Barco N V R9861510 ClickShare CS-100 User Manual
Barco NV ClickShare CS-100
User manual
CS-100
User guide
R5900024/00
21/12/2014
Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
Phone: +32 56.23.32.11
Fax: +32 56.26.22.62
Support: www.barco.com/en/support
Visit us at the web: www.barco.com
Printed in China
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in
the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures
which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the
customer.
Barco ClickShare End-User License Agreement (EULA/Software License)
PLEASE READ THIS DOCUMENT CAREFULLY BEFORE OPENING OR DOWNLOADING AND USING SOFTWARE OR HARDWARE
PROVIDED TO YOU BY BARCO AS IT CONTAINS THE TERMS AND CONDITIONS BY WHICH BARCO OFFERS TO LICENSE THE
SOFTWARE. BY OPENING THE SOFTWARE PACKAGE, OR USING THE HARDWARE IN WHICH THE SOFTWARE IS EMBEDDED,
YOU AGREE TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT.
The Software as supplied by BARCO is licensed, not sold to you, on a non-exclusive basis for use only under the terms of this license,
and BARCO reserve all rights not expressly granted to you. You may own the carrier on which the Software is provided, but the Software
is owned and copyrighted by BARCO or by third party suppliers. Your license confers no title or ownership and is not a sale of any rights
in the Software or its documentation.
By installing, executing and/or using the Software, either as initial version or as an upgrade, update, patch or enhancement of a prior
release, this Software License shall supersede any terms and conditions previously agreed upon (whether or not in writing) between Barco
and you with respect to the subject matter of this Software License and such previous terms shall from the date hereof cease to have any
force or effect; provided, however that this Software License shall not be construed as a renunciation, discharge or waiver of any right or
remedy provided in any terms and conditions previously agreed upon with respect to a failure of either party to perform any of its obligations
under any terms and conditions previously agreed upon.
Software Specifications
The Software contains the following software products: ClickShare
Software License Terms
1. This Software License is between you and BARCO NV, a corporation organized and existing under the laws of Belgium registered
under number BE 0473.191.041, Commercial Companies’ Register of Kortrijk, having its registered office President Kennedypark, 35
at B-8500 Kortrijk, Belgium ("Barco") for the use of the Software.
You hereby undertake to inform all users authorized by you to make use of the computing device on which the Software is loaded/in-
stalled (“Authorized Users”) of the terms of this Software License and to bind all Authorized Users to accept all such terms of this
Software License as applies to them.
2. Barco grants you a limited, non-exclusive, non-assignable, non-transferable user license (without the right to grant sublicenses).
Unless specifically agreed upon otherwise between you and Barco or unless specifically allowed by the Software (or its DRM man-
agement) itself, i) the license under this Software License applies to one (1) copy of the Software to be used on one single computing
device and ii) installation on a computing device that may be concurrently accessed by more than one user shall not constitute a
permitted use and a separate license is required for each active user connected to a computing device on which the Software is being
used.
You and Authorized Users are entitled to use the Software for the purposes and in the manner set out in this Software License (and
documentation), but neither you nor any Authorized User are entitled to: (i) sell or grant a security interest in the Software to other
parties in any way, or to rent, lease or sub-license the Software to others without the express prior written consent of Barco; or (ii)
exploit the Software or any of its component parts for any commercial purpose, other than use by you and/or Authorized Users of the
Software.
Neither you nor any Authorized User may, whether in whole or in part, copy, translate, reverse engineer, derive source code from,
modify, disassemble, decompile, create derivative works based on the Software, or remove any proprietary notices or labels on the
Software, save as may be permitted by law or this Software License, without the prior consent, in writing, of Barco.
3. Barco (and Barco’s licensors, as appropriate) retain ownership of all intellectual property rights in the Software and any copies you
or any Authorized User may make of such Software. The Software is protected by national copyright laws, international copyright
treaties and conventions, and other applicable laws. All rights not expressly licensed to you in this Software License are reserved
to Barco and Barco’s licensors, as appropriate. The Software contains certain other licensed materials and Barco’s licensors may
protect their rights in the event of any violation of this Software License.
4. Barco shall hold you harmless, defend and indemnify you from and against direct damages, losses and expenses arising from in-
fringement or alleged infringement of any patent, trademark or copyright of such third party by the license and the right to install the
Software as permitted by this Software License and settle at its sole expense any amounts awarded in a final judgment or settlement
resulting therefrom, under the condition that (i) you promptly notify Barco in writing after a claim has been asserted against you or
the commencement of any claim, action, suit or proceeding (whichever is the earlier), and (ii) Barco shall be allowed to assume sole
control of the defense and any settlement negotiations related to any claim, action, suit or proceeding, and (iii) you shall not negotiate,
settle or compromise any claim, action, suit or proceeding without the prior written consent of Barco and (iv) you, at your cost, shall
cooperate with Barco and provide assistance and support, as may reasonably be required by Barco, in connection with the defense
and any settlement negotiations related to any claim, action, suit or proceeding. Barco shall have no indemnity obligation for any
Software, or any portion thereof, (i) that is based on specifications, drawings, models or other data furnished by you or, (ii) that is
not provided by Barco or, (iii) that is modified, in spite of the prohibition for you to modify the software or, (iv) to the extent that you
continue allegedly infringing activity after having been provided modifications that avoid the alleged infringement, or (v) where the use
of the Software, or the combination or thereof with other Software, processes or materials or the distribution thereof rather than the
Software itself is the primary cause of an alleged infringement. In case it has been determined by a finally awarded judgment that
Barco infringed or misappropriated such third party rights or earlier, at Barco’s discretion, it may, at its option and cost, (i) modify the
Software in such a way that it shall not infringe upon or misappropriate the rights of the third party or (ii) obtain for you a license or
other right to use the rights allegedly infringed or (iii) replace the Software in question with non-infringing Software. The remedies set
forth in this paragraph shall constitute your sole and exclusive remedy and Barco’s sole and exclusive liability for a third party claim
that the Software infringes or misappropriates any intellectual property right of a third party.
5. The duration of this Software License will be from the date of your acceptance (as set forth above) of the Software (whereby you ac-
knowledge that use of the Software implies acceptance), with no termination date, unless otherwise specified. You may terminate this
Software License at any time by destroying all copies of the Software then in your possession and returning all associated materials
and documentation, to Barco or the appointed Barco reseller that sold or provided these to you. Barco may terminate this Software
License forthwith by informing you at any time if you and/or any Authorized User are in breach of any of the Software License’s terms.
