Belkin F5D623142 Wireless Cable/DSL Gateway Router User Manual 150000020700ER02 fp

Belkin International, Inc. Wireless Cable/DSL Gateway Router 150000020700ER02 fp

Contents

Part 1

User ManualF5D6231-4Wireless Cable/DSLGateway RouterShare your broadband Internetconnection without cables
TABLE OF CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Easy Install Wizard Software System Requirements . . . . . . . . . . . . . 3Knowing your Belkin Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Placement of your Wireless Router . . . . . . . . . . . . . . . . . . . . . . . . . . 8Connecting and Configuring your Cable/DSL Router . . . . . . . . . . . . . . . 9Alternate Setup Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Using the Web-Based Advanced User Interface . . . . . . . . . . . . . . . . . 34Manually Configuring Network Settings . . . . . . . . . . . . . . . . . . . . . . 69Recommended Web Browser Settings . . . . . . . . . . . . . . . . . . . . . . . . 74Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
1INTRODUCTIONThank you for purchasing the Belkin Wireless Cable/DSL Gateway Router (theRouter). In minutes you will be able to share your Internet connection andnetwork your computers. The following is a list of features that make your newRouter an ideal solution for your home or small office network.Key FeaturesEasy Install WizardThe Easy Install Wizard takes the guesswork out of setting up your Router.This automatic software determines your network settings for you and sets upthe Router for connection to your Internet Service Provider (ISP). In a matterof minutes, your Router will be up and running on the Internet.NOTE: Easy Install Wizard software is compatible with Windows 98, Me, 2000,and XP. If you are using another operating system, the Router can be set upusing the Alternative Method described in this manual. Integrated Wireless ConnectivityThe Router has an integrated 802.11b Wi-Fi Access Point that allows you toconnect wireless-equipped computers to the network without wires.Works with Both PCs and Mac® ComputersThe Router supports a variety of networking environments including Mac® OS 8.x, 9.x, X v10.x, AppleTalk®, Linux®, Windows® 95, 98, Me, NT®,2000, and XP, and others. All that is needed is an Internet browser and anetwork adapter that supports TCP/IP (the standard language of the Internet). Front-Panel Connected LED DisplayLighted LEDs on the front of the Router indicate which functions are inoperation. You’ll know at-a-glance whether your Router is connected to theInternet. This feature eliminates the need for advanced software and status-monitoring procedures.Vertical or Horizontal Desktop ApplicationYour Router can stand vertically on the desktop to save space, or lay downflat on a shelf or under your modem. The included vertical mounting base letsyou decide how to position the Router.Web-Based Advanced User InterfaceYou can set up the Router’s advanced functions easily through your webbrowser, without having to install additional software onto the computer.There are no disks to install or keep track of and, best of all, you can makechanges and perform setup functions from any computer on the networkquickly and easily.
INTRODUCTION2NAT IP Address SharingYour Router employs Network Address Translation (NAT) to share the single IPaddress assigned to you by your Internet Service Provider while saving thecost of adding additional IP addresses to your Internet service account.SPI FirewallYour Router is equipped with a firewall that will protect your network from awide array of common hacker attacks including IP Spoofing, Land Attack, Pingof Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack,TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIPdefect, and fragment flooding.Integrated 10/100 4-Port SwitchThe Router has a built-in, 4-port network switch to allow your wiredcomputers to share printers, data and MP3 files, digital photos, and muchmore. The switch features automatic detection so it will adjust to the speedof connected devices. The switch will transfer data between computers andthe Internet simultaneously without interrupting or consuming resources.Universal Plug-and-Play (UPnP) CompatibilityUPnP (Universal Plug-and-Play) is a technology that offers seamless operationof voice messaging, video messaging, games, and other applications that areUPnP-compliant.Support for VPN Pass-ThroughIf you connect to your office network from home using a VPN connection,your Router will allow your VPN-equipped computer to pass through theRouter and to your office network.Built-In Dynamic Host Configuration Protocol (DHCP) on-board makes forthe easiest possible connection of a network. The DHCP server will assign IPaddresses to each computer automatically so there is no need for acomplicated networking setup.MAC Address FilteringFor added security, you can set up a list of MAC addresses (unique clientidentifiers) that are allowed access to your network. Every computer has itsown MAC address. Simply enter these MAC addresses into a list using the web-based user interface and you can control access to your network.Applications and Advantages• Economically connect multiple computers to a single Internet connection• SOHO (Small Office/Home Office) networking needsProvides the easy and quick small network installation SOHO users need.
INTRODUCTION3Package Contents• Belkin Wireless Cable/DSL Gateway Router• Vertical Mounting Base (optional use)• Category 5 Networking Cable• Power Supply• Belkin Easy Install Wizard Software CD• User ManualSystem Requirements• Broadband Internet connection such as a cable or DSL modem with RJ45(Ethernet) connection• At least one computer with an installed network interface adapter• TCP/IP networking protocol installed on each computer• CAT5 networking cable (or better)• Microsoft® Internet Explorer 4.0 or later, or Netscape® 4.0 or laterEasy Install Wizard Software System Requirements• A PC running Windows 98, Me, 2000, or XP• Minimum 64MB RAM• Internet BrowserNOTE: At the time of printing, a version of the Easy Install Wizard was notavailable for Mac OS users. Please check www.networking.belkin.com to see if aMac OS version of the Easy Install Wizard is now available.
