Bematech BR-200 Handy Wireless Scanner User Manual

Bematech S.A. Handy Wireless Scanner

User manual

Handy Wireless Scanner ii USER’S MANUAL Important Notice No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein nor for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval. No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any human or computer or other language in any form or by any means electronic, mechanical, magnetic, optical, chemical, biological, manual or otherwise, except for brief passages which may be quoted for purposes of scholastic or literary review, without express written consent and authorization. We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for information only and is subject to change without notice. All trademarks mentioned herein, registered or otherwise, are the properties of their various, ill, assorted owners. General Handling Precautions Do not dispose the scanner in fire. Do not put the scanner directly in the sun or by any heat source. Do not use or store the scanner in a very humid place. Do not drop the scanner or allow it to collide violently with other objects. Do not take the scanner apart without authorization Guidance for Printing This manual is in A5 size. Please double check your printer setting before printing it out. When the barcodes are to be printed out for programming, the use of a high-resolution laser printer is strongly suggested for the best scan result. Copyright © 2014. All rights reserved.
USER’S MANUAL Radio Notice This equipment generates uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class A computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC rules. These specifications are designed to provide reasonable protection against interference when operated in a commercial environment. Radio and Television Interference Operation of this equipment in a residential area can cause interference to radio or television reception. This can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: - Reorient the receiving antenna. - Relocate the device with respect to the receiver. - Move the device away from the receiver. - Plug the device into a different outlet so that the device and the receiver are on different branch circuits. If necessary the user may consult the manufacturer, and authorized dealer, or experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, DC 20402 U.S.A., Stock No. 04000003454. 0 Laser Safety This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions in this manual, it may cause interference to radio communications. The equipment has been tested and found to comply with the limits for a Class A computing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of FCC Rules. These specifications are designed to provide reasonable protection against interference when operated in a commercial environment. Radiant Energy: The laser scanner uses one low-power visible laser diodes operating at 650nm in an opto-mechanical scanner resulting in less than 3.9μW radiated power as observed through a 7mm aperture and averaged over 10 seconds. Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside. Handy Wireless Scanner iii
Handy Wireless Scanner iv USER’S MANUAL Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner engine, while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately. Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user-serviceable parts inside. Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and microscopes but do not include normal eye glasses worn by the user. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. For CE-Countries This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to maintain CE conformance. Power Supply  Use only the type of battery and the charging equipments that came with your scanner.  Using any other type of battery and charging equipment may damage the scanner and invalidate the warranty.  Do not short the battery terminals. The battery could overheat.  Do not attempt to split or peel the outer casing.  Remove the battery if the scanner is not going to be used for a long time. If the battery is left unused for more than 3 months, you need to charge the battery before use.
USER’S MANUAL Handy Wireless Scanner v Wireless Communication  Wireless technology operates 100M / 75M with communication dongle. Maximum communication range may vary depending on obstacles (person, metal, wall, etc.) or electromagnetic environment.  The following conditions may affect the sensitivity of wireless communication.  There is an obstacle such as a person, metal, or wall between this unit and wireless device.  A device using 2.4 GHz frequency, such as a wireless LAN device, cordless telephone, or microwave oven, is in use near this unit.  Because wireless devices and wireless LAN (IEEE802.11b/g) use the same frequency, microwave interference may occur and resulting in communication speed deterioration, noise, or invalid connection if this unit is used near a wireless LAN device. In such a case, perform the following.  Use this unit at least 10 m (about 30 ft) away from the wireless LAN device.  If this unit is used within 10 m (about 30 ft) of a wireless LAN device, turn off the wireless LAN device.  Install this unit and wireless device as near to each other as possible.  Microwaves emitting from a wireless device may affect the operation of electronic medical devices. Turn off this unit and other wireless devices in the following locations, as it may cause an accident.  Where inflammable gas is present, in a hospital, train, airplane, or a petrol station  Near automatic doors or a fire alarm  This unit supports security capabilities that comply with the wireless standard to provide a secure connection when the wireless technology is used, but security may not be enough depending on the setting. Be careful when communicating using wireless technology.  We do not take any responsibility for the leakage of information during wireless communication.  Connection with all wireless devices cannot be guaranteed.  A device featuring wireless function is required to conform to the wireless standard specified by wireless SIG, and be authenticated.  Even if the connected device conforms to the above mentioned wireless standard, some devices may not be connected or work correctly, depending on the features or specifications of the device.  Depending on the device to be connected, it may require some time to start communication. Tips to help improve your wireless network 1. Position the access point (host/dongle) in a relatively empty space at central location. When possible, place the access point in a central location on the high ground (1m or above). If your access point is against an outside wall, the signal will be weak on the other side of the room. X Bad host placement O Good host placement
USER’S MANUAL Handy Wireless Scanner vi X Bad host placement O Good host placement At least 1 m2. Move the access point (host/dongle) off the floor and away from walls and metal objects (such as metal file cabinets). Metal objects, walls, and floors will interfere with your wireless signals. The closer your access point is to these obstructions, the more severe the interference, and the weaker your connection will be. 3. Reduce wireless interference. The most common wireless technology, 802.11g (wireless-G), operates at a frequency of 2.4 gigahertz (GHz). Many cordless phones, microwave ovens, hospital equipments, refrigerator, LED, and other wireless electronics also use this frequency. If you use these wireless devices in your office, your device might not be able to "hear" the signals over the noise coming from them. If your network uses wireless-G, you can quiet the noise by avoiding wireless electronics that use the 2.4 GHz frequency. Instead, look for cordless phones and other devices that use the 5.8 GHz or 900 megahertz (MHz) frequencies. Because 802.11n (wireless-N) operates at both 2.4 GHz and the less frequently used 5.0 GHz frequency, you may experience less interference on your network if you use this technology. Avoid possible wireless interference4. Update the firmware or driver of your wireless dongle. If you are using a wireless dongle or other similar devices to make the connection, getting the latest firmware or driver updates may improve the performance. Visit your manufacturer’s website for the updates.
