Barco N V R9861510 ClickShare CS-100 User Manual

Barco NV ClickShare CS-100

User manual

CS-100User guideR5900024/0021/12/2014
Barco NVPresident Kennedypark 35, 8500 Kortrijk, BelgiumPhone: +32 56.23.32.11Fax: +32 56.26.22.62Support: www.barco.com/en/supportVisit us at the web: www.barco.comPrinted in China
Copyright ©All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted orstored in a retrieval system without the prior written consent of Barco.TrademarksBrand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising forthe products or their manufacturers.Guarantee and CompensationBarco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchasermust immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barcomust be informed immediately in writing of any complaints.The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacementat its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand areduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct orindirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a componentof the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of propertiesguaranteed in writing or due to the intent or gross negligence or part of Barco.If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon inthe contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failureswhich are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normalmaintenance are not subject to the guarantee provided by Barco either.The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by thecustomer.Barco ClickShare End-User License Agreement (EULA/Software License)PLEASE READ THIS DOCUMENT CAREFULLY BEFORE OPENING OR DOWNLOADING AND USING SOFTWARE OR HARDWAREPROVIDED TO YOU BY BARCO AS IT CONTAINS THE TERMS AND CONDITIONS BY WHICH BARCO OFFERS TO LICENSE THESOFTWARE. BY OPENING THE SOFTWARE PACKAGE, OR USING THE HARDWARE IN WHICH THE SOFTWARE IS EMBEDDED,YOU AGREE TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT.The Software as supplied by BARCO is licensed, not sold to you, on a non-exclusive basis for use only under the terms of this license,and BARCO reserve all rights not expressly granted to you. You may own the carrier on which the Software is provided, but the Softwareis owned and copyrighted by BARCO or by third party suppliers. Your license confers no title or ownership and is not a sale of any rightsin the Software or its documentation.By installing, executing and/or using the Software, either as initial version or as an upgrade, update, patch or enhancement of a priorrelease, this Software License shall supersede any terms and conditions previously agreed upon (whether or not in writing) between Barcoand you with respect to the subject matter of this Software License and such previous terms shall from the date hereof cease to have anyforce or effect; provided, however that this Software License shall not be construed as a renunciation, discharge or waiver of any right orremedy provided in any terms and conditions previously agreed upon with respect to a failure of either party to perform any of its obligationsunder any terms and conditions previously agreed upon.Software SpecificationsThe Software contains the following software products: ClickShareSoftware License Terms
1. This Software License is between you and BARCO NV, a corporation organized and existing under the laws of Belgium registeredunder number BE 0473.191.041, Commercial Companies’ Register of Kortrijk, having its registered office President Kennedypark, 35at B-8500 Kortrijk, Belgium ("Barco") for the use of the Software.You hereby undertake to inform all users authorized by you to make use of the computing device on which the Software is loaded/in-stalled (“Authorized Users”) of the terms of this Software License and to bind all Authorized Users to accept all such terms of thisSoftware License as applies to them.2. Barco grants you a limited, non-exclusive, non-assignable, non-transferable user license (without the right to grant sublicenses).Unless specifically agreed upon otherwise between you and Barco or unless specifically allowed by the Software (or its DRM man-agement) itself, i) the license under this Software License applies to one (1) copy of the Software to be used on one single computingdevice and ii) installation on a computing device that may be concurrently accessed by more than one user shall not constitute apermitted use and a separate license is required for each active user connected to a computing device on which the Software is beingused.You and Authorized Users are entitled to use the Software for the purposes and in the manner set out in this Software License (anddocumentation), but neither you nor any Authorized User are entitled to: (i) sell or grant a security interest in the Software to otherparties in any way, or to rent, lease or sub-license the Software to others without the express prior written consent of Barco; or (ii)exploit the Software or any of its component parts for any commercial purpose, other than use by you and/or Authorized Users of theSoftware.Neither you nor any Authorized User may, whether in whole or in part, copy, translate, reverse engineer, derive source code from,modify, disassemble, decompile, create derivative works based on the Software, or remove any proprietary notices or labels on theSoftware, save as may be permitted by law or this Software License, without the prior consent, in writing, of Barco.3. Barco (and Barco’s licensors, as appropriate) retain ownership of all intellectual property rights in the Software and any copies youor any Authorized User may make of such Software. The Software is protected by national copyright laws, international copyrighttreaties and conventions, and other applicable laws. All rights not expressly licensed to you in this Software License are reservedto Barco and Barco’s licensors, as appropriate. The Software contains certain other licensed materials and Barco’s licensors mayprotect their rights in the event of any violation of this Software License.4. Barco shall hold you harmless, defend and indemnify you from and against direct damages, losses and expenses arising from in-fringement or alleged infringement of any patent, trademark or copyright of such third party by the license and the right to install theSoftware as permitted by this Software License and settle at its sole expense any amounts awarded in a final judgment or settlementresulting therefrom, under the condition that (i) you promptly notify Barco in writing after a claim has been asserted against you orthe commencement of any claim, action, suit or proceeding (whichever is the earlier), and (ii) Barco shall be allowed to assume solecontrol of the defense and any settlement negotiations related to any claim, action, suit or proceeding, and (iii) you shall not negotiate,settle or compromise any claim, action, suit or proceeding without the prior written consent of Barco and (iv) you, at your cost, shallcooperate with Barco and provide assistance and support, as may reasonably be required by Barco, in connection with the defenseand any settlement negotiations related to any claim, action, suit or proceeding. Barco shall have no indemnity obligation for anySoftware, or any portion thereof, (i) that is based on specifications, drawings, models or other data furnished by you or, (ii) that isnot provided by Barco or, (iii) that is modified, in spite of the prohibition for you to modify the software or, (iv) to the extent that youcontinue allegedly infringing activity after having been provided modifications that avoid the alleged infringement, or (v) where the useof the Software, or the combination or thereof with other Software, processes or materials or the distribution thereof rather than theSoftware itself is the primary cause of an alleged infringement. In case it has been determined by a finally awarded judgment thatBarco infringed or misappropriated such third party rights or earlier, at Barco’s discretion, it may, at its option and cost, (i) modify theSoftware in such a way that it shall not infringe upon or misappropriate the rights of the third party or (ii) obtain for you a license orother right to use the rights allegedly infringed or (iii) replace the Software in question with non-infringing Software. The remedies setforth in this paragraph shall constitute your sole and exclusive remedy and Barco’s sole and exclusive liability for a third party claimthat the Software infringes or misappropriates any intellectual property right of a third party.5. The duration of this Software License will be from the date of your acceptance (as set forth above) of the Software (whereby you ac-knowledge that use of the Software implies acceptance), with no termination date, unless otherwise specified. You may terminate thisSoftware License at any time by destroying all copies of the Software then in your possession and returning all associated materialsand documentation, to Barco or the appointed Barco reseller that sold or provided these to you. Barco may terminate this SoftwareLicense forthwith by informing you at any time if you and/or any Authorized User are in breach of any of the Software License’s terms.
