User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 958222 |
| Application ID | qrlmwCHVaaB2Gp3Gbqgzpg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 13.11kB (163869 bits) |
| Date Submitted | 2008-06-20 00:00:00 |
| Date Available | 2008-06-20 00:00:00 |
| Creation Date | 2008-04-03 16:47:40 |
| Producing Software | OpenOffice.org 2.3 |
| Document Lastmod | 2008-06-19 14:22:48 |
| Document Title | User Manual |
| Document Creator | Writer |
| Document Author: | cemil |
Operation Manual 0039A02C-253/IDE-SD-MIF-AGFA REVISION 1.0, 2008-04-02 The IDE_SD_MIF_AGFA is a RFID Read-/Write-Device (short: reader) which is compatible to all Mifare cards. The reader also supports ISO14443A/B and ISO15693 and all cards compliant to these standards. It provides a serial interface RS232 to output or exchange data with a host computer and a 13,56MHz inductive interface to supply power to and exchange data with the Mifare/ISO compliant card (or other available form-factors such as tags, key-fobs). Mounting and Connection The reader generates a magnetic field with the frequency of 13.56MHz which is influenced by any electrically conductive material in close proximity to the device. When mounting the unit, a distance to any such material of minimum 10 cm is required to ensure that there will be no significant degradation of the performance in terms of read range and reliability. Mounting the unit directly to metal would result in a severe reduction of read range down to zero functionality. Care should be taken when testing the device after mounting at a problematic environment: Read ranges and performance vary from card to card and very much from card to tag or key-fob. When mounting multiple readers, the distance between readers should be minimum 0.5 m in order to avoid degradation of performance due to interference. To connect the device to a Host computer, please make sure the host system provides an 6-pin plug connector intended for connection of the reader Operation Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the serial interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader. Technical Data DC Electrical Characteristics Symbol Vdd Idd Idd1 Vih Vil Ii Parameter Supply Voltage Supply current Peak Supply current Input high voltage Input low voltage Input leakage current Condition Min Typ Max 4.75 5 5.5 400 Inrush 450 3.3 Vdd+0.3 -0.3 0.8 300 Units VDC mA mA uA Additional requirements for the supply voltage: Vripple = 50mVpp max. RF Characteristics ● ● ● Operating frequency: 13.56 MHz Data transmission modulation reader to card: ASK Data transmission modulation card to reader: ASK/load modulation Pinout 6-Pin plug connector and Signal Descriptions Pin Name TX1 RX1 GND PWR Type Output Input Power Power Description RS232-data from reader RS232-data to reader Ground 5V Power Supply Not connected Not connected Serial Interface The TXD/RXD signals are compatible with RS-232 level signals. The interface operates at 2400 baud, no parity, 8 data bits, 1 stop bit. Upon detection of a valid card swipe, the reader outputs the card number in ASCII format. Temperature ● ● ● Operating temperature range: 0…45°C Storage temperature range: -20…+60°C Thermal shock: 30°C/min maximum dT/dt Humidity ● ● Operating: 20% to 80% relative humidity; non condensing Non-operating: 10% to 90% relative humidity; non condensing General regulatory requirements FCC: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The final product should contain labelling according to FCC requirements. For example: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains FCC ID OKY1003925351A02C. This label will be placed on the final product, clearly visible to all persons exposed to the equipment��
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 About : uuid:28806339-3ac7-4167-8ea6-792abe12550d Producer : OpenOffice.org 2.3 Create Date : 2008:04:03 16:47:40+02:00 Creator Tool : Writer Modify Date : 2008:06:19 14:22:48+02:00 Metadata Date : 2008:06:19 14:22:48+02:00 Document ID : uuid:3c601cd7-c988-4fd3-93f8-08aacb8275ae Instance ID : uuid:a770b5ed-ccef-4097-9d84-fe32974fbe93 Format : application/pdf Creator : cemil Page Count : 3 Author : cemilEXIF Metadata provided by EXIF.tools