Bell F20 Speedometer Users Manual
2015-02-02
: Bell Bell-F20-Speedometer-F20-Users-Manual-402165 bell-f20-speedometer-f20-users-manual-402165 bell pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Bell Wireless Speedometer™ Installation Components BATTERY Make sure to write down the Odometer value before changing the battery so you can later re-enter it in the odometer. Install the new battery with the positive (+) pole facing outward (Figure 1). After changing the battery all settings are erased. Clamp the magnet to a spoke on the right side of the front wheel (Figure 2). Make sure that the magnet is facing the outside of the wheel so that the flat side of the magnet passes in front of the sensor. Attach the speedometer sensor to the right fork leg using the two cable ties provided. Make sure the metal side of the sensor is facing the wheel. Do not fully secure the cable ties yet, as the sensor location might require further adjustments (Figure 3). Adjust the sensor and magnet location so that clearance between the two is no greater than 1/5" (5mm) (Figure 4). Magnet should pass by the tip of the sensor. Remove the adhesive tape shield on the back of the bracket and position the bracket on the handlebar of the bicycle. Fasten the O-ring around the top edge of the bracket and wrap around the underside of the handlebar and attach to the bottom edge of the bracket. Insert the computer into the mounting bracket and twist to the right to lock into place. Sensor Computer Unit Computer Battery (3.0V/CR2032) Mounting Bracket Mountain Bike UPPER SCREEN 20" 1596 24" 1888 22" 1759 26" 2045 · Current Speed (SPD) 0–199.9 Km/hr or M/hr 24" 1916 27" 2155 · Calories Burned (CAL) 0–999.9 Calories Burned 26" 2073 28" 2237 · Speed Comparison (+ or -) Km or Mile Selection After setting the Wheel Factor the Km/M selection will appear. Press the Right button to choose kilometer or mile. Press the Left button to confirm. 12 or 24 Hour Format Selection After the Km/M input selection, the clock format screen will appear. Press the Right button to choose between the two formats. Press the Left button to confirm. O-Rings (3) KG or LB Selection After the hour format selection, the Kg/Lb selection will appear. Press the Right button to choose between Kilograms (Kg) or Pounds (Lb). Press the Left button to confirm choice. Magnet Cable Ties (2) Bicycle Bicycle Bicyclefork fork fork Magnet Magnet Magnet Magnet Magnet Magnet 5mm 5mm 5mm Sensor Sensor Sensor Sensor Sensor Sensor Top Top TopView View View · Call 1-800-456-BELL if you have any questions about installation. Now that the speedometer is configured, insert the computer into the bracket and twist to the right to lock in place. To check for proper installation, spin the front wheel. The speed tendency icon in the upper left corner of the screen should be turning as the computer starts recording data (Refer to Troubleshooting in case of problems). 27"/ 700c 2124 Sensor Sensor Sensor · Improper installation of this or any other bike computer can result in an accident. Read instructions carefully. Quickstart Wheel Size Input The flashing number "2124" is the preset value. To determine the correct wheel factor, refer to the table shown. Set the wheel factor by pressing the Right button until the correct setting appears. Press the Left button to lock in the correct digit. Repeat until all four digits are entered. Road Bike oror or Warning! Programming the Computer · Check mounting hardware and transmitter installation before each ride for adjustment and secure fit. · This computer will not fit all bikes. If you cannot get a secure installation per the instruction manual, do not use this computer. Once the weight unit is selected, the computer will ask the user to enter his/her weight. This will allow the computer to accurately estimate the number of calories burned while riding. To enter the correct weight, press the Right button until the correct digit appears. Press the Left button to lock in the correct digit. Repeat until all digits are entered. NOTE: The weight entered should be between 80–499Lb or 35–199Kg. The speedometer is now ready to use. Clock Set the time by pressing and holding the Right button until the hour is flashing. To set, press the Right button until desired setting is displayed. Press the Left button to confirm. Repeat steps for the minute setting. · Speed Tendency LOWER SCREEN · Trip Distance (DST) 0–999.9 Km or M · Trip Timer (TM) 9 hrs 59 min 59 sec · Odometer (ODO) · Average Speed (AVS) · Maximum Speed (MXS) · Clock Current Speed (SPD) Current Speed represents instantaneous speed. It is displayed on the upper screen. The speedometer measures speeds up to 200Km/hr or 125 M/hr. If no keys are touched and no movement sensed from the bicycle for five minutes, the speedometer will go into sleep mode. Press any key to reactivate. Calories Burned (CAL) Calories Burned is displayed on the upper screen. It represents the accumulated number of calories burned while riding. The calorie count on the screen will start over once 999 calories have been burned. Calories Burned can be reset at any time by pressing and holding the Left button when "CAL" is displayed on the screen. Speed Comparison (+ or -) "+" or "-" appears next to the current speed. This function shows the positive or negative acceleration of your Continued On Reverse Side Quickstart (Continued) current speed. If the current speed is higher than the average speed, a "+" is displayed on your screen. If the current speed is lower