Belkin Ac Anywhere Power Inverter F5C412Uk140W Users Manual P75043uk_F5C412uk_man_uk

AC Anywhere Power Inverter F5C412uk140W p75043uk_f5c412uk

AC Anywhere Power Inverter F5C412uk300W p75043uk_f5c412uk

F5C412uk300W to the manual 4694c686-8ec1-4666-9df8-6fca7d85a9ff

: Belkin Belkin-Ac-Anywhere-Power-Inverter-F5C412Uk140W-Users-Manual-230749 belkin-ac-anywhere-power-inverter-f5c412uk140w-users-manual-230749 belkin pdf

Open the PDF directly: View PDF .
Page Count: 10

User Manual

F5C412uk140W, F5C412uk300W

Power Inverter

(Class II product)

Please read the installation and operations

instructions before using the Power Inverters

AC Anywhere

F5C412uk140W

F5C412uk300W

AC Anywhere – Instructions and Information:

Belkin Components manufactures a line of DC to AC Inverters with 140 and

300-Watt capacities. These Inverters offer advanced technology, dependable

operation and will provide years of reliable service when used in accordance

with our operating instructions.

Belkin’s Inverters convert low voltage, direct (DC) current to 240 volts

alternating (AC) household current. Depending on the model and its rated

capacity, Belkin Inverters draw power either from standard 12-volt automobile

and marine batteries, or from portable, high-power 12-volt sources.

The Belkin inverter can not be used with 24 volts (trucks) battery power.

Important Information:

This manual will provide you with directions for the safe and efficient

operation of your Belkin 140-Watt, or 300-Watt Inverter. Read the manual

carefully before using your new Belkin Inverter and keep the manual on file

for future reference.

Note:

• Your Belkin Inverter is designed to operate from a 12-volt power source

only. Never attempt to connect your Inverter to any other power source

including any AC power sources.

• 240 volts of current can be lethal. Improper use of your Belkin Inverter may

result in property damage, personal injury, or loss of life.

Getting Off to a Good Start:

In order to ensure that the capacity of your Belkin Inverter is sufficient to

meet the required start up load, you must first determine the power

consumption of the equipment or appliance you plan to operate.

Power consumption is rated either in wattage or in amperes. Information

regarding the required “watts” or “amps” is generally printed on most

appliances or equipment. If the power consumption is rated in amps,

multiply the number of amps by 240 volts(AC voltage) to determine the

comparable wattage rating. As a general rule, you can determine the required

start-up load by multiplying the wattage rating by 20.

Don’t Push It:

Although your Belkin Inverter has the capacity to provide power output

equal to approximately two times its rated wattage capacity for a very brief

period, it is designed to operate equipment with start-up load wattage

ratings no higher than its own maximum continuous wattage rating.

Troubleshooting:

Problem:

Equipment has a high start-up surge.

Automotive system

requires ignition to be on.

Battery voltage below 10 volts.

Equipment being operated

draws too much power.

Inverter is too hot

(thermal shutdown mode).

Inverter fuse is blown.

Poor or weak battery condition.

Inadequate power being delivered to

the Inverter or excessive voltage drop.

Solution:

Turn Inverter power switch OFF (O)

and then ON (I) again until the

Inverter powers your device. Repeat as

necessary to get your device running.

Turn ignition key to accessory position.

Recharge or replace battery.

Use a higher capacity Inverter

or do not use this equipment.

Allow Inverter to cool. Check for

adequate ventilation. Reduce the load

on the Inverter to rated continuous

power output.

Replace fuse according to guidelines

in “Don’t Blow a Fuse” section of this

manual. Make sure that the Inverter

is connected to power source with

correct polarity.

Replace battery.

Check condition of cigarette lighter

plug and socket. Clean or replace

as necessary.

Warning:

• Improper use of this inverter can cause personnel injury, property damage,

and or loss of life.

• To avoid potential property damage, do not leave this inverter or any device

operating unattended in vehicle.

• Disconnect power to the inverter when it is not in use.

• Do not use or place this inverter near flammable materials or any locations,

which accumulate flammable fumes.

• If the external flexible cable or cord of this power inverter is damaged, the

manufacturer or his service agent or a similar qualified person shall replace

it in order to avoid a hazard.

• Regularly check that the input and output connections are tight. Loose

connections can generate harmful heat and/or damage the inverter or

power source.

• This product is not recommended for use with inductive loads, such as

florescent lamps, compressors & pumps. Otherwise, permanent damage may

result.

• This is not a toy. Keep away from reach of children.

To connect the Belkin 300-Watt Inverter directly to the 12-volt power source

(battery), follow the steps as outlined below:

1. Push the adapter plug leading from the Inverter firmly into the

Direct-Connect Cable socket.

2. Properly identify the positive (red) and negative (black) terminals on the

12-volt power source and make certain that the terminals are clean and dry.

3. Connect the RED alligator clip to the positive (+) terminal on the power

source, and the BLACK alligator clip to the negative (-) terminal on the

power source.