Handy Wireless Scanner vii USER’S MANUALTable of Contents Important Notice..................................................................................................................ii General Handling Precautions..............................................................................ii Guidance for Printing ...........................................................................................ii Laser Safety .........................................................................................................iii For CE-Countries..................................................................................................iv Power Supply ......................................................................................................iv Wireless Communication .....................................................................................v Introduction .........................................................................................................................1 Scanner and Accessories..............................................................................................2 Charging the Battery ....................................................................................................4 Power on the Scanner..................................................................................................5 Function Button ...........................................................................................................5 How to Scan .................................................................................................................6 Radio Communication Host Type.................................................................................7 Dongle Host Mode ...............................................................................................7 SPP Master/SPP Slave Mode................................................................................7 HID Mode .............................................................................................................7 Scanner USB online to Host .........................................................................................8 USB Online Mode.................................................................................................8 Visible Indicators..........................................................................................................8 Scanner LED..........................................................................................................8 Dongle LED ...........................................................................................................9 Sound Indicators ..........................................................................................................9 ACK/NAK Protocol or Frame Packing..........................................................................10 Scanner to Remote Application..................................................................................11 Barcode Type Table ....................................................................................12 Programming Guide ...........................................................................................................13 Connecting to a Host..................................................................................................17 USB Online Mode...............................................................................................17 Disable USB communication ......................................................................17 Enable USB communication .......................................................................17 Set USB as the primary connection............................................................17 Dongle Host Mode .............................................................................................18 Dongle Host Pairing....................................................................................18 Wireless Mode...................................................................................................19 SPP Slave Mode..........................................................................................19 SPP Master Mode.......................................................................................20 HID mode ...................................................................................................21 Setting Pin Code .........................................................................................22 Deleting pin code .......................................................................................22
Handy Wireless Scanner viii USER’S MANUAL Reset Name ................................................................................................22 Setting Name..............................................................................................23 Wireless Discovery .....................................................................................23 Data Transmit Method .......................................................................................24 Normal .......................................................................................................24 Out of Range ..............................................................................................24 Batch Mode................................................................................................25 Clearing Batch ............................................................................................25 Batch Transfer.............................................................................................26 Batch Mode Sounds Settings......................................................................26 System Function Settings ...........................................................................................27 Scan Mode .........................................................................................................28 Radio Communication Setting............................................................................29 Dongle Host mode......................................................................................29 USB Online mode .......................................................................................29 HID mode ...................................................................................................30 SPP Master/Slave mode .............................................................................30 Device Setting.............................................................................................30 Data Transmit Mode...................................................................................32 Radio protocol communication parameter ................................................33 Power off timeout parameter ....................................................................34 Same Code Delay........................................................................................35 Operation Function Setting ................................................................................37 Good Read Beeper Tone Selection .............................................................37 Beeper duration Selection..........................................................................38 Inter Character Delay .................................................................................39 Inter Message Delay...................................................................................39 Interface Settings ...............................................................................................40 RS-232C Interface Setting...........................................................................40 USB Interface Setting..................................................................................41 Smart Phone Software Keypad Control Setting..........................................43 The Symbologies ................................................................................................44 Codabar Parameter Setting........................................................................44 Code 39 Parameter Setting ........................................................................46 Code 93 Parameter Setting ........................................................................48 Code 128 Parameter Setting ......................................................................49 Chinese Post Code Parameter Setting........................................................50 MSI/Plessy Parameter Setting ....................................................................51 Code 11 Interface Setting...........................................................................52 ITF 2 of 5 Parameter Setting.......................................................................53 Standard 2 of 5 Parameter Setting .............................................................55 Industrial 2 of 5 Parameter Setting ............................................................56
Handy Wireless Scanner ix USER’S MANUALUPC/EAN/JAN Parameter Setting ...............................................................57 Telepen Parameter Setting.........................................................................62 Matrix 2 of 5 Parameter Setting.................................................................63 Data Editing........................................................................................................67 Identifier Code ...........................................................................................67 Header and Trailer......................................................................................69 Full ASCII Code 39 Table .............................................................................70 Appendix 1: USB Virtual COM Driver Installation ..............................................75 Appendix 2: Barcode Length Setting ..................................................................76
USER’S MANUAL Handy Wireless Scanner 1 Introduction Designed for optimal reading performance, the compact Z-325xBT offers wide scanning range and wireless communication technology for easy handling of any applications. Z-325xBT includes a 32-bit CPU and excellent scan engine in a small yet powerful unit delivering intuitive and rapid scanning regardless of environment. Key Features:  Compact, light weight, and portable  Compatible with iOS devices such as iPad/iPhone  32-bit microprocessor Micro USB slotBack Cover LockLED Indicator Battery Compartment ScanWindowPower Button/Scan Trigger Function Button/Off Button Hand Strap Hole
USER’S MANUAL Handy Wireless Scanner 2 Scanner and Accessories The scanner package contains: Wireless scanner with battery Dongle Micro USB cable 5V USB Power adapter Quick Guide If any contents are damaged or missing, please contact your dealer immediately.
USER’S MANUAL Handy Wireless Scanner 3 Battery Installation Installing Batteries Please follow the steps below to install the batteries. Always use the rechargeable batteries provided by the manufacturer to avoid any non-compatible danger or void the warranty. 1. Move the lock for the battery compartment to the unlock position and remove the back cover. 2. Align the metal contact on the battery with the metal contact inside the battery compartment and insert the battery. 3. Place the back cover back on the scanner and move the lock to the lock position.
USER’S MANUAL Handy Wireless Scanner 4 Charging the Battery To charge the battery using the USB cable: There are two method to charge scanner via USB cable.  Host USB Power  Power adaptor 1. Connect the micro USB connector directly to the scanner. 2. Connect the other end of the USB connector to the host to begin charging. You can also connect the USB cable to an outlet using the power adapter to charge the battery. 3. The battery begins charging when the scanner LED indicator starts flashing green. LED turns steady green when charging is complete.  The scanner will power on automatically when charging.  Batteries shipped may not be full charged and should be fully charged for maximum charge capacity.  Recommended charging environment is temperature in 0°C~35°C (32° F~95°F).
USER’S MANUAL Handy Wireless Scanner 5 Power on the Scanner 1. Ensure the battery is fully charged. Please refer to the previous section to charge the battery. 2. Press and hold the power button for 1 second until a long beep sound is heard to turn on the scanner. 3. To power off the scanner press and hold the function / off button for 3 second until 2 short beeps are heard. Power on Power off Function Button The function button can be used as the power off key or to call or hide virtual keyboard when the scanner is connected with iPad, iPhone or other devices (not including Android devices). Press function button to call or hide the keyboard
USER’S MANUAL Handy Wireless Scanner 6 How to Scan There are two ways to scan with this device.  Handheld scanning  Presentation scanning Handheld scanning 1. Power on the scanner. 2. Press the scan trigger and aim at the barcode. 3. When decoding is successful, the scanner beeps and the LED indicates blue. Presentation Scanning 1. Set the scanner for presentation scanning mode. 2. Move the barcode label approach the scanner scanning zone. 3. When decoding is successful, the scanner beeps and the LED indicates blue.
USER’S MANUAL Handy Wireless Scanner 7 Radio Communication Host Type This scanner support three radio communication types:  Dongle mode  SPP master/slave mode  HID mode Dongle Host Mode The scanner communicates with the host through the dongle. One dongle can be used to connect multiple scanners. Typically, scanner and dongle in the same delivery box are paired in factory. As soon as both are powered on, they should find and connect to each other immediately. However, under special circumstance that the scanner and the dongle are not paired with the dongle, please follow instructions in later chapters to pair the dongle. SPP Master/SPP Slave Mode The scanner can communicate with the host through wireless connection. Please see Wireless Mode for detail operation information. HID Mode The scanner communicates with the smart phone through HID connection. Please see HID mode for detail operation information
USER’S MANUAL Handy Wireless Scanner 8 Scanner USB online to Host The scanner provides other ways for you to connect to the host. When the radio communication is not available, the scanner can be connected to transmit data via USB Online mode. Please see USB Online Mode for detail operation information. USB Online Mode The scanner connects directly to a USB host to recharge and transmit data. Visible Indicators Scanner LED Please see the following for the operational indication of the scanner. LED Status Indication Blue flashing Waiting for radio connection (flash time 0.5s : 0.5s). Blue fast flashing Radio connecting. Blue slow flashing Device connected (flash time 0.03s : 3s). Blue flash once A barcode was decoded successfully Blue fast flashing Data transmission Green flashing Charging mode Steady green Battery fully charged Steady red Programming mode Red flashing slow (with continuous beep sound) Low battery warning Red flash twice (with 2 beep sound) Very low battery warning
Handy Wireless Scanner 9 USER’S MANUALDongle LED Please see the following for the operational indication of the scanner. LED Status Indication Blue flashing Dongle is detected by the host, communication not yet established Steady blue Dongle is connected to the host Blue flash once Data transmission Steady red Dongle is plugged into the host but not detected by the host or dongle is in the update mode Sound Indicators When the scanner is in operation, it provides audible feedback. The beeps indicate the status of the scanner. Beep Indication A long beep Power on scanner. One beep A barcode has been successfully decoded and data is either transfer to the host or saved in the memory. 1 high - low - high beeps Scan dongle pair barcode. Four short medium beeps Data communication failed or out of range. Intermission medium-low beeps Low battery warning. 1 short medium – low beeps Scanner is power down. 1 long high – medium beeps Enter programming mode. 1 long medium - medium beeps Exit Programming mode.
