Beautiful Light Technology CMLAMP IP Camera Lamp User Manual IPCMLAMP EN

Beautiful Light Technology Corporation IP Camera Lamp IPCMLAMP EN

Users Manual

1產品介紹Before installationRead the following guidelines before installation:• Avoid covering the front of the camera to ensure the view can be captured completely.One third of the lamp needs be exposed outside of the fixture to allow enough view and light.• Keep the power of the unit and the Router on in order to monitor through the use of APP remotely.Equipment requirement:• To make sure the APP to operate smoothly, it is recommended to use smart device with quad-core processor with 2G RAM and up. • Support iOS 8.0 and up、Android 4.4 and up.• Support WPA and WPA2, WEP is not supported. • Network bandwidth upload speed is 10Mb or above, to keep the system stability.• Disable Router firewall before use.• Please set the Router to a fixed channel, to improve Internet stability.• Ensure the Wi-Fi signal is strong and close to desired socket location. (Within 10 meter distance or in the same room)Friendly remindersIf you buy more than one IP C.M. Lamp, it’s highly recommended to install one lamp at one me, and write down the posion or unit name on the device card to avoid mixing up the unit UID.
2Connection stepStep 2Turn on unit powerStep 3Add new unit 45 seconds later lamp initialization copelet(lamp wll flash one time, brighteness set to 50%)Start connecting the unit to your smart device.C.M. Lamp +Click to +add new unitStep 1Download APP based on your operating systemStep 4 Choose the connection wayIf there is WiFi in the room,choose (page 3 )If there is no WiFi in the room,choose (page 4)Additional user, choose (page 5)Router connectionDirect connectionAdded device connection
3Router connection stepONKeep power on27Enter Wifi passwordclick [Continue]Click [Add new unit]Choose the unityou wish to connectAfter connection successfullyName the unitEnter device passwordAfter completion enter to the control interface automatically.Wait for the connectionto establishHOME WiFiTP-LINK WiFiTP-LINK2 WiFiTurn on WiFi Connect the router near the unitNotice If connection fail, reboot the unit and the router before re-connect.If connection fail, check smart device WiFi connect the router or not.Within 10 meter distance or in the same room
4Direct connection stepNotice If unit connected with router, C.M. Lamp_xxxx will hide, couldn’t be search,after turn the router off, or change the unit site, out of router coverage,C.M. Lamp_xxxx can be detection again.After connection, change the unit password , into [setting]-[unit password]27Click Connection completedClick [ unit has been added]C.M. Lamp_xxxxxxTP-LINK WiFiTP-LINK2 WiFiTurn on WiFiConnect [CM Lamp_xxxxxxx]Click the QR Code iconscan your unit QR CodeKeep within 10 meter of unit or in the same room while connectingONKeep power onUID and Password will be input automaticallyClick and go back to unit listThe icon in front of the unit name : Connected Not connected
5Added unit connection step This connection way is for additional user27HOME WiFiTP-LINK WiFiTP-LINK2 WiFiONKeep power onTurn on WiFi Connect the router near the unitAfter connection, change the unit password , into [setting]-[unit password]NoticeUID and Password will be input automaticallyClick Connection completedClick [ unit has been added]Click the QR Code iconscan your unit QR CodeClick and go back to unit listThe icon in front of the unit name : Connected Not connected
6Homepage and settingNote : If delete the unit by accident,and not reset yet,Go to [add unit] -[unit has been added] to auto search connected unit.HomeConnection statusNot connected----BlackConnecting----PinkConnected----RedDelete unitScroll right----delete unitScroll left----turn off delete bar
7Homepage and settingRecord listEnter date, search specific video by date (each video is 5 mins)PowerRecord listSettingAdd unitClickinto control interfaceHome• If the recording type is fullme, it can record about 7 days. Recording periods depend on the environment.• It will recover former records when the storage of memory card is full.• In fullme recording status, the scene might be flat or black while you click the recording video. The scene will resume normal aer recording is down (5 mins).• Video playback bar, watch the video record me precisely.
8SettingNoticeAfter initial set up, it is highly recommended to change the default unit name and password, and to change the password periodically.Change password SettingUnit name(click to edit）Unit detailNotificationNight light settingUser manualChange password