4. Plug your equipment or appliance into the AC receptacle on the Inverter.

5. Turn the Inverter’s power switch to the ON position.

6. Confirm that the LED power indicator light on the Inverter is glowing

GREEN. This means the Inverter is “ready for action”.

7. Turn on the equipment or appliance.

Specifications

F5C412uk140W F5C412uk300W

Max.Continous Power 140 Watt 300 Watt

Surge efficiency (Peak) 300 Watt 500 Watt

No Load Current Draw <0.1 Amps <0.2 Amps

Waveform Modified Sine Wave

Operating Input Voltage Range 11-15 volts DC

Output Voltage Range AC 240V ±5%

Automatic Input Power Shutdown ≤10.4 Volts - ≥15 Volts

Output Frequency 50 Hz ±3Hz

Fuse (Amperes) 20 A 30 A

Space Fuse (Amperes) 20 A 30 A

Lenght 160 mm 160 mm

Width 90 mm 90 mm

Height 65 mm 65 mm

Weight 680 g 680 g

Class II product yes yes

Polarity negative (-) negative (-)

to ground to ground

Low battery alarm 10.4 Volt 10.4 Volt

Low battery shutdown 9.8 Volt 9.8 Volt

Installation:

Power Source Requirements

The power source must provides 12 Volts DC and must be able to supply the

necessary current to operate the load. The power source may be a battery or

a well-regulated 12V DC power supply. As a rough guideline, divide the power

consumption of the load (in watt) by 12 (the input voltage) to obtain the

current (in amperes) the power source must deliver. Example: Load is rated at

120 Watts; the power source must be able to deliver: (220/12) = 18.3 Amps

Making the Connection:

The Belkin 140 and 300-Watt Inverters are designed to connect to your

12-volt battery through the cigarette lighter socket on your dashboard.

To connect and use these Inverters, follow these easy steps:

1. Remove the cigarette lighter and push the adapter plug firmly into the

socket. Make sure both the socket and adapter plug are clean and dry.

2. Plug your appliance or equipment into the AC receptacle on the Inverter.

3. Turn the Inverter rocker switch to the ON (l) position.

4. Confirm that the LED Power Indicator light on the Inverter is glowing

GREEN. This GREEN light indicates that your Inverter is “ready for action.”

5. Turn on your equipment for use.

Don’t Blow a Fuse:

All Belkin Inverters are equipped with a spare fuse in case the original fuse

should blow. Most blown fuses are the result of reverse polarity or a short

circuit within the appliance or equipment being operated. With reasonable

care, it should not be necessary to replace the fuse in your Inverter.

To Replace a Fuse:

Belkin 140-Watt / 300-Watt Inverter

First, remove the power cord from the cigarette lighter socket. You will find

fuse compartment is easily accessed at the back of the unit underneath the

“lift-up” cover. Pull the blown fuse out, and insert the replacement. It is

important to remember that to replace of fuse of the same type and rating as

indicated. Make certain to correct the source of the overload that caused the

blown fuse before turning your Inverter back ON.

1. Open the fuse box cover 2. Replace the

blown fuse with

a new spade

type fuse

The Power Source:

When the engine is off, most batteries will provide an ample power supply

to the Inverter for one to two hours. The actual length of time is a function

of several variables including the age and condition of the battery, and the

power demand being placed on it by the equipment being operated.

If you are using the Inverter while the engine is off, we recommend you

start the engine every hour and let it run for approximately 10 minutes to

recharge the battery. We also recommend that the device plugged into the

Inverter be turned off before turning over the engine.

Although it is not necessary to unplug the Inverter when starting the

engine, the Inverter may momentarily cease operation as the battery voltage

decreases. When the Inverter is not supplying power, it draws very low

amperage from the battery (< 0.1 amps to < 0.2 amps depending on the

model) and may be left connected to the battery for up to 3 hours. However,

we recommend the Inverter always be disconnected when not in use.

Note:

• Inverters will not operate with certain automotive systems unless the

ignition is on. If the Inverter is not generating power, try turning the

ignition to the accessory position.

Automatic Shut-down and Related Safety Features:

The Belkin 140 and 300-Watt Inverter models have a unique LED indicator

warning light system that operates in conjunction with the automatic shut

down feature. This indicator light operates as follows:

RED - Overload/Low Battery

Your Inverter will shut down automatically when any of the following

problems occur:

1. The power input from the battery drops below 10.4 volts.

2. The power output from the battery exceeds 15 volts.

3. The continuous draw of the device exceeds the design

parameters of the Inverter.

Battery Level Indicator

Approximate State-of-charge Open Circuit Battery Voltage

100% 13.7

75% 12.7

50% 11.7

25% 10.7

0% < 10.6

Additional Safety Features:

1. Automatic shutdown when the internal circuit temperature exceeds

standard design parameters for safe operation.