KNOWING YOUR BELKIN ROUTER4The Router has been designed to be placed on a desktop vertically orhorizontally, or it may be mounted to a wall. The slim design minimizes thedesktop space required when placed vertically. All of the cables exit from the rearof the Router for better organization and utility. The LED indicators are easilyvisible on the front of the Router to provide you with information about networkactivity and status.1. Power/Ready LEDWhen you apply power to the Router or restart it, a short period of timeelapses while the Router boots up. During this time, the “Power/Ready”LED blinks. When the Router has completely booted up, the Power/ReadyLED becomes a SOLID light, indicating the Router is ready for use.OFF Router is OFFBlinking Green Router is Booting UpSolid Green Router is Ready2. Wireless Network-Ready LEDOFF Wireless Network is OFFSolid Green Wireless Network is Ready3. LAN Port-Status LEDsThese LEDs are labeled 1–4 and correspond to the numbered ports on the rearof the Router. When a computer is properly connected to one of the LAN portson the rear of the Router, the LED will light. GREEN means a 10Base-T deviceis connected, AMBER means a 100Base-Tx device is connected. Wheninformation is being sent over the port, the LED blinks rapidly.OFF No Device is Linked to the PortGreen 10Base-T Device ConnectedOrange 100Base-Tx Device ConnectedBlinking (Orange or Green) Port Activity
KNOWING YOUR BELKIN ROUTER4. WAN Status LEDThis LED lights in GREEN to indicate that your modem is connectedproperly to the Router. It blinks rapidly when information is being sentover the port between the Router and the modem.OFF No WAN LinkSolid Green Good WAN LinkBlinking Green WAN Activity(1) (2) (3) (4)(6) (7) (8) (9)5(5)(10)Rear PanelFront PanelPort NumberLabelingAntenna
KNOWING YOUR BELKIN ROUTER65. Connected LEDThis unique LED shows you when the Router is connected to the Internet.When the light is OFF, the Router is NOT connected to the Internet. Whenthe light is blinking, the Router is attempting to connect to the Internet.When the light is solid GREEN, the Router is connected to the Internet.When using the “Disconnect after x minutes” feature, this LED becomesextremely useful in monitoring the status of your Router’s connection.OFF Router is not Connected to the InternetBlinking Green Router is Attempting to Connect to the InternetSolid Green Router is Connected to the Internet6. Reset ButtonThe “Reset” button is used in rare cases when the Router may functionimproperly. Resetting the Router will restore the Router’s normaloperation while maintaining the programmed settings. You can alsorestore the factory default settings by using the Reset button. Use therestore option in instances where you may have forgotten your custompassword.a. Using the Reset Button to Reset the RouterPush and release the Reset button. The lights on the Router willmomentarily flash. The Power/Ready light will begin to blink. When thePower/Ready light becomes solid again, the reset is complete.b. Using the Reset Button to Restore the Factory DefaultsPress and hold the Reset button for five seconds then release it. Thelights on the Router will momentarily flash. The Power/Ready light willbegin to blink. When the Power/Ready light becomes solid again, therestore is complete.7. Shared Uplink PortThe shared uplink port is provided for connection to a hub or a switch forexpanding the number of network ports on the Router. If you areconnecting a switch or hub to the Router, connect a straight-through(standard) network cable to this port and to a port on the switch or hub.Note: The uplink port is shared with port 1 of the Router. You cannotconnect a device to the uplink port and to port 1 at the same time.
KNOWING YOUR BELKIN ROUTER78. Internet/WAN PortThis port is for connection to your cable or DSL modem. To ensure properfunctioning, use the cable that was provided with your modem to connectthe modem to this port. NOTE: Using a cable other than the cable supplied with your cable or DSLmodem may cause malfunctioning.9. LAN PortsThe LAN ports are RJ45, 10/100 auto-negotiation ports for standard UTPcategory 5 or 6 Ethernet cable. The ports are labeled 1–4. These portscorrespond to the numbered LEDs on the front of the Router. Note that Port 4 can be made into an uplink port. This means that by pressing theuplink button in, Port 4 will become an uplink port for the addition of aswitch or hub. For more information about the uplink button, see “UplinkButton” below.10. Uplink ButtonThe “Uplink” button is provided for use of Port 4 to connect to a hub or aswitch for expanding the number of network ports on the Router. If youare connecting a switch or hub to the Router, connect a straight-through(standard) network cable to this port and to a port on the switch or hub.Press the Uplink button IN. This will switch Port 4 into an uplink port. NOTE: If you connect a computer to Port 4, and the link LED for Port 4will not turn on, check the Uplink button to make sure that it is in the“Normal” position (OUT).9. Power JackConnect the included 5V DC power supply to this jack.