USER’S MANUAL Handy Wireless Scanner 10 ACK/NAK Protocol or Frame Packing When scanner is in SPP Master/Slave mode, and add in the data protocol or packing could confirm the data reliability. Refer to below for different setting options:
Handy Wireless Scanner 11 USER’S MANUALScanner to Remote Application Data Format of Packet To send a data (barcode) to the remote application, the scanner has to encapsulate it: EAH (Header) Size of payload FEH (Format Byte) Data ID Data BarcodeType AEH (End of Byte) Reserved Byte 1 byte 1 byte 1 byte 1 byte Varies 1 byte 1 byte 1 byte Title Definition Header Character (EAH) The character ID at the head of every data. It has to start with EAH. Size of Payload The encapsulated data length excluding header character. Format Byte (FEH) Differentiate data format; barcode data is always FEH. Data ID The number of each data. If receive the same ID more than once, only the first one is valid, delete the rest. Barcode Type (1 byte) Please refer to the Barcode Type Table. Data Decoded barcode data. End of Byte (AEH) Record data ends. Reserved Byte Reserved for future use. Example: If Code39 barcode data is "ABCD", than sender sends out: EAH + 0AH + FEH + ID + "ABCD "+ 11H+AEH + Reserved Byte 0AH = 1+1+1+4+1+1+1 Acknowledge packet 55H (Header ) Data ID 55H (end of byte) 1 byte 1 byte 1 byte Example: If scanner sends out: EAH , 0AH , FEH , 01H , "ABCD ", 011H, AEH , EEH Remote acknowledges: 55H +01H + 55H
USER’S MANUAL Handy Wireless Scanner 12 Barcode Type Table Code Value Code39 0x11 Codabar 0x01 Code128 0x03 Interleaved 2/5 0x02 Code93 0x06 UPC-E 0x14 UPC-A 0x24 EAN-8 0x34 EAN-13 0x44 Chinese Post Code 0x05 MSI 0x07 Firmware Update To update the firmware, scan the Start of Configuration barcode then scan Dongle USB Update or Scanner USB Update to enter Firmware Update mode. To exit Firmware Update mode without updating, please remove and re-insert the battery. Start Of Configuration Dongle USB Update Update firmware using dongle (Dongle Host mode only) Scanner USB Update Update firmware using USB connection
USER’S MANUAL Handy Wireless Scanner 13 Programming Guide Program Procedure Using Barcode Manual 1. Power up the scanner. 2. Scan the Start of Configuration barcode. 3. Scan the barcode for the desired feature. Multiple features can be enabled/disabled before scanning the End of Configuration barcode. 4. Scan the End of Configuration barcode and save the new configuration. Power off and on the scanner when the setting is done. 5. To give up a configuration change, power off the scanner before scanning the End of Configuration barcode or scan the Abort barcode. 6. For some parameter setting, such as barcode length and identifier code, it is required to scan the Set barcode to save the configuration. Scan barcode of the desired feature Discard the configurationFinish the configuration Power off the scannerScan the “Abort”barcode Scan the “End of Configuration” barcode Scan the “Start of Configuration” barcode Power up the scanner
Handy Wireless Scanner 14 USER’S MANUAL Default Parameters The factory default setting table gives the default settings of all the programmable parameters. The default settings will be restored whenever the "Reset" programming label is scanned and the scanner is in programming mode. Default values are highlighted in grey background in the settings. Factory Default Setting Parameter Default Radio communication Wireless host Dongle Pairing mode Unlocked Data transmit Normal Radio protocol timeout 5 seconds Power off timeout 20 minutes Encryption Enable Dongle Host RS-232 communication Terminator <CR><LF> USB Communication Terminator Enter Code mode Scan code Keyboard US keyboard Pair contact on dongle Enable Scanner Decoder Selection Default EAN/UPC Enable CODE 39 Enable Code 32 Disable CODABAR Enable ITF 2 OF 5 Enable MSI Disable Chinese post code Disable Code 93 Enable Code 128 Enable EAN-128 Disable Telepen Disable Code 11 Disable
Handy Wireless Scanner 15 USER’S MANUALStandard 2 of 5 Disable Industrial 2 of 5 Disable GS1 DataBar Disable Beeper Sound Default Frequency Medium Duration Medium Operating Parameter Default Scan mode Trigger mode Stand mode Enable Header and trailer None Inter-message delay None Inter-character delay None Code Identifiers Default Identifier code as ZEBEX standard Disable Identifier code as AIM standard Disable Code 39 identifier code M ITF 2 of 5 identifier code I Chinese post code identifier code H UPC-A identifier code A UPC-E identifier code E EAN-13 identifier code F EAN-8 identifier code FF Codabar identifier code N Code 128 identifier code K Code 93 identifier code L MSI identifier code P Code 11 identifier code O Standard 2 of 5 identifier code S Industrial 2 of 5 identifier code D GS1 DataBar identifier code RS GS1 DataBar Limited identifier code RL GS1 DataBar Expanded identifier code RX
Handy Wireless Scanner 16 USER’S MANUAL Default Data Transmit Format Code Message format EAN-13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13EAN-8 D1 D2 D3 D4 D5 D6 D7 D8 UPCA D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 UPCE D1 D2 D3 D4 D5 D6 D7 D8 CODE128 D1-Dx (default 3~62) EAN128 C1 D1-Dx (default 3~62) CODE39 D1-Dx (default 3~62) CODABAR D1-Dx (default 6~32) INTERLEAVED 2/5 D1-Dx (default 6~32) CHINESE POST CODE D1-Dx (default 8~32) CODE93 D1-Dx (default 3~32) MSI D1-Dx (default 6~32)
USER’S MANUAL Handy Wireless Scanner 17 Connecting to a Host The scanner provides several data transmit methods to communicate with the host. User may select the method according to their preferences. Read this section to learn the setups for connecting to different hosts. Start Of Configuration USB Online Mode The scanner connects directly to a USB host to recharge and transmit data. You may enable or disable the functions using the following settings. Disable USB communication USB online scan disable Disable USB communication. Enable USB communication USB online scan enable Wireless connection as the primary communication option to the host. USB connection is only used when wireless is disconnected. Set USB as the primary connection USB online scan, Ignore radio communication USB connection as the primary communication option to the host when it is available. Wireless mode is set as the secondary option. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 18 Start Of Configuration Dongle Host Mode The scanner communicates with the host through the dongle. Typically, scanner and dongle in the same delivery box are paired and corresponded to host interface in factory. To check if the scanner is paired to the dongle, check the scanner LED group1 for slow blue flash and check the top dongle LED for steady blue light. If LED group1 of scanner and top LED of dongle are both flashing blue, follow the steps below to radio connect the scanner and dongle. Dongle Host Pairing 1. Please make sure the scanner LED is flashing blue indicating it’s not linked to any host. If the LED shows steady blue, the scanner is already paired to another scanner so you must unpair the scanner before continuing. 2. Power on the scanner and enable dongle host mode if necessary. Dongle Host mode enableEnable dongle mode with this setting 3. Use the scanner to scan the pairing barcode at the bottom of the dongle to begin pairing. 3 short beeps will be heard. 4. The LED indicator on the scanner will flash blue rapidly indicating search mode in process. The LED on the dongle becomes steady blue when the pairing is successful. 5. Scan the corresponding host interface the dongle is using to begin using the scanner. Return to USB default Return to dongle USB communication. (Communication dongle link required) Return to Virtual COM Port default Return to Virtual COM Port setting End Of Configuration