6. YOU UNDERSTAND THAT THE SOFTWARE IS BEING PROVIDED TO YOU "AS IS". BARCO DOES NOT MAKE NOR INTENDSTO MAKE ANY WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIMS ALL IMPLIEDWARRANTIES OF MERCHANTABILITY FITNESS, FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF INTELLEC-TUAL PROPERTY AND DOES NOT WARRANT THAT THE SOFTWARE WILL BE FREE FROM ERRORS OR THAT SUCH ERRORSWILL BE CORRECTED BY BARCO AND YOU ARE SOLELY RESPONSIBLE FOR ALL COSTS AND EXPENSES ASSOCIATEDWITH RECTIFICATION, REPAIR OR DAMAGE CAUSED BY SUCH ERRORS.YOU ALSO ACKNOWLEDGE AND AGREE THAT:BARCO ACCEPTS NO LIABILITY FOR ANY DAMAGES, LOSSES OR CLAIMS YOU OR ANY THIRD PARTY MAY SUFFER ASA RESULT OF YOUR USE OF THE SOFTWARE. IN JURISIDCTIONS WHERE BARCO’S LIABILITY CANNOT BE EXCLUDED,BARCO’S LIABILITY FOR DIRECT DAMAGES SHALL BE LIMITED TO AN AMOUNT OF 250 EURO IN THE AGREGATE (OR TOTHE MAXIMUM EXTENT PERMITTED BY LAW WHERE NO FURTHER EXCLUSION IS LEGALLY ALLOWED).TO THE MAXIMUM EXTENT PERMITTED BY LAW, IN NO EVENT WILL BARCO BE LIABLE FOR ANY INDIRECT, SPECIAL,PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES OF ANY KIND WHICH MAY ARISE OUT OF OR IN CON-NECTION WITH THE SOFTWARE, THIS SOFTWARE LICENSE OR THE PERFORMANCE OR PURPORTED PERFORMANCEOF OR FAILURE IN THE PERFORMANCE OF BARCO’S OBLIGATIONS UNDER THIS SOFTWARE LICENSE OR FOR ANY ECO-NOMIC LOSS, LOSS OF BUSINESS, CONTRACTS, DATA, GOODWILL, PROFITS, TURNOVER, REVENUE, REPUTATION ORANY LOSS ARISING FROM WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION OF THE SOFTWARE AND ANY ANDALL OTHER COMMERCIAL DAMAGES OR LOSSES WHICH MAY ARISE IN RESPECT OF USE OF THE SOFTWARE, EVEN IFBARCO HAS BEEN ADVISED OF THE POSSIBILITY OF THEIR OCCURRENCE.YOU HEREBY AGREE TO INDEMNIFY, KEEP INDEMNIFIED, DEFEND AND HOLD HARMLESS BARCO AND BARCO’S AFFILI-ATES AND SUBSIDIARIES FROM AND AGAINST ANY AND ALL ACTIONS, PROCEEDINGS, LIABILITY, LOSS, DAMAGES, FEESAND COSTS (INCLUDING ATTORNEYS" FEES), AND OTHER EXPENSES INCURRED OR SUFFERED BY BARCO ARISING OUTOF OR IN CONNECTION WITH ANY BREACH BY YOU OF THE TERMS OF THIS SOFTWARE LICENSE.7. You shall treat as confidential all information obtained from the other pursuant to this Software License which is marked "confidential"or the equivalent or has the necessary quality of confidence about it and shall not divulge such information to any persons withoutBarco’s prior written consent provided that this Paragraph 7 shall not extend to information which was rightfully in the possession ofyou prior to the commencement of the negotiations leading to this Software License, which is already public knowledge or becomesso at a future date (otherwise than as a result of a breach of this paragraph 7), is required to be disclosed by law or which is trivial orobvious. You are aware of and ensure to comply with the provisions of this paragraph 7. The foregoing obligations as to confidentialityshall survive any termination of this Software License.8. You will remain responsible for the maintenance of your hardware, operating system, the functioning of your network and in keepingyour systems virus-free. You acknowledge that the Software is a complex computer software application, and that the performancethereof may vary depending hardware platform, software interactions and configuration. You acknowledge that the Software is notdesigned and produced specifically to meet your specific requirements and expectations and the selection of the Software by you isentirely your own choice and decision. For the avoidance of doubt, nothing in this Software License shall impose any obligation onBarco to provide support services (on the Software or any other hardware or software product).9. This Software License is the only understanding and agreement between you and Barco for use of the Software by you and/or Autho-rized Users. The Software License supersedes all other communications, understandings or agreements we had prior to this SoftwareLicense (with the exception of any continuing confidentiality agreement) although nothing in this Software License purports to excludeliability for fraudulent misrepresentation. You may not export or re-export the Software or any copy or adaptation in violation of anyapplicable laws or regulations. This Software License shall not be altered, amended or varied. If any provision of this Software Li-cense is determined to be illegal, void or unenforceable, or if any court of competent jurisdiction in any final decision so determines,this Software License shall continue in full force save that such provision shall be deemed to be deleted with effect from the date ofsuch decision, or such earlier date, and shall be replaced by a provision which is acceptable by law and which embodies the intentionof this Software License a close as possible.10. You acknowledge that this Software may be subject to U.S. or other governments Export Jurisdiction. You agree to comply with allapplicable international and national laws that apply to the Software, including the U.S. Export Administration Regulations, as well asend-user, end-use, and destination restrictions issued by the U.S. or other governments.11. Barco shall be entitled to sub-contract all or any of Barco’s obligations hereunder to a third party and/or any of Barco’s affiliatedcompanies.12. The construction, validity and performance of this Software License shall be governed in all respects by the laws of Belgium withoutrecourse to its conflict of law principles. All disputes arising in any way out of or affecting this Software License shall be subjectto the exclusive jurisdiction of the courts of Kortrijk, without prejudice to enforcement of any judgment or order thereof in any otherjurisdiction. The United Nations Convention on Contracts for the International Sale of Goods (the "Convention") shall not apply to thisSoftware License, however, if the Convention is deemed by a court of competent jurisdiction to apply to this Software License, Barcoshall not be liable for any claimed non-conformance of the Software under Article 35(2) of the Convention.Trademarks Software License TermsBrand and product names mentioned in relation to the Software may be trademarks, registered trademarks or copyrights of their respective(third party) holders. All such brand and product names mentioned in relation to the Software serve as comments or examples and are notto be understood as advertising for the products or their manufacturers.Privacy PolicyYou acknowledge and agree that the Software is gathering technical information about the functionality of the products which are connectedthrough the Software (“Functional Information”) and that Barco may make use of such Functional Information (with the exclusion of any