6. YOU UNDERSTAND THAT THE SOFTWARE IS BEING PROVIDED TO YOU "AS IS". BARCO DOES NOT MAKE NOR INTENDS
TO MAKE ANY WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY FITNESS, FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF INTELLEC-
TUAL PROPERTY AND DOES NOT WARRANT THAT THE SOFTWARE WILL BE FREE FROM ERRORS OR THAT SUCH ERRORS
WILL BE CORRECTED BY BARCO AND YOU ARE SOLELY RESPONSIBLE FOR ALL COSTS AND EXPENSES ASSOCIATED
WITH RECTIFICATION, REPAIR OR DAMAGE CAUSED BY SUCH ERRORS.
YOU ALSO ACKNOWLEDGE AND AGREE THAT:
BARCO ACCEPTS NO LIABILITY FOR ANY DAMAGES, LOSSES OR CLAIMS YOU OR ANY THIRD PARTY MAY SUFFER AS
A RESULT OF YOUR USE OF THE SOFTWARE. IN JURISIDCTIONS WHERE BARCO’S LIABILITY CANNOT BE EXCLUDED,
BARCO’S LIABILITY FOR DIRECT DAMAGES SHALL BE LIMITED TO AN AMOUNT OF 250 EURO IN THE AGREGATE (OR TO
THE MAXIMUM EXTENT PERMITTED BY LAW WHERE NO FURTHER EXCLUSION IS LEGALLY ALLOWED).
TO THE MAXIMUM EXTENT PERMITTED BY LAW, IN NO EVENT WILL BARCO BE LIABLE FOR ANY INDIRECT, SPECIAL,
PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES OF ANY KIND WHICH MAY ARISE OUT OF OR IN CON-
NECTION WITH THE SOFTWARE, THIS SOFTWARE LICENSE OR THE PERFORMANCE OR PURPORTED PERFORMANCE
OF OR FAILURE IN THE PERFORMANCE OF BARCO’S OBLIGATIONS UNDER THIS SOFTWARE LICENSE OR FOR ANY ECO-
NOMIC LOSS, LOSS OF BUSINESS, CONTRACTS, DATA, GOODWILL, PROFITS, TURNOVER, REVENUE, REPUTATION OR
ANY LOSS ARISING FROM WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION OF THE SOFTWARE AND ANY AND
ALL OTHER COMMERCIAL DAMAGES OR LOSSES WHICH MAY ARISE IN RESPECT OF USE OF THE SOFTWARE, EVEN IF
BARCO HAS BEEN ADVISED OF THE POSSIBILITY OF THEIR OCCURRENCE.
YOU HEREBY AGREE TO INDEMNIFY, KEEP INDEMNIFIED, DEFEND AND HOLD HARMLESS BARCO AND BARCO’S AFFILI-
ATES AND SUBSIDIARIES FROM AND AGAINST ANY AND ALL ACTIONS, PROCEEDINGS, LIABILITY, LOSS, DAMAGES, FEES
AND COSTS (INCLUDING ATTORNEYS" FEES), AND OTHER EXPENSES INCURRED OR SUFFERED BY BARCO ARISING OUT
OF OR IN CONNECTION WITH ANY BREACH BY YOU OF THE TERMS OF THIS SOFTWARE LICENSE.
7. You shall treat as confidential all information obtained from the other pursuant to this Software License which is marked "confidential"
or the equivalent or has the necessary quality of confidence about it and shall not divulge such information to any persons without
Barco’s prior written consent provided that this Paragraph 7 shall not extend to information which was rightfully in the possession of
you prior to the commencement of the negotiations leading to this Software License, which is already public knowledge or becomes
so at a future date (otherwise than as a result of a breach of this paragraph 7), is required to be disclosed by law or which is trivial or
obvious. You are aware of and ensure to comply with the provisions of this paragraph 7. The foregoing obligations as to confidentiality
shall survive any termination of this Software License.
8. You will remain responsible for the maintenance of your hardware, operating system, the functioning of your network and in keeping
your systems virus-free. You acknowledge that the Software is a complex computer software application, and that the performance
thereof may vary depending hardware platform, software interactions and configuration. You acknowledge that the Software is not
designed and produced specifically to meet your specific requirements and expectations and the selection of the Software by you is
entirely your own choice and decision. For the avoidance of doubt, nothing in this Software License shall impose any obligation on
Barco to provide support services (on the Software or any other hardware or software product).
9. This Software License is the only understanding and agreement between you and Barco for use of the Software by you and/or Autho-
rized Users. The Software License supersedes all other communications, understandings or agreements we had prior to this Software
License (with the exception of any continuing confidentiality agreement) although nothing in this Software License purports to exclude
liability for fraudulent misrepresentation. You may not export or re-export the Software or any copy or adaptation in violation of any
applicable laws or regulations. This Software License shall not be altered, amended or varied. If any provision of this Software Li-
cense is determined to be illegal, void or unenforceable, or if any court of competent jurisdiction in any final decision so determines,
this Software License shall continue in full force save that such provision shall be deemed to be deleted with effect from the date of
such decision, or such earlier date, and shall be replaced by a provision which is acceptable by law and which embodies the intention
of this Software License a close as possible.
10. You acknowledge that this Software may be subject to U.S. or other governments Export Jurisdiction. You agree to comply with all
applicable international and national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as
end-user, end-use, and destination restrictions issued by the U.S. or other governments.
11. Barco shall be entitled to sub-contract all or any of Barco’s obligations hereunder to a third party and/or any of Barco’s affiliated
companies.
12. The construction, validity and performance of this Software License shall be governed in all respects by the laws of Belgium without
recourse to its conflict of law principles. All disputes arising in any way out of or affecting this Software License shall be subject
to the exclusive jurisdiction of the courts of Kortrijk, without prejudice to enforcement of any judgment or order thereof in any other
jurisdiction. The United Nations Convention on Contracts for the International Sale of Goods (the "Convention") shall not apply to this
Software License, however, if the Convention is deemed by a court of competent jurisdiction to apply to this Software License, Barco
shall not be liable for any claimed non-conformance of the Software under Article 35(2) of the Convention.