USER’S MANUAL Handy Wireless Scanner 19 Start Of Configuration Wireless Mode The scanner connects to the host via wireless connection. You may select SPP Master or SPP Slave for PC connection or select HID mode and Smart phone mode for smart phone connection. SPP Slave Mode In this mode, the scanner connects to the host /PC via wireless connection and performs like there’s a serial connection. In SPP Slave mode, the scanner is discoverable from a remote device and it can request the scanner for connection. There are several ways to connect the wireless scanner to your PC. If you have your own applications please check their User’s Manuals for pairing instructions. To connect a wireless device to Window based system for the first time: 1. Turn on the host computer and activate its wireless connection. 2. Select “Add Bluetooth device”. Or open the dialog Bluetooth devices and click “Add”. 3. Power on the scanner and program it with “SPP Slave mode” label. Scanner SPP Slave enable Enable wireless SPP Slave mode. 4. On Devices tab, click Add. This will open the Add Bluetooth Device Wizard. 5. Select the "My device is set up and ready to be found" checkbox, and then click Next. 6. The scanner should be on the list of discoverable devices. The default name of the scanner is “Z-325X BT”. Select “Z-325X BT” and click “Next”. 7. Select “Let me choose my own passkey” and enter the pin code. The default pin code is “12345678. 8. Click “Next” to connect the scanner to the host. A short beep should be heard upon connection. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 20 Start Of Configuration SPP Master Mode In this mode, the scanner connects to the host /PC via wireless connection and performs like there’s a serial connection. In master mode, the scanner initiates the connection to the remote device. 1. Power on of the remote device and have its address ready in hand and make it discoverable. 2. Program the scanner with the “SPP Master enable” barcode. Scanner SPP Master enable Enable SPP Master mode. 3. Scan “Set device address” to set the address. Set device address (SPP Master only) Set device address for SPP Master connection. 4. Use the ASCII table in Programming Guide to input the 12 digit device address. For example: if the address is “011B1345600”, scan “0”, “0”, “1”, “1”, “B”, “1”, “3”, “4”, “5”, “6”, “0”, “0” from ASCII barcode labels. 5. Scan “Confirm Setting” to store the address. Confirm Setting (for address and pin code setting required) 6. Setup and input the pin code if necessary. Please see Setting Pin Code section for more details. 7. Scan “Required Pair with slave (SPP Master)” to begin pairing. Required Pair with slave (SPP Master) In SPP Master mode, you can scan the device address label on the Quick Guide instead of using the ASCII table to scan in the address. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 21 Start Of Configuration HID mode In HID mode, the scanner connects to the host /PC via wireless connection and performs like there’s a keyboard connection. The scanner initiates the connection to the remote device. 1. Power on the scanner and program it with “HID Mode”. To connect a smart mobile phone (for example, iPhone, Android), the Smart phone mode must also be enabled. Power off the scanner when the setting is done. HID mode Enable wireless HID keyboard emulation Smart phone modeFor smart phone mode (HID MODE must also be enabled). 2. Enable wireless connection on your host and follow the instructions in your host to set it to discover other wireless devices in its surrounding. 3. The scanner should be on the list of discoverable devices. The default name of the scanner is “Z-325X BT”. You will be prompt to enter paring pin code. Select “Z-325X BT” and input the pin code that appears on your mobile device to connect scanner to the phone. 4. Scan the Enter barcode to confirm. A short beep should be heard upon connection. Enter Full ASCII ---CR Function key-----“Enetr(num.)” End Of Configuration
USER’S MANUAL Handy Wireless Scanner 22 Start Of Configuration Setting Pin Code 1. To change the pin code, use the “Set pin code” setting. Default is “12345678”. 2. Use the ASCII table in Programming Guide to input the new code (must be at least 4 digits and not more than 8 numeric digits). 3. Scan “Save Setting” to store the pin code. Set pin code Set pin code (SPP Master only) Confirm Setting (for address and pin code setting required) Please check the User’s Manual from your PC for device address and pin code. Deleting pin code To delete pin code, use the “Delete pin code setting”. Delete pin code Delete the stored pin code. Reset Name To change the scanner name back to the default name “Z-325x BT” use the “Default device name” setting. Default device name Change device name back to default “Z-325x BT”. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 23 Start Of Configuration Setting Name 1. To change the name displayed when the scanner is discovered, scan the “Friendly device name set” label. Default name is “Z-325X BT”. 2. Use the ASCII table in Programming Guide to input the name (Max.12 digits). 3. Scan “Confirm Setting” to store the new name. Friendly device name set Change the display name when scanner is discovered. Confirm Setting (for address and pin code setting required) Wireless Discovery Use the following settings to show or hide the device from wireless discovery. Discover enable Make scanner visible to wireless device. Discover disable Make scanner invisible to wireless device. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 24 Start Of Configuration Data Transmit Method The data transfer method includes three types: Normal (default), Out-of-Range Mode, and Batch Mode. Users may modify this setting according to their preferences. Normal When the scanner is within the connection range, the scanned data will be transferred to the host computer immediately. If the scanner is out of its connecting range, the scanner does not send or store any data. Data transmit normal Batch mode is disabled. Out of Range Scanned data are stored when scanner is out of its wireless communication range. When scanner is back into its communication range or re-connected, the stored data are sent when scanning next barcode label. Out of range buffer enable Enable out of range mode. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 25 Start Of Configuration Batch Mode Whether within the connection range or not, in batch mode, the scanner stores all scanned data that will be transferred to the host computer after scanning “Send Batch Data” label. Number of storable bar codes = 61,365 bytes of memory / (number of characters in the bar code +2) Batch mode Note: Scanner LED indicator will not flash while waiting for connection in this mode. Clearing Batch Use the settings in this section to clear the stored data. Clear batch data after send Saved data are cleared after they are transferred to the host. Clear batch data by scanning “Delete batch data” label Scan this label then scan “Save Setting” to delete the stored batch data. Delete batch data Same as previous setting but with alert sound. Confirm Setting (for address and pin code setting required) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 26 Start Of Configuration Batch Transfer Use the settings in this section to setup batch transfer. Send Batch Data By Scanning Label Scanning this label automatically exits you from the Programming Mode. Press and hold the trigger for over 1 second to send the data. Send Batch Data on line USB cable contact Data is ready to be transferred upon USB connection. Press and hold the trigger for over 1 second to send the data. Batch Mode Sounds Settings Use the settings in this section to setup the sound. Out of range resend data with beeper sound Add beeper sound when resending data in Out of range mode. Out of range resend data without beeper sound in Out of range mode. No beeper sound when resending data Send Batch Data without beep No beep when sending data. Good-read LED will light up until the transfer is done. Send Batch Data with Beep Beep sound when sending data. Good-read LED will light up until the transfer is done. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 27 System Function Settings Default values are highlighted in grey background. Start Of Configuration Barcode Value Description Return scanner to factory defaults Return dongle host to factory defaults Return to USB default (Communication dongle link required) Return as USB-virtual COM port default (Communication dongle link required) Return as OPOS port default Function Button Enable Enable the function/off button Function Button Disable Disable the function/off button End Of Configuration
USER’S MANUAL Handy Wireless Scanner 28 Start Of Configuration Barcode Value Description Display firmware version Abort (exit programming mode without any updates) Scan Mode Trigger mode The scanner becomes inactive as soon as the data is transmitted. It must be triggered to become active again. Auto scan mode The scanner is still active after the data is transmitted but the successive transmission of the same barcode is not allowed when the trigger switch is pressed again. Alternate mode The scanner illumination alternates between on and off when the trigger switch is pressed. Presentation mode Also called auto trigger mode. The scanner is inactive but will automatically detect barcodes presented in the scan zone and become active. Idle mode enable Idle mode disable Disable Idle mode. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 29 Start Of Configuration Radio Communication Setting Dongle Host mode Dongle Host mode enable Enable dongle mode with this setup. Unlock pairing mode In this mode, the scanner can pair with another dongle when disconnected. Lock pairing mode. In this mode, the scanner can not pair with another dongle. Undo pairing Undo the pairing between the dongle and the scanner. USB Online mode USB online scan disable USB online scan enable USB online scan, Ignore radio communication End Of Configuration
USER’S MANUAL Handy Wireless Scanner 30 Start Of Configuration HID mode HID mode (Combo keyboard) For Apple mode SPP Master/Slave mode Scanner SPP Master enable SPP Master (Connect wireless address “BxxxxxxxxxxxxT” in CODE39 format) Scanner SPP Slave enable Setting wireless address (SPP Master only) Set PIN code (SPP Master only) Device Setting Show device address after friendly name enabled Enable showing device address xx:xx:xx after device name during discovery Show device address after device friendly name disabled Disable showing device address xx:xx:xx after device name during discovery End Of Configuration
USER’S MANUAL Handy Wireless Scanner 31 Start Of Configuration Default Device name Friendly device name set Delete pin code Confirm Setting (for address, device name, and pin code setting required) Required Pair with slave (SPP Master) Discover enable Discover disable Encryption enable Encryption disable Data communication without protocol Data communication with ACK/NAK protocol Data communication with Packing protocol End Of Configuration
USER’S MANUAL Handy Wireless Scanner 32 Start Of Configuration Data Transmit Mode Data transmit normal Out of range buffer enable Batch mode Send Batch Data By Scanning Label Clear batch data after send Clear batch data by scanning “Delete batch data” label Delete batch data Send Batch Data on line USB cable contact. Send Batch data on dongle Out of range resend data with beeper sound Out of range resend data without beeper sound Send Batch Data without Beep Send Batch Data with Beep End Of Configuration
USER’S MANUAL Handy Wireless Scanner 33 Start Of Configuration Radio protocol communication parameter Radio protocol timeout= 3 sec Radio protocol timeout= 5 sec Radio protocol timeout =8 sec Radio protocol timeout= 10 sec Radio protocol timeout =13 sec Radio protocol timeout =16 sec Radio protocol timeout= 20 sec End Of Configuration
USER’S MANUAL Handy Wireless Scanner 34 Start Of Configuration Power off timeout parameter Power off timeout=5 min Power off timeout=10 min Power off timeout=20 min Power off timeout=30 min Power off timeout=1 hr Power Off timeout : 2 hr Power Off timeout : 4 hr Power Off timeout : 6 hr Power Off timeout : 8 hr End Of Configuration
USER’S MANUAL Handy Wireless Scanner 35 Start Of Configuration Power Always On Power off by scanning this label Link beeper enable Link beeper disable Power-up beeper enable Power-up beeper disable Same Code Delay 50 msec 100 msec 200 msec 300 msec End Of Configuration
USER’S MANUAL Handy Wireless Scanner 36 Start Of Configuration 400 msec 500 msec 600 msec 700 msec 800 msec 1000 msec Infinite End Of Configuration
USER’S MANUAL Handy Wireless Scanner 37 Start Of Configuration Operation Function Setting Good Read Beeper Tone Selection Medium beeper tone High beeper tone Low beeper tone Speaker disable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 38 Start Of Configuration Beeper duration Selection Long Medium Short Ultra Short Ultra Long End Of Configuration
USER’S MANUAL Handy Wireless Scanner 39 Start Of Configuration Inter Character Delay 0 ms 2 ms 5 ms 10 ms 20 ms 50 ms Inter Message Delay 0 ms 100 ms 500 ms 1000 ms End Of Configuration
USER’S MANUAL Handy Wireless Scanner 40 Start Of Configuration Interface Settings RS-232C Interface Setting Start Of Configuration Message Terminator RS-232 message terminator—none RS-232 message terminator—CR/LF RS-232 message terminator—CR RS-232 message terminator—LF RS-232 message terminator—H tab RS-232 message terminator—STX/ETX RS-232 message terminator—EOT End Of Configuration
USER’S MANUAL Handy Wireless Scanner 41 Start Of Configuration USB Interface Setting USB Setting International Keyboard mode ( ALT method) Keyboard language support---USA Keyboard language support---UK send scan code Keyboard language support---GERMANY Keyboard language support---FRENCH send scan code Keyboard language support---SPANISH send scan code Keyboard language support---ITALIAN send scan code Keyboard language support---Switzerland send scan code Keyboard language support---Belgium send scan code Keyboard language support---Japanese Capital lock on Capital lock off Function key emulation enable Function key emulation disable Send number as normal data Send number as keypad data End Of Configuration
