Belkin F5D7011A Wireless PCMCIA Card User Manual P74488 F5D7011 man indd

Belkin International, Inc. Wireless PCMCIA Card P74488 F5D7011 man indd

Contents

Users Manual Part 2 Revised

313112345678910sectionUsing the Belkin Wireless LAN UtilityFinding Available Networks in your AreaClick on the “Site Monitor” tab.Clicking on the “Site Monitor” tab will display a list of all available wireless routers or access points in your area.(a) Network Name (SSID)The network name of the wireless router or access point.(b) ChannelThe current operating channel of the wireless router or access point.(c) Signal StrengthThe signal strength of the related wireless router or access point.(d) WEP (Encryption)Will display “Off” when encryption is disabled, “64-bit” when 64-bit encryption is enabled, and “128-bit” when 128-bit encryption is enabled.(e) Ad-Hoc Networks OnlyCheck this box to display available Ad-Hoc networks only. An Ad-Hoc network is a computer-to-computer network.(f) AdvancedDisplays additional information about the selected network.(g) FreezeTakes a “snapshot” of the signal strength at the time of the site survey. Click again to unfreeze.(a)(b) (c)(d)(e) (f)(g)
33323332Using the Belkin Wireless LAN UtilityPerforming Diagnostic Tests on your ConnectionClick on the “Diagnostics” tab.This page allows you to perform several diagnostic tests that are available for your Belkin High-Speed Mode Wireless G Notebook Network Card.Control RegistersThis test verifies the read and write capabilities of the network controller registers by writing various values to the registers and verifying the result. The device driver uses these registers to perform network functions such as sending and receive information. If the test fails, the network adapter may not work properly.SPROM Format VersionThis test verifies the content of the SPROM by reading a portion of the SPROM and computing the checksum. The test fails if the computed checksum is different than the checksum stored in the SPROM.Memory TestsThis tests verifies that the network controller internal memory is functioning properly. The test writes patterned values to the memory and reading back the results. The test fails if an erroneous value is read back. The network controller will not function without its internal memory.
333312345678910sectionUsing the Belkin Wireless LAN UtilityInterrupt TestThis test verifies that the NDIS driver is able to receive interrupts from the network controller.Loopback TestThis test verifies that the NDIS driver is able to send packets and receive packets from the network controller.LED TestThis test verifies that your 802.11 wireless networking hardware is functioning correctly.
35343534I can’t connect to the Internet wirelesslyIf you are unable to connect to the Internet from a wireless computer, please check the following items:1. Look at the lights on your Wireless Router. If you’re using a Belkin Wireless Router, the lights should be as follows:• The “Power” light should be on.• The “Connected” light should be on, and not blinking.• The “WAN” light should be either on or blinking.If your Belkin Wireless Router’s lights have the above characteristics, go to number 2. below.If this is NOT the case, make sure:• The Router power cord is plugged in• All cables are connected between the router and the modem• All the modem’s LEDs are functioning correctly. If not, see your modem’s user manual.• Reboot the Router• Reboot the ModemIf you continue to have issues, please contact Belkin Technical Support.If you are not using a Belkin Wireless Router, consult that router manufacturer’s user guide.2. Open your wireless utility software by clicking on the icon in the system tray at the bottom right-hand corner of the screen. If you’re using a Belkin wireless card, the tray icon should look like this (the icon may be red or green):Troubleshooting
3535section123456789103. The exact window that opens will vary depending on the model of wireless card you have; however, any of the utilities should have a list of “Available Networks”. Available networks are wireless networks you can connect to.If you are using a Belkin 802.11g (125HSM) router, or Belkin 802.11g (54g) router, “Belkin54g” is the default name.If you are using a Belkin 802.11b router, the default name should be “WLAN”. If using a non-Belkin router, please consult your router manufacturers user manual for the default name.The name of your wireless network appears in “Available Networks”If the correct network name is listed in the “Available Networks” list, please follow the steps below to connect wirelessly:1. Click on the correct network name in the “Available Networks” list.2. If the network has security (encryption) enabled, you will need to enter the network key. Click “Connect”. For more information regarding security, see the page entitled: “Securing your Wi-Fi Network” on pg. 16 of the user manual.3. Within a few seconds, the tray icon in the lower right-hand corner of your screen should turn green, indicating a successful connection to the network. If you are still unable to access the Internet after connecting to the wireless network, please contact Belkin Technical Support. Troubleshooting
37363736TroubleshootingThe name of your wireless network DOES NOT appear in the list of “Available Networks”If the correct network name is not listed, check the SSID settings to see if they match. The SSID is case-sensitive and the spelling on each computer must be exactly the same in order for the Card to connect to the Wireless Router or Access Point. Note: To check the SSID settings or look for an available network, double-click the Signal Indicator icon to bring up the “Wireless Networks” screen. Click “Add” if you do not see the network you are trying to connect to and type in the SSID. For more information about setting up a SSID please reference your router manufacture’s user manual.If issues persist even at close range, please contact Belkin Technical Support. Installation CD-ROM does not start Setup UtilityIf the CD-ROM does not start the Setup Utility automatically, it could be that the computer is running other applications that are interfering with the CD drive.If the Setup Utility screen does not appear within 15-20 seconds, open up your CD-ROM drive by double-clicking on the “My Computer” icon. Next, double-click on the CD-ROM drive that the Installation CD has been placed in to start the installation. Then double-click on the folder named “Files”. Next, double-click on the icon named “setup.exe”.Power LED does not come ON; Card is not workingIf the LED indicators are not ON, the problem may be that the Card is not connected or installed properly. Verify that the Card is plugged firmly into the CardBus slot of your computer. Check to see that the drivers for the Card have been installed. Right click on the “My Computer” icon on your desktop. Choose “Properties” and navigate to the “Device Manager” and see if your CardBus Card is listed without any errors. If an error is indicated contact Belkin Technical Support.
3737section12345678910Link LED is blinking slowly; Cannot connect to a wireless network or the InternetIf your Card appears to be functioning properly, but you cannot connect to a network or you have a red wireless icon at the bottom of your screen, the problem may be that there is a mismatch between the network name (SSID) settings in your wireless network properties. Check the SSID settings to see if they match. The SSID is case-sensitive and the spelling on each computer must be exactly the same in order for the Card to connect to the Wireless Router or Access Point. Note: To check the SSID settings or look for an available network, double-click the Signal Indicator icon to bring up the “Wireless Networks” screen. Click “Add” if you do not see the network you are trying to connect to and type in the SSID. For more information about setting up a SSID please reference your router manufactures user manual. If issues persist even at close range, please contact Belkin Technical Support. Link LED is solid but cannot connect to the Internet If you have a signal but can’t get online or obtain an IP address, the problem may be that there is a mismatch between the Encryption key settings in your computer and Wireless Router or Access Point. Check the WEP key settings to see if they match. The key is case-sensitive and the spelling on each computer and Wireless Router or Access Point must be exactly the same in order for the Adapter to connect to the router. For more information about encryption please see “Securing your Wi-Fi Network” on page 16 of this manual.If issues persist even at close range, please contact please contact Belkin Technical Support. Troubleshooting
39383938TroubleshootingData transfer is sometimes slowWireless Technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. As a result, the typical indoor range of your wireless devices will be between 100 to 200 feet. Note also that connection speed may decrease as you move further from the Wireless Router or Access Point. In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, to five to ten feet from the Wireless Router or Access Point. Please see the section titled “Placement of your Wireless Networking Hardware for Optimal Performance” on page 2 of this manual. If issues persist even at close range, please contact please contact Belkin Technical Support. Signal strength is poorWireless Technology is radio-based, which means connectivity and the throughput performance between devices decreases when the distance between devices increases. Other factors that will cause signal degradation (metal is generally the worst culprit) are obstructions such as walls and metal appliances. As a result, the typical indoor range of your wireless devices will be between 100 to 200 feet. Note also that connection speed may decrease as you move further from the Wireless Router or Access Point. In order to determine if wireless issues are related to range, we suggest temporarily moving the computer, if possible, to five to ten feet from Wireless Router or Access Point.Changing the wireless channel – Depending on local wireless traffic and interference, switching the wireless channel of your network can improve performance and reliability. The default channel the router is shipped with is channel 11, you may choose from several other channels depending on your region; see your router or access point user manual for instructions on how to choose other channels.Limiting the wireless transmit rate – Limiting the wireless transmit rate can help improve the maximum wireless range, and connection stability. Most wireless cards have the ability
3939section12345678910to limit the transmission rate. To change this property, go to the Windows Control Panel, open the Network Connections and double-click on your wireless card’s connection. In the properties dialog, select the configure button on the General tab (Windows 98 users will have to select the wireless card in the list box and then click properties), then choose the advanced tab and select the Rate property. Wireless client cards are usually set to automatically adjust the wireless transmit rate for you, but doing so can cause periodic disconnects when the wireless signal is too weak; as a rule, slower transmission rates are more stable. Experiment with different connection rates until you find the best one for your environment; note that all available transmission rates should be acceptable for browsing the Internet. For more assistance, see your wireless card’s literature.If issues persist even at close range, please contact please contact Belkin Technical Support. Why are there two wireless utilities in my system tray? Which one do we use? There are several features and advantages from using the Belkin wireless utility over the Windows XP Wireless Zero Configuration utility. We offer a site survey, detailed link information and adapter diagnosis, to name a few.It’s essential to know which utility is managing your adapter. We recommend using the Belkin wireless utility.To use the Belkin wireless utility follow the steps below:Step 1 Right-click on the network status icon in the system tray and select View Available Wireless Networks.Step 2 Click on the Advanced button in the lower-left corner of the Available Wireless Networks window.Step 3 From the Advanced tab uncheck “Use Windows to configure my wireless network”. Once the box is unchecked click OK to close the Window.You are now using the Belkin wireless Utility to configure the wireless card. Troubleshooting
41404140TroubleshootingCard does not perform or connection is unstable when computer has a second built-in wireless network card (such as a mini PCI or Intel® Centrino™)This condition occurs if your computer has a built-in wireless card while your Belkin Wireless Card is also active. This happens because Windows must now handle two active wireless connections. You need to disable the built-in wireless card from your computer under “Network Adapters” in the Device Manager.Card does not perform or connection is slow when computer has a built-in wired Ethernet cardThis condition occurs if your computer has an active Ethernet card while your Wireless Adapter is also active. This happens because Windows must now handle two active network connections. You need to disable the Ethernet card from your computer under “Network Adapters” in the Device Manager.