Trademarks Software License Terms
Brand and product names mentioned in relation to the Software may be trademarks, registered trademarks or copyrights of their respective
(third party) holders. All such brand and product names mentioned in relation to the Software serve as comments or examples and are not
to be understood as advertising for the products or their manufacturers.
Privacy Policy
You acknowledge and agree that the Software is gathering technical information about the functionality of the products which are connected
through the Software (“Functional Information”) and that Barco may make use of such Functional Information (with the exclusion of any
personal data) for any reason Barco sees fit, including but not limited to providing services to you / your organization, allowing third party
to access to such Functional Information and/or to provide services to you / your organization .
You hereby explicitly give consent that Barco may gather, access, preserve, and/or disclose the personal data you provide to us (e.g.
connected with your account allowing for the gathering of Functional Information as well as any content associated with that account) as
well as personal information we receive from you through the use of the Software:
• For the benefit of the business purposes of Barco and/or its affiliates;
• In order to provide, maintain, protect and/or improve the Software and to develop new software;
• For administration of the relationship between you, your organization and Barco and/or its affiliates ;
• For any other legitimate purpose (including i) direct marketing purposes from Barco, its affiliates or selected third parties, and ii)
allowing third parties to provide services to you related to the Software);
• if required to do so by law or in a good faith belief that such access preservation or disclosure is reasonably necessary to:
- Satisfy any applicable law, regulation, legal process or enforceable governmental request;
- Enforce this Software License, including investigation of potential violations hereof;
- Detect, prevent, or otherwise address fraud, security or technical issues (including, without limitation, the filtering of spam);
- Protect against imminent harm to the rights, property or safety of Barco, its users or the public as required or permitted by law.
Barco shall not process any “sensitive information” whatsoever, including but not limited to medical information.
You understand that the technical processing and transmission of or by the Software, including your content, may involve:
• Transmissions over various networks;
• Changes to conform and adapt to technical requirements of connecting networks, devices and/or services.
You hereby explicitly give consent that Barco may export your personal data to any country worldwide, especially to any country where
Barco and/or its affiliates have infrastructure, or where a third party is making available infrastructure to Barco and/or its affiliates, to process
personal data.
Barco fully adheres to the EU Directive 95/46/EC on the protection of individuals with regard to the processing of personal data and the
free movement of such data, as implemented in the local EU member states. In accordance with these regulations, you have a right of
access to, and rectification of, your personal data. You may exercise these rights by contacting Barco.
Open Source Software provisions:
This product contains software components released under an Open Source license. A copy of the source code is available on request
by contacting your Barco customer support representative.
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTATION ARE PROVIDED "AS IS" WITH-
OUT EXPRESS OR IMPLIED WARRANTY INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTOR
BE LIABLE FOR DIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POS-
SIBILITY OF SUCH DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIA-
BILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS OPEN SOURCE
SOFTWARE. MORE INFORMATION/DETAILS IS TO BE FOUND IN EACH SPECIFIC OPEN SOURCE LICENSE.
Copyright on each Open Source Software component belongs to the respective initial copyright holder, each additional contributor and/or
their respective assignee(s), as may be identified in the respective documentation, source code, README file, or otherwise. You shall not
remove or obscure or otherwise alter the respective copyrights.
You acknowledge living up to the conditions of each separate Open Source Software license.
In the development of the Software, the following Open Source Software components have been used (an updated list may be made
available through the (customer section of the) Barco website or other (online) means):
Open Source component Open Source License
acl http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
acpid http://www.gnu.org/licenses/gpl.html
attr http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
http://www.gnu.org/licenses/gpl.html
alsa-lib
http://www.gnu.org/licenses/lgpl.html
http://www.gnu.org/licenses/gpl.html
alsa-utils
http://www.gnu.org/licenses/lgpl.html
Open Source component Open Source License
http://www.gnu.org/licenses/gpl.html
alsa-plugins
http://www.gnu.org/licenses/lgpl.html
avahi http://www.gnu.org/licenses/lgpl.html
Bootstrap (3.1.1) https://github.com/twbs/bootstrap/blob/master/LICENSE
bootstrap-dialog https://github.com/twbs/bootstrap/blob/master/LICENSE
bootstrap-slider.js v2.0.0 http://www.apache.org/licenses/LICENSE-2.0
busybox http://opensource.org/licenses/GPL-2.0
Chart.js https://github.com/nnnick/Chart.js/blob/master/LICENSE.md
Datepicker for Bootstrao (1,6,0-dev) http://www.apache.org/licenses/LICENSE-2.0
dropbear http://opensource.org/licenses/mit-license.php
fakeroot http://www.gnu.org/licenses/gpl.html
coreutils http://www.gnu.org/licenses/gpl.html
crda http://opensource.org/licenses/ISC
cron http://opensource.org/licenses/ISC
Crypto++ http://www.cryptopp.com/License.txt
dbus http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
dhcpd http://opensource.org/licenses/ISC
dm-crypt http://creativecommons.org/licenses/by-sa/3.0/
dmidecode http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
e2fsprogs http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
eglibc http://www.gnu.org/licenses/lgpl.html
ethtool http://www.gnu.org/licenses/gpl.html
express http://opensource.org/licenses/MIT
FFmpeg http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
http://freetype.sourceforge.net/FTL.TXT
freetype
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
gdbserver http://www.gnu.org/licenses/gpl.html
gmp http://www.gnu.org/licenses/lgpl.html
grub http://www.gnu.org/licenses/gpl.html
gstreamer http://www.gnu.org/licenses/lgpl.html
hdparm http://opensource.org/licenses/BSD-3-Clause
hostapd http://opensource.org/licenses/BSD-3-Clause
HTML5 Shiv 3.7.2 http://github.com/aFarkas/html5shiv/blob/master/MIT%20and%20GPL2%20licenses.md
i18next (1.10.0) https://opensource.org/licenses/MIT
i2c-tools http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
iftop http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
