Baltech 10117810A01A RFID Card Reader User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3419492
Application ID	FabNmVqtepGhljEojuJF7A==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	76.7kB (958735 bits)
Date Submitted	2017-06-09 00:00:00
Date Available	2017-07-10 00:00:00
Creation Date	2017-05-31 11:55:01
Producing Software	Microsoft® Word 2016
Document Lastmod	2017-05-31 11:55:01
Document Title	Manual
Document Creator	Microsoft® Word 2016
Document Author:	cemil

Operation Manual
RFID Reader “IDE-ZG-L-MFB-USB”
Covered Variants:
M/N: 10117-810
M/N: 10117-x1y1z1
REVISION 1.0, 2017-05-31
BALTECH AG
Lilienthalstraße 27
85399 Hallbergmoos
Germany
Phone: +49 (811) 99 88 1- 0
FAX: +49 (811) 99 88 1- 11
e-mail: info@baltech.de
http://www.baltech.de/
“x“, “y” and “z” shall represent any alphanumerical number or can be left blank.
Introduction
The “IDE-ZG-L-MFB-USB” Reader/Writer is a desktop contactless smart card USB and
Bluetooth© wireless technology smart card reader and writer combining the high- and low
frequency card technologies. It supports ISO 14443A/B, ISO 15693, Legic Advant and Legic Prime
standards as well as all major 125kHz-based transponders.
Based on BALTECH’s core technology it provides support of the latest smartcard technologies,
encryption and security features.
Mounting and Connection
The reader generates a magnetic field at 13.56MHz and/or at 125 KHz frequencies which could be
influenced by any electrically conductive material close to the device.
To ensure good performances and functionalities in terms of read range and reliability a minimum
distance of 10cm from such materials is required. Mounting the unit directly to metal would result
in a severe reduction of read range down to zero functionality. Care should be taken when testing
the device after mounting at a problematic environment: Read ranges and performance vary from
card to card and very much from card to tag or key-fob.
When mounting multiple readers, the distance between readers should be minimum 0.5 m in
order to avoid degradation of performance due to interference.
To connect the device to a host system (a printer or a PC), please make sure that the system
provides an USB socket intended for connection of the reader.
Operation
Whenever the device is connected to a proper power supply, it will switch on the internal antenna
and periodically scan for a card. Once a card has been detected, the card number is read, the data
converted and sent to the host system through the USB Interface. To enable the device to read
cards, tags and key-fobs successfully, they should be placed centred above the reader.
-1-
Technical Features
Operating Frequency
•
0.125MHz
•
13.56MHz
•
2402MHz-2480MHz
Data transmission ASK
modulation reader to card:
Data transmission AM/Load modulation
modulation card to reader:
Interfaces
USB: Full speed 2.0, RS 232, Bluetooth© Smart 4.2
Supported standards: ISO14443 A & B, ISO15693
Contactless Card
Communication speed ISO14443A/B: Baud rate up to
424kBaud
Operating Range
•
LA ISO14443A/B: up to 5cm
•
ISO15693: up to 8cm
•
125kHz: up to 6cm
•
Bluetooth© wireless technology: up to 5m
Human
Supply Power [VDC]
Power Consumption [W]
Operating Temperature [°C]
LED & Buzzer
USB bus powered: 5 (±5%)
Up to 1.5 / 1 typ.
-20 to +65
Operating Humidity [%]
20 to 80 relative humidity; non-condensing
Non-Operating Humidity [%]
10 to 90 relative humidity; non-condensing
Dimension
Weight
57mmx35mmx9mm
11g
Pinout 4-Pin USB-A plug and Signal Descriptions
Pin
Name
PWR
DD+
GND
Type
Power
Output
Input
Power
Description
5V Power Supply
USB-Data inverted
USB-Data
Signal and Power Ground
-2-
General regulatory requirements for 10117-810
FCC ID OKY10117810A01A
IC: 7657A-10117810
NOTICE:
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Changes or modifications made to this equipment not expressly approved by BALTECH AG may void
the FCC authorization to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
-3-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 4
Language                        : de-DE
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator                         : cemil
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2017:05:31 11:55:01+02:00
Modify Date                     : 2017:05:31 11:55:01+02:00
Document ID                     : uuid:CBA92BB8-DB83-4F9E-B134-395F2CFDA179
Instance ID                     : uuid:CBA92BB8-DB83-4F9E-B134-395F2CFDA179
Author                          : cemil

EXIF Metadata provided by EXIF.tools