Baltech 1056200101A02C Tag Reader User Manual ACCESS45 5 232 LEGP LB Operation Manual
Baltech AG Tag Reader ACCESS45 5 232 LEGP LB Operation Manual
Baltech >
User Manual
Operation Manual 10562-02-001 /Y591-EIND-101 REVISION 1.0, 2009-01-07 The Y591-EIND-101 is a RFID Read-/Write-Device (short: reader). The reader supports Hitag© family tags and Indala cards. It provides a serial interface RS232 to output or exchange data with a host computer (typically an Equitrac Page Counter Unit, a printer or a copy machine) and a 125kHz inductive interface to supply power to and exchange data with the tags. The host computer can control a bi-colour LED and a beeper to interface with the user. Mounting and Connection The reader generates a magnetic field with the frequency of 125kHz which is influenced by any electrically conductive material in close proximity to the device. When mounting the unit, a distance to any such material of minimum 10 cm is required to ensure that there will be no significant degradation of the performance in terms of read range and reliability. Mounting the unit directly to metal would result in a severe reduction of read range down to zero functionality. Care should be taken when testing the device after mounting at a problematic environment: Read ranges and performance vary from card to card and very much from card to tag or key-fob. When mounting multiple readers, the distance between readers should be minimum 0.5 m in order to avoid degradation of performance due to interference. To connect the device to an Equitrac PageCounter, printer or copy machine, please make sure the host system provides an 14-pin Mini-DIN socket intended for connection of the reader. Operation Whenever the device is connected to a proper power supply, it will switch on the internal antenna and periodically scan for a card. Once a card has been detected, the card number is read, the data converted and sent to the host system through the serial interface. To enable the device to read cards, tags and key-fobs successfully, they should be placed centred above the reader. Technical Data DC Electrical Characteristics Symbol Vdd Idd Idd1 Parameter Supply Voltage Supply current Peak Supply current Condition Inrush Min Typ Max 4.75 5 5.25 250 450 Units VDC mA mA Additional requirements for the supply voltage: Vripple = 50mVpp max. RF Characteristics Operating frequency: 125kHz Data transmission modulation reader to card: AM Data transmission modulation card to reader: ASK and PSK Pinout RS422-Interface MDR 14-Pole connector plug and Signal Descriptions Pin 10 11 12 13 14 Name GND -TX RS422 +TX RS422 -RX RS422 +RX RS422 +5V Power +5V Return Type Power Output Output Input Input Power Power I/O Description Signal and Power Ground RS422-data from reader RS422-data from reader Not connected RS422-data to reader RS422-data to reader Not connected Signal and Power Ground Not connected Power Ground Not connected Connected Not connected Not connected Temperature Operating temperature range: 0…45°C Storage temperature range: -20…+60°C Thermal shock: 30°C/min maximum dT/dt Humidity Operating: 20% to 80% relative humidity; non condensing Non-operating: 10% to 90% relative humidity; non condensing FCC: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Canada: This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 3 Title : ACCESS45-5-232-LEGP-LB Operation Manual Author : juergen roesch Creator : Writer Producer : OpenOffice.org 2.1 Create Date : 2009:01:07 09:41:25+01:00EXIF Metadata provided by EXIF.tools