personal data) for any reason Barco sees fit, including but not limited to providing services to you / your organization, allowing third partyto access to such Functional Information and/or to provide services to you / your organization .You hereby explicitly give consent that Barco may gather, access, preserve, and/or disclose the personal data you provide to us (e.g.connected with your account allowing for the gathering of Functional Information as well as any content associated with that account) aswell as personal information we receive from you through the use of the Software:• For the benefit of the business purposes of Barco and/or its affiliates;• In order to provide, maintain, protect and/or improve the Software and to develop new software;• For administration of the relationship between you, your organization and Barco and/or its affiliates ;• For any other legitimate purpose (including i) direct marketing purposes from Barco, its affiliates or selected third parties, and ii)allowing third parties to provide services to you related to the Software);• if required to do so by law or in a good faith belief that such access preservation or disclosure is reasonably necessary to:- Satisfy any applicable law, regulation, legal process or enforceable governmental request;- Enforce this Software License, including investigation of potential violations hereof;- Detect, prevent, or otherwise address fraud, security or technical issues (including, without limitation, the filtering of spam);- Protect against imminent harm to the rights, property or safety of Barco, its users or the public as required or permitted by law.Barco shall not process any “sensitive information” whatsoever, including but not limited to medical information.You understand that the technical processing and transmission of or by the Software, including your content, may involve:• Transmissions over various networks;• Changes to conform and adapt to technical requirements of connecting networks, devices and/or services.You hereby explicitly give consent that Barco may export your personal data to any country worldwide, especially to any country whereBarco and/or its affiliates have infrastructure, or where a third party is making available infrastructure to Barco and/or its affiliates, to processpersonal data.Barco fully adheres to the EU Directive 95/46/EC on the protection of individuals with regard to the processing of personal data and thefree movement of such data, as implemented in the local EU member states. In accordance with these regulations, you have a right ofaccess to, and rectification of, your personal data. You may exercise these rights by contacting Barco.Open Source Software provisions:This product contains software components released under an Open Source license. A copy of the source code is available on requestby contacting your Barco customer support representative.EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTATION ARE PROVIDED "AS IS" WITH-OUT EXPRESS OR IMPLIED WARRANTY INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT, INCIDENTAL, SPECIAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POS-SIBILITY OF SUCH DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIA-BILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS OPEN SOURCESOFTWARE. MORE INFORMATION/DETAILS IS TO BE FOUND IN EACH SPECIFIC OPEN SOURCE LICENSE.Copyright on each Open Source Software component belongs to the respective initial copyright holder, each additional contributor and/ortheir respective assignee(s), as may be identified in the respective documentation, source code, README file, or otherwise. You shall notremove or obscure or otherwise alter the respective copyrights.You acknowledge living up to the conditions of each separate Open Source Software license.In the development of the Software, the following Open Source Software components have been used (an updated list may be madeavailable through the (customer section of the) Barco website or other (online) means):Open Source component Open Source Licenseacl http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlacpid http://www.gnu.org/licenses/gpl.htmlattr http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlhttp://www.gnu.org/licenses/gpl.htmlalsa-libhttp://www.gnu.org/licenses/lgpl.htmlhttp://www.gnu.org/licenses/gpl.htmlalsa-utilshttp://www.gnu.org/licenses/lgpl.html
Open Source component Open Source Licensehttp://www.gnu.org/licenses/gpl.htmlalsa-pluginshttp://www.gnu.org/licenses/lgpl.htmlavahi http://www.gnu.org/licenses/lgpl.htmlBootstrap (3.1.1) https://github.com/twbs/bootstrap/blob/master/LICENSEbootstrap-dialog https://github.com/twbs/bootstrap/blob/master/LICENSEbootstrap-slider.js v2.0.0 http://www.apache.org/licenses/LICENSE-2.0busybox http://opensource.org/licenses/GPL-2.0Chart.js https://github.com/nnnick/Chart.js/blob/master/LICENSE.mdDatepicker for Bootstrao (1,6,0-dev) http://www.apache.org/licenses/LICENSE-2.0dropbear http://opensource.org/licenses/mit-license.phpfakeroot http://www.gnu.org/licenses/gpl.htmlcoreutils http://www.gnu.org/licenses/gpl.htmlcrda http://opensource.org/licenses/ISCcron http://opensource.org/licenses/ISCCrypto++ http://www.cryptopp.com/License.txtdbus http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmldhcpd http://opensource.org/licenses/ISCdm-crypt http://creativecommons.org/licenses/by-sa/3.0/dmidecode http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmle2fsprogs http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmleglibc http://www.gnu.org/licenses/lgpl.htmlethtool http://www.gnu.org/licenses/gpl.htmlexpress http://opensource.org/licenses/MITFFmpeg http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmlhttp://freetype.sourceforge.net/FTL.TXTfreetypehttp://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlgdbserver http://www.gnu.org/licenses/gpl.htmlgmp http://www.gnu.org/licenses/lgpl.htmlgrub http://www.gnu.org/licenses/gpl.htmlgstreamer http://www.gnu.org/licenses/lgpl.htmlhdparm http://opensource.org/licenses/BSD-3-Clausehostapd http://opensource.org/licenses/BSD-3-ClauseHTML5 Shiv 3.7.2 http://github.com/aFarkas/html5shiv/blob/master/MIT%20and%20GPL2%20licenses.mdi18next (1.10.0) https://opensource.org/licenses/MITi2c-tools http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmliftop http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlimx-bootlets http://www.gnu.org/licenses/gpl.htmliperf http://opensource.org/licenses/BSD-3-Clauseiproute2 http://www.gnu.org/licenses/gpl.htmliptables http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
