Bendix Commercial Vehicle Systems TX433TV-2 433.92 MHz Valve Transmitter User Manual Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	572346
Application ID	wPma7lX9OFBLyixCP9wqmQ==
Document Description	Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	45.06kB (563265 bits)
Date Submitted	2005-08-17 00:00:00
Date Available	2005-08-17 00:00:00
Creation Date	2005-08-12 12:05:54
Document Lastmod	0000-00-00 00:00:00
Document Title	Installation Guide

PREPARATION
The wheel must be 15" or larger to use valve
mount transmitters (Fig.1). Otherwise strap mount
transmitters (Fig.2) should be installed.
ngj Valve mount
Remove the plastic colored vmshers from ”3"me
the installation kit and match these with
the corresponding color-ceded transmitter.
Remove the tire from the wheel. ' v
we scrap mount
vansmflter
Discard the existing valve.
Find the new valve Included with the SmarTire kit and clean
the valve hole with a clean cloth. Determine if the outside
inner surface of the valve hole has a rounded or flat surface.
A rounded surface requires the beveled washer (See Figs).
SMARTIRE VALVE TRANSMITTER PARTS
Valve Transmittal
Attammem /
screw
211.1 H
Coloured washer/ Dust up
—Mjustment pin
TOOLS REQUIRED
Tools required to install valve mount transmitters:
' TZD TORX bit
' 11 mm Socket
- Torque wrench
- Adjustment pin (provided with valve set)
VALVE INSTALLATION GUIDELINES
1. Fit the transmitter’s circular face to the round valve
stemhead and hand tighten the attachment screw two turns.
Insert the valve stem Into the wheel valve hole with the
appropriate washer (flat or beveled). Hand tighten the valve
anchor nut. The valve adjustment hole must be visible on
top. (See Fig.4)
Note: The attachment screw can only be used once due to the
thiead-Iocldng adhesive.
2. Confirm that the valve transmitter will fit on this particular
wheel. Pivot the transmitter, checking that both contact pads
rest in the drop centre well of the wheel and that there
is a gap at the top of at least the thickness of the adjustment
pin (See Fig.4). If the transmitter cannot be made to sit
flat the SmarTire strap mount transmitter must be used
instead (See Fig.5). .
FM - Nu m -
use stmp Mount
transmitters
3. Use the 11 mm socket and torque wrench to tighten the
valve anchor nut to 35.4 Ibt.in (+I-.44) or 4 NM (+I-.05).
Use the valve adjustment pin to ensure the valve stem
does not turn while tightening. (See Figs)
4. Hold the transmitter so that it sits flat in the drop centre well
at the wheel. Use the T20 TORX bit and torque wrench to
tighten the transmitter attachment screw to 31 Ibfin (tl- AA)
or 35 NM (+/- 05). Use the valve adjustment pin to ensure
the valve stem does not turn while tightening. Thread the
corresponding colored washer on the valve stem to match
the colored dot on the transmitter. Screw the dust cap on the
valve. (See Fig.7)
m TORX DII
Coloured wattle
n .
M5 \DIIDIND
Fig. 7
MOUNT THE TIRE ONTO WHEEL
5. When mounting the tire, avoid damaging the transmitter by
positioning me wheel with the transmitter located 90’ in
front of the bead guiding shoe. The wheel is set to rotate
clockwise. (See Fig.8)
sand guiding shoe
van. and Transmitter Fi'g.8
6. Set the lubricated tire on the wheel with its traction point
3" (8 cm) before the transmitter. Use the bead guiding shoe
m guide the rest 01 the bottom bead over the flange and
onto the rim. See Fig.8.
Note: If the tire slips several inches on the wheel dun'ng the
installation process, stop and reposition the transmitter/wheel
back to 90' in front of bead guiding shoe.
7. With the bottom head in place, again position the wheel
with the transmitter located 90‘ in tront oi the bead guiding
shoe. Depress the head into the drop centre so that the
traction point is 3" (8 cm) betore the transmitter. Use the
bead guiding shoe to guide the rest of the top bead over
the flange and onto the rim.
Note: If thel tine slips several inches on the wheel during the
installation process, stop and reposition the transmitter/wheel
back to 90' in front of bead guiding shoe.
8. Innate the tire to seat the bead, deflate completely and
then inflate the tire to manufacturer’s recommended cold
inflation pressure.
9. Balance the wheel.
10. lnstatthetiresorithevehtcleawoidingtottiedeieultootor-ooded
positions (See Figs).
Gleen-rightiiont Blue-While"
Red - tell horn Yellow - Ielt mar Flg.9
® swimfll'ine
Smar‘l'ire Systems Inc.
150 - 13151 Vanier Place
Richmond, British Columbia
Canada
VGV 2J1
T: 604 276 9884
info@smartire.com
www.smart|re.com
DE-MOUNTING THE TIRE WITH
TRANSMITTER INSTALLED
1. Remove the tire/wheel assembly from vehicle and deflate
completely. Orient the wheel to place the transmitter 180'
from the pressure shoe tor unseating both the top and bottom
beads so that the pressure shoe or tire bead will not
damage the transmitter. (See Fig.1o)
Preemie shoe
FIg,1lJ
2. When lilting the top bead over the rimflange, orient the wheel
to place the transmitter at the center of the bead guiding
shoe. Remove the top bead. Orient the wheel once more with
the transmitter at the center the center of the bead-guiding
shoe and remove the bottom bead. The uansmitter should
be checked tor correct positioning and fit prior to tire
replacement. (See Fig,11)
Valve and Tmnmiilter
Bead oulolnsi shoe
Mounfing bar
rmoilon mini
~ Fl'g.11
NORTH AMERICAN WARRANTY
This Warranty covers substantial manufacturer's defects in workmanship
and maiarials. it does not cover any unit mat is damaged beyond nonnai
usage. was not mostly installed, was subjected to chemlcal contact, or
other acts or omissions not sanctioned by the Owner's Manual.
All components are covered for one (1) year and unlimited mileage following
the date of purchase.
The Smer‘l'ire Wan-aniy will be honored oy any authorized SmarTlre dealer.
The owner is required lo provide dated ptoololpurchase. The authorized
dealer will determine it there is e vrarrxnteble condition assocmitett wtm
materials and/or manutacturing womnanstiip. ii a warranlable condition
exists, the eomponeni will be replaced tree of eharge. shipping prepaid, it
within the applicable wananiy period. The owner is responsible tor any
labor and installation charges.
Telephone 604-276-9884 lo obtain a Return Material Authorization (RMA)
number and address details to send the postage prepaid Wage with the
detective unit and RMA number.
The warranty does not include any further obligation whatsoever.
including but not limited to actual installalion ol the replacement unit on
the customer's vehicle.
FURTHER WARRANTV INFORMATION SPECIFIC T0 CANADA AND
THE U.S. CAN BE FOUND IN THE SMARTIRE OWNER'S MANUAL

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Author                          : 
Creator                         : 
Producer                        : 
Title                           : 
Subject                         : 
Create Date                     : 2005:08:12 12:05:54

EXIF Metadata provided by EXIF.tools