imx-bootlets http://www.gnu.org/licenses/gpl.html
iperf http://opensource.org/licenses/BSD-3-Clause
iproute2 http://www.gnu.org/licenses/gpl.html
iptables http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
Open Source component Open Source License
iw http://opensource.org/licenses/BSD-3-Clause
Jasny Bootstrap (3.1.3) http://www.apache.org/licenses/LICENSE-2.0
jQuery Form Plugin (3.51.0-2014.06.20) https://github.com/malsup/form#copyright-and-license
jQuery JavaScript Library (1.11.3) https://jquery.org/license/
https://github.com/ablanco/jquery.pwstrength.bootstrap/blob/master/GPL-LICENSE.txt
jQuery Password Strength plugin for
Twitter Bootstrap https://github.com/ablanco/jquery.pwstrength.bootstrap/com-
mit/19480555e8c7c2f417d78a78dac63056fa221f6a
jQuery Upload File Plugin (4.0.8) https://github.com/hayageek/jquery-upload-file
jQuery Validation Plugin (1.13.1) https://opensource.org/licenses/MIT
kobs-ng http://www.gnu.org/licenses/gpl.html
libarchive http://opensource.org/licenses/bsd-license.php
libav http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libavutil http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libcap2 http://www.gnu.org/licenses/gpl.html
libdaemon0 http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libdrm2 http://opensource.org/licenses/MIT
libexpat1 http://opensource.org/licenses/MIT
libfontconfig1 http://opensource.org/licenses/BSD-3-Clause
libfontenc1 http://opensource.org/licenses/BSD-3-Clause
libgcc1 http://www.gnu.org/licenses/gpl.html
http://www.gnu.org/licenses/gpl.html
http://www.gnu.org/licenses/lgpl.html
libgcrypt11
http://www.gnu.org/copyleft/fdl.html
libglib-2 http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libgnutls26 http://www.gnu.org/licenses/lgpl.html
http://www.gnu.org/licenses/gpl.html
http://www.gnu.org/licenses/lgpl.html
libgpg-error0
http://www.gnu.org/copyleft/fdl.html
libjpeg-turbo http://opensource.org/licenses/BSD-3-Clause
libjpeg8 BSD like licensee
libnl2 http://www.gnu.org/licenses/lgpl.html
libNotify https://wiki.gnome.org/FoundationBoard/Resources/LicensingAgreement
libnss-mdns http://www.gnu.org/licenses/gpl.html
libpam http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
libpcap http://opensource.org/licenses/BSD-3-Clause
libpcre0 http://opensource.org/licenses/BSD-3-Clause
libpixman-1-0 http://changelogs.ubuntu.com/changelogs/pool/main/p/pixman/pixman_0.10.0-
0ubuntu1/libpixman-1-0.copyright
libpng12-0 http://www.libpng.org/pub/png/src/libpng-LICENSE.txt
libpopt0 http://opensource.org/licenses/MIT
libresample http://www.gnu.org/licenses/lgpl.html
Open Source component Open Source License
libsm6 http://metadata.ftp-master.debian.org/changelogs//main/libs/libsm/libsm_1.2.2-1_copyright
libstdc++6 http://www.gnu.org/licenses/gpl.html
libswscale http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libtalloc2 http://www.gnu.org/licenses/lgpl.html
libusb http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
libva Copyright (c) 2011, Advanced Micro Devices, Inc. All rights reserved.
libX11 http://opensource.org/licenses/MIT
libXdamage http://opensource.org/licenses/MIT
libXext http://opensource.org/licenses/MIT
libXfixes http://opensource.org/licenses/MIT
libXinerama http://opensource.org/licenses/MIT
libxml2 http://opensource.org/licenses/MIT
libXrender http://opensource.org/licenses/MIT
libXtst http://opensource.org/licenses/MIT
libz1 Free license
lighttpd http://opensource.org/licenses/BSD-3-Clause
linux http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
lmsensors http://www.gnu.org/licenses/gpl.html
logrotate http://www.gnu.org/licenses/gpl.html
makedevs http://www.gnu.org/licenses/gpl.html
memtest86plus http://www.gnu.org/licenses/gpl.html
mesa http://opensource.org/licenses/MIT
modernizr (3.1.0) https://opensource.org/licenses/MIT
module-init-tools http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
modutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
monit http://www.gnu.org/licenses/gpl.html
ncurses http://opensource.org/licenses/MIT
netbase http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
node.js https://raw.github.com/joyent/node/v0.10.26/LICENSE
openssl http://www.openssl.org/source/license.html
openssh-sftp-server http://opensource.org/licenses/BSD-3-Clause
opkg http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
passport http://opensource.org/licenses/MIT
passport-http http://opensource.org/licenses/MIT
pciutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
http://perldoc.perl.org/perlartistic.html
perl
http://www.gnu.org/licenses/old-licenses/gpl-1.0.html
php http://www.php.net/license/3_01.txt
procps http://www.gnu.org/licenses/gpl.html
pulseaudio http://www.gnu.org/licenses/lgpl.html
Open Source component Open Source License
qt http://doc.qt.io/qt-5/lgpl.html
read-edid Free license
Respond.js https://github.com/scottjehl/Respond/blob/master/LICENSE-MIT
rockbox-imxtools http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
rsync (<3.0.0) http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
rsync (>=3.0.0) http://www.gnu.org/licenses/gpl.html
rsyslog http://www.gnu.org/licenses/gpl.html
splashutils http://www.gnu.org/licenses/gpl.html
sprintf-js https://opensource.org/licenses/BSD-3-Clause
sscep https://github.com/certnanny/sscep/blob/master/COPYRIGHT
strace http://opensource.org/licenses/BSD-3-Clause
sysfsutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
sysvinit http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
tcpdump http://opensource.org/licenses/BSD-3-Clause
Timepicker Component for Twitter
Bootstrap https://opensource.org/licenses/MIT
ttf-arphic-uming http://ftp.gnu.org/non-gnu/chinese-fonts-truetype/LICENSE
ttf-dejavu-common http://dejavu-fonts.org/wiki/License
ttf-dejavu-sans http://dejavu-fonts.org/wiki/License
ttf-dejavu-sans-mono http://dejavu-fonts.org/wiki/License
https://osdn.jp/cvs/view/efont/sazanami/README
ttf-sazanami-gothic
http://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-
sazanami_20040629-8_copyright (translation)
https://osdn.jp/cvs/view/efont/sazanami/README
ttf-sazanami-mincho
http://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-
sazanami_20040629-8_copyright (translation)
ttf-un-fonts http://www.gnu.org/licenses/gpl.txt
u-boot http://www.denx.de/wiki/U-Boot/Licensing
uClibc http://www.gnu.org/licenses/lgpl.html
udev http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
update-modules http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
update-rc http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
usbutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
util-linux-ng http://www.gnu.org/licenses/gpl.html
wireless_tools http://www.gnu.org/licenses/gpl.html
wpa_supplicant http://opensource.org/licenses/BSD-3-Clause
xserver-xorg http://opensource.org/licenses/MIT
xvba-video http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
zeroconf http://www.gnu.org/licenses/gpl.html
EN55022-CISPR22 Class B ITE (Information Technology Equipment)
This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to
take adequate measures.