Open Source component Open Source Licenseiw http://opensource.org/licenses/BSD-3-ClauseJasny Bootstrap (3.1.3) http://www.apache.org/licenses/LICENSE-2.0jQuery Form Plugin (3.51.0-2014.06.20) https://github.com/malsup/form#copyright-and-licensejQuery JavaScript Library (1.11.3) https://jquery.org/license/https://github.com/ablanco/jquery.pwstrength.bootstrap/blob/master/GPL-LICENSE.txtjQuery Password Strength plugin forTwitter Bootstrap https://github.com/ablanco/jquery.pwstrength.bootstrap/com-mit/19480555e8c7c2f417d78a78dac63056fa221f6ajQuery Upload File Plugin (4.0.8) https://github.com/hayageek/jquery-upload-filejQuery Validation Plugin (1.13.1) https://opensource.org/licenses/MITkobs-ng http://www.gnu.org/licenses/gpl.htmllibarchive http://opensource.org/licenses/bsd-license.phplibav http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibavutil http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibcap2 http://www.gnu.org/licenses/gpl.htmllibdaemon0 http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibdrm2 http://opensource.org/licenses/MITlibexpat1 http://opensource.org/licenses/MITlibfontconfig1 http://opensource.org/licenses/BSD-3-Clauselibfontenc1 http://opensource.org/licenses/BSD-3-Clauselibgcc1 http://www.gnu.org/licenses/gpl.htmlhttp://www.gnu.org/licenses/gpl.htmlhttp://www.gnu.org/licenses/lgpl.htmllibgcrypt11http://www.gnu.org/copyleft/fdl.htmllibglib-2 http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibgnutls26 http://www.gnu.org/licenses/lgpl.htmlhttp://www.gnu.org/licenses/gpl.htmlhttp://www.gnu.org/licenses/lgpl.htmllibgpg-error0http://www.gnu.org/copyleft/fdl.htmllibjpeg-turbo http://opensource.org/licenses/BSD-3-Clauselibjpeg8 BSD like licenseelibnl2 http://www.gnu.org/licenses/lgpl.htmllibNotify https://wiki.gnome.org/FoundationBoard/Resources/LicensingAgreementlibnss-mdns http://www.gnu.org/licenses/gpl.htmllibpam http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmllibpcap http://opensource.org/licenses/BSD-3-Clauselibpcre0 http://opensource.org/licenses/BSD-3-Clauselibpixman-1-0 http://changelogs.ubuntu.com/changelogs/pool/main/p/pixman/pixman_0.10.0-0ubuntu1/libpixman-1-0.copyrightlibpng12-0 http://www.libpng.org/pub/png/src/libpng-LICENSE.txtlibpopt0 http://opensource.org/licenses/MITlibresample http://www.gnu.org/licenses/lgpl.html
Open Source component Open Source Licenselibsm6 http://metadata.ftp-master.debian.org/changelogs//main/libs/libsm/libsm_1.2.2-1_copyrightlibstdc++6 http://www.gnu.org/licenses/gpl.htmllibswscale http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibtalloc2 http://www.gnu.org/licenses/lgpl.htmllibusb http://www.gnu.org/licenses/old-licenses/lgpl-2.1.htmllibva Copyright (c) 2011, Advanced Micro Devices, Inc. All rights reserved.libX11 http://opensource.org/licenses/MITlibXdamage http://opensource.org/licenses/MITlibXext http://opensource.org/licenses/MITlibXfixes http://opensource.org/licenses/MITlibXinerama http://opensource.org/licenses/MITlibxml2 http://opensource.org/licenses/MITlibXrender http://opensource.org/licenses/MITlibXtst http://opensource.org/licenses/MITlibz1 Free licenselighttpd http://opensource.org/licenses/BSD-3-Clauselinux http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmllmsensors http://www.gnu.org/licenses/gpl.htmllogrotate http://www.gnu.org/licenses/gpl.htmlmakedevs http://www.gnu.org/licenses/gpl.htmlmemtest86plus http://www.gnu.org/licenses/gpl.htmlmesa http://opensource.org/licenses/MITmodernizr (3.1.0) https://opensource.org/licenses/MITmodule-init-tools http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlmodutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlmonit http://www.gnu.org/licenses/gpl.htmlncurses http://opensource.org/licenses/MITnetbase http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlnode.js https://raw.github.com/joyent/node/v0.10.26/LICENSEopenssl http://www.openssl.org/source/license.htmlopenssh-sftp-server http://opensource.org/licenses/BSD-3-Clauseopkg http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlpassport http://opensource.org/licenses/MITpassport-http http://opensource.org/licenses/MITpciutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlhttp://perldoc.perl.org/perlartistic.htmlperlhttp://www.gnu.org/licenses/old-licenses/gpl-1.0.htmlphp http://www.php.net/license/3_01.txtprocps http://www.gnu.org/licenses/gpl.htmlpulseaudio http://www.gnu.org/licenses/lgpl.html
Open Source component Open Source Licenseqt http://doc.qt.io/qt-5/lgpl.htmlread-edid Free licenseRespond.js https://github.com/scottjehl/Respond/blob/master/LICENSE-MITrockbox-imxtools http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlrsync (<3.0.0) http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlrsync (>=3.0.0) http://www.gnu.org/licenses/gpl.htmlrsyslog http://www.gnu.org/licenses/gpl.htmlsplashutils http://www.gnu.org/licenses/gpl.htmlsprintf-js https://opensource.org/licenses/BSD-3-Clausesscep https://github.com/certnanny/sscep/blob/master/COPYRIGHTstrace http://opensource.org/licenses/BSD-3-Clausesysfsutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlsysvinit http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmltcpdump http://opensource.org/licenses/BSD-3-ClauseTimepicker Component for TwitterBootstrap https://opensource.org/licenses/MITttf-arphic-uming http://ftp.gnu.org/non-gnu/chinese-fonts-truetype/LICENSEttf-dejavu-common http://dejavu-fonts.org/wiki/Licensettf-dejavu-sans http://dejavu-fonts.org/wiki/Licensettf-dejavu-sans-mono http://dejavu-fonts.org/wiki/Licensehttps://osdn.jp/cvs/view/efont/sazanami/READMEttf-sazanami-gothichttp://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-sazanami_20040629-8_copyright (translation)https://osdn.jp/cvs/view/efont/sazanami/READMEttf-sazanami-minchohttp://metadata.ftp-master.debian.org/changelogs//main/t/ttf-sazanami/ttf-sazanami_20040629-8_copyright (translation)ttf-un-fonts http://www.gnu.org/licenses/gpl.txtu-boot http://www.denx.de/wiki/U-Boot/LicensinguClibc http://www.gnu.org/licenses/lgpl.htmludev http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlupdate-modules http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlupdate-rc http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlusbutils http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlutil-linux-ng http://www.gnu.org/licenses/gpl.htmlwireless_tools http://www.gnu.org/licenses/gpl.htmlwpa_supplicant http://opensource.org/licenses/BSD-3-Clausexserver-xorg http://opensource.org/licenses/MITxvba-video http://www.gnu.org/licenses/old-licenses/gpl-2.0.htmlzeroconf http://www.gnu.org/licenses/gpl.htmlEN55022-CISPR22 Class B ITE (Information Technology Equipment)This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required totake adequate measures.