9Unit settingNotice After initial set up, it is highly recommended to change the night light set up.Connect to IP C.M. Lamp APP Manual website.When the light turn off and the Ambient lightless than 6lx,Nightlight will turn on automatic.User manualNight light setting
10Unit detailNotice After initial set up, it is highly recommended to change the recording mode set up.Unit image(show on homepage) Choose from album take a snapshot frome phoneRecording type(Files will be saved in record list) Off Fulltime EventUnit resetReset all the setting of Unit.Format the SD cardAll record will be delete.Unit detail
11Push Nofications When IP C.M. Lamp detects any motion, App will send push notification, user can watch the scene of home immediatelyTurn on push noficationsPlease keep the QR code for future re-configurationIP C.M. LAMP QRCODEPlace111100123ANotification function shows SSIDiOS user can receive push nofications only when APP is closed.Android user can receive push notifications Whether the app is open or close.[setting] - [device detail] - [Recording type]choose [ Fulltime] or [Event]
12Unit Reset１.App Operation [Setting] - [Unit detail] - [RESET] when light blinks for 3 times,then reset successful.2. Manual Operation Make sure the unit power on 5-10 seconds,then power off, repeat the step 4 times, then turn on power, when light blink 3 times, then reset successful.Unit reset, if you reset all the setting of unit, and all the connected smart device will be not-connected. Notice
13Control interfaceFlipsMuteUnmuteBrightness adjustmentSnapshot / on time recordingViewing angle adjustmentMute(Files will archive in your smart device)360°
Brightness adjustmentent14Scroll the bar left and right to adjestment brightnessTurn on the power
15Snapshot / RecordingSnapshot RecordingNotice Image Archive must have authorization to have access to the photosreminder to adjust the setting and to allow APP to have access.Files will be saved in your smart device
16Viewing angle adjustmentSplit modescroll right and leftFisheye modescroll right and left or zoom in and outPanoramic VR modescroll right and left or zoom in and outRotate smart device, switch to full screen mode.
17To flip the screenFlip vertically
18Common problems1. Why the router connection always fail?ans. Please check the WiFi is connected to the correct router, and keep the connection stable.2. How to deal with unit disconnection?ans. First, check the WiFi connection status, if it still fail, reboot the device, router and the app.3. If I forget the unit password?ans.If user forget the unit password or change other router connection, reset the unit.4. How many smart device can connect with a C.M. Lamp?ans.It depends on Network environment.5.How many C.M. Lamp can connect to a smart device?ans. Unlimited.6. How to reset unit?ans.[Setting]-[Unit detail]-[Reset]
19Router channel setting參考網址: http://www.tp-link.tw/faq-78.htmlPlease set the Router to a fixed channel, to improve Internet stability.192.168.1.1Step1 Open a web page,enter router IP URL(preset is 192.168.1.1)Step2 Enter the user name and password(preset name and password is [admin] )Step3 Click on left side[wireless]-[wireless setting]Wireless SettingSSID:Region:Channel:Waring: Ensure you select a correct country to conform local law. Incorrect setting may cause Interference.Enable Wireless Router RadioEnable SSID BroadcastTP-LINKTaiwan6Step4 Wireless setting (take TP-LINK for example，FIG.)SSID ：enter router name Region ：select your country .Channel ：choose the wireless channel.(Enable Wireless Router Radio/Enable SSID Broadcast this two option always enable)Step5 Click [Save] to save setting。Notice ：If there is too many wireless signal on the same channel, change to another one to improve WiFi signal.Android user,download [Wifi Analyzer]appaccroding to network environment ,choose the proper wireless channel.iOS user,download [Airport]appaccroding to network environment ,choose the proper wireless channel.
Firewall setting20Disable Router firewall - <Forwarding> - <Basic Security> - <Firewall> Take TP-LINK for exampleDue to firewall of router would block the P2P connecon and then smart device couldn’t connect with IP C.M. Lamp. If the original router needs firewall, it’s highly recommended to set up another router only for IP C.M. Lamp, disable firewall and set the router to a fixed channel.
Regulations21Federal Communications Commission (FCC) StatementYou are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device.(WIFI) For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operatingin conjunction with any other antenna or transmitter.

Navigation menu