PLACEMENT OF YOUR WIRELESS ROUTER8Proper placement of your Router is important to ensure the best performance ofyour wireless network. Typically, indoors your Wireless Router can provide acircular coverage area of 250 feet or more. However, different types ofconstruction materials and other obstructions in a building can greatly affect thewireless signal and decrease the range. Whenever possible, your Router should beplaced as close as possible to the center of the area that you want to cover. Inmulti-story homes, place the Router on a floor that is as close to the center ofthe home as possible; this may mean placing the Router on an upper floor. Use care when choosing the location of your Router•Be aware of appliances or large objects such as a refrigerator orwasher/dryer unit that may be on the opposite side of a wall from whereyou decide to place your Router.•Place the Router on top of a desk and away from metal cabinets andcomputer cases.•Do not place objects or components on top of the Router. •Make sure that both antennas are pointing UP at all times.•Metallic-based UV window tint can affect wireless performance. Do not placethe Router next to a tinted window.We realize that in the real world, it may not be possible to place your Router inthe center of your coverage area. In cases where you may experience difficultycovering the entire area you want, try placing the Router as high as possible.Wireless devices work best in a line-of-sight situation where there are noobstacles between the wireless computer and the Router. The Router may also bemounted to a wall with the antennas facing UP. There are other options forexpanding your wireless coverage area. Visit www.networking.belkin.com forsolutions.The wireless signal can be affected by many things including neighboringwireless networks, microwave ovens in operation, and 2.4GHz cordless phones.While these things can affect the network performance, your wireless networktypically will work fine under most conditions where these devices exist.
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER9Verify the contents of your box. You should have the following:• Belkin Cable/DSL Gateway Router• Vertical Mounting Base (optional use)• Category 5 Networking Cable (for connection of the Router to the computer)• Power Supply• Belkin Easy Install Wizard Software CD• User ManualModem RequirementsYour cable or DSL modem must be equipped with an RJ45 Ethernet port. Manymodems have both an RJ45 Ethernet port and a USB connection. If you have amodem with both Ethernet and USB, and are using the USB connection at thistime, you will be instructed to use the RJ45 Ethernet port during the installationprocedure. If your modem has only a USB port, you can request a different typeof modem from your ISP, or you can, in some cases, purchase a modem that hasan RJ45 Ethernet port on it.Easy Install WizardBelkin has provided our Easy Install Wizard software to make installing yourRouter a simple and easy task. You can use it to get your Router up and runningin minutes. The Easy Install Wizard requires that your Windows 98, Me, 2000, orXP computer be connected directly to your cable or DSL modem and that theInternet connection is active and workingat the time of installation. If it is not,you must use the “Alternative Setup Method” section of this manual to configureyour Router. Additionally, if you are using an operating system other thanWindows 98, Me, 2000, or XP, you must set up the Router using the “AlternativeSetup Method” section of this manual.Ethernet USB
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER10IMPORTANT: Run the Easy Install Wizard from the computerthat is directly connected to the cable or DSL modem. DO NOT CONNECT THE ROUTER AT THIS TIME.Step 1: Run the Easy Install Wizard Software1.1 Shut down any programs that are running on your computer at this time.2.2 Make sure you have the following items at the computer that is nowdirectly connected to the cable or DSL modem. DO NOT CONNECT THEROUTER AT THIS TIME.• The Easy Install Wizard CD-ROM• The Router• The Router power supply• Category 5 networking cable• This User Manual1.3 Turn off any firewall or Internet connection sharing software on your computer.1.4 Insert the Easy Install Wizard software CD into your CD–ROM Drive. TheEasy Install Wizard screen will automatically appear on your screen within15 seconds. If it does not, select your CD-ROM drive from “My Computer”and double-click on the file named “Setup” on the CD-ROM.Step 2: Follow the Easy Install Wizard to Complete the Installation
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER112.1 Click on “Set Up the Router” to begin.2.2 Welcome ScreenThe Wizard welcome screen will appear. Make sure you have notconnected the Router at this point. If you have connected your Router,please reconnect your computer directly to the modem. Click “Next” whenyou are ready to move on.2.3 License AgreementPlease read the license agreement in the window. When you are finished,select “I agree” if you want to continue using the software. Click “Idisagree” if you do not want to continue. Click “Next” to move on. CORPORATIONCorporation
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER122.4 Examining SettingsThe Wizard will now examine your computer’s settings and gatherinformation needed to complete the Router’s connection to the Internet.2.5 Multi-NICs ScreenThis screen will appear ONLY if you have more than one network adapterinstalled in your computer. If you have more than one network adapterinstalled in your computer, the Wizard will need to know which adapter isconnected to your modem. Select the network card that is connected toyour modem from the list and click “Next”. If you are not sure whichadapter to choose, select the adapter at the top of the list. If youmistakenly choose the wrong adapter now, you will be able to choose adifferent one later.