If this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of thefollowing measures :• Re-orientation of the receiving antenna for the radio or television.• Relocate the equipment with respect to the receiver.• Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.• Fasten cables connectors to the equipment by mounting screws.Federal Communication Commission Interference StatementYou are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’sauthority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.You ma y also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems." Thisbooklet is available from the U.S. Government Printing Office, Washington D.C. 20402.Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operatethis equipment under Federal Communications Commissions rules.In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approvedequipment or unshielded cables is likely to result in interference to radio & television reception.FCC RF Radiation Exposure Statement: This device is capable of operating in 802.11a mode. For 802.11a devices operating in thefrequency range of 5.15 - 5.25 GHz, they are restricted for indoor operations to reduce any potential harmful interference for Mobile SatelliteServices (MSS) in the US. WIFI Access Points that are capable of allowing your device to operate in 802.11a mode (5 .15 - 5.25 GHz band)are optimized for indoor use only. If your WIFI network is capable of operating in this mode, please restrict your WIFI use indoors to notviolate federal regulations to protect Mobile Satellite Services.Base Unit FCC ID: 2AAED-R9861510Button FCC ID (model R9861006D01): XF6-RS9110N1103Button FCC ID (model R9861500D01): 2AAED-R9861500D01ClickShare Button R9861500D01 has been tested and meets the FCC RF exposure guidelines.The maximum SAR value reported is0.915W/kg.Canada, Industry Canada (IC) NoticesThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) thisdevice may not cause interference, and (2) this device must accept any interference, including interference that may cause undesiredoperation of the device.Radio Frequency (RF) Exposure InformationThe radiated output power of the Barco Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The BarcoWireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.Base Unit IC ID: IC: 9393B-R9861510Button IC ID (model R9861006D01): 8407A-RS9110N1103Button IC ID (model R9861500D01): 9393B-R9861500D01IC Antenna statementUnder Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gainapproved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain shouldbe so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter 9393B-R9861510 has been approved by Industry Canada to operate with the antenna types listed below with themaximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, havinga gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Type: DipoleMaximum Peak Gain: 2 dBiImpedance: 50 OhmCanada, avis d’lndustry Canada (IC)Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation estautorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter toutbrouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Informations concernant l’exposition aux fréquences radio (RF)La puissance de sortie émise par l’appareil de sans fil Barco est inférieure à la limite d’exposition aux fréquences radio d’Industry Canada(IC). Utilisez l’appareil de sans fil Barco de façon à minimiser les contacts humains lors du fonctionnement normal.IC ID Unité de Base: 9393B-R9861510IC ID Button (modèle R9861006D01): 8407A-RS9110N1103IC ID Button (modèle R9861500D01): 9393B-R9861500D01Déclaration d’antenne d’Industrie Canada (IC)Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gainmaximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.Le présent émetteur radio 9393B-R9861510 a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérésci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus danscette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.Type: DipoleGain maximum: 2 dBiImpédance: 50 Ohm
Table of contentsTABLE OF CONTENTS1. Introduction ........................................................................................................ 31.1 Versions of the product .............................................................................................................. 31.2 About this guide ..................................................................................................................... 31.3 Symbols and fonts . . ................................................................................................................. 42. Introduction to CS-100 ........................................................................................... 52.1 About the CS-100 ................................................................................................................... 52.2 About the Base Unit ................................................................................................................. 62.3 About the Button..................................................................................................................... 72.4 Mobile Device Support .............................................................................................................. 83. Getting started..................................................................................................... 93.1 Activating the base unit.............................................................................................................. 93.2 Basic Use............................................................................................................................ 93.3 User Interface........................................................................................................................113.4 Capture more........................................................................................................................123.5 Shared desktop: primary - extended................................................................................................133.6 Audio configuration..................................................................................................................153.7 Pairing ...............................................................................................................................174. Troubleshooting .. ...... ...... ...... ...... ...... ...... .. .... .. ...... ...... ...... ...... .. .... .. .... .. ...... ...... ...194.1 Basic Troubleshooting ...............................................................................................................195. Environmental information ......................................................................................215.1 Disposal information.................................................................................................................215.2 Rohs compliance ....................................................................................................................215.3 Production address ..................................................................................................................225.4 Importers contact information .......................................................................................................22R5900024 CS-100 21/12/2014 1
Table of contents2R5900024 CS-100 21/12/2014
