User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3406424 |
| Application ID | D1bRlFKRxhoKtcEWDbjfPQ== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 57.39kB (717391 bits) |
| Date Submitted | 2017-05-28 00:00:00 |
| Date Available | 2017-05-28 00:00:00 |
| Creation Date | 2017-04-11 17:23:46 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2017-05-22 12:26:39 |
| Document Title | Microsoft Word - (BIS M-403-057-002-02-SA1) UserMan |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | A316164 |
BALLUFF
BIS M‐403‐057‐002‐02‐SA1
Component Specification
BALLUFF RFID CUSTOM AERIAL 13.4 MM +
AMPLIFIER
X0000131
Vendor Name:
BALLUFF
Vendor P/N:
Vendor Name:
Vendor P/N:
Vendor Name:
Vendor P/N:
Vendor Name:
Vendor P/N:
Vendor Name:
Vendor P/N:
Vendor Name:
Vendor P/N:
TO BE DEFINED
Guidelines for Efficient and Safe Use
General
Read this information before using your modelname module. For any exceptions, due to national
requirements or limitations, when using your WLAN module, please contact Manufacturer.
Changes or modifications to the product not expressly approved by Manufacturer will void the user's
authority to operate the equipment.
Regulatory Statements
FCC Statement
FCC end product labeling instruction
In accordance with 47 CFR § 15.19 the end product shall bear the following statement in a conspicuous
location on the device: "This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. this device may not cause harmful interference, and 2. this device must accept any interference received,
including interference that may cause undesired operation."
When the device is so small or for such use that it is not practicable to place the statement above on it, the
information shall be placed in a prominent location in the instruction manual or pamphlet supplied to the
user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC ID
label must be displayed on the device.
In case, where the final product will be installed in locations where the end‐consumer is not able to see the
FCC ID and/or this statement, the FCC ID and the statement shall also be included in the end‐product
manual.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's
authority to operate the equipment.
End Product Labeling
The final end product must be labeled in a visible area with the following:
"Contains FCC ID: 2AGZY-BF‐IDM05”
Information for the OEMs and Integrators
The following statement must be included with all versions of this document supplied to an
OEM or integrator, but should not be distributed to the end user.
1) This device is intended for OEM integrators only.
2) Please see the full Grant of Equipment document for other restrictions.
Balluff Device Specifications
Balluff device (Processor + Antenna) model
BIS‐M‐403‐057‐002‐02‐SA1
The processor can read/write up to 98bytes
Balluff device Firmware version
Firmware version: V 1.0.
Patch applied on the board to report the FW version
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : A316164 Create Date : 2017:04:11 17:23:46+08:00 Modify Date : 2017:05:22 12:26:39+08:00 XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Producer : Acrobat Distiller 9.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2017:05:22 12:26:39+08:00 Format : application/pdf Title : Microsoft Word - (BIS M-403-057-002-02-SA1) UserMan Creator : A316164 Document ID : uuid:8de338b7-f14c-433b-93d9-ecc822609d67 Instance ID : uuid:b0d84e21-6a4d-4805-9a0e-2b14ad305108 Page Count : 7EXIF Metadata provided by EXIF.tools