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER132.6 PPPoE Connection DetectedIf you have a connection type that requires a user name and a password,the Wizard will ask you to type in your user name and password. If yourconnection type does not require a user name and password, you will notsee this screen.Your user name and password is provided to you by your Internet ServiceProvider. If you have to type in a user name and password to connect tothe Internet, then type that same user name and password in here. Youruser name looks something like “myname@myISP.com” or simply“myname”. The service name is optional and is very rarely required byyour ISP. If you don’t know your service name, leave this blank. When youhave entered your information, click “Next” to move on.Step 3: Connect the Router to your Modem and ComputerThe Wizard will ask you to connect your Router. Follow the steps on the screen,or do the following:3.1 Turn off the power to your modem by unplugging the power supply fromthe modem.3.2 Locate the network cable that is connected between your modem andyour computer and unplug it from your computer, leaving the other endconnected to your modem.
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER143.3 Plug the loose end of the cable you just unplugged into the port on theback of the Router labeled “Internet/WAN”.3.4 Connect the new network cable from the back of the computer to one ofthe ports labeled “1–4”. Note: It does not matter which numbered portyou choose.3.5 Turn on your cable or DSL modem by reconnecting the power supply tothe modem.3.6 Before plugging the power cord into the Router, plug the cord into thewall, then plug the cord into the Router’s power jack.3.7 Verify that your modem is connected to the Router by checking the lightson the front of the Router. The green light labeled “WAN” should be ON ifyour modem is connected correctly to the Router. If it is not, recheckyour connections.3.8 Verify that your computer is connected properly to the Router bychecking the lights labeled “LAN 1,2,3,4”. The light which corresponds tothe numbered port that you connected your computer to should be ON ifyour computer is connected properly.Computer that was originally connected tothe cable or DSL modemTo power adapterCable orDSL modemNew network cable(to computer)Existing network cable(that came with modem)
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER15Step 4: Continue Following the Wizard’s Instructions 4.1 Checking the ConnectionOnce you have completed the connection of your Router, the Wizard willcheck the connection to the Router. If the Router is not detected, usethe “Troubleshooting” button or refer to the “Troubleshooting” section ofthis guide to obtain help about how to correct the problem. If the Wizardis able to communicate with the Router, the Wizard will move on to thenext step.4.2 Configuring the RouterThe Wizard will now transfer all of the configuration information to theRouter. This will take approximately one minute.
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER164.3 When the transfer is complete, the Wizard will tell you that it is done andmay reboot (restart) the Router.4.4 When configuration is complete, the Wizard will tell you “Router SetupComplete” and it will move to the next step.4.5 Checking InternetThe Wizard will now check for an Internet connection. This can take a fewminutes. The Wizard may not detect a connection right away. If not, itwill retry a number of times. The “Connected” light on the front panel ofthe Router will flash during this time. Please be patient through thisprocess. If at the end of this process the Wizard cannot connect to the
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER17Internet, use the Troubleshooting button or refer to the Troubleshootingsection of this guide to obtain help about how to correct the problem.4.6 FinishedWhen the Internet connection is complete, the Wizard will tell you thatyou are finished. The “Connected” LED on the front of the Router will besolid GREEN, indicating that the Router is now connected to the Internet. Your Router is now connected to the Internet. Now you can begin surfingthe Internet by opening your browser and going to your favorite web page.Congratulations! You have finished installing your new Belkin Router. Youare ready to set up the other computers in your home. You can also addcomputers to your Router any time you want. Simply follow step 5 to learnhow to add more computers.
CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER18Step 5: Adding Other Computers to your Network Using the EasyInstall WizardIf you have other computers in your home that are already equipped with awired or wireless network adapter, you can use the Easy Install Wizard to set upthose computers to connect to your Router. If you are adding a Belkin wired orwireless network adapter to your other computers, install the adapter per theinstructions for the adapter. When the installation of the adapter is finished,your computer will be set up to connect to the Router. You do not need to usethe Easy Install Wizard to set up the computer.For Computers Already Equipped with a Wired or Wireless Network Adapter5.1 For wired computers, connect an Ethernet cable between the computeryou want to add to the network and the Router. For wireless-equippedcomputers, make sure your wireless adapter is installed and working. Setyour wireless adapter to connect to a wireless network SSID named“WLAN” or “ANY”. In many cases you will find that you do not have tomake any changes. Refer to the documentation of your wireless networkadapter for information on making this change. Go to the next step.5.2 Insert the CD into your CD-ROM drive. The Easy Installation Wizard screenwill automatically pop-up on your screen within 15 seconds. If it doesnot, select your CD-ROM drive and double-click on the file named “Setup”on the CD-ROM.5.3 Click “Add computers” .
