Bendix Sd 06 1600 Users Manual 1600f Updated Caution Note And TMs Only

2015-04-02

: Bendix Bendix-Sd-06-1600-Users-Manual-682553 bendix-sd-06-1600-users-manual-682553 bendix pdf

Open the PDF directly: View PDF PDF.
Page Count: 4

DownloadBendix Bendix-Sd-06-1600-Users-Manual- Sd-06-1600f Updated Caution Note And TMs Only Bendix-sd-06-1600-users-manual
Open PDF In BrowserView PDF
SD-06-1600
Bendix® LP-2™ & LP-3™ Low Pressure Indicators

COVER

DIAPHRAGM

COVER
SPRING
CONTACT
POINTS

SPRING
CONTACT
POINTS
PISTON

BODY

BODY
O-RING
DIAPHRAGM

FIGURE 1 - BENDIX® LP-2™ LOW PRESSURE INDICATOR

FIGURE 2 - BENDIX® LP-3™ LOW PRESSURE INDICATOR

DESCRIPTION

employs a spring loaded o-ring diaphragm and piston. The
LP-3™ indicator is available with either one terminal or two.
The single terminal unit utilizes a metallic gasket between
body and case to ground the lower contact strip. The two
terminal unit utilizes a phenolic insulating gasket to isolate
both terminals from the vehicle frame.

The low pressure indicator is a safety device designed
to give an automatic warning to the driver whenever air
pressure in the air brake system is below the safe minimum
for normal vehicle operation. It is usually used to operate
an electrical buzzer or warning light, or both, which are
audible or visible to the driver.
Two styles of low pressure indicators are currently
manufactured.
The Bendix® LP-2™ low pressure indicator, which is the
older style, consists of a die cast body with a spring loaded
diaphragm clamped between the body and the Bakelite
cover.
The Bendix® LP-3™ low pressure indicator is the newer
style. It consists of a die cast body, nylon cover and

The electrical contacts provided in both the LP-2™ and
LP-3™ indicators remain closed by spring force until the
air brake system pressure below the diaphragm is above
the setting (force) of the low pressure indicator spring. The
setting of the indicator and piece number is marked on a
label on the valve body. If a label is not present, then the
vehicle manual should be consulted for the proper setting.
The nominal setting of the indicator is 60 psi; however,
pressure settings may vary depending upon the vehicle.

1

OPERATION
To describe the operation, we shall assume that the low
pressure indicator is set for 60 psi. When air pressure at the
supply port and under the diaphragm is above 60 psi, the
electrical contacts remain open because the force exerted
by air pressure underneath the diaphragm overcomes the
force exerted by the spring above the diaphragm.

4. Disconnect the electrical connections at the low
pressure indicator.
5. Disconnect the air line and mounting bolts or unscrew
the Indicator from the fitting and remove.

INSTALLING
1. Install in a convenient location for servicing.

When air pressure below the diaphragm drops below 60
psi, the spring exerts a force which is greater than the
force exerted by the air pressure below the diaphragm.
This causes the diaphragm (and the piston in the Bendix®
LP-3™ indicator) to move and allow the electrical contacts
to close. This completes or closes the electrical circuit to
the warning device, warning the driver of low air pressure
in the system.

2. Connect to a reservoir pressure line at a high point in
the system for adequate drainage.

PREVENTIVE MAINTENANCE

NOTE: It is generally recommended that the low pressure
indicator, if faulty, be replaced with a new unit;
however, service parts are available; and if repairs
are necessary, the following will apply:

Important: Review the Bendix Warranty Policy before
performing any intrusive maintenance procedures. A
warranty may be voided if intrusive maintenance is
performed during the warranty period.
No two vehicles operate under identical conditions; as
a result, maintenance intervals may vary. Experience is
a valuable guide in determining the best maintenance
interval for air brake system components. At a minimum,
the low pressure indicator should be inspected every 6
months or 1500 operating hours, whichever comes first,
for proper operation. Should the low pressure indicator not
meet the elements of the operational tests noted in this
document, further investigation and service of the valve
may be required.