1. Introduction1. INTRODUCTIONOverview• Versions of the product• About this guide• Symbols and fonts1.1 Versions of the productRegional versionsDepending on the location where you buy the CS-100 product, the Base Unit and accessories are regionalized. By the time ofrelease of this manual, 3 regional versions of CS-100 are available:• Europe & Japan• North America• ChinaThe regional version of your CS-100 cannot be changed. That means that you cannot use it in another region.For more information on the regional variants, refer to the CS-100 Installation Guide.1.2 About this guideThis manualPartnumber Description LevelR5900024 User Guide UserAvailable System documentationThis guide is part of the documentation set describing the CS-100 product.Guide Article numberUser Guide R5900024Installation Guide R5900022Safety Guide R5900031Service Guide R5900026Button Guide R5900007Recycling Manual R5900028API Guide R5900018A printed copy of the Safety Guide and an electronic version on USB stick of the user and installation guide is included in the CS-100box at purchase.Always check for the latest version of the manual on www.barco.com/clickshare Click on Visit the ClickShareproduct page and go to tab Downloads..Depending on the CS-100 version, some graphics might be different to the ones used in this manual. Thishowever does not have any effect to the functionality.R5900024 CS-100 21/12/2014 3
1. IntroductionThe User Guide describes how to use your CS-100. It also contains a basic troubleshooting part where you can search for a solutionwhen a problem occurs.1.3 Symbols and fontsSymbol overviewThe following icons are used in the manual :CautionWarningInfo, term definition. General info about the termNote: gives extra information about the described subjectTip: gives extra advice about the described subjectFont overview• Buttons are indicated in bold, e.g. OK.• Menu items are indicated in italic.• Step related notes, tips, warnings or cautions are printed in italic.• Procedure related notes, tips, warnings or cautions are printed in bold between 2 lines preceded by the corresponding icon.4R5900024 CS-100 21/12/2014
2. Introduction to CS-1002. INTRODUCTION TO CS-100Overview• About the CS-100• About the Base Unit• About the Button• Mobile Device Support2.1 About the CS-100CS-100 setsCS-100 makes connecting to the meeting room’s video system a matter of clicking a Button. This CS-100 only helps the presenterget the presentation on-screen in a second, but it also allows the other people in the meeting to participate more actively. The resultis enhanced meeting efficiency and better decision-making.At the moment 3 different sets are available on the market. Each set is sold in its specific region and it can only be used in thatspecific region.Components CS-100 setA standard CS-100 set consists of a Base Unit and 1 Button. Depending on the location where you buy the product, the software ofthe Base Unit is different. If needed, you can buy additional Buttons.12Image 2-11 Base unit2ButtonAccessories includedDepending on the country where you buy the product, the following regionalized accessories are also included in the CS-100 box.Regional version Contains Accessories includedR9861510xx1• R9861510• 1x R9861500D01• DC adapter with AC clips type A, C,G, I• USB stick with user documentation• Printed safety manualContact your local sales representative for the correct regional variant to be used in your country.1. xx=EU, CN, NA,R5900024 CS-100 21/12/2014 5
2. Introduction to CS-1002.2 About the Base UnitBase Unit functionalityThe Base Unit receives the wireless input from the Buttons and controls the content of the meeting room display and the sound ofthe meeting room’s audio system.The Base Unit can be inside a cabinet in the meeting room, or put on the meeting room table or mounted on a wall. Check theInstallation Guide for instructions on how to install the Base Unit.213Image 2-21USB port2Status LED ring3 Power ButtonTabl e 2 -3USB PortThe USB port is used to update the software of both the Base Unit and the Buttons.When plugging in the Button into the Base Unit, the Button is paired to the Base Unit. The Base Unit checks whether the softwareand firmware of the Button is up to date. If not, the Base Unit updates the software and/or firmware.Status LED ringThe color of the LED ring around the power button of the Base Unit gives information on the status of the system.LEDs behavior Explanationstatic red• receiving content from the Buttons and streaming towards the display.• pairing and software update of the Button is done. You can now unplug theButton from the Base Unit.• during the first phase of the Base Unit boot process.blinking white• system is starting up (during the second phase)• Button pairing is in progress• software update of the Base Unitbreathing white• ECO standby mode• networked standby modestatic white• awake and ready (i.e. showing the welcome message on the display)• pairing is donered blinking• an error occurreddark• deep standby/offPower buttonThe button at the front of the Base Unit has a power on/off function once the Base unit is powered.• When the system is powered on, a push makes the system to shut down and power off.• When the system is shut down, a push triggers the system to start up.6R5900024 CS-100 21/12/2014
2. Introduction to CS-1002.3 About the ButtonButton functionalityA Button contains three main functional components.1 2 3Image 2-3The Button1 USB connector2Button3LEDringTabl e 2 -5Handle the Button cable with care. Rough handling might cause defects.USB connectorUsing the USB connector the Button can be plugged into a laptop (for sharing your screen) or in the Base Unit (for pairing the Buttonto the Unit or updating its software).ButtonClick the Button to display the content of the laptop’s screen on the meeting room display. Clicking the Button during the meetingwill toggle the sharing of the screen.LED ringThe LED ring indicates the current status of your CS-100.LEDs behavior Explanationwhite blinking• the Button is plugged in the laptop and initializing or waiting for the userto start the ClickShare application.• pairing/software update of the Button in the Base Unit is in progress.static white• ClickShare is ready to start sharing your screen.• pairing is done. You can now unplug the Button from the Base Unit.static red• sharing your screen with the display.• pairing and software update is done. You can now unplug the Buttonfrom the Base Unit.red blinking• an error occurred.off (no light)• the Button is not or not properly inserted into the USB port.• the Button might be defective.• the USB port or computer might be defective.R5900024 CS-100 21/12/2014 7
2. Introduction to CS-1002.4 Mobile Device SupportOverviewThe below list of Apps are supported by ClickShare and can be installed on your mobile device from Google Play or Apple App Store.Before you can use your mobile device with ClickShare, you have to connect the mobile device Wi-Fi with the ClickShare Base UnitWi-Fi. Follow the instructions as given in your mobile device user guide.App Used on LogoClickShare App iOSAndroidMirrorOp Sender for Galaxy Galaxy mobile devices8R5900024 CS-100 21/12/2014
3. Getting started3. GETTING STARTEDOverview• Activating the base unit•BasicUse• User Interface• Capture more• Shared desktop: primary - extended•Audioconfiguration• Pairing3.1 Activating the base unitAbout power modeThe Base Unit is powered via an external power adapter. Once connected, the Base Unit is automatically switched in standby mode.For more information about power connection, see CS-100’s installation manual.On and off1. Push the button shortly.Image 3-1Standby buttonWhen the Base Unit was on, it goes outWhen the Base Unit was off, it starts up.3.2 Basic UseBasic functionalityWhen entering a meeting room equipped with ClickShare and if the display is not in screensaver mode, the ClickShare wallpaper isshown on the display. The content of the wallpaper depends on the setup.Starting to use ClickShare is now very simple.To start using ClickShare1. Take a Button and Insert the Button into a USB port of your laptop.R5900024 CS-100 21/12/2014 9
3. Getting startedImage 3-2The LEDs of the Button start flashing white.On your laptop a new drive appears.Two situations are possible now:- A launcher is preinstalled on your laptop (downloaded from the Base Unit or Barco website, or deployed company-wide byyour IT department). ClickShare is immediately available. You can continue with step 4.- nothing is pre-installed. Continue with step 2.2. Browse to and double-click the ClickShare drive on your laptop.Image 3-3Windows environmentImage 3-4MAC environment3. Double-click the ClickShare application.10 R5900024 CS-100 21/12/2014
