Beijing Jia An Electronic Technology Co BTRS BLE module User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	2982742
Application ID	la9Y+rve9bhh1/8tE810uw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.11kB (326357 bits)
Date Submitted	2016-05-09 00:00:00
Date Available	2016-05-09 00:00:00
Creation Date	2016-04-26 10:30:03
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-04-26 10:30:04
Document Title	Slide 1
Document Author:	Jonathan Frank

Installation Set-up Guide
Mode Descriptions & System Layout
Device Description
CarLink BT allows users to remotely access their vehicle by Bluetooth connection. There are 3 types
of installations:
1. Standard Installation (MODE 1): Use standalone with a remote start or alarm system or in parallel
with a Flashlogic Interface (FLCAN).
2. Flashlogic Remote Start (MODE 2): This mode is used with any FLRS kit or FLCAN programed with
‘RS’ firmware.
3. Virtual Transmitter (MODE 3): Allows CarLink BT to directly control a Flashlogic DOOR LOCK
Interface Module. This would allow smart phone control to any factory system.
MODE 1
Standard Installation (MODE 1): This utilizes the iDatalink protocol on both ports so this system can
be added in parallel with a Flashlogic Interface (i.e. FLCAN) or used standalone when plugged into
DBI port for smartphone control. In this mode, data traffic is passed through between both ports.
This will be the most common MODE when used with any Audiovox branded remote start.
Mode Descriptions & System Layout
MODE 2
Flashlogic Remote Start (MODE 2): This utilizes the Flashlogic RF protocol on both ports so this
system can be added in parallel with an optional CADATA/AVXDATA kit or used standalone when
plugged into RF port for smartphone control. In this mode, data traffic is passed through between
both ports. This will be the most common MODE when used with any Flashlogic Remote Start Kit.
Optional Kit
MODE 3
Virtual Transmitter (MODE 3): In this mode CarLink BT is programed as a keyless entry module.
CarLink BT will control the Flashlogic DOOR LOCK Interface module directly without the use of an
alarm or remote start. This allows smart phone keyless entry control to any factory system. Please
reference www.Flashlogic.com for specific vehicle applications. In this mode, CarLink BT will only
support the keyless entry and convenience features of the application firmware programed to the
Flashlogic Interface. This will not add remote start functionality.
Note: Set Flashlogic interface to iDatalink 2-Way protocol when flashing for Mode 3.
Mode Selection
1. Power up device. Press and hold Programing Button for 1 second. Release Programing Button when LED
flashes rapidly: 150ms on, 150ms off.
2. Press and release Programing Button to advance to ‘MODE1’. The LED will flash 1x repeatedly. Press and
release Programing Button a second time to advance to ‘MODE 2’. The LED will flash 2x repeatedly. Press
and release the Programing Button a third time to advance to ‘MODE 3’. The LED will flash 3x repeatedly.



MODE 1 – Standard Installation
MODE 2 – Flashlogic Remote Start (FLRS) Kit
MODE 3 – Virtual Transmitter
3. Once the desired mode is selected, press and hold the button for 2 Seconds to lock the selection and
enter TEST MODE.
4. With the device in TEST MODE – use the sequences below to test remote start features:




Press Programing Button 1x,
Press Programing Button 2x,
Press Programing Button 3x,
Press Programing Button 4x,
within 2 sec of mode selection, to test LOCK
within 2 sec of mode selection, to test UNLOCK
within 2 sec of mode selection, to test TRUCK RELEASE
within 2 sec of mode selection, to test START/STOP
5. The LED will flash to reflect number of Programing Button presses – i.e. If pressed 2x, it performs unlock,
and the LED flashes 2x ; If pressed 3x, it performs unlock, and the LED flashes 3x, etc.
6. Once you have confirmed testing, press and hold the button for 2 Seconds to lock the selection.
7. Mode Selection and Testing is complete .
Note: If power is disconnected during any of these steps, the system will return to its factory
setting.
Note: Mobile App is not required to test commands above.
System Reset
Press the Programing Button for 3 Seconds after powering up, it will enter System Reset. It will turn on the
LED for 3 seconds then return to all factory defaults.

When the LED turns off, the system will perform Manual Mode Selection again. This allows the
user (or factory) to disconnect power before the 3 second window expires making the device like
new.
FCC Statemen
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursua
nt to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful int
erference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio c
ommunications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined b
y turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your bod
y.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jonathan Frank
Create Date                     : 2016:04:26 10:30:03+08:00
Modify Date                     : 2016:04:26 10:30:04+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2016:04:26 10:30:04+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:1a40c844-add9-4bad-bc8b-0e4fbe033f3a
Instance ID                     : uuid:8cc5e965-2437-4f8f-b6d5-d315710e5358
Subject                         : 16
Format                          : application/pdf
Title                           : Slide 1
Creator                         : Jonathan Frank
Producer                        : Adobe PDF Library 11.0
Source Modified                 : D:20160415063829
Company                         : Microsoft
Created                         : D:20160407
Last Saved                      : D:20160415
Page Layout                     : OneColumn
Page Count                      : 5

EXIF Metadata provided by EXIF.tools