If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the
following measures :
• Re-orientation of the receiving antenna for the radio or television.
• Relocate the equipment with respect to the receiver.
• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
• Fasten cables connectors to the equipment by mounting screws.
Federal Communication Commission Interference Statement
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You ma y also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." This
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate
this equipment under Federal Communications Commissions rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio & television reception.
FCC RF Radiation Exposure Statement: This device is capable of operating in 802.11a mode. For 802.11a devices operating in the
frequency range of 5.15 - 5.25 GHz, they are restricted for indoor operations to reduce any potential harmful interference for Mobile Satellite
Services (MSS) in the US. WIFI Access Points that are capable of allowing your device to operate in 802.11a mode (5 .15 - 5.25 GHz band)
are optimized for indoor use only. If your WIFI network is capable of operating in this mode, please restrict your WIFI use indoors to not
violate federal regulations to protect Mobile Satellite Services.
Base Unit FCC ID: 2AAED-R9861510
Button FCC ID (model R9861006D01): XF6-RS9110N1103
Button FCC ID (model R9861500D01): 2AAED-R9861500D01
ClickShare Button R9861500D01 has been tested and meets the FCC RF exposure guidelines.The maximum SAR value reported is
0.915W/kg.
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Barco
Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.
Base Unit IC ID: IC: 9393B-R9861510
Button IC ID (model R9861006D01): 8407A-RS9110N1103
Button IC ID (model R9861500D01): 9393B-R9861500D01
IC Antenna statement
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter 9393B-R9861510 has been approved by Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Type: Dipole
Maximum Peak Gain: 2 dBi
Impedance: 50 Ohm
Canada, avis d’lndustry Canada (IC)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Informations concernant l’exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil Barco est inférieure à la limite d’exposition aux fréquences radio d’Industry Canada
(IC). Utilisez l’appareil de sans fil Barco de façon à minimiser les contacts humains lors du fonctionnement normal.
IC ID Unité de Base: 9393B-R9861510
IC ID Button (modèle R9861006D01): 8407A-RS9110N1103
IC ID Button (modèle R9861500D01): 9393B-R9861500D01
Déclaration d’antenne d’Industrie Canada (IC)
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain
maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
Le présent émetteur radio 9393B-R9861510 a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés
ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Type: Dipole
Gain maximum: 2 dBi
Impédance: 50 Ohm
Table of contents
TABLE OF CONTENTS
1. Introduction ........................................................................................................ 3
1.1 Versions of the product .............................................................................................................. 3
1.2 About this guide ..................................................................................................................... 3
1.3 Symbols and fonts . . ................................................................................................................. 4
2. Introduction to CS-100 ........................................................................................... 5
2.1 About the CS-100 ................................................................................................................... 5
2.2 About the Base Unit ................................................................................................................. 6
2.3 About the Button..................................................................................................................... 7
2.4 Mobile Device Support .............................................................................................................. 8
3. Getting started..................................................................................................... 9
3.1 Activating the base unit.............................................................................................................. 9
3.2 Basic Use............................................................................................................................ 9
3.3 User Interface........................................................................................................................11
3.4 Capture more........................................................................................................................12
3.5 Shared desktop: primary - extended................................................................................................13
3.6 Audio configuration..................................................................................................................15
3.7 Pairing ...............................................................................................................................17
4. Troubleshooting .. ...... ...... ...... ...... ...... ...... .. .... .. ...... ...... ...... ...... .. .... .. .... .. ...... ...... ...19
4.1 Basic Troubleshooting ...............................................................................................................19
5. Environmental information ......................................................................................21
5.1 Disposal information.................................................................................................................21
5.2 Rohs compliance ....................................................................................................................21
5.3 Production address ..................................................................................................................22
5.4 Importers contact information .......................................................................................................22
R5900024 CS-100 21/12/2014 1
Table of contents
2R5900024 CS-100 21/12/2014
1. Introduction
1. INTRODUCTION
Overview
• Versions of the product
• About this guide
• Symbols and fonts
1.1 Versions of the product
Regional versions
Depending on the location where you buy the CS-100 product, the Base Unit and accessories are regionalized. By the time of
release of this manual, 3 regional versions of CS-100 are available:
• Europe & Japan
• North America
• China
The regional version of your CS-100 cannot be changed. That means that you cannot use it in another region.
For more information on the regional variants, refer to the CS-100 Installation Guide.
1.2 About this guide
This manual
Partnumber Description Level
R5900024 User Guide User
Available System documentation
This guide is part of the documentation set describing the CS-100 product.
Guide Article number
User Guide R5900024
Installation Guide R5900022
Safety Guide R5900031
Service Guide R5900026
Button Guide R5900007
Recycling Manual R5900028
API Guide R5900018
A printed copy of the Safety Guide and an electronic version on USB stick of the user and installation guide is included in the CS-100
box at purchase.
Always check for the latest version of the manual on www.barco.com/clickshare Click on Visit the ClickShare
product page and go to tab Downloads..
Depending on the CS-100 version, some graphics might be different to the ones used in this manual. This
however does not have any effect to the functionality.
R5900024 CS-100 21/12/2014 3
1. Introduction
The User Guide describes how to use your CS-100. It also contains a basic troubleshooting part where you can search for a solution
when a problem occurs.
1.3 Symbols and fonts
Symbol overview
The following icons are used in the manual :
Caution
Warning
Info, term definition. General info about the term
Note: gives extra information about the described subject
Tip: gives extra advice about the described subject
Font overview
• Buttons are indicated in bold, e.g. OK.
• Menu items are indicated in italic.
• Step related notes, tips, warnings or cautions are printed in italic.
• Procedure related notes, tips, warnings or cautions are printed in bold between 2 lines preceded by the corresponding icon.
4R5900024 CS-100 21/12/2014
2. Introduction to CS-100
2. INTRODUCTION TO CS-100
Overview
• About the CS-100
• About the Base Unit
• About the Button
• Mobile Device Support
2.1 About the CS-100
CS-100 sets
CS-100 makes connecting to the meeting room’s video system a matter of clicking a Button. This CS-100 only helps the presenter
get the presentation on-screen in a second, but it also allows the other people in the meeting to participate more actively. The result
is enhanced meeting efficiency and better decision-making.