5.4 The Wizard will make the changes needed to add your computer to thenetwork. When finished, it will prompt to reboot your computer. Click “Yes”.5.5 When your computer reboots, your computer will be connected to thenetwork. To begin surfing the Internet, open your browser and go to yourfavorite web page.You are finished adding the computer to the network. To add more computers,repeat this process on each computer you wish to add.CONNECTING AND CONFIGURING YOUR CABLE/DSL ROUTER19
ALTERNATE SETUP METHOD20The Advanced User Interface is a web-based tool that you can use to set up theRouter if you don’t want to use the Easy Install Wizard. You can also use it tomanage advanced functions of the Router. From the Advanced User Interface, youcan perform the following tasks:•View the Router’s current settings and status.•Configure the Router to connect to your ISP with the settings that theyprovided you change the current network settings such as the Internal IPaddress, the IP address pool, DHCP settings and more.•Set the Router’s firewall to work with specific applications (portforwarding).•Set up security features such as client restrictions and MAC addressfiltering.•Enable the DMZ feature for a single computer on your network.•Change the Router’s internal password.•Enable/Disable UPnP (Universal Plug-and-Play).•Reset the Router.•Back up your configuration settings.•Reset the Router’s default settings.•Update the Router’s firmware.Alternative Method Step 1: Connecting your Gateway/Router1.1 Turn off the power to your modem by unplugging the power supply fromthe modem.1.2 Locate the network cable that is connected between your modem andyour computer and unplug it from your computer, leaving the other endconnected to your modem.1.3 Plug the loose end of the cable you just unplugged into the port on theback of the Router labeled “Internet/WAN”.1.4 Connect a new network cable (not included) from the back of thecomputer to one of the ports labeled “1–4”. Note: It does not matterwhich numbered port you choose.1.5 Turn your cable or DSL modem on by reconnecting the power supply tothe modem.
ALTERNATE SETUP METHOD211.6 Before plugging the power cord into the Router, plug the cord into thewall, then plug the cord into the Router’s power jack.1.7 Verify that your modem is connected to the Router by checking the lightson the front of the Router. The green light labeled “WAN” should be ON ifyour modem is connected correctly to the Router. If it is not, recheckyour connections.1.8 Verify that your computer is connected properly to the Router bychecking the lights labeled “LAN 1,2,3,4”. The light which corresponds tothe numbered port connected to your computer should be ON, if yourcomputer is connected properly. If it is not, recheck your connections.Alternative Method Step 2: Set your Computer’s Network Settings toWork with a DHCP ServerSee the section in this manual called “Manually Configuring Network Settings”for directions.Mac or PC computer that was originallyconnected to the cable or DSL modemTo power adapterCable orDSL modemSupplied Ethernetcable (to computer)Existing network cable(that came with modem)
ALTERNATE SETUP METHOD22Alternative Method Step 3: Configuring the Router Using the Web-Based Advanced User InterfaceUsing your Internet browser, you can access the Router’s Web-Based AdvancedUser Interface. In your browser, type “192.168.2.1” (do not type in anything elsesuch as “http://” or “www”). Then press the “Enter” key.Logging into the RouterYou will see the Router’s home page in your browser window. The home page isvisible to any user who wants to see it. To make any changes to the Router’ssettings, you have to log in. Clicking the “Login” button or clicking on any oneof the links on the home page will take you to the login screen. The Router shipswith no password entered. In the login screen, leave the password blank andclick the “Submit” button to log in.Logging out of the RouterOne computer at a time can log in to the Router for the purposes of makingchanges to the settings of the Router. Once a user has logged in to makechanges, there are two ways that the computer can be logged out. Clicking the“Logout” button will log the computer out. The second method is automatic. Thelogin will time out after a specified period of time. The default login time out is10 minutes. This can be changed from 1 to 99 minutes. For more information,see the section in this manual titled “Changing the Login Timeout Setting”.
ALTERNATE SETUP METHOD23Understanding the Web-Based Advanced User InterfaceThe home page is the first page you will see when you access the Advanced UserInterface (UI). The home page shows you a quick view of the Router’s status andsettings. All advanced setup pages can be reached from this page.1. Quick-Navigation LinksYou can go directly to any of the Router’s advanced UI pages by clickingdirectly on these links. The links are divided into logical categories andgrouped by tabs to make finding a particular setting easier to find.Clicking on the purple header of each tab will show you a shortdescription of the tab’s function. 2. Home ButtonThe home button is available in every page of the UI. Pressing thisbutton will take you back to the home page.3. Internet Status IndicatorThis indicator is visible in all pages of the Router, indicating theconnection status of the Router. When the indicator says “connection OK”in GREEN, the Router is connected to the Internet. When the Router isnot connected to the Internet, the indicator will read “no connection” in(1)(2) (3)(4)(5)(6)(7)(8)(9)(10)
ALTERNATE SETUP METHOD24RED. The indicator is automatically updated when you make changes tothe settings of the Router.4. Login/Logout ButtonThis button enables you to log in and out of the Router with the press ofone button. When you are logged into the Router, this button will changeto read “Logout”. Logging into the Router will take you to a separatelogin page where you will need to enter a password. When you are loggedin to the Router, you can make changes to the settings. When you arefinished making changes, you can log out of the Router by clicking the“Logout” button. For more information about logging into the Router, seethe section called “Logging into the Router”.5. Help ButtonThe “Help” button gives you access to the Router’s help pages. Help isalso available on many pages by clicking “more info” next to certainsections of each page.6. LAN SettingsShows you the settings of the Local Area Network (LAN) side of theRouter. Changes can be made to the settings by clicking on any one ofthe links (IP Address, Subnet Mask, DHCP Server) or by clicking the “LAN”Quick Navigation link on the left side of the screen.7. FeaturesShows the status of the Router’s NAT, firewall, and wireless features.Changes can be made to the settings by clicking on any one of the linksor by clicking the “Quick Navigation” links on the left side of the screen.8. Internet SettingsShows the settings of the Internet/WAN side of the Router that connectsto the Internet. Changes to any of these settings can be made by clickingon the links or by clicking on the “Internet/WAN” Quick Navigation linkon the left side of the screen.9. Version InfoShows the firmware version, boot-code version, hardware version, andserial number of the Router.10. Page NameThe page you are on can be identified by this name. This manual willsometimes refer to pages by name. For instance “LAN > LAN Settings”refers to the “LAN Settings” page.