3. Getting startedThe ClickShare client software starts and its icon appears in the system tray.On a Windows computer:On a Macintosh:When the system is ready for use, a message appears close to the systray icon.Image 3-5The LEDs of the Button are static white.4. To share your screen on the display, click the Button.The LEDs of the Button become static red and your screen appears on the display. When audio is enabled on the ClickShareBase Unit, the audio of your laptop is also available on the audio output of the Base Unit and on the HDMI output, and it will beplayed via the meeting room audio system. The icon returns to the same state as in step 3.In the system tray, the ClickShare icon starts rotating. On Windows computers the icon changes into .The name of the user logged on to the laptop which is sharing its content is briefly shown in the bottom left corner of the addedcontent.ClickShare automatically scales the content of your screen to the resolution of the meeting room display. The aspect ratio of yourscreen is maintained to make sure the proportions are correct.5. To remove your content from the display, click the Button again.The LEDs of the Button become static white.6. When leaving the meeting room, unplug the Button from your laptop.No trace of the ClickShare application is left on your laptop.3.3 User InterfaceUser Interface functionalityAfter launching the client, the ClickShare icon appears in the system tray.ClickShare context menuThe content of the context menu is related to the operating system.1. Right-click the ClickShare icon in the system tray.The context menu appears.Image 3-6Context menu2. From the list, click the action you want to perform.R5900024 CS-100 21/12/2014 11
3. Getting startedClick To ResultStart sharing to show your screen on the display. The LEDs of your Button become red.Show me fullscreen to bring the content of your screen onthe display full screen.The screens of other users that wereshown on the display disappear.Settings... select the way to connect. ViaClickShare Button or via a networkconnectionConnected via Button or via networkPair Button to pair the connected Button with theBase UnitButton is ready for use.Capture mode to choose to capture video with more(slower performance) or less detail(faster performance).Tune video performance and qualityShared desktop (only for Windows7 andWindows8)to select primary or extended desktop Depending on the selection the primaryor the extended display is displayed.About ClickShare Client to find out the ClickShare softwareversion.Here you can find more information onthe ClickShare software version.Exit to close ClickShare. The ClickShare icon disappears fromthe system tray and the LEDs of theButton start blinking white.3.4 Capture moreOnly for Windows XP, Windows Vista and Windows 7 & 8.About capture moreClickShare is optimized for optimum video performance. Upon starting the client software it will disable Win7 Aero Glass to maximizevideo performance. Upon quitting the ClickShare applications your Aero Glass settings will be restored.Transparent alpha layers are by default not captured. Therefore some windows may not be shown or may appear different on screen.For example content of video players using overlays will not be shown.With "Capture More" selected, Win7 Aero Glass settings will be restored and capturing of alpha layers is enabled. In this mode,video throughput may decrease a bit and more details will be captured.Default setting: Not checked.How to change1. Right click on the ClickShare icon in the system tray (1).Image 3-7Change capture modeA context menu opens.2. Click Capture More to toggle.12 R5900024 CS-100 21/12/2014
3. Getting startedChecked: capture with more details but may have a lower performance.Not checked: capture will be faster but may lose some of the detailsStarting the client automatically in Capture MoreThe Capture more mode can be started by default so that the Aero Glass settings are not disabled. To do so, an environment variableshould be introduced in your windows. Ask you administrator or consult your windows documentation to find out how to create.The following variable should be introduced :Variable ValueCLICKSHARE_CAPTUREMOREBYDEFAULT 13.5 Shared desktop: primary - extendedOnly for Window7 and Windows8About shared desktopDepending on your selection, your primary screen or your extended screen will be captured and displayed via ClickShare. Thatextended screen can be a physical screen or a virtual screen.With extended desktop you can take advantage of both your laptop screen and the central meeting room display. Presentation notesor other material on primary screen will not be displayed to everyone.PC with virtual extended screen:12Image 3-8Primary screen displayed on the PC, extended screen displayed on the meeting room display.122Image 3-9PC with one extended screen connected. That extended screen will be captured and displayed on the meeting room display.R5900024 CS-100 21/12/2014 13
3. Getting started3122Image 3-10PC with two extended screens connected. The first extended screen, screen 2 will always be captured and displayed on the meetingroom display.To know if your system supports the extended desk top feature, press Window key + P. It should bring up thefollowing pop-up on screen:Image 3-11How to select1. Right click on the ClickShare icon in the system tray (1).Image 3-12Shared desktop selectionA context menu opens.2. Select Shared Desktop (2).3. Select the desired setting (3).Primary : the primary PC screen is displayed on the meeting room display.Extended always the secondary screen is displayed on the meeting room display.14 R5900024 CS-100 21/12/2014
3. Getting startedKnown issue• Virtual Extended Desktop not supported on some Windows7 and Windows8 systems due to a problem in recent versions ofthe AMD graphical driver. Downgrade to an older version of the driver might resolve the issue but make sure the AMD driverupdated above version 13.8 .3.6 Audio configurationAudio configurationThe connected user must control his own audio signal using the audio configuration of his computer. If he does not want to broadcasthis audio signal, he has to mute audio on his computer.For some operating system, it is necessary to set ClickShare as your default output device. Once you unplug the Button, the defaultsetting is switched back to the previous setting.Set ClickShare as default in Windows 71. Right click on the speaker icon in the system tray (1).Image 3-13Speakers ClickShare, default2. Click Playback devices (2).The Sound window opens on the Playback tab.3. Select Speakers ClickShare (3) and click Set default (4).4. Click Apply or OK to activate the new setting.Set ClickShare as default in Windows XP1. Right click on the speaker icon in the system tray.R5900024 CS-100 21/12/2014 15
3. Getting startedImage 3-14Speakers ClickShare, default2. Click Adjust Audio Properties (1).The Sound and Audio Devices Properties window opens.3. Select Audio tab (2).4. Click on the drop down box in the Sound playback pane and select ClickShare (3)..5. Click Apply or OK to activate the new setting.Set ClickShare as default on MAC1. Click on the Apple logo on the menu bar (1) and select System Preferences.. ..(2).16 R5900024 CS-100 21/12/2014