USER’S MANUAL Handy Wireless Scanner 42 Start Of Configuration Message Terminator Keyboard terminator---none Keyboard terminator---Enter Keyboard terminator---H-TAB End Of Configuration
USER’S MANUAL Handy Wireless Scanner 43 Start Of Configuration Smart Phone Software Keypad Control Setting Smart Phone Software Keypad Control Multi-media keyboard mode  This option enables Multi-media keyboard mode Software keypad enable/disable  This option enable or disable Software keypad To enable/disable Software keyboard: 1. Scan the Start Of Configuration barcode. 2. Scan the Multi-media keyboard mode barcode. 3. Scan the End Of Configuration barcode. 4. Connect the scanner with a smart phone. Please see HID mode for instructions. 5. With Multi-media keyboard mode enabled and smart phone connection made, you may scan the Software keypad enable/disable barcode to enable or disable the Software keypad. End Of Configuration
USER’S MANUAL Handy Wireless Scanner 44 Start Of Configuration The Symbologies Codabar Parameter Setting Barcode Value Barcode Label Description RC02 Codabar enable RD02 Codabar disable CB05 Codabar start/stop character transmission－none CB06 Codabar start/stop character transmission－A,B,C,D CB07 Codabar start/stop character transmission－DC1~DC4 CB08 Codabar start/stop character transmission－a/t,b/n,c/*,d/e CB09 Codabar maximum length setting CB10 Codabar minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 45 Start Of Configuration Barcode Value Barcode Label Description CB13 No check character CB14 Validate modulo 16,but don’t transmit CB15 Validate modulo 16 and transmit DC50 Codabar data redundant check=off DC51 Codabar data redundant check=1 DC52 Codabar data redundant check=2 DC53 Codabar data redundant check=3 End Of Configuration
USER’S MANUAL Handy Wireless Scanner 46 Start Of Configuration Code 39 Parameter Setting Barcode Value Barcode Label Description RC01 Code 39 enable RD01 Code 39 disable RC13 Code 32 enable RD13 Code 32 disable DC00 Code 39 data redundant check=off DC01 Code 39 data redundant check=1 DC02 Code 39 data redundant check=2 DC03 Code 39 data redundant check=3 3901 Standard code 39 3902 Full ASCII code 39 3903 Code 39 start/stop character transmission 3904 Code 39 start/stop character without transmission End Of Configuration
USER’S MANUAL Handy Wireless Scanner 47 Start Of Configuration Barcode Value Barcode Label Description 3905 Code 39 check digit calculate and transmit 3906 Code 39 check digit calculate but without transmit 3907 No check character 3908 Code 39 maximum length setting 3909 Code 39 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 3912 Code 32 (Italian pharmacy) transmit “A” character 3913 Code 32 (Italian pharmacy) without transmit ”A” character End Of Configuration
USER’S MANUAL Handy Wireless Scanner 48 Start Of Configuration Code 93 Parameter Setting Barcode Value Barcode Label Description RC08 Code 93 enable RD08 Code 93 disable DC30 Code 93 data redundant check=off DC31 Code 93 data redundant check=1 DC32 Code 93 data redundant check=2 DC33 Code 93 data redundant check=3 9301 Code 93 maximum length setting 9302 Code 93 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 9303 Code 93 check digit calculate but without transmit 9304 Code 93 check digit not calculate and without transmit 9305 Code 93 check digit calculate and transmit End Of Configuration
USER’S MANUAL Handy Wireless Scanner 49 Start Of Configuration Code 128 Parameter Setting Barcode Value Barcode Label Description RC06 Code 128 enable RD06 Code 128 disable RC10 EAN-128 enable RD10 EAN-128 disable DC40 Code 128 data redundant check=off DC41 Code 128 data redundant check=1 DC42 Code 128 data redundant check=2 DC43 Code 128 data redundant check=3 1803 No check character 1804 Calculate but not transmit 1805 Calculate and transmit 1806 Code 128 maximum length setting 1807 Code 128 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 50 Start Of Configuration Chinese Post Code Parameter Setting Barcode Value Barcode Label Description RC05 Chinese post code enable RD05 Chinese post code disable DC60 Chinese post code data redundant check=off DC61 Chinese post code data redundant check=1 DC62 Chinese post code data redundant check=2 DC63 Chinese post code data redundant check=3 SZ01 Chinese post code maximum length setting SZ02 Chinese post code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 51 Start Of Configuration MSI/Plessy Parameter Setting Barcode Value Barcode Label Description RC14 MSI enable RD14 MSI disable DC70 MSI data redundant check= off DC71 MSI data redundant check=1 DC72 MSI data redundant check=2 DC73 MSI data redundant check=3 MS01 MSI/Plessy maximum length setting MS02 MSI/Plessy minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) MS03 MSI/Plessy double check digit calculate but not transmit MS04 MSI/Plessy double check digit without calculate and transmit MS05 MSI/Plessy double check digit calculate but only first digit transmit MS06 MSI/Plessy double check digit calculate and both transmit MS07 MSI/Plessy single check digit calculate but without transmit MS08 MSI/Plessy single check digit calculate and transmit End Of Configuration
USER’S MANUAL Handy Wireless Scanner 52 Start Of Configuration Code 11 Interface Setting Barcode Value Barcode Label Description RC07 Code 11 enable RD07 Code 11 disable 1101 Code 11 maximum length setting 1102 Code 11 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) 1103 Code 11 one check digit verification 1104 Code 11 two check digit verification 1105 Two Check for Code 11 check digit if code length is longer than 10 characters 1106 Disable verification 1107 Code 11 check digit transmitted 1108 Code 11 check digit not transmitted End Of Configuration
USER’S MANUAL Handy Wireless Scanner 53 Start Of Configuration ITF 2 of 5 Parameter Setting Barcode Value Barcode Label Description RC04 ITF 2 of 5 enable RD04 ITF 2 of 5 disable RC09 IATA code enable RD09 IATA disable DC80 ITF 25 data redundant check=off DC81 ITF25 data redundant check=1 DC82 ITF25 data redundant check=2 DC83 ITF25 data redundant check=3 IT03 ITF 2 of 5 no check character IT04 ITF 2 of 5 check digit calculate and transmit IT05 ITF 2 of 5 check digit calculate but without transmit End Of Configuration
USER’S MANUAL Handy Wireless Scanner 54 Start Of Configuration Barcode Value Barcode Label Description IT01 ITF 2 of 5 code maximum length setting IT02 ITF 2 of 5 code minimum length setting IT06 ITF 2 of 5 one fixed length setting IT07 ITF 2 of 5 two fixed length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) IT08 ITF 2 of 5 length variable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 55 Start Of Configuration Standard 2 of 5 Parameter Setting Barcode Value Barcode Label Description RC22 Standard 2 of 5 code enable RD22 Standard 2 of 5 code disable D051 Standard 2 of 5 code maximum length setting D052 Standard 2 of 5 code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D053 Standard 2 of 5 code no check character D054 Standard 2 of 5 code check digit calculate and transmit D055 Standard 2 of 5 code check digit calculate but without transmit End Of Configuration