ALTERNATE SETUP METHOD25Alternative Method Step 4: Configuring your Router for Connection to your ISPThe “Internet/WAN” tab is where you will set up your Router to connect to yourInternet Service Provider. The Router is capable of connecting to virtually anyInternet Service Provider’s system provided you have correctly configured theRouter’s settings for your ISP’s connection type. Your ISP connection settings areprovided to you by your ISP. To configure the Router with the settings that yourISP gave you, click “Connection Type” (A) on the left side of the screen. Selectthe connection type you use. If your ISP gave you DNS settings, clicking “DNS”(B) allows you to enter DNS address entries for ISPs that require specificsettings. Clicking “MAC address” (C) will let you clone your computer’s MACaddress or type in a specific WAN MAC address, if required by your ISP. When youhave finished making settings, the “Internet Status” indicator will read“connection OK” if your Router is set up properly.(A)(B)(C)
ALTERNATE SETUP METHOD26Setting your Connection TypeFrom the connection type page, you can select the type of connection you use.Select the type of connection you use by clicking the radio button (1) next toyour connection type and then clicking “Next” (2). Setting your ISP Connection Type to Dynamic IPA dynamic connection type is the most common connection type found withcable modems. Setting the connection type to “dynamic” in many cases isenough to complete the connection to your ISP. Some dynamic connection typesmay require a host name. You can enter your host name in the space provided ifyou were assigned one. Your host name is assigned by your ISP. Some dynamicconnections may require that you clone the MAC address of the PC that wasoriginally connected to the modem. (2)(1)(1)(2)(3)
ALTERNATE SETUP METHOD271. Host NameThis space is provided to enter a host name that needs to be visible to yourISP. Enter your host name here and click “Apply Changes” (3). If your ISPdid not assign you a host name, or you are not sure, leave this blank.2. Change WAN MAC AddressIf your ISP requires a specific MAC address to connect to the service, youcan enter a specific MAC address or clone the current computer’s MACaddress through this link.Setting your ISP Connection Type to Static IPA static IP address connection type is less common than other connection types.If your ISP uses static IP addressing, you will need your IP address, subnet mask,and ISP gateway address. This information is available from your ISP or on thepaperwork that your ISP left with you. Type in your information, then click“Apply Changes” (5). After you apply the changes, the Internet Status indicatorwill read “connection OK” if your Router is set up properly.1. IP AddressProvided by your ISP. Enter your IP address here.2. Subnet MaskProvided by your ISP. Enter your subnet mask here.3. ISP Gateway AddressProvided by your ISP. Enter the ISP gateway address here.4. My ISP Provides More Than one Static IP AddressIf your ISP assigns you more than one static IP address, your Router is(1)(2)(3)(4)(5)
ALTERNATE SETUP METHOD28capable of handling up to five static WAN IP addresses. Select “My ISP provides more than one static IP address” and enter youradditional addresses.Setting your ISP Connection Type to Point-to-Point Protocol over Ethernet (PPPoE)Most DSL providers use PPPoE as the connection type. If you use a DSL modemto connect to the Internet, your ISP may use PPPoE to log you into the service.If you have an Internet connection in your home or small office that doesn’trequire a modem, you may also use PPPoE.Your connection type is PPPoE if: 1. Your ISP gave you a user name and password that is required to connectto the Internet;2. Your ISP gave you software such as WinPOET, Enternet300 that you use toconnect to the Internet; or,3. You must double-click on a desktop icon other than your browser to geton the Internet.To set the Router to use PPPoE, type in your user name and password in thespaces provided. If you do not have a service name or do not know it, leave the“Service Name” field blank. After you have typed in your information, click“Apply Changes” (6). After you apply the changes, the Internet Status indicatorwill read “connection OK” if your Router is set up properly. (1)(2)(3)(4)(5)(6)
ALTERNATE SETUP METHOD291. User NameThis space is provided to type in your user name that was assigned byyour ISP.2. PasswordType in your password and retype it into the “Retype Password” box toconfirm it.3. Service NameA service name is rarely required by an ISP. If you are not sure if your ISPrequires a service name, leave this blank.4. MTUThe MTU setting should never be changed unless your ISP gives you aspecific MTU setting. Making changes to the MTU setting can causeproblems with your Internet connection including disconnection from theInternet, slow Internet access, and problems with Internet applicationsworking properly.5. Disconnect after X….The “Disconnect” feature is used to automatically disconnect the Routerfrom your ISP when there is no activity for a specified period of time. Forinstance, placing a check mark next to this option and entering “5” intothe minute field will cause the Router to disconnect from the Internetafter five minutes of no Internet activity. This option should be used ifyou pay for your Internet service by the minute.Setting your ISP Connection Type to Point-to-Point Tunneling Protocol (PPTP)[European Countries Only]. Some ISPs require a connection using PPTP protocol,a type of connection most common in European countries. This sets up a directconnection to the ISP’s system. Type in the information provided by your ISP inthe space provided. When you have finished, click “Apply Changes”. After youapply the changes, the Internet Status indicator will read “connection OK” ifyour Router is set up properly.