TESTING FOR SERVICEABILITY
OPERATING TEST
1. If possible, determine the setting of the low pressure
indicator by referring to the label on the valve or the
vehicle manual.
2. Operation of the low pressure indicator may be checked
with ignition switch “on” by reducing the system
pressure and observing that low pressure warning
occurs when system pressure drops below the setting
of the low pressure indicator. The contacts will be
closed when the warning device operates. If the setting
of the indicator is unknown, the contacts should close
between approximately 70 psi and 50 psi.
LEAKAGE TEST
1. With air pressure present at the supply port, coat the
indicator with a soap solution. No leakage is permitted.

REMOVING
1. Block the wheels or secure the vehicle with other than
service brakes.
2. The ignition switch should be in the “off” position.
3. Drain the air from the system.
2

3. If installing a Bendix® LP-2™ indicator, use a supply line
of 1/4” O.D. minimum.
4. Connect the Indicator terminals in series with the
ignition switch and the warning device.

DISASSEMBLY

LP-2™ indicator. Unscrew the cover retainer from the
body. Remove cover and remove spring and diaphragm
assembly.
LP-3™ indicator. Remove cover screw and lockwashers.
Remove the cover, contact disc, spring, and shim(s). (Note:
shims may or may not be present.) Remove contact plate,
gasket, piston, and o-ring diaphragm.

CLEANING AND INSPECTION
1. Clean all metal parts in mineral spirits and dry them
completely.
2. Inspect all parts for excessive wear or deterioration.
Check the valve spring for cracks or corrosion.
3. Inspect contact points. If contact points are not severely
pitted, they can be dressed with a fine file.
Replace all parts that were discarded and any parts not
found to be serviceable during inspection, using only
genuine Bendix replacement parts.

ASSEMBLY
NOTE: When using pipe thread sealant during assembly
and installation, take particular care to prevent the
sealant from entering the valve itself. Apply the
sealant beginning with the second thread back
from the end.
BENDIX® LP-2™ INDICATOR
1. Place and position the diaphragm assembly in the
body. Position the spring so that it rests on the upper
diaphragm follower.
2. Place the cover over the diaphragm and screw the
cover retainer to the body and tighten securely. (Torque
to 110-130 inch pounds.)

BENDIX® LP-3™ INDICATOR

6. If shim(s) are used, place shim(s) in cover.

1. Lubricate the bore of the body and both sides of the
o-ring diaphragm with silicone lubricant BW-650-M
(Bendix piece no. 291126).

7. Place the spring in the cover.

2. Install the o-ring diaphragm in the body. (Note: the o-ring
portion of diaphragm should face the supply port.)
3. Install the piston in the body. The flat side of the piston
should face the o-ring diaphragm.
4. Install the gasket. (Always use a phenolic gasket in a
two terminal switch and a metallic gasket in the single
terminal switch.)
5. Position the contact plate over the fingers of the piston.
The contact plate should rest on the face of the gasket.

8. Place the contact point so that it rests on the spring.
9. Install the cover on the body using the machine screws.
Make certain that the contact plate is in position over
the fingers of the piston and the arm of the contact plate
is positioned so that it will fit in the groove of the cover.
10. Tighten the screws securely. (Torque to 20-30 inch
pounds).

TEST OF REBUILT LOW PRESSURE INDICATOR
After rebuilding, perform the leakage and operating tests as
outlined in the section entitled “Testing for Serviceability.”

3

4

BW1447 © 2011 Bendix Commercial Vehicle Systems LLC All rights reserved. 6/2011 Printed in U.S.A.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : e006183
Create Date                     : 2011:06:13 10:21:24-04:00
Modify Date                     : 2011:06:13 10:21:24-04:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.4.2 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : sd-06-1600f updated caution note and TMs only.indd
Creator                         : e006183
Document ID                     : uuid:02bbbdf0-93be-4b13-9ffb-8aed8064bebc
Instance ID                     : uuid:41620f0a-49d7-420f-b381-02086be174a9
Page Count                      : 4
EXIF Metadata provided by EXIF.tools

Navigation menu