USER’S MANUAL Handy Wireless Scanner 56 Start Of Configuration Industrial 2 of 5 Parameter Setting Barcode Value Barcode Label Description RC21 Industrial 2 of 5 code enable RD21 Industrial 2 of 5 code disable D251 Industrial 2 of 5 code maximum length setting D252 Industrial 2 of 5 code minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D253 Industrial 2 of 5 code no check character D254 Industrial 2 of 5 code check digit calculate and transmit D255 Industrial 2 of 5 code check digit calculate but without transmission End Of Configuration
USER’S MANUAL Handy Wireless Scanner 57 Start Of Configuration UPC/EAN/JAN Parameter Setting Barcode Value Barcode Label Description RC11 EAN convert to ISSN/ISBN enable RD11 EAN convert to ISSN/ISBN disable RC03 UPC/EAN/JAN enable RD03 UPC/EAN/JAN disable UE01 UPC/EAN/JAN all enable UE02 EAN-8 or EAN-13 enable UE03 UPC-A and EAN-13 enable UE04 UPC-A and UPC-E enable UE05 UPC-A enable UE06 UPC-E enable UE07 EAN-13 enable UE08 EAN-8 enable UE09 UPC/EAN Addendum disable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 58 Start Of Configuration Barcode Value Barcode Label Description UE10 Add on 5 only UE11 Add on 2 only UE12 Add on 2 or 5 UE13 Force UPC-E to UPC-A format enable UE14 Force UPC-E to UPC-A format disable UE15 Force UPC-A to EAN-13 format enable UE16 Force UPC-A to EAN-13 format disable UE44 Force EAN-8 to EAN-13 format enable UE45 Force EAN-8 to EAN-13 format disable UE17 Transmit UPC-A check digit enable UE18 Transmit UPC-A check digit disable UE19 Transmit UPC-E leading character enable UE20 Transmit UPC-E leading character disable UE21 Transmit UPC-E check digit enable UE22 Transmit UPC-E check digit disable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 59 Start Of Configuration Barcode Value Barcode Label Description UE23 Transmit EAN-8 check digit enable UE24 Transmit EAN-8 check digit disable UE25 Transmit EAN-13 check digit enable UE26 Transmit EAN-13 check digit disable UE27 Transmit UPC-A leading character enable UE28 Transmit UPC-A leading character disable UE30 Add-on format with separator UE31 Add-on format without separator UE60 EAN-13 country code first “0” can be transmitted UE61 EAN-13 country code first:”0” can’t be transmitted UE66 EAN-13 with first 0 ID code same as “UPC-A” UE67 EAN-13 with first 0 ID code same as “EAN-13” DC10 UPC-A data redundant check=off DC11 UPC-A data redundant check=1 End Of Configuration
USER’S MANUAL Handy Wireless Scanner 60 Start Of Configuration Barcode Value Barcode Label Description DC12 UPC-A data redundant check=2 DC13 UPC-A data redundant check=3 DC14 UPC-E data redundant check=off DC15 UPC-E data redundant check=1 DC16 UPC-E data redundant check=2 DC17 UPC-E data redundant check=3 DC20 EAN-13 data redundant check=off DC21 EAN-13 data redundant check=1 DC22 EAN-13 data redundant check=2 DC23 EAN-13 data redundant check=3 DC24 EAN-8 data redundant check=off DC25 EAN-8 data redundant check=1 DC26 EAN-8 data redundant check=2 DC27 EAN-8 data redundant check=3 UE32 EAN/UPC +add-on (none mandatory) UE33 EAN/UPC +add-on (mandatory) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 61 Start Of Configuration UE35 EAN/UPC +add-on mandatory for 978/977 bookland (Supplement requirement, not sent for other) UE38 EAN/UPC +addon mandatory for 978/977 bookland (Supplement requirement, optional for other) UE42 EAN/UPC +addon mandatory for 491 Japanese bookland (Supplement requirement, not sent for other) UE43 EAN/UPC +addon mandatory 491 Japanese bookland (Supplement requirement, optional for other) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 62 Start Of Configuration Telepen Parameter Setting Barcode Value Barcode Label Description RC25 Telepen enable RD25 Telepen disable TE03 Telepen numeric mode enable TE04 AIM Telepen enable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 63 Start Of Configuration Matrix 2 of 5 Parameter Setting Barcode Value Barcode Label Description RC12 Matrix 2 of 5 enable RD12 Matrix 2 of 5 disable D151 Matrix 2 of 5 maximum length setting D152 Matrix 2 of 5 minimum length setting SET Confirm to save this setting (required for reading full ASCII table and length setting) D153 Matrix 2 of 5 no check character D154 Matrix 2 of 5 check digit calculate and transmit D155 Matrix 2 of 5 check digit calculate but without transmission End Of Configuration
USER’S MANUAL Handy Wireless Scanner 64 Start Of Configuration GS1 DataBar Parameter Setting There are 7 kinds of barcodes in the GS1 DataBar family and they are categorized into three groups. Barcode types in the same group use the same barcodes for setting. Group Representative Contents Group 1 GS1 DataBar Omnidirectional (Formally RSS-14) GS1 DataBar Omnidirectional GS1 DataBar Truncated GS1 DataBar Stacked GS1 DataBar Stacked Omnidirectional Group 2 GS1 DataBar Limited (Formally RSS Limited) GS1 DataBar Limited Group 3 GS1 DataBar Expanded (Formally RSS Expanded) GS1 DataBar Expanded GS1 DataBar Expanded Stacked GS1 DataBar Omnidirectional (Formally RSS-14) Barcode Value Barcode Label Description RC15 GS1 DataBar Omnidirectional enable RD15 GS1 DataBar Omnidirectional disable SS00 Transmit GS1 DataBar Omnidirectional check digit SS01 Do not transmit GS1 DataBar Omnidirectional check digit SS02 Transmit GS1 DataBar Omnidirectional application ID (01) SS03 Do not transmit GS1 DataBar Omnidirectional application ID (01) SS05 GS1 DataBar Omnidirectional /EAN-128 emulation enable SS04 GS1 DataBar Omnidirectional /EAN-128 emulation disable End Of Configuration
USER’S MANUAL Handy Wireless Scanner 65 Start Of Configuration GS1 DataBar Limited (Formally RSS Limited) Barcode Value Barcode Label Description RC16 GS1 DataBar Limited enable RD16 GS1 DataBar Limited disable SS10 Transmit GS1 DataBar Limited check digit SS11 Don’t transmit GS1 DataBar Limited check digit SS12 Transmit GS1 DataBar limited application ID (01) SS13 Do not transmit GS1 DataBar limited application ID End Of Configuration
USER’S MANUAL Handy Wireless Scanner 66 Start Of Configuration GS1 DataBar Expanded (Formally RSS Expanded) Barcode Value Barcode Label Description RC17 GS1 DataBar Expanded enable RD17 GS1 DataBar Expanded disable SS07 GS1 DataBar Expanded/EAN-128 emulation enable SS06 GS1 DataBar Expanded/EAN-128 emulation disable SS08 GS1 DataBar Expanded check digital enable SS09 GS1 DataBar Expanded check digital disable SS16 Transmit GS1 DataBar Expanded application ID (01) SS17 Do not transmit GS1 DataBar Expanded application ID End Of Configuration