than the average speed, a "-" is displayed on the screen. Shows only when SPD function is on upper screen. Speed Tendency "Graphic" is the animation of the wheel moving. Trip Distance (DST) Press the Right button until "DST" appears. Trip Distance is displayed on the lower screen. It is activated automatically with the bicycle in motion. Trip Distance can be reset by pressing and holding the Right button for two seconds when "DST" is displayed on the screen. NOTE: Resetting Trip Distance will automatically reset Trip Timer and Average Speed. Trip Timer (TM) Trip Timer is displayed on the lower screen. It is activated automatically with the bicycle in motion: it is on when you ride and off when you stop. To display the timer, press the Right button until "TM" appears. The timer records the total cycling time for each trip. Trip Timer can be reset at any time by pressing and holding the Left button for two seconds when the "TM" is displayed on the screen. Note: Resetting Trip Timer will automatically reset Trip Distance and Average Speed. Backlight Odometer (ODO) Odometer is displayed on the lower screen. Just like a car, it measures distance ridden over time. After changing the computer battery, ODO will be set to zero. The odometer can be reset to the previous value by pressing and holding the Left button for two seconds when "ODO" is displayed on the screen. Average Speed (AVS) Average Speed is displayed on the lower screen. It represents the average speed while riding. Press the Right button until the "AVG" appears. The average speed is measured over the total cycling time for each trip. A figure can be expressed in Km/hr or M/hr. The average speed can be reset at any time by pressing and holding the Right button for two seconds when the AVS is displayed on the screen. NOTE: Resetting the Average Speed will automatically reset the Trip Timer and Trip Distance. Maximum Speed (MXS) Press the Right button until the "MXS" appears. This display will show the maximum speed during your ride. Maximum Speed can be reset at any time by pressing and holding the Left button for two seconds when the MXS is displayed on the screen. Hold either left or right main button for more than 1 second to activate the backlight feature & illuminate the display screen Troubleshooting Problem Possible Cause Recommended Action No speedometer display and/or no data reading Interference from electrical sources Move computer to different area Improper magnet/sensor alignment Ensure sensor & magnet are properly installed and aligned (p. 1) Poor battery contact or low/dead battery Replace battery Slow display response Temperature outside of operational limits (0-60°C or 32-140°F) Only use computer when temperature is within operational limits Display shows irregular features Poor battery contact or low/dead battery Replace battery Black display Temperature too hot or display exposed to sunlight too long Only use computer when temperature is within operational limits. Remove from sunlight Computer damaged or dropped Computer is broken FCC Warning Reset What’s Reset What’s Not Reset How Trip Reset Calories Burned (CAL) Trip Distance (DST) Trip Timer Average Speed (AVS) Clock Odometer (ODO) Maximum Speed Press both main left and right buttons down for 2 seconds This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Program Reset Above functions plus: Wheel Circumference KM or Mile Selection 12-24 Hour Format KG or LB Selection User Weight Clock Max Speed (MXS) Odometer Press YELLOW button on Left back of speedometer with a pencil tip Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. All functions, including Odometer (ODO) are reset (same as when you change the battery) Nothing Press RED button on Right back of speedometer with a pencil tip NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Total Reset However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment & receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. ©2006 Bell Sports, Inc. Rantoul, IL 61866 www.bellbikestuff.com Part #115238
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1.1-111 Instance ID : uuid:eed0b4f4-65df-11db-8574-000393c8375a Document ID : adobe:docid:indd:a209a28d-4305-11db-a373-85eee24851ad Rendition Class : proof:pdf Derived From Instance ID : 9ea19377-40c4-11db-a017-c5c84a367b55 Derived From Document ID : adobe:docid:indd:1ef10e5a-40b3-11db-a017-c5c84a367b55 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:1D7EB4E132A911DBA402AFD5715EC47D Manifest Reference Document ID : uuid:1D7EB4DF32A911DBA402AFD5715EC47D, uuid:06a3b323-0fb2-11da-bc5b-000a95ef3924, uuid:06a3b323-0fb2-11da-bc5b-000a95ef3924, uuid:06a3b323-0fb2-11da-bc5b-000a95ef3924, uuid:06a3b323-0fb2-11da-bc5b-000a95ef3924, adobe:docid:photoshop:cb2e2c0a-f536-11d9-b933-a297d996850e, adobe:docid:photoshop:7606d075-03fe-11da-990c-fe9d94bb3e84, adobe:docid:photoshop:09ea513c-03ff-11da-990c-fe9d94bb3e84, adobe:docid:photoshop:f8e616cc-66bb-11d7-b8e8-9e9f68a8fc04, adobe:docid:photoshop:f8e616cc-66bb-11d7-b8e8-9e9f68a8fc04, adobe:docid:photoshop:2c3e2286-03f9-11da-990c-fe9d94bb3e84, adobe:docid:photoshop:e855d6a9-03f8-11da-990c-fe9d94bb3e84, adobe:docid:photoshop:cb2e2c0a-f536-11d9-b933-a297d996850e Create Date : 2006:10:27 10:23:51-07:00 Modify Date : 2006:10:27 10:23:59-07:00 Metadata Date : 2006:10:27 10:23:59-07:00 Creator Tool : Adobe InDesign CS2 (4.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12659 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CS2 (4.0.4)EXIF Metadata provided by EXIF.tools