
Large washer
.Use 3 plastic cable ties provided to secure
brake cable and engine ON/OFF switch wire
to mini bike frame (See photo for correct
placement of cable ties) Make sure there
are no kinks and that brake cable and wiring
have free movement when handle bars are
turned left and right. Apply brakes making
sure brakes work properly with free
movement.
ON/OFF
switch wire
Brake cable
Plastic cable ties
Plastic cable ties
.Run throttle cable along top of mini bike
frame. Use 2 plastic cable ties provided to
secure throttle cable to frame (See photo
for correct placement of cable ties). Make
sure throttle works smoothly and snaps back
into place after cable ties are in place. Move
handle bars left and right making sure cable
has free movement and does not pull against
throttle lever or throttle portion of engine..
Plastic cable ties Throttle cable
8mmX25mmbolt
RubberGrommets
1. Installfrontfender.Makesurelarge
portionoffenderisoverwheel.Install
withrubbergrommetbetweenframe
andfender.Tightenwith8mmNutsand
8mmX25mmboltsprovided.
Torquebolts to 15ft/Ibs
8mmLocknuts
FenderOrientation.
Largerparttoward
frontoverwheel.
1. Startingwith leftside(leftsideisdefinedas
leftsideof minibikewhilesittinginriding
position),slideaxlethrough 1-fork,2-small
wheelspacer,3-wheel.4-largewheelspacer,
5-fork,6-washer.Note:Placelargespaceron
rightsideof wheelandsmallerspaceronleft
sideofwheel. CotterPin
cover Left
Axle
Smallwheelspacerleftside.
2. Placecastlenutonendof axleandtighter
snug.Oncetight, insertcotterpinandbend
overendswithapairof pliers.
3.Placerubbercastlenutcoverovernutand
cotterpin
Largewheelspacerrightside
CotterPin
Castlenutcover
Bendcotterpinend
Riding minibike without cotter pin installed on front and rear wheel axles could be
hazardous
Riding minibike without cotter pins installed increases the risk of front and/or rear
wheels coming loose which could result in severe injury or death.
Before riding, make sure front and rear axle cotter pins are installed.
Red Rear Reflector
1. There are three red reflectors. These reflectors
need to be attached to the rear of the minibike,
one on each side and one on the rear. Screw each
reflector onto the welded bracket clockwise (CW).
Yellow Front Reflector
2. There are two yellow reflectors. These reflectors
need to be attached to the front of the minibike,
one on each side. Screw each reflector onto the
welded bracket clockwise (CW).
1. Drainpackingoil andfill withcorrect
amountandtypeof oilasspecifiedin
owners manual
Oil Fill Plug
2. Fill gas tank as specified in
owners manual.
3. Refer to owners manual for starting I
I
instructions
Oil Drain plug
WARNING!
This Mini Bike may be shipped with packing oil
in engine. This oil should be drained and re-
placed with new engine oil as described in the
owners manual. Never attempt to start engine
without first replacing engine oil with proper
amount and grade as described in owners
manual.
If you have any questions
Please call Toll Free
1-888-863-2252

Navigation menu