Behavior Tech Computer MSM996 CORDLS LSR MOUSE FOR NOTEBOOKTM User Manual M996 Labtec QIG

Behavior Tech Computer Corporation CORDLS LSR MOUSE FOR NOTEBOOKTM M996 Labtec QIG

User manual

MM--RRCCTT115500//CC--UUBBHH6688 QQuuiicckk IInnssttaallllaattiioonn GGuuiiddee System Requirements - Microsoft® Windows® ME, Windows® 2000, Windows® XP or Windows Vista® operating system - CD-ROM drive - Standard sound card - Microsoft Office 97 or later version - Microsoft Internet Explorer 5.0 or later version - Available USB port Hardware Installation 1. Plug in the receiver connector into your available USB port on PC. 2. Make sure the batteries of the mouse are installed correctly, please follow the polarity signs in the battery compartment. Pairing Procedure After you pair mouse with the receiver, you can operate the mouse immediately. The pairing button locates on the top of the receiver with a LED under to show the pairing or data reception status. By pairing the wireless mouse with receiver it will: - Generate a new digital ID, linking uniquely mouse with receiver. This lessens inference from nearby wireless products. 1. Press the pairing button on the top of the receiver first. 2. Next, press the pairing button on the bottom of the mouse once. 3. The receiver LED will blink rapidly for some time to indicate it has received pairing information. 4. When you move the mouse, the receiver LED will light steadily. When you stop using the mouse, the receiver LED will stop lighting. Note: 1. Your PC must be turned on before doing this pairing procedure. 2. You must follow the procedure above to complete ID pairing. 3. The whole procedure should be completed within 60 seconds. Battery Information 1. We recommend using alkaline batteries for a longer battery life. 2. Always change batteries when battery low alarm indication appears. 3. Install mouse driver first to ensure the battery power is monitored. 4. Don't mix different types of batteries or new and old batteries together. Always replace old batteries with new and same type batteries. 5. Remove batteries after long periods of non-use. Battery leakage or corrosion may damage the device quality and cause danger. 6. Mouse Information 1. This laser mouse can work on most surfaces, including polished or wood-grain surfaces. 2. While functioning, this mouse emits invisible laser light that may be hazardous to eyes. Avoid looking directly into the emitter hole on the bottom of the mouse. Laser Safety Information This product complies with International Standards EN 60825-1/A2: 2001, Class 1 Laser Product, and also complies with FDA standards Title 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No.50, dated July 26, 2001. Pairing button on the top of the receiver (With LED under the pairing button) Pairing button on the bottom of the mouse
FCC GUIDELINES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.  Use only shielded cables to connect I/O devices to this equipment. FCC Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Information to user: The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment is intended for use in the following countries EU 18 countries: Austria, Belgium, Denmark, Finland, France, Germany, Ireland, Italy, Luxembourg, Netherlands, Spain, Sweden, United Kingdom, Portugal, Greece, Switzerland, Norway, and Iceland. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This Category II radiocommunication device complies with Industry Canada Standard RSS-310. Ce dispositif de radiocommunication de categorie II respecte la norme CNR-310 d’Industrie Canada.

Navigation menu