At the moment 3 different sets are available on the market. Each set is sold in its specific region and it can only be used in that
specific region.
Components CS-100 set
A standard CS-100 set consists of a Base Unit and 1 Button. Depending on the location where you buy the product, the software of
the Base Unit is different. If needed, you can buy additional Buttons.
1
2
Image 2-1
1 Base unit
2Button
Accessories included
Depending on the country where you buy the product, the following regionalized accessories are also included in the CS-100 box.
Regional version Contains Accessories included
R9861510xx1
• R9861510
• 1x R9861500D01
• DC adapter with AC clips type A, C,
G, I
• USB stick with user documentation
• Printed safety manual
Contact your local sales representative for the correct regional variant to be used in your country.
1. xx=EU, CN, NA,
R5900024 CS-100 21/12/2014 5
2. Introduction to CS-100
2.2 About the Base Unit
Base Unit functionality
The Base Unit receives the wireless input from the Buttons and controls the content of the meeting room display and the sound of
the meeting room’s audio system.
The Base Unit can be inside a cabinet in the meeting room, or put on the meeting room table or mounted on a wall. Check the
Installation Guide for instructions on how to install the Base Unit.
2
1
3
Image 2-2
1USB port
2Status LED ring
3 Power Button
Tabl e 2 -3
USB Port
The USB port is used to update the software of both the Base Unit and the Buttons.
When plugging in the Button into the Base Unit, the Button is paired to the Base Unit. The Base Unit checks whether the software
and firmware of the Button is up to date. If not, the Base Unit updates the software and/or firmware.
Status LED ring
The color of the LED ring around the power button of the Base Unit gives information on the status of the system.
LEDs behavior Explanation
static red
• receiving content from the Buttons and streaming towards the display.
• pairing and software update of the Button is done. You can now unplug the
Button from the Base Unit.
• during the first phase of the Base Unit boot process.
blinking white
• system is starting up (during the second phase)
• Button pairing is in progress
• software update of the Base Unit
breathing white
• ECO standby mode
• networked standby mode
static white
• awake and ready (i.e. showing the welcome message on the display)
• pairing is done
red blinking
• an error occurred
dark
• deep standby/off
Power button
The button at the front of the Base Unit has a power on/off function once the Base unit is powered.
• When the system is powered on, a push makes the system to shut down and power off.
• When the system is shut down, a push triggers the system to start up.
6R5900024 CS-100 21/12/2014
2. Introduction to CS-100
2.3 About the Button
Button functionality
A Button contains three main functional components.
1 2 3
Image 2-3
The Button
1 USB connector
2Button
3LEDring
Tabl e 2 -5
Handle the Button cable with care. Rough handling might cause defects.
USB connector
Using the USB connector the Button can be plugged into a laptop (for sharing your screen) or in the Base Unit (for pairing the Button
to the Unit or updating its software).
Button
Click the Button to display the content of the laptop’s screen on the meeting room display. Clicking the Button during the meeting
will toggle the sharing of the screen.
LED ring
The LED ring indicates the current status of your CS-100.
LEDs behavior Explanation
white blinking
• the Button is plugged in the laptop and initializing or waiting for the user
to start the ClickShare application.
• pairing/software update of the Button in the Base Unit is in progress.
static white
• ClickShare is ready to start sharing your screen.
• pairing is done. You can now unplug the Button from the Base Unit.
static red
• sharing your screen with the display.
• pairing and software update is done. You can now unplug the Button
from the Base Unit.
red blinking
• an error occurred.
off (no light)
• the Button is not or not properly inserted into the USB port.
• the Button might be defective.
• the USB port or computer might be defective.
R5900024 CS-100 21/12/2014 7
2. Introduction to CS-100
2.4 Mobile Device Support
Overview
The below list of Apps are supported by ClickShare and can be installed on your mobile device from Google Play or Apple App Store.
Before you can use your mobile device with ClickShare, you have to connect the mobile device Wi-Fi with the ClickShare Base Unit
Wi-Fi. Follow the instructions as given in your mobile device user guide.
App Used on Logo
ClickShare App iOS
Android
MirrorOp Sender for Galaxy Galaxy mobile devices
8R5900024 CS-100 21/12/2014
3. Getting started
3. GETTING STARTED
Overview
• Activating the base unit
•BasicUse
• User Interface
• Capture more
• Shared desktop: primary - extended
•Audioconfiguration
• Pairing
3.1 Activating the base unit
About power mode
The Base Unit is powered via an external power adapter. Once connected, the Base Unit is automatically switched in standby mode.
For more information about power connection, see CS-100’s installation manual.
On and off
1. Push the button shortly.
Image 3-1
Standby button
When the Base Unit was on, it goes out
When the Base Unit was off, it starts up.
3.2 Basic Use
Basic functionality
When entering a meeting room equipped with ClickShare and if the display is not in screensaver mode, the ClickShare wallpaper is
shown on the display. The content of the wallpaper depends on the setup.
Starting to use ClickShare is now very simple.
To start using ClickShare
1. Take a Button and Insert the Button into a USB port of your laptop.
R5900024 CS-100 21/12/2014 9
3. Getting started
Image 3-2
The LEDs of the Button start flashing white.
On your laptop a new drive appears.
Two situations are possible now:
- A launcher is preinstalled on your laptop (downloaded from the Base Unit or Barco website, or deployed company-wide by
your IT department). ClickShare is immediately available. You can continue with step 4.
- nothing is pre-installed. Continue with step 2.
2. Browse to and double-click the ClickShare drive on your laptop.
Image 3-3
Windows environment
Image 3-4
MAC environment
3. Double-click the ClickShare application.
10 R5900024 CS-100 21/12/2014
3. Getting started
The ClickShare client software starts and its icon appears in the system tray.
On a Windows computer:
On a Macintosh:
When the system is ready for use, a message appears close to the systray icon.
Image 3-5
The LEDs of the Button are static white.
4. To share your screen on the display, click the Button.
The LEDs of the Button become static red and your screen appears on the display. When audio is enabled on the ClickShare
Base Unit, the audio of your laptop is also available on the audio output of the Base Unit and on the HDMI output, and it will be
played via the meeting room audio system. The icon returns to the same state as in step 3.
In the system tray, the ClickShare icon starts rotating. On Windows computers the icon changes into .
The name of the user logged on to the laptop which is sharing its content is briefly shown in the bottom left corner of the added
content.
ClickShare automatically scales the content of your screen to the resolution of the meeting room display. The aspect ratio of your
screen is maintained to make sure the proportions are correct.
5. To remove your content from the display, click the Button again.
The LEDs of the Button become static white.
6. When leaving the meeting room, unplug the Button from your laptop.
No trace of the ClickShare application is left on your laptop.
3.3 User Interface
User Interface functionality
After launching the client, the ClickShare icon appears in the system tray.
ClickShare context menu
The content of the context menu is related to the operating system.
1. Right-click the ClickShare icon in the system tray.
The context menu appears.
Image 3-6
Context menu
2. From the list, click the action you want to perform.
R5900024 CS-100 21/12/2014 11
3. Getting started
Click To Result
Start sharing to show your screen on the display. The LEDs of your Button become red.
Show me fullscreen to bring the content of your screen on
the display full screen.
The screens of other users that were
shown on the display disappear.
Settings... select the way to connect. Via
ClickShare Button or via a network
connection
Connected via Button or via network
Pair Button to pair the connected Button with the
Base Unit
Button is ready for use.
Capture mode to choose to capture video with more
(slower performance) or less detail
(faster performance).
Tune video performance and quality
Shared desktop (only for Windows7 and
Windows8)
to select primary or extended desktop Depending on the selection the primary
or the extended display is displayed.
About ClickShare Client to find out the ClickShare software
version.
Here you can find more information on
the ClickShare software version.
Exit to close ClickShare. The ClickShare icon disappears from
the system tray and the LEDs of the
Button start blinking white.
3.4 Capture more
Only for Windows XP, Windows Vista and Windows 7 & 8.
About capture more
ClickShare is optimized for optimum video performance. Upon starting the client software it will disable Win7 Aero Glass to maximize
video performance. Upon quitting the ClickShare applications your Aero Glass settings will be restored.
Transparent alpha layers are by default not captured. Therefore some windows may not be shown or may appear different on screen.
For example content of video players using overlays will not be shown.
With "Capture More" selected, Win7 Aero Glass settings will be restored and capturing of alpha layers is enabled. In this mode,
video throughput may decrease a bit and more details will be captured.
Default setting: Not checked.
How to change
1. Right click on the ClickShare icon in the system tray (1).
Image 3-7
Change capture mode
A context menu opens.
2. Click Capture More to toggle.
12 R5900024 CS-100 21/12/2014
3. Getting started
Checked: capture with more details but may have a lower performance.
Not checked: capture will be faster but may lose some of the details
Starting the client automatically in Capture More
The Capture more mode can be started by default so that the Aero Glass settings are not disabled. To do so, an environment variable
should be introduced in your windows. Ask you administrator or consult your windows documentation to find out how to create.
The following variable should be introduced :
Variable Value
CLICKSHARE_CAPTUREMOREBYDEFAULT 1
3.5 Shared desktop: primary - extended
Only for Window7 and Windows8
About shared desktop
Depending on your selection, your primary screen or your extended screen will be captured and displayed via ClickShare. That
extended screen can be a physical screen or a virtual screen.
With extended desktop you can take advantage of both your laptop screen and the central meeting room display. Presentation notes
or other material on primary screen will not be displayed to everyone.
PC with virtual extended screen:
1
2
Image 3-8
Primary screen displayed on the PC, extended screen displayed on the meeting room display.
1
22
Image 3-9
PC with one extended screen connected. That extended screen will be captured and displayed on the meeting room display.
R5900024 CS-100 21/12/2014 13
3. Getting started
3
1
22
Image 3-10
PC with two extended screens connected. The first extended screen, screen 2 will always be captured and displayed on the meeting
room display.
To know if your system supports the extended desk top feature, press Window key + P. It should bring up the
following pop-up on screen:
Image 3-11
How to select
1. Right click on the ClickShare icon in the system tray (1).
Image 3-12
Shared desktop selection
A context menu opens.
2. Select Shared Desktop (2).
3. Select the desired setting (3).
Primary : the primary PC screen is displayed on the meeting room display.
Extended always the secondary screen is displayed on the meeting room display.
14 R5900024 CS-100 21/12/2014
3. Getting started
Known issue
• Virtual Extended Desktop not supported on some Windows7 and Windows8 systems due to a problem in recent versions of
the AMD graphical driver. Downgrade to an older version of the driver might resolve the issue but make sure the AMD driver
updated above version 13.8 .
3.6 Audio configuration
Audio configuration
The connected user must control his own audio signal using the audio configuration of his computer. If he does not want to broadcast
his audio signal, he has to mute audio on his computer.
For some operating system, it is necessary to set ClickShare as your default output device. Once you unplug the Button, the default
setting is switched back to the previous setting.
Set ClickShare as default in Windows 7
1. Right click on the speaker icon in the system tray (1).
Image 3-13
Speakers ClickShare, default
2. Click Playback devices (2).
The Sound window opens on the Playback tab.
3. Select Speakers ClickShare (3) and click Set default (4).
4. Click Apply or OK to activate the new setting.
Set ClickShare as default in Windows XP
1. Right click on the speaker icon in the system tray.
R5900024 CS-100 21/12/2014 15
3. Getting started
Image 3-14
Speakers ClickShare, default
2. Click Adjust Audio Properties (1).
The Sound and Audio Devices Properties window opens.
3. Select Audio tab (2).
4. Click on the drop down box in the Sound playback pane and select ClickShare (3)..
5. Click Apply or OK to activate the new setting.
Set ClickShare as default on MAC
1. Click on the Apple logo on the menu bar (1) and select System Preferences.. ..(2).
16 R5900024 CS-100 21/12/2014
3. Getting started
Image 3-15
Speakers ClickShare, default
2. Click on the Speaker icon (3).
The Sound window opens.
3. Select the Output tab (4) and activate ClickShare (5).
3.7 Pairing
Pairing of the Buttons with the Base Unit
To be able to use a Button it should be assigned to the Base Unit you are using. This process is called pairing. By default, the two
Buttons delivered with the CS-100 set are already paired to the specific Base Unit.
In case you buy additional Buttons or when a Button should be assigned to another Base Unit, the Button needs to be paired (again).
