Behringer V Tone Acoustic Driver Di Adi21 Users Manual
Behringer-V-Tone-Acoustic-Driver-Di-Adi21-Owners-Manual behringer-v-tone-acoustic-driver-di-adi21-owners-manual
ADI21 to the manual c5a66125-7ea0-4faf-96df-c56a16161b15
c5a66125-7ea0-4faf-9.. c5a66125-7ea0-4faf-96df-c56a16161b15
2015-06-29
: Behringer Behringer-V-Tone-Acoustic-Driver-Di-Adi21-Users-Manual-753178 behringer-v-tone-acoustic-driver-di-adi21-users-manual-753178 behringer pdf
Open the PDF directly: View PDF .
Page Count: 2
V-TONE ACOUSTIC DRIVER DI ADI21
Acoustic Amp Modeler/Direct Recording Preamp/DI Box
Thank you for showing your condence in us by purchasing the V-TONE
ACOUSTIC ADI21. This high-quality acoustic guitar driver is designed for all
acoustic guitar players who are looking for more sounds to reach maximum
exibility and creativity. Thanks to its high-performance EQ section
(including parametric mids) and the integrated Tube/Microphone Emulation,
the ADI21 gives your guitar natural sound with smooth saturation, just as if it
were being miked. In addition, the ADI21 functions as a standard ultra-transparent
direct injection box when used in bypass mode.
A DI (Direct Injection) box allows you to send a signal directly from an unbalanced,
high-impedance output (like an electric guitar) and connect it directly to the
balanced mic input of a mixing console.
Whether for stage, recording, rehearsal or warm-up, BEHRINGER’s V-TONE ACOUSTIC
ADI21 is a natural choice for those who are seeking great tone with a simple set-up.
1. Control Elements
Control elements
(1) The TREBLE control governs the high-frequency range of the signal (±12 dB).
(2) The BASS control allows you to boost/cut the low-frequency range (±12 dB).
(3) Use the MID control to boost or cut the mid-range frequencies (±12 dB).
The MID FREQ control lets you select the middle frequency (170 Hz to 3.5 kHz)
that will be boost/cut.
(4) The LEVEL control adjusts the output level of the ADI21.
(5) The BLEND control activates the integrated tube/microphone emulation circuitry.
In most cases, you will probably set it to maximum (100%). If you want to
hear some of the distinct timbre of a piezo pickup or reduce the amount
of compression, simply turn the control counterclockwise.
(6) When activated, the GND LIFT disconnects the ground connection between
input and output. Depending on the grounding of the connected equipment,
this can eliminate hum or ground loops.
(7) The -20 dB PAD switch attenuates the output level of the BAL OUT (see (10))
by -20 dB. It should be activated when the output level is too high for the
microphone input of the mixer channel.
◊ Before using the PAD switch, be sure that it is the mic preamp on the
mixing console that is clipping and not the ADI21. You should only
attenuate the output signal via the PAD switch if the CLIP LED of the
mic channel lights up frequently or remains lit.
(1)
(8)
(5)
(4)
(3)
(2)
(6)
(9)
(7)
(8) Use the footswitch to activate/deactivate all the tone functions
(EQ, microphone/tube emulation). When deactivated, the ADI21
functions solely as a standard transparent DI box.
(9) This LED illuminates when the eect is activated (see (8)).
Connectors
(10) Use this ¼" TS INPUT connector to plug in the instrument cable of your
acoustic guitar or other instruments.
(11) BAL OUT is the ADI21’s balanced mic level output. Use a high-quality,
balanced XLR (microphone) cable to connect the driver to a mixing console.
(12) The unbalanced ¼" TS OUT connector sends the signal to your guitar amp.
Bottom of the ADI21
(13) SERIAL NUMBER. The serial number of the ADI21 is located at the bottom.
(14) BATTERY COMPARTMENT. Open the lid to install or replace the 9 V battery.
◊ The ADI21 is powered as soon you insert a plug into the INPUT.
The battery is “disconnected” when the plug is removed.
For this reason, the ADI21 has no on/o switch. To prolong
battery life, always disconnect the input when the driver is
not in use.
(15)
Power supply connector
(15) Use the DC IN connection to plug in a 9 V power supply (not included).
(10) (12)
(11)
(14)
(13)
V-TONE ACOUSTIC DRIVER DI ADI21
TECHNICAL SPECIFICATIONS AND APPEARANCES ARE SUBJECT TO CHANGE WITHOUT NOTICE AND ACCURACY IS NOT GUARANTEED. BEHRINGER IS PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN
PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED
FULLFILLERS AND RESELLERS ONLY. FULLFILLERSAND RESELLERS ARE NOT AGENTS OF MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED UNDERTAKING
OR REPRESENTATION. THIS MANUAL IS COPYRIGHTED. NO PART OF THIS MANUAL MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRONIC OR MECHANICAL, INCLUDING PHOTOCOPYING
AND RECORDING OF ANY KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS WRITTEN PERMISSION OF MUSICGROUPIPLTD. ALL RIGHTS RESERVED. © 2012 MUSICGroupIPLtd. Trident Chambers,
Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands
2. Safety Instructions
Do not use near water, or install near heat sources. Use only authorized
attachments/accessories. Do not service product yourself. Contact our qualied
servicing personnel for servicing or repairs, especially when power supply cord or
plug is damaged.
3. Warranty
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
4. Specications
Input
Connector ¼" TS
Impedance 1 MΩ
Output
Connector ¼" TS
Impedance 1 kΩ
Balanced output
Connector XLR
Impedance 200 Ω
Power supply 9 V, >50 mA DC regulated
Power connector 2 mm DC jack, negative center
Battery 9 V type 6LR61
Power consumption 25 mA
Dimensions/Weight
Dimensions (H x W x D) approx. 5 x 3 ⁄ x 2"
approx. 127 x 100 x 50 mm
Weight approx. 1.01 lbs / 0.46 kg
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of
these efforts, modifications may be made from time to time to existing products without prior notice.
Specifications and appearance may differ from those listed or illustrated.
5. Sample Settings
FOLK
COUNTRY
FINGER PICKING
JAZZ
ELECTRIC GUITAR (semi dirty)
BASS GUITAR