Balluff BFIDU03 RFID Reader User Manual Statement and Warning

Balluff GmbH RFID Reader User Manual Statement and Warning

Contents

User-Manual-Statement and Warning

Balluff GmbH, Schurwaldstraße 9, 73765 Neuhausen a.d.F., Germany,
Telefon +49 7158 173-0, Fax +49 7158 5010, balluff@balluff.de, www.balluff.com
BF-IDU03
RFID-Reader
BIS VU-32X-C1-…
FCC ID: 2AGZY-BFIDU03
IC: 20739-BFIDU03
Dieses Produkt wurde unter Beachtung der in den Ländern USA und Kanada geltenden Richtlinien entwickelt und
gefertigt. Die Konformität wurde nachgewiesen.
The product was developed and manufactured in accordance with the directives
applicable in the USA and Canada. Conformity has been verified.
Este producto se ha desarrollado y fabricado observando las directivas vigentes
en EE. UU. y Canadá. La conformidad ha sido demostrada.
Betriebsspannung VS
Operating voltage
Tensión de servicio
19.2…28.8 V DC
Stromaufnahme bei 24 V DC
Current draw (at 24 V DC)
Consumo de corriente a 24 V CC
≤ 200 mA
Betriebsfrequenz
Operating frequency
Frecuencia de servicio
902…928 MHz
maximale zulässige abgestrahlte Leistung
Maximum permissible radiated power
Potencia radiada máxima permitida
< 1000 mW EIRP
Anzahl genutzter Kanäle
Number of used channels
Número de canales utilizados
52
Kanalwahlverfahren
Channel selection process
Procedimiento de selección de canal
Automatisch (Frequenzsprungverfahren)
Automatic (frequency hopping method)
Automático (procedimiento de salto de frecuencia)
Modulation
Modulation
Modulación
PR-ASK
Unterstützte Profile
Supported profiles
Perfiles
TX 40 kHz RX 40 kHz FM0
TX 40 kHz RX 40 kHz Miller-4
TX 40 kHz RX 160 kHz FM0
TX 40 kHz RX 160 kHz Miller-4
TX 80 kHz RX 160 kHz FM0
TX 80 kHz RX 160 kHz Miller-4
TX 40 kHz RX 256 kHz Miller-4
TX 80 kHz RX 256 kHz Miller-4
TX 80 kHz RX 320 kHz Miller-2
TX 80 kHz RX 320 kHz Miller-4
TX 80 kHz RX 320 kHz Miller-8
TX 160 kHz RX 640 kHz Miller-4
Balluff GmbH, Schurwaldstraße 9, 73765 Neuhausen a.d.F., Germany,
Telefon +49 7158 173-0, Fax +49 7158 5010, balluff@balluff.de, www.balluff.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance voids the user's authority to
operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiofrequency radiation exposure Information:
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un Environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Ce transmetteur ne doit pas être place au même endroit ou utilise simultanément avec un autre transmetteur ou
antenne.

Navigation menu