The Button software update runs in the background and will not impact users while using the system. If desired, this feature can
be disabled in the Web Interface. When downgrading or updating to an older version of the Base Unit software the Buttons need to
paired manually to update their software.
A Button can only be paired to one Base Unit at a time.
The Button will always make connection to the Base Unit it was last paired to.
To pair a Button to the Base unit
1. Insert the Button in the USB port at the front of the Base Unit you are using.
R5900024 CS-100 21/12/2014 17
3. Getting started
Image 3-16
Pair button
Both the LEDs of the Button and the LEDs of the Base Unit are blinking white. This means pairing is in progress.
The Base Unit automatically checks whether the software of the Button is up to date. If not, the Base Unit updates the Button
software. This may take more time.
During the pairing and update process, a small status bar is display.
Image 3-17
Pairing message
The result of the pairing process can be as follows:
- When the LEDs become static white, the Button is paired to the Base Unit, but no software update was needed. You can
unplug the Button from the Base Unit.
- When the LEDs become static red, the Button is paired to the Base Unit and the software update has finished. You can unplug
the Button from the Base Unit.
Image 3-18
Pairing finished
2. Unplug the Button from the Base Unit.
The Button is now ready for use.
18 R5900024 CS-100 21/12/2014
4. Troubleshooting
4. TROUBLESHOOTING
4.1 Basic Troubleshooting
Problem solving
In this chapter some problems that might occur while using CS-100 are listed. For each problem possible causes are given and a
solution is proposed. If you cannot solve the problem yourself, please contact your local IT administrator.
Problem Cause Solution
You are the second person that wants to
share the content to the display.
The first user has to push his button to
remove his content so that a second user
can share his content. or
As second user, click and hold the Button
to use te Show me function of ClickShare.
Your screen is not shown on the display
when pressing the Button.
The ClickShare client software is not
running.
Go to the ClickShare drive and run the
software.
Your audio signal on your PC is muted Right click on the speaker icon and switch
off the mute.
Audio system of the meeting room is not
switched on
Switch on the audio system of the
meeting room.
When using separate audio, audio cable
is not connected
Check audio connection between the
Base Unit (audio out, green connector)
and the audio system of the meeting
room.
Default speaker is not correctly set . With a Button inserted, set ClickShare
speaker as your default speaker.
Your screen is shown, but your audio is
not playing on the meeting room audio
system
Buttons are not re-paired after changing
the audio setting on the web interface
Re-pair the buttons.
Your content is removed from the display
and the LEDs of your Button are blinking
white.
Connection to the display has been lost. ClickShare tries to restore the connection
automatically. If this fails, the LEDs of
the Button start blinking red. You should
unplug the Button from your laptop and
start a new.
The display is switched off. Switch on the display.
Wrong input is selected. Select the correct input.
The display cable is not connected
(correctly).
(Re)insert the display cable to the display
and the Base Unit.
The display does not recognize or is
not able to display the Base Unit output
resolution.
You or an administrator should change
the corresponding setting via the web
interface.
The Base Unit is in standby mode. Briefly push the standby button on the
Base Unit or plug in a Button and run the
ClickShare client software.
The Base Unit is powered off. Check if power adapter is connected to
the Base unit and to the wall outlet.
Nothing is shown on the display at all.
The Button’s software is not compatible
with that of the Base unit
Re-pair and update the software of the
Button by inserting it in the front USB port
of Base Unit.
R5900024 CS-100 21/12/2014 19
4. Troubleshooting
Problem Cause Solution
No automatic refresh of drives. Refresh the view on your laptop.
Bad connection at USB port on laptop.
• Reconnect to the USB port.
• Try another USB port.
• Reboot your laptop.
After inserting the Button into your laptop,
you cannot find the ClickShare drive.
Windows tries to assign the ClickShare
drive to an already reserved drive letter
Use Microsoft Windows Disk
Management to assign it to a free
drive letter.
Some programs of Windows are not
shown on the display.
Use of overlays, 3D or hardware
acceleration in the GPU. • Disable overlays or hardware
acceleration in the GPU.
• Disable AeroGlass in Windows 7
• Capture mode
20 R5900024 CS-100 21/12/2014
5. Environmental information
5. ENVIRONMENTAL INFORMATION
5.1 Disposal information
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately
from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will
appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects
on the environment and human health.
5.2 Rohs compliance
Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.
[Republic of Turkey: In conformity with the WEEE Regulation]
中国大陆RoHS – Chinese Mainland RoHS
根据中国大陆《电子信息产品污染控制管理办法》（也称为中国大陆RoHS）， 以下部分列出了Barco产品中可能包含的有毒和/或有
害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准：“电子信息产品中有毒物质的限量要求”中。
According to the “China Administration on Control of Pollution Caused by Electronic Information Products” (Also called RoHS of
Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may
contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the
section “Limit Requirements of toxic substances in Electronic Information Products”.
零件项目(名称)
Component Name
有毒有害物质或元素
Hazardous Substances or Elements
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印制电路配件
Printed Circuit
Assemblies
x0x000
电(线)缆
Cables
x0x000
R5900024 CS-100 21/12/2014 21
5. Environmental information
底架
Chassis
x0x000
电源供应器
Power Supply Unit
x0x000
文件说明书
Paper Manuals
000000
这个表被制备按照规定SJ/T 11364
This table is prepared in accordance with the provisions of SJ/T 11364.
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement in SJ/T11363.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part
is above the limit requirement in SJ/T11363.
在中国大陆销售的相应电子信息产品（EIP）都必须遵照中国大陆《电子信息产品污染控制标识要求》标准贴上环保使用期限（EFUP）
标签。Barco产品所采用的EFUP标签（请参阅实例，徽标内部的编号使用于制定产品）基于中国大陆的《电子信息产品环保使用期限
通则》标准。
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Electronic Information Products
Pollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The
number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard of Electronic Information Products
Environmental Friendly Use Period” of Chinese Mainland.
Image 5-1
5.3 Production address
Factory
Barco N.V.
12F, Citychamp Building, No. 12, Tai Yang Gong Zhong Lu, Chaoyang District, Beijing, P.R.C
Made in information
The made in country is indicated on the product ID label on the product itself.
Production date
The month and year of production is indicated on the product ID label on the product itself.
5.4 Importers contact information
Contact
To find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s web
site, www.barco.com.
22 R5900024 CS-100 21/12/2014