Bellmate T631W-2TX Wireless Controller User Manual

Bellmate Holdings Ltd. Wireless Controller

user manual

Download: Bellmate T631W-2TX Wireless Controller User Manual
Mirror Download [FCC.gov]Bellmate T631W-2TX Wireless Controller User Manual
Document ID1560455
Application IDGdqq9huwm2EulP6zmjAWzA==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize17.05kB (213151 bits)
Date Submitted2011-10-14 00:00:00
Date Available2011-10-14 00:00:00
Creation Date2011-10-11 18:26:01
Producing SoftwareAcrobat Distiller 7.0 (Windows)
Document Lastmod2011-10-12 08:41:02
Document TitleMicrosoft Word - User manual.rtf
Document CreatorPScript5.dll Version 5.2.2
Document Author: Vincent

T631W-2TX Operation Instruction
M Specification
1. Temperature display range: 0-40 ℃(32-99℉)
2. Temperature control range: 7-32℃(44-90℉)
3. Accuracy: ±1℉(at 68 ℉)
4. Power source: 2X AA 1.5V BATTERY
5. Load Rating: 1.5 Amp maximum
6. Static current: ≤
MA(DC3V)
7. Reading temperature current: ≤0.25MA(DC3V)
8. Backlight on current: ≤MA(DC3V)
9. Blue backlight
10. RF frequency: 916MHZ.
M T631W-2 TX:
When thermostat is connected with power, it will show full display and stay in
continuous transmission mode (it’s test mode), press “+”/”-“ key to enter into
normal mode.
M TEMPERATURE SETTING
Press “+”or “-“ to set temperature.
1.
2.
3.
FAN SETTING
In LOW position: GL is continuously on.
In HIGH position: GH is continuously on.
In AUTO position: it follows system to turn on or turn off.
M SYSTEM SWITCH SETTING
1. COOL: it runs in cool mode. When cooling is on, it will display “ON”.
2. OFF: system will not work.
3. HEAT: it runs in heat mode. When 1st heating is on, it will display “ON”. When 2nd
heating is on, it will display “+1”.
M Technical Setting
1. HEAT SWING SETTING
In HEAT mode, hold down “+” and “-”key for 3 seconds to flash “04” (factory default 0.4).
Press “+” or “-” key to set heat swing range from 02 to 20 (0.2 - 2.0) degree. It will
automatically confirm and exit in 15 seconds if no further key pressing.
2. COOL SWING SETTING
In cool mode, hold down “+” and “-”key for 3 seconds to flash “05” (factory default 05).
Press “+” or “-” key to set cool swing range from 0.2 to 2.0 (0.2 - 2.0) degree. It will
automatically confirm and exist in 15 seconds if no further key pressing.
3. CALIBRATION SETTING
In OFF mode, hold down “+” and “-”key for 3 seconds to display “CA” and flash “0”
(factory default 0). Press “+” or “-” key to set calibration range from -4 to 4 degree. It will
automatically confirm and exit in 15 seconds if no further key pressing.
4. B/O (for HEAT/COOL) SETTING
Last step don’t confirm, hold down “+” and “-”key at the same time to display “CO” and
flash “b” (factory default b). Press “+” or “-” key to select b or o. It will automatically
confirm and exit in 15 seconds if no further key pressing.
5. HEAT PUMP SETTING
Last step don’t confirm, hold down “+” and “-”key at the same time to display “HU” and
flash “OF” (factory default OF). Press “+” or “-” key to select ON or OF. It will
automatically confirm and exit in 15 seconds if no further key pressing.
6. HEAT LIMIT SETTING
Last step don’t confirm, hold down “+” and “-”key at the same time to display “HE” and flash “32”
(factory default 32). Press “+” or “-” key to set range 7-32. It will automatically confirm and exit in
15 seconds if no further key pressing.
7. COOL LIMIT SETTING
Last step don’t confirm, hold down “+” and “-”key at the same time to display “CL” and flash
“7” (factory default 7). Press “+” or “-” key to set range 7-32. It will automatically confirm
and exit in 15 seconds if no further key pressing.
8. LEARN
Last step don’t confirm, hold down “+” and “-”key at the same time to display “LE”. Hold “+”
key for 3 seconds to send learning code, LE will flash 3 times when it’s sending signal.
Press “+” or “-” key to exit. It will automatically confirm and exit in 15 seconds if no further
key pressing.
M JUMPER PIN SETTING
1. F/C: F=℉ ,C=℃
2. DELAY ON/OFF
ON: delay 5 minutes when compressor is on. It will flash “ON” during delay period. OFF:
without delay.
M ELEC/GAS SETTING (On PCB board)
1. In COOL mode it follows system with G to turn on or turn off (It’s not controlled by
ELEC/GAS).
2. In HEAT mode, if select ELECT, G follows system to turn on or turn off; if select GAS, G
is off.
M LOW VOLTAGE INDICATION
When AC power supply is disconnected, if batteries voltage is below 2.7V, it will display
symbol. If low voltage lasts for 21 days, it will enter into display SLEEP mode. LCD
only flash symbol. Press any key to resume normal display for 1 minute, then it returns display
SLEEP MODE.
M RESET
1. Press “RESET” key once (on the PCB board) to reset thermostat.
2. Hold down “+” key, then press “RESET” key
(on PCB) once to resume factory
defaults.
M T631W-2 RX SPECIFICATION
1. Power source: (1) 24V AC (18- 30V)
2. RF frequency: 916MHZ.
M T631W-2 TX and RX COMMUNICATION
1. Hold T631W-2RX key for 3 seconds, blue LED will flash.
2. Let T631W-2TX enter into learning status (step 8 on Technical setting), then hold “+” key for 3
seconds. Blue LED on RX will stop flash when learning code is successful.
When T631W-2RX connected with power, blue LED will be constantly on. It will flash 3
times when it received signal from TX. When relay is on, relevant LED will turn on.
If T631W-2 RX can’t receive signal from TX for 15 minutes, all relays will turn off (all
LED are off) until receive signal from TX.
M Line connector
R------------24VAC (system power supply)
HEAT=R TO W\Y
GL
C--------------COMMON24VAC(SYSTEM POWER SUPPLY)
W--------1 ST HEAT--------------------------Red LED
Y---------1 ST COOL--------------------------Blue LED
GH \GL------FAN----------------------------Green LED
B\O------------- HEAT\COOL-----------------Orange LED
COOL=R TO Y\GH
Statement according to FCC part 15.19:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Statement according to FCC part 15.105:
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver
isconnected.
. Consult the dealer or an experienced radio/TV technician for help.
Statement according to FCC part 15.21:
Modifications not expressly approved by this company could void the user's authority to operate the
equipment.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Vincent
Create Date                     : 2011:10:11 18:26:01+08:00
Modify Date                     : 2011:10:12 08:41:02+07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:10:12 08:41:02+07:00
Format                          : application/pdf
Title                           : Microsoft Word - User manual.rtf
Creator                         : Vincent
Document ID                     : uuid:798b06af-05cf-4e83-9e9e-6c695436c621
Instance ID                     : uuid:639586c0-6446-4126-b7cd-356907941379
Page Count                      : 4
EXIF Metadata provided by EXIF.tools
FCC ID Filing: UX2T631W-2TX

Navigation menu