ALTERNATE SETUP METHOD301. PPTP AccountProvided by your ISP. Enter your PPTP account name here.2. PPTP PasswordType in your password and retype it into the “Retype Password” box toconfirm it.3. Host NameProvided by your ISP. Enter your host name here.4. Service IP AddressProvided by your ISP. Enter your service IP address here.5. My IP AddressProvided by your ISP. Enter the IP address here.6. My Subnet MaskProvided by your ISP. Enter the IP address here.7. Connection ID (optional)Provided by your ISP. If your ISP did not give you a connection ID, leavethis blank.(1)(2)(3)(4)(5)(6)(7)(8)
ALTERNATE SETUP METHOD318. Disconnect after X….The Disconnect feature is used to automatically disconnect the Router fromyour ISP when there is no activity for a specified period of time. Forinstance, placing a check mark next to this option and entering “5” into theminute field will cause the router to disconnect from the Internet after fiveminutes of no Internet activity. This option should be used if you pay foryour Internet service by the minute.Setting your Connection Type if you are a Telstra Big Pond User[Australia Only] Your user name and password are provided to you by Telstra BigPond. Enter this information below. Choosing your state from the drop-downmenu (6) will automatically fill in your login server IP address. If your loginserver address is different than one provided here, you may manually enter thelogin server IP address by placing a check in the box next to “Manually EnterServer IP Address” (4) and type in the address next to “Login Server” (5). Whenyou have entered all of your information, click “Apply Changes” (7). After youapply the changes, the Internet Status indicator will read “connection OK” ifyour Router is set up properly.1. Select your StateSelect your state from the drop-down menu (6). The “Login Server” boxwill automatically be filled in with an IP address. If for some reason thisaddress does not match the address that Telstra has given you, you canmanually enter the login server address. See “Manually Enter Server IPAddress” (4).(1)(2)(3)(4)(5)(6)(7)
ALTERNATE SETUP METHOD322. User NameProvided by your ISP. Type in your user name here.3. PasswordType in your password and retype it into the “Retype Password” box toconfirm it.4. Manually Enter Server IP AddressIf your login server IP address is not available in the “Select Your State”drop-down menu (6), you may manually enter the login server IP addressby placing a check in the box next to “Manually Enter Server IP Address”and type in the address next to “Login Server” (5).Setting Custom Domain Name Server (DNS) SettingsA “Domain Name Server” is a server located on the Internet that translatesUniversal Resource Links (URLs) like “www.belkin.com” to IP addresses. ManyISPs do not require you to enter this information into the Router. The “Automaticfrom ISP” box (1) should be checked if your ISP did not give you a specific DNSaddress. If you are using a static IP connection type, then you may need toenter a specific DNS address and secondary DNS address for your connection towork properly. If your connection type is dynamic or PPPoE, it is likely that youdo not have to enter a DNS address. Leave the “Automatic from ISP” boxchecked. To enter the DNS address settings, uncheck the “Automatic from ISP”box and enter your DNS entries in the spaces provided. Click “Apply Changes” (2)to save the settings.(1)(2)
ALTERNATE SETUP METHOD33Configuring your WAN Media Access Controller (MAC) AddressAll network components including cards, adapters, and routers, have a unique“serial number” called a MAC address. Your ISP may record the MAC address ofyour computer’s adapter and only let that particular computer connect to theInternet service. When you install the Router, its own MAC address will be “seen”by the ISP and may cause the connection not to work. Belkin has provided theability to clone (copy) the MAC address of the computer into the Router. ThisMAC address, in turn, will be seen by the ISP’s system as the original MACaddress and will allow the connection to work. If you are not sure whether yourISP needs to see the original MAC address, simply clone the MAC address of thecomputer that was originally connected to the modem. Cloning the address willnot cause any problems with your network. Cloning your MAC AddressTo clone your MAC address, make sure that you are using the computer that wasORIGINALLY CONNECTED to your modem before the Router was installed. Click the“Clone” button (1). Click “Apply Changes” (2). Your MAC address is now clonedto the Router.Entering a Specific MAC AddressIn certain circumstances you may need a specific WAN MAC address. You canmanually enter one in the “MAC Address” page. Type in a MAC address in thespaces provided and click “Apply Changes” to save the changes. The Router’sWAN MAC address will now be changed to the MAC address you specified(1)(2)
USING THE WEB-BASED ADVANCED USER INTERFACE34Using the Web-Based Advanced User InterfaceUsing your Internet browser, you can access the Router’s Web-Based AdvancedUser Interface. In your browser, type “192.168.2.1” (do not type in anything elsesuch as “http://” or “www”) then press the “Enter” key.You will see the Router’s home page in your browser window.Viewing the LAN SettingsClicking on the header of the LAN tab (A) will take you to the LAN tab’s headerpage. A quick description of the functions can be found here. To view thesettings or make changes to any of the LAN settings, click on “LAN Settings” (B)or to view the list of connected computers, click on “DHCP client list” (C).(B)(C)(A)
