Behavior Tech Computer KB9019URF3 Wireless Keyboard User Manual Manual

Behavior Tech Computer Corporation Wireless Keyboard Manual

Manual

    9019URF3 Quick Installation Guide Important Information For more detailed information, please refer to the Help file in the Driver CD in the Help directory. The ways to display the Help file are as follows: -  After driver installation, please click the driver icon at the right-bottom in the Windows system tray. Click the Help button on the left-bottom of the driver Configuration dialog box and the help file will pop up. Or -  Please see “Help\ Help.htm” in the Driver CD. Hardware Installation                Front View of            Back View of  USB Connector          USB Connector      (-)(+ ) 1.  Plug in the dongle receiver connector into your available USB port on PC.2.  Make sure the batteries of the keyboard are installed correctly. Please follow the polarity signs in the battery compartment. ID Pairing Procedure After you plug the receiver USB connector into your PC USB port, please hold the keyboard close to the receiver within 1M and press any keys to pair ID. If it can’t work, please follow the steps below to process the ID pairing procedures of the Wireless Kit. The ID-recognition function helps to protect against interference from other RF products in the same environment. Remember to follow the steps below to change ID when other RF products affect your keyboard kit.  ID pairing/connect button location: -  Receiver ID pairing/connect button→  on the top of the dongle receiver-  Keyboard ID pairing/connect button→  on the top of the keyboard  ID pairing procedures: 1. Press and hold the ID pairing/connect button on the top of the dongle receiver at least 10 seconds until the receiver LED flashes 3 times. The receiver LED will flash 60 seconds to wait for keyboard pairing information. (If you release the button within 10 seconds, the ID doesn’t make any changes.) 2.  Hold the keyboard close to the dongle receiver within 1M. 3. Press and hold the keyboard ID pairing/connect button on the top of the keyboard at least 10 seconds until the keyboard LED flashes once. (If you release the button within 10 seconds, the ID pairing will fail.) 4. The receiver LED indicator flashes 3 times rapidly as indication its’ ID paired with this keyboard. Then you could press any keys to check if the keyboard works or not.     Mouse Middle ButtonMouse Right ButtonMouse Left ButtonScroll DownScroll UpStickerID Button(LED) Note: - Make sure your PC is on and running when doing the pairing procedure. - You don’t have to pair ID again after changing batteries. If it can’t work, please follow the steps above to pair ID. Battery Low Alarm When the keyboard batteries are low, the keyboard ID pairing/connect button will blink when you press keyboard buttons. Please change batteries immediately when the RED LED indicator lights up to ensure the good use of this keyboard. After you change the batteries, the RED LED indicator will disappear. Driver Installation   USB Device Driver The USB device driver is included with your Windows operating system.     During the initial installation of the keyboard USB device, the system will automatically detect that a new hardware device has been added and will bring up the "Add New Hardware Wizard" dialogue box. Follow the Wizard's USB driver installation steps. Once this installation step is completed, the basic functions of the USB device will work under the operating system. The additional functions are provided only after the KeyMaestro driver is installed.    KeyMaestro Input Device Driver 1. Insert the CD labeled "KeyMaestro Input Device Driver" into your CD-ROM. 2. The CD will automatically run and bring up the Setup dialogue box. 3. Follow the on-screen instructions to install the driver. 4. The driver icon    will show at the right-bottom of the Windows system tray when the driver is loaded. ID pairing/connect button on the top of the keyboard ID pairing/connect button on the top of the dongle receiver (With a LED indicator under the ID pairing/connect button) English
   Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu