Belkin F8Z341 Low Power FM Transmitter for use with iPod or iPhone User Manual

Belkin International, Inc. Low Power FM Transmitter for use with iPod or iPhone Users Manual

Users Manual

Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
® TuneBase for iPhone and iPod
Show icons like cover of P74667
User Manual
Table of Contents
1 Introduction
2 Connecting Your TuneBase Auto
3 Selecting an FM Frequency
Using ClearScan to Select the Best FM Frequency (recommended)
Manually Selecting an FM Frequency
Storing and Selecting a Frequency
4 Using the PRO Setting to Improve Performance
Listening to Mono Recordings
5 Getting the Most Out of Auto
Charging Your iPhone or iPod
Radio Data System (RDS)
Optimizing the Sound Quality of Your Auto
6 Safety Warnings
7 Information
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
Introduction
Your Auto is designed to power, charge, and transmit audio from your iPhone or
iPod to your car stereo. Please review this User Manual carefully so that you can
get the most from your Auto, virtually anywhere you go.
Connecting Your Auto
1. Turn down your stereo’s volume.
2. Connect your Auto to the cigarette lighter or power outlet in your vehicle.
(insert line art # 1 from QIG file)
3. Connect your iPhone or iPod to your Auto. (insert line art# 2 from QIG file)
Note: Your Auto will automatically turn off if there is no audio for approximately
60 seconds for European versions, but it will automatically turn on again when it
detects audio from your iPhone or iPod. You can also press the “m1” or “m2”
button to turn on your Auto.
Selecting an FM Frequency
You can use ClearScan to find a frequency and match it to your stereo, or you
can find a frequency on your stereo and match your Auto to the same frequency.
Using ClearScan to Select the Best FM Frequency (recommended)
Your Auto uses ClearScan technology to constantly scan for the clearest FM
frequency in your area.
1. Press the (Insert ClearScan icon) “ClearScan” button. Your Auto will display
the best frequency. (line art #3 on QIG file)
(Insert Line Art of “Tune To” and Frequency)
2. Tune your stereo to the frequency on your Auto display.
Note: If you immediately press the “ClearScan” button when you turn on your
TuneBase Auto, it may take up to 10 seconds for ClearScan to locate the best
frequency. If your audio signal declines, just press “ClearScan” and the best FM
frequency will instantly display.
Manually Selecting an FM Frequency
If you want to use a specific frequency, you can manually select it on your
TuneBase Auto.
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
1. Tune your stereo to a frequency between stations. The ideal frequency is one
not broadcasting a radio station’s signal.
2. Press the + or - button on your TuneBase Auto to select the same frequency.
(insert line art #1 and #2 under manual frequency on QIG file)
3. To identify the best available frequencies in your area, visit
www.belkin.com/mybestfm.
Storing and Selecting a Frequency
You can store two frequencies using the “m1” and “m2” buttons.
1. To store a frequency, select the desired frequency on your TuneBase Auto
using the + or - buttons. Press and hold the “m1” or “m2” preset button for two
seconds. The “m1” or “m2” icon will flash on the screen when the frequency is
set.
2. To recall a preset frequency, press the “m1” or “m2” preset button. Your
TuneBase Auto will change to the preset frequency.
Using the PRO Setting to Improve Performance
When you connect your iPhone or iPod, your TuneBase Auto will automatically
detect the iPhone or iPod model and adjust the volume. Although the default
volume setting will be ideal for most conditions, you may be able to improve the
audio performance of your TuneBase Auto by using the PRO setting.
Normal – No change to the audio. This setting works well with all types of audio.
PRO 1 – Increases the average volume of the audio. This setting works well with
most types of music.
PRO 2 – Increases the average volume even further. This setting works well with
quieter music, but it may cause distortion with louder music.
PRO (symbol) – Increases the average volume and transmits in mono (instead of
stereo). This setting works well for podcasts and audio books. It can also be used
to improve reception if you are not receiving a clear signal from your TuneBase
Auto.
When you press the “PRO” button, your TuneBase Auto will display the PRO
setting. Pressing the “PRO” button again will change the setting to PRO 1, PRO
2, and PRO (symbol) as follows:
OFF PRO 1 PRO 2 PRO (symbol)
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
Listening to Mono Recordings
Your TuneBase Auto transmits in stereo, but you can also transmit in mono if
needed. We suggest that you switch to mono transmission only if your car stereo
is not receiving a clear signal from the TuneBase Auto or if you are listening to a
mono recording such as an audio book.
To switch to mono transmission, press the “PRO” button until “PRO (symbol)” is
shown on the display. The “PRO” button settings are as follows:
OFF PRO 1 PRO 2 PRO (symbol)
Getting the Most Out of TuneBase Auto
Charging Your iPhone or iPod
Your TuneBase Auto will charge your iPhone or iPod while it is connected to a
power outlet and receiving power. If your iPhone or iPod is not charging, make
sure your TuneBase Auto is correctly connected to the power outlet and that your
iPhone or iPod is securely connected to your TuneBase Auto. The indicator light
on the cigarette lighter adapter should be lit.
Note: Some vehicles do not provide power to the power outlet unless the vehicle
is in ignition mode or the engine is running.
Radio Data System (RDS)
The RDS system standardizes several types of information transmitted, including
time, track, artist information, and station identification. TuneBase Auto supports
RDS and can display artist name followed by song title on your car stereo
display. Information is displayed eight characters at a time. This will repeat on
your stereo display until the transmission ends, or it is replaced by another song.
Refer to your car stereo’s manual to find out if it has the RDS feature.
Optimizing the Sound Quality of your TuneBase Auto
A variety of car radio and antenna configurations are available and you may
optimize the sound quality in your car based on the location of your TuneBase
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
Auto (for example, placing the TuneBase Auto on the center console may yield
better performance than other locations within your vehicle).
Safety Warnings
Do not attempt to connect your TuneBase Auto while driving. Make sure
your TuneBase Auto fits securely and firmly into the power outlet before driving.
Do not attempt to adjust or retrieve an unsecured TuneBase Auto or iPhone
or iPod while driving. Position the TuneBase Auto so that both the TuneBase
Auto and the iPhone or iPod do not interfere with any of the operating controls of
the car.
Do not insert any objects other than the cigarette lighter adapter into the
power outlet without disconnecting the battery of the car first. Failure to
observe this safety warning can result in injury or property damage.
Belkin does not assume any responsibility for personal injury or property damage
incurred due to hazardous driving as a result of interaction with the TuneBase
Auto, the iPhone or iPod, or the vehicle’s power outlet.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
Belkin International, Inc., is not responsible for any interference caused by
unauthorized modifications to this equipment. Such modifications could void the
user’s authority to operate this equipment.
FCC, C-Tick Certifications
Belkin International, Inc., Limited 3-Year Product Warranty
What this warranty covers.
Belkin International, Inc. (“Belkin”) warrants to the original purchaser of this
Belkin product that the product shall be free of defects in design, assembly,
material, or workmanship.
What the period of coverage is.
Belkin warrants the Belkin product for three years.
What will we do to correct problems?
Product Warranty.
Belkin will repair or replace, at its option, any defective product free of charge
(except for shipping charges for the product). Belkin reserves the right to
discontinue any of its products without notice, and disclaims any limited warranty
to repair or replace any such discontinued products. In the event that Belkin is
unable to repair or replace the product (for example, because it has been
discontinued), Belkin will offer either a refund or a credit toward the purchase of
another product from Belkin.com in an amount equal to the purchase price of the
product as evidenced on the original purchase receipt as discounted by its
natural use.
What is not covered by this warranty?
All above warranties are null and void if the Belkin product is not provided to
Belkin for inspection upon Belkin’s request at the sole expense of the purchaser,
or if Belkin determines that the Belkin product has been improperly installed,
altered in any way, or tampered with. The Belkin Product Warranty does not
protect against acts of God such as flood, lightning, earthquake, war, vandalism,
theft, normal-use wear and tear, erosion, depletion, obsolescence, abuse,
damage due to low voltage disturbances (i.e. brownouts or sags), non-authorized
program, or system equipment modification or alteration.
How to get service.
To get service for your Belkin product you must take the following steps:
1. Contact Belkin International, Inc., at 501 W. Walnut St., Compton, CA
90220, Attn: Customer Service, or call (800)-223-5546, within 15 days of
the Occurrence. Be prepared to provide the following information:
a. The part number of the Belkin product.
b. Where you purchased the product.
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
c. When you purchased the product.
d. Copy of original receipt.
2. Your Belkin Customer Service Representative will then instruct you on
how to forward your receipt and Belkin product and how to proceed with
your claim.
Belkin reserves the right to review the damaged Belkin product. All costs of
shipping the Belkin product to Belkin for inspection shall be borne solely by the
purchaser. If Belkin determines, in its sole discretion, that it is impractical to ship
the damaged equipment to Belkin, Belkin may designate, in its sole discretion, an
equipment repair facility to inspect and estimate the cost to repair such
equipment. The cost, if any, of shipping the equipment to and from such repair
facility and of such estimate shall be borne solely by the purchaser. Damaged
equipment must remain available for inspection until the claim is finalized.
Whenever claims are settled, Belkin reserves the right to be subrogated under
any existing insurance policies the purchaser may have.
How state law relates to the warranty.
THIS WARRANTY CONTAINS THE SOLE WARRANTY OF BELKIN. THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR, EXCEPT AS REQUIRED
BY LAW, IMPLIED, INCLUDING THE IMPLIED WARRANTY OR CONDITION
OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, AND SUCH IMPLIED WARRANTIES, IF ANY, ARE LIMITED IN
DURATION TO THE TERM OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so
the above limitations may not apply to you.
IN NO EVENT SHALL BELKIN BE LIABLE FOR INCIDENTAL, SPECIAL,
DIRECT, INDIRECT, CONSEQUENTIAL OR MULTIPLE DAMAGES SUCH AS,
BUT NOT LIMITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE
SALE OR USE OF ANY BELKIN PRODUCT, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
This warranty gives you specific legal rights, and you may also have other rights,
which may vary from state to state. Some states do not allow the exclusion or
limitation of incidental, consequential, or other damages, so the above limitations
may not apply to you.
BELKIN
www.belkin.com
Belkin Tech Support
US: 800-223-5546, ext. 2263
Manual-1 20031_PM01714-C_PM01714tt-
A_F8Z341_TuneBase_Auto_iPod_Mnlr1df_091108 (2)-1.doc
310-898-1100, ext. 2263
UK: 0845 607 77 87
Australia: 1800 235 546
New Zealand: 0800 235 546
Singapore: 65 64857620
Europe: www.belkin.com/support
Belkin International, Inc.
501 West Walnut Street
Los Angeles, CA 90220, USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park, Shipton Way
Rushden, NN10 6GL, United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk, The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
Belkin Ltd.
4 Pioneer Avenue
Tuggerah Business Park
Tuggerah, NSW 2259, Australia
+61 (0) 2 4350 4600
+61 (0) 2 4350 4700 fax
© 2008 Belkin International, Inc. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed. iPod is a trademark of
Apple Inc., registered in the U.S. and other countries. iPhone is a trademark of
Apple Inc.
PM01714-C
PM01714tt-A
F8Z341-XXX
Ok mk 11/10/08

Navigation menu