USING THE WEB-BASED ADVANCED USER INTERFACE35Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed andchanged here.1. IP Address The “IP address” is the internal IP address of the Router. The default IPaddress is “192.168.2.1”. To access the advanced setup interface, typethis IP address into the address bar of your browser. This address can bechanged if needed. To change the IP address, type in the new IP addressand click “Apply Changes”. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:192.168.x.x (where x is anything between 0 and 255)10.x.x.x (where x is anything between 0 and 255)2. Subnet Mask There is no need to change the subnet mask. This is a unique, advancedfeature of your Belkin Router. It is possible to change the subnet mask ifnecessary, however, do NOT make changes to the subnet mask unless youhave a specific reason to do so. The default setting is “255.255.255.0”.(1)(2)(3)(4)(5)(6)
USING THE WEB-BASED ADVANCED USER INTERFACE363. DHCP Server The DHCP server function makes setting up a network very easy byassigning IP addresses to each computer on the network automatically.The default setting is “On”. The DHCP server can be turned OFF ifnecessary, however, in order to do so you must manually set a static IPaddress for each computer on your network. To turn off the DHCP server,select “Off” and click “Apply Changes”.4. IP Pool The range of IP addresses set aside for dynamic assignment to thecomputers on your network. The default is 2–100 (99 computers). If youwant to change this number, you can do so by entering a new startingand ending IP address and clicking on “Apply Changes”. The DHCP servercan assign 100 IP addresses automatically. This means that you cannotspecify an IP address pool larger than 100 computers. For example,starting at 50 means you have to end at 150 or lower so as not to exceedthe 100-client limit. The starting IP address must be lower in numberthan the ending IP address.5. Lease TimeThe length of time the DHCP server will reserve the IP address for eachcomputer. We recommend that you leave the lease time set to “Forever”.The default setting is “Forever”, meaning that any time a computer isassigned an IP address by the DHCP server, the IP address will not changefor that particular computer. Setting lease times for shorter intervals suchas one day or one hour frees IP addresses after the specified period oftime. This also means that a particular computer’s IP address may changeover time. If you have set any of the other advanced features of theRouter such as DMZ or client IP filters, these are dependent on the IPaddress. For this reason, you will not want the IP address to change. 6. Local Domain Name The default setting is “Belkin”. You can set a local domain name (networkname) for your network. There is no need to change this setting unlessyou have a specific advanced need to do so. You can name the networkanything you want such as “MY NETWORK”.
USING THE WEB-BASED ADVANCED USER INTERFACE37Viewing the DHCP Client List PageYou can view a list of the computers (known as clients), which are connected toyour network. You are able to view the IP address (1) of the computer, the hostname (2) (if the computer has been assigned one), and the MAC address (3) ofthe computer’s network interface card (NIC). Pressing the “Refresh” (4) buttonwill update the list. If there have been any changes, the list will be updated.(1)(2)(3)(4)
USING THE WEB-BASED ADVANCED USER INTERFACE38Configuring the Wireless Network SettingsThe Wireless tab lets you make changes to the wireless network settings. Fromthis tab you can make changes to the wireless network name (SSID), operatingchannel, encryption security settings, and configure the Router to be used as anaccess point.
USING THE WEB-BASED ADVANCED USER INTERFACE39Changing the Wireless Network Name (SSID)To identify your wireless network, a name called the SSID (Service Set Identifier)is used. The default SSID of the Router is “WLAN”. You can change this toanything you want to or you can leave it unchanged. If there are other wirelessnetworks operating in your area, you will want to make sure that your SSID isunique (does not match that of another wireless network in the area). To changethe SSID, type in the SSID that you want to use and click “Apply Changes”. Thechange is immediate. If you make a change to the SSID, your wireless-equippedcomputers may also need to be reconfigured to connect to your new networkname. Refer to the documentation of your wireless network adapter forinformation on making this change.
USING THE WEB-BASED ADVANCED USER INTERFACE40Changing the Wireless ChannelThere are a number of operating channels you can choose from. In the UnitedStates, there are 11 channels. In the United Kingdom and most of Europe, thereare 13 channels. In a small number of other countries, there are other channelrequirements. Your Router is configured to operate on the proper channels forthe country you reside in. The default channel is 11. The channel can bechanged if needed. If there are other wireless networks operating in your area,your network should be set to operate on a channel that is different than theother wireless networks. For best performance, use a channel that is at least fivechannels away from the other wireless network. For instance, if another networkis operating on channel 11, then set your network to channel 6 or below. Tochange the channel, select the channel from the drop-down list. Click “ApplyChanges”. The change is immediate.

Navigation menu