User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1150428 |
| Application ID | x7lKXwwmjGXbNmD/JHsC8g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 10.32kB (128969 bits) |
| Date Submitted | 2009-08-07 00:00:00 |
| Date Available | 2009-08-07 00:00:00 |
| Creation Date | 2009-06-17 11:52:06 |
| Producing Software | OpenOffice.org 2.1 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | User Manual |
| Document Creator | Writer |
| Document Author: | cemil |
Operation Manual IDE-Small-ID-Tablet/with boards 0039PBA02,0572A02 and 0573A01 REVISION 1.0, 2009-06-17 The Small-Id Tablet (it consists of parts PCB 0039PBA02,PCB 0572A02 and mounting board 0573A01) is a RFID Read-/Write-Device (short: reader) which is compatible to all Mifare cards. The reader also supports ISO14443A/B and ISO15693 and all cards compliant to these standards. All functions of reader can be controlled over USB- Interface or RS232-interface which allows data exchange with a host computer. This includes: switch on/off RF-Field read/write to a transponder Mounting and Connection The reader generates a magnetic field with the frequency of 13.56MHz which is influenced by any electrically conductive material in close proximity to the device. When mounting the unit, a distance to any such material of minimum 10 cm is required to ensure that there will be no significant degradation of the performance in terms of read range and reliability. Mounting the unit directly to metal would result in a severe reduction of read range down to zero functionality. Care should be taken when testing the device after mounting at a problematic environment: Read ranges and performance vary from card to card and very much from card to tag or key-fob. When mounting multiple readers, the distance between readers should be minimum 0.5 m in order to avoid degradation of performance due to interference. Operation Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the serial interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader. Technical Data DC Electrical Characteristics Symbol Vdd Idd Idd1 Vih Vil Ii Parameter Supply Voltage Supply current Peak Supply current Input high voltage Input low voltage Input leakage current Condition Min Typ Max 4.75 5 5.5 150 250 Inrush 450 3.3 Vdd+0.3 -0.3 0.8 300 Units VDC mA mA uA Additional requirements for the supply voltage: Vripple = 50mVpp max. RF Characteristics Operating frequency: 13.56 MHz Data transmission modulation reader to card: ASK Data transmission modulation card to reader: ASK/load modulation Pinout 4-Pin USB plug and Signal Descriptions Pin Name Type Description V_BUS Power USB-Power Supply D- I/O USB Data inverted D+ I/O USB Data GND Power Ground Temperature Operating temperature range: 0…45°C Storage temperature range: -20…+60°C Thermal shock: 30°C/min maximum dT/dt Humidity Operating: 20% to 80% relative humidity; non condensing Non-operating: 10% to 90% relative humidity; non condensing General regulatory requirements FCC: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Canada: This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 3 Author : cemil Creator : Writer Producer : OpenOffice.org 2.1 Create Date : 2009:06:17 11:52:06+02:00EXIF Metadata provided by EXIF.tools