USER’S MANUAL Handy Wireless Scanner 67 Start Of Configuration Data Editing Identifier Code Barcode Value Barcode Label Description IS00 Disable identifier code IS01 Enable identifier code table as factory standard IS03 Enable identifier code table as AIM standard. CI01 Code 39 identifier code setting CI02 ITF 2 of 5 identifier code setting CI03 Chinese Post Code identifier code setting CI04 UPC-E identifier code setting CI05 UPC-A identifier code setting CI06 EAN-13 identifier code setting CI07 EAN-8 identifier code setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 68 Start Of Configuration Barcode Value Barcode Label Description CI08 Codabar identifier code setting CI09 Code 128 identifier code setting CI10 Code 93 identifier code setting CI11 MSI identifier code setting CI12 GS1 DataBar Omnidirectional identifier code setting CI13 GS1 DataBar Limited identifier code setting CI14 GS1 DataBar expanded identifier code setting CI15 Industrial 2 of 5 identifier code setting CI16 Code 11 Identifier code setting CI17 Standard 2 of 5 identifier code setting CI18 Matrix 2 of 5 identifier code setting SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 69 Start Of Configuration Header and Trailer Barcode Value Barcode Label Description CP11 Add code length as header enable (2 digits) CP12 Add code length as header disable (2 digits) HT01 Header (Preamble) HT02 Trailer (Postamble) HT03 Truncate header character HT04 Truncate trailer character SET Confirm to save this setting (required for reading full ASCII table and length setting) End Of Configuration
USER’S MANUAL Handy Wireless Scanner 70 Start Of Configuration Full ASCII Code 39 Table Code 39 ASCII Hexa-codeCode 39 ASCII Hexa-code Full ASCII ---NUL 00 Full ASCII ---SI Function key-----“Shift”0F Full ASCII ---SOH Function key-----“Ins” 01 Full ASCII ---DLE Function key-----“5(num)” 10 Full ASCII ---STX Function key-----“Del” 02 Full ASCII ---DC1 Function key-----“F1” 11 Full ASCII ---ETX Function key-----“Home” 03 Full ASCII ---DC2 Function key-----“F2” 12 Full ASCII ---EOT Function key-----“End” 04 Full ASCII ---DC3 Function key-----“F3” 13 Full ASCII ---ENQ Function key-----“Up arrow” 05 Full ASCII ---DC4 Function key-----“F4” 14 Full ASCII ---ACK Function key-----“Down arrow” 06 Full ASCII ---NAK Function key-----“F5” 15 Full ASCII ---BEL Function key-----“Left arrow” 07 Full ASCII ---SYN Function key-----“F6” 16 Full ASCII ---BS Function key-----“Backspace” 08 Full ASCII ---ETB Function key-----“F7” 17 Full ASCII ---HT Function key-----“TAB” 09 Full ASCII ---CAN Function key-----“F8” 18 Full ASCII ---LF Function key-----“Enter (alpha numeric)” 0A Full ASCII ---EN Function key-----“F9” 19 Full ASCII ---VT Function key-----“right arrow” 0B Full ASCII ---SUB Function key-----“F10” 1A Full ASCII ---FF Function key-----“PgUp” 0C Full ASCII ---ESC Function key-----“F11” 1B Full ASCII ---CR Function key-----“Enetr(num.)” 0D Full ASCII ---FS Function key-----“F12” 1C Full ASCII ---SO Function key-----“PgDn” 0E Full ASCII ---GS Function key-----“ESC” 1D End Of Configuration
USER’S MANUAL Handy Wireless Scanner 71 Start Of Configuration Full ASCII Code 39 Table (continued) Code 39 ASCII Hexa-code Code 39 ASCII Hexa-code Full ASCII ---RS Function key-----“CTL(L)” 1E Full ASCII ---- 2D Full ASCII ---US Function key-----“ALT(L)” 1F Full ASCII ---. 2E Full ASCII ---SP 20 Full ASCII ---/ 2F Full ASCII ---! 21 Full ASCII ---0 30 Full ASCII ---“ 22 Full ASCII ---1 31 Full ASCII ---# 23 Full ASCII ---2 32 Full ASCII ---$ 24 Full ASCII ---3 33 Full ASCII ---% 25 Full ASCII ---4 34 Full ASCII ---& 26 Full ASCII ---5 35 Full ASCII ---‘ 27 Full ASCII ---6 36 Full ASCII --- ( 28 Full ASCII ---7 37 Full ASCII ---) 29 Full ASCII ---8 38 Full ASCII ---* 2A Full ASCII ---9 39 Full ASCII ---+ 2B Full ASCII ---: 3A Full ASCII ---, 2C Full ASCII ---; 3B End Of Configuration
USER’S MANUAL Handy Wireless Scanner 72 Start Of Configuration Full ASCII Code 39 Table (continued) Code 39 ASCII Hexa-code Code 39 ASCII Hexa-code Full ASCII ---< 3C Full ASCII ---K 4B Full ASCII ---= 3D Full ASCII ---L 4C Full ASCII ---> 3E Full ASCII ---M 4D Full ASCII ---? 3F Full ASCII ---N 4E Full ASCII ---@ 40 Full ASCII ---O 4F Full ASCII ---A 41 Full ASCII ---P 50 Full ASCII ---B 42 Full ASCII ---Q 51 Full ASCII ---C 43 Full ASCII ---R 52 Full ASCII ---D 44 Full ASCII ---S 53 Full ASCII ---E 45 Full ASCII ---T 54 Full ASCII ---F 46 Full ASCII ---U 55 Full ASCII ---G 47 Full ASCII ---V 56 Full ASCII ---H 48 Full ASCII ---W 57 Full ASCII ---I 49 Full ASCII ---X 58 Full ASCII ---J 4A Full ASCII ---Y 59 End Of Configuration
USER’S MANUAL Handy Wireless Scanner 73 Start Of Configuration Full ASCII Code 39 Table (continued) Code 39 ASCII Hexa-code Code 39 ASCII Hexa-code Full ASCII ---Z 5A Full ASCII ---i 69 Full ASCII ---[ 5B Full ASCII ---j 6A Full ASCII ---\ 5C Full ASCII ---k 6B Full ASCII ---] 5D Full ASCII ---l 6C Full ASCII ---^ 5E Full ASCII ---m 6D Full ASCII ---_ 5F Full ASCII ---n 6E Full ASCII ---` 60 Full ASCII ---o 6F Full ASCII ---a 61 Full ASCII ---p 70 Full ASCII ---b 62 Full ASCII ---q 71 Full ASCII ---c 63 Full ASCII ---r 72 Full ASCII ---d 64 Full ASCII ---s 73 Full ASCII ---e 65 Full ASCII ---t 74 Full ASCII ---f 66 Full ASCII ---u 75 Full ASCII ---g 67 Full ASCII ---v 76 Full ASCII ---h 68 Full ASCII ---w 77 End Of Configuration
USER’S MANUAL Handy Wireless Scanner 74 Start Of Configuration Full ASCII Code 39 Table (continued) Code 39 ASCII Hexa-code Code 39 ASCII Hexa-code Full ASCII ---x 78 Full ASCII ---| 7C Full ASCII ---y 79 Full ASCII ---} 7D Full ASCII ---z 7A Full ASCII ---~ 7E Full ASCII ---{ 7B Full ASCII ---DEL 7F End Of Configuration
Handy Wireless Scanner 75 USER’S MANUALAppendix 1: USB Virtual COM Driver Installation Contact your distributor to get the driver and follow the steps below to enable USB virtual COM port. 1. Connect the handheld scanner and the host (e.g. a PC) with a USB interface cable. 2. Enable USB virtual COM port with programming barcode on page 32. 3. After the programming, the host would request driver installation. Browse your files to locate the driver and start installation. 4. The USB virtual COM port is ready for use after driver installation.
USER’S MANUAL Handy Wireless Scanner 76 Appendix 2: Barcode Length Setting Introduction The length of a barcode is the number of characters it contains, including check digits. As listed in the Default Parameters section, each barcode type has different default length. You may change the setting by the following procedure. To set up barcode length, the paramours to be determined are barcode type and the desired barcode length. Barcode length is consisted of 2 digits. For numbers smaller than 10, you need to add a “0” in the front. Example If the barcode length is 4 to 12 digits, the steps would be as below: EndSet up barcode length Start Set up minimum barcode length Start of Configuration Set up maximum barcode length End of Configuration Scan the “Start of configuration” barcode Scan the “Min“ barcode Set the “Max” barcode Scan the “Set” barcode to save this settingSet up the second digit: 2 Scan the “End of configuration” barcodeScan the first digit: 0 Scan the second digit: 4 Turn to the page of the barcode type to be set up Read the “Full ASCII code 39” barcode Set up the first digit: 1 Use the ASCII table (Appendix 4) to set up barcode length. Be sure to enable the full ASCII code 39 option before you start and read the “Set” label to set your choice into memory.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: zReorient or relocate the receiving antenna. zIncrease the separation between the equipment and receiver. zConnect the equipment into an outlet on a circuit different from that to which the receiver is connected. zConsult the dealer or an experienced radio/TV technician for help. 15.21FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 15.19This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

Navigation menu