4141section12345678910TroubleshootingWireless Technology 802.11b 802.11g 802.11a Speed 11Mbps 54Mbps 54Mbps FrequencyCommon household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4 GHzCommon household devices such as cordless phones and microwave ovens may interfere with the unlicensed band 2.4 GHz5GHz - uncrowded bandCompatibility Compatible with 802.11gCompatible with 802.11bIncompatible with 802.11b or 802.11gRangeDepends on interference - typically 100–200 ft. indoorsDepends on interference - typically 100–200 ft. indoorsLess interference - range is typically 50-100 feetAdoption Mature – widely adoptedExpected to continue to grow in popularitySlow adoption for consumers - more popular in business environmentsPrice Inexpensive More expensive Most expensiveWhat’s the difference between 802.11b, 802.11g and 802.11a? Currently there are three levels of wireless networking standards, which transmit data at very different maximum speeds. Each is based on the designation 802.11(x), so named by the IEEE, the board that is responsible for certifying networking standards. The most common wireless networking standard, 802.11b, transmits information at 11Mbps; 802.11a and 802.11g work at 54Mbps. See the following chart for more detailed information.Wireless Comparison
43424342TroubleshootingTechnical SupportYou can find technical support information at www.belkin.com or www.belkin.com/networking. If you want to contact technical support by phone, please call: US: 877-736-5771 Europe: 00 800 223 55 460 Australia: 1800 666 040
4343section12345678910Caution: Exposure to Radio Frequency Radiation. The radiated output power of this device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such manner that the potential for human contact normal operation is minimized.End users must follow the specific operating instructions for satisfying RF exposure compliance.Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.FCC StatementDECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITYWe, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product,F5D7011to which this declaration relates,complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Information
44123456section"Belkin declare that F5D7011 is limited in CH1~CH11 by specified firmware controlled in USA."This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.INFORMATION TO USER:The users manual or instruction manual for an intentional or unintentionalradiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE to operate the equipment.IC StatementTo prevent radio interference to the licenced service, this device is intended tobe operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing InformationOperation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
45454544InformationThis equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the distance between the equipment and the receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Modifications The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by Belkin Corporation may void the users authority to operate the equipment.Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital complies with Canadian ICES-003.Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada.Europe-European Union Notice Radio products with the CE 0560 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the 0560 Commission of the European Community. Compliance with this directive implies conformity to the following European Norms (in brackets are the equivalent international standards). • EN 60950 (IEC60950) – Product Safety • EN 300 328 Technical requirement for radio equipment • ETS 300 826 General EMC requirements for radio equipment.To determine the type of transmitter, check the identification label on your Belkin product.
4612345678910sectionProducts with the CE marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (72/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards). • EN 55022 (CISPR 22) – Electromagnetic Interference • EN 55024 (IEC61000-4-2,3,4,5,6,8,11) – Electromagnetic Immunity • EN 61000-3-2 (IEC610000-3-2) – Power Line Harmonics • EN 61000-3-3 (IEC610000) – Power Line Flicker • EN 60950 (IEC60950) – Product SafetyProducts that contain the radio transmitter are labeled with CE 0560 or CE alert marking and may also carry the CE logo.Belkin Corporation Limited Lifetime Product WarrantyBelkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required. This warranty does not apply if the product has been damaged by accident, abuse, misuse, or misapplication; if the product has been modified without the written permission of Belkin; or if any Belkin serial number has been removed or defaced.THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.No Belkin dealer, agent, or employee is authorized to make any modification, extension, or addition to this warranty.BELKIN IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN, OR USED WITH, BELKIN PRODUCTS.Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties, so the above limitations of exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.Information
belkin.com© 2004 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. BROADCOM, 54g, the 54g logo, 125 High Speed Mode, and the 125 High Speed Mode logo are trademarks of Broadcom Corporation in the United States and/or other countries.P74488-AHigh-Speed Mode Wireless G Notebook Network Card Belkin, Ltd.7 Bowen Crescent • West GosfordNSW 2250 • AustraliaTel: +61 (0) 2 4372 8600Fax: +61 (0) 2 4372 8603Belkin Components B.V.Starparc Building • Boeing Avenue 3331119 PH Schiphol-Rijk • The NetherlandsTel: +31 (0) 20 654 7300Fax: +31 (0) 20 654 7349Belkin Tech SupportUS: 877.736.5771 310.898.1100 ext. 2263Europe: 00 800 223 55 460Australia: 1800 666 040Belkin Corporation501 West Walnut StreetCompton • CA • 90220 • USATel: 310.898.1100Fax: 310.898.1111Belkin Components, Ltd.Express Business Park • Shipton Way Rushden • NN10 6GL • United KingdomTel: +44 (0) 1933 35 2000Fax: +44 (0) 1933 31 2000

Navigation menu