2. Continuous audible alarm:

a. When the input power from the 12-volt power source drops to 11 volts.

b. When the internal circuit temperature exceeds standard design parameters

for safe operation.

In the event of automatic shut-down or continuous alarm, turn the Inverter

rocker switch to the OFF (O) position until the source of the related problem

has been identified and resolved.

Note:

• The Belkin 300W model is equipped with a cooling fan that is only designed

to run continuously while the Inverter is operating. Automatic shutdown

caused by excess circuit temperature occurs when the cooling fan is unable to

maintain the design parameters for safe operation of the Inverter.

To maintain your Inverter in proper working condition, note the following

important safety precautions:

• MOISTURE - Keep the Inverter dry. Do not expose it to moisture.

• HEAT – The ambient air temperature should be between 50ºF and 80ºF,

(approx. 17ºC - 27ºC). Avoid placing the Inverter on or near heat source.

Do not place the Inverter in direct sunlight.

• VENTILATION – In order to disperse the heat generated while the Inverter

is in operation, keep it well ventilated. While in use, maintain several

inches of clearance around the top and sides of the Inverter.

Caution:

Most automobole cigarette lighter circuits use

fuses rated at 10-20 Amps.

Battery Direct-Connect Cables:

For the Belkin 300-Watt Inverter Only – F5C412uk300W

Note:

• If the equipment or appliance you intend to operate requires more than

150 Watts of continuous power, the Belkin 300-Watt Inverter should be

connected directly to the power source using the Battery Direct-Connect

Cables. Failure to do so may result in serious damage to the power cord or

to the cigarette lighter socket wiring in your vehicle.

FOR USE WITH CIGARETTE LIGHTER PLUG:

1. Insert Inverter’s Cigarette Lighter Plug into vehicle’s cigarette lighter

socket.

Note: Make sure Inverter is not ON when starting vehicle. If ON, a voltage

surge from the vehicle could damage the Inverter or device lugged into it.

2. Turn Inverter “ON” (Switch is located at front of unit, next to 220V electri-

cal sockets). If the LED Status Light on Inverter illuminates GREEN, then

the unit is functioning properly. If the LED Status Light on the Inverter

illuminates RED, turn unit off immediately and check all connections.

3. Plug device(s) (rated lower than 150W) into one of the 220V electrical

sockets. Switch appliance(s) ON to begin operation. As long as LED

Status Light on front panel of Inverter is GREEN, the device may

be operated as normal.

WARNING: If more than 150 Watts of AC power are required from the

Inverter, DO NOT connect the Inverter through the vehicle’s cigarette

lighter socket. THIS WILL OVERHEAT THE WIRES AND COULD CAUSE A

FIRE. When using the devices that require a TOTAL of 150 Watts or more,

connect the Inverter directly to the vehicle’s battery terminals using the

provided Battery Clip.

CAUTION:

Applicable only for the : F5C412uk300w

CONNECTION TO 12V BATTERY

USING BATTERY CLIPS

1. Insert the Inverter’s Cigarette Lighter Plug into the socket on the Battery Clip

Connection Cable.

2. Connect the Red (+) Battery Clip to 12V battery’s red (+) terminal. Connect the

Black (-) Battery Clip to the battery’s black (-) terminal.

3. Turn Inverter “ON”. If the LED Status Light on Inverter illuminates GREEN, the

unit is functioning properly. If the LED Status Light

n the Inverter illuminates RED, turn unit off immediately and check

all connections.

4. Plug 220V appliance into one of the Inverter’s 220V AC Electrical Sockets.

Switch appliance ON to begin operation. As long as Inverter’s LED Status Light

remains GREEN, the device may be

operated as normal.

Note: Make sure Inverter is not ON when starting vehicle. If ON, a voltage surge

from the vehicle could damage the Inverter or device plugged into it.

BATTERY

Battery Level

Indicator Lights

On/Off

Switch

Caution:

Always match the

“continuous wattage rating” of your

device with the DC to AC Inverter

capacity for best results.

Child Protection

built into socket

F5C412uk140W

F5C412uk300W

Belkin Ltd.

Express Business Park

Shipton Way

Rushden NN10 6GL, United Kingdom

+44 (0) 1933 35 2000

+44 (0) 1933 31 2000 fax

Belkin B.V.

Boeing Avenue 333

1119 PH Schiphol-Rijk

The Netherlands

+31 (0) 20 654 7300

+31 (0) 20 654 7349 fax

Belkin GmbH

Hanebergstrasse 2

80637 Munich

Germany

+49 (0) 89 143405 0

+49 (0) 89 143405 100 fax

Belkin SAS

130 rue de Silly

92100 Boulogne-Billancourt

France

+33 (0) 1 41 03 14 40

+33 (0) 1 41 31 01 72 fax

Made in China

Designed and Quality

Assured in the U.S.A.

• P75043uk

© 2005 Belkin Corporation.

All rights reser ved. All trade names

are registered trademarks of

respective manufacturers listed.