3. Getting startedImage 3-15Speakers ClickShare, default2. Click on the Speaker icon (3).The Sound window opens.3. Select the Output tab (4) and activate ClickShare (5).3.7 PairingPairing of the Buttons with the Base UnitTo be able to use a Button it should be assigned to the Base Unit you are using. This process is called pairing. By default, the twoButtons delivered with the CS-100 set are already paired to the specific Base Unit.In case you buy additional Buttons or when a Button should be assigned to another Base Unit, the Button needs to be paired (again).The Button software update runs in the background and will not impact users while using the system. If desired, this feature canbe disabled in the Web Interface. When downgrading or updating to an older version of the Base Unit software the Buttons need topaired manually to update their software.A Button can only be paired to one Base Unit at a time.The Button will always make connection to the Base Unit it was last paired to.To pair a Button to the Base unit1. Insert the Button in the USB port at the front of the Base Unit you are using.R5900024 CS-100 21/12/2014 17
3. Getting startedImage 3-16Pair buttonBoth the LEDs of the Button and the LEDs of the Base Unit are blinking white. This means pairing is in progress.The Base Unit automatically checks whether the software of the Button is up to date. If not, the Base Unit updates the Buttonsoftware. This may take more time.During the pairing and update process, a small status bar is display.Image 3-17Pairing messageThe result of the pairing process can be as follows:- When the LEDs become static white, the Button is paired to the Base Unit, but no software update was needed. You canunplug the Button from the Base Unit.- When the LEDs become static red, the Button is paired to the Base Unit and the software update has finished. You can unplugthe Button from the Base Unit.Image 3-18Pairing finished2. Unplug the Button from the Base Unit.The Button is now ready for use.18 R5900024 CS-100 21/12/2014
4. Troubleshooting4. TROUBLESHOOTING4.1 Basic TroubleshootingProblem solvingIn this chapter some problems that might occur while using CS-100 are listed. For each problem possible causes are given and asolution is proposed. If you cannot solve the problem yourself, please contact your local IT administrator.Problem Cause SolutionYou are the second person that wants toshare the content to the display.The first user has to push his button toremove his content so that a second usercan share his content. orAs second user, click and hold the Buttonto use te Show me function of ClickShare.Your screen is not shown on the displaywhen pressing the Button.The ClickShare client software is notrunning.Go to the ClickShare drive and run thesoftware.Your audio signal on your PC is muted Right click on the speaker icon and switchoff the mute.Audio system of the meeting room is notswitched onSwitch on the audio system of themeeting room.When using separate audio, audio cableis not connectedCheck audio connection between theBase Unit (audio out, green connector)and the audio system of the meetingroom.Default speaker is not correctly set . With a Button inserted, set ClickSharespeaker as your default speaker.Your screen is shown, but your audio isnot playing on the meeting room audiosystemButtons are not re-paired after changingthe audio setting on the web interfaceRe-pair the buttons.Your content is removed from the displayand the LEDs of your Button are blinkingwhite.Connection to the display has been lost. ClickShare tries to restore the connectionautomatically. If this fails, the LEDs ofthe Button start blinking red. You shouldunplug the Button from your laptop andstart a new.The display is switched off. Switch on the display.Wrong input is selected. Select the correct input.The display cable is not connected(correctly).(Re)insert the display cable to the displayand the Base Unit.The display does not recognize or isnot able to display the Base Unit outputresolution.You or an administrator should changethe corresponding setting via the webinterface.The Base Unit is in standby mode. Briefly push the standby button on theBase Unit or plug in a Button and run theClickShare client software.The Base Unit is powered off. Check if power adapter is connected tothe Base unit and to the wall outlet.Nothing is shown on the display at all.The Button’s software is not compatiblewith that of the Base unitRe-pair and update the software of theButton by inserting it in the front USB portof Base Unit.R5900024 CS-100 21/12/2014 19
4. TroubleshootingProblem Cause SolutionNo automatic refresh of drives. Refresh the view on your laptop.Bad connection at USB port on laptop.• Reconnect to the USB port.• Try another USB port.• Reboot your laptop.After inserting the Button into your laptop,you cannot find the ClickShare drive.Windows tries to assign the ClickSharedrive to an already reserved drive letterUse Microsoft Windows DiskManagement to assign it to a freedrive letter.Some programs of Windows are notshown on the display.Use of overlays, 3D or hardwareacceleration in the GPU. • Disable overlays or hardwareacceleration in the GPU.• Disable AeroGlass in Windows 7• Capture mode20 R5900024 CS-100 21/12/2014
5. Environmental information5. ENVIRONMENTAL INFORMATION5.1 Disposal informationDisposal InformationWaste Electrical and Electronic EquipmentThis symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical andelectronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment byhanding it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possibleharm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources.For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weeeDisposal of batteries in the productThis product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separatelyfrom municipal waste.If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols willappear below the crossed-out wheeled bin symbol.By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effectson the environment and human health.5.2 Rohs complianceTurkey RoHS complianceTürkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.[Republic of Turkey: In conformity with the WEEE Regulation]中国大陆RoHS – Chinese Mainland RoHS根据中国大陆《电子信息产品污染控制管理办法》(也称为中国大陆RoHS), 以下部分列出了Barco产品中可能包含的有毒和/或有害物质的名称和含量。中国大陆RoHS指令包含在中国信息产业部MCV标准:“电子信息产品中有毒物质的限量要求”中。According to the “China Administration on Control of Pollution Caused by Electronic Information Products” (Also called RoHS ofChinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product maycontain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in thesection “Limit Requirements of toxic substances in Electronic Information Products”.零件项目(名称)Component Name有毒有害物质或元素Hazardous Substances or Elements铅(Pb)汞(Hg)镉(Cd)六价铬(Cr6+)多溴联苯(PBB)多溴二苯醚(PBDE)印制电路配件Printed CircuitAssembliesx0x000电(线)缆Cablesx0x000R5900024 CS-100 21/12/2014 21
5. Environmental information底架Chassisx0x000电源供应器Power Supply Unitx0x000文件说明书Paper Manuals000000这个表被制备按照规定SJ/T 11364This table is prepared in accordance with the provisions of SJ/T 11364.O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下.O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limitrequirement in SJ/T11363.X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 标准规定的限量要求.X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this partis above the limit requirement in SJ/T11363.在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子信息产品污染控制标识要求》标准贴上环保使用期限(EFUP)标签。Barco产品所采用的EFUP标签(请参阅实例,徽标内部的编号使用于制定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准。All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the “Electronic Information ProductsPollution Control Labeling Standard” of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. Thenumber inside the EFUP logo that Barco uses (please refer to the photo) is based on the “Standard of Electronic Information ProductsEnvironmental Friendly Use Period” of Chinese Mainland.Image 5-15.3 Production addressFactoryBarco N.V.12F, Citychamp Building, No. 12, Tai Yang Gong Zhong Lu, Chaoyang District, Beijing, P.R.CMade in informationThe made in country is indicated on the product ID label on the product itself.Production dateThe month and year of production is indicated on the product ID label on the product itself.5.4 Importers contact informationContactTo find your local importer, contact Barco directly or one of Barco’s regional offices via the contact information given on Barco’s website, www.barco.com.22 R5900024 CS-100 21/12/2014

Navigation menu