Betterway Electronic SH-321 PORTABLE WIRELESS PA AMPLIFIER User Manual C8ABD2B3B4ABD5E6CDBCC6AC
Betterway Electronic Co., Ltd. PORTABLE WIRELESS PA AMPLIFIER C8ABD2B3B4ABD5E6CDBCC6AC
USERS MANUAL
RECHARGEABLE PORTABLE WIRELESS PA SYSTEM Hisonic “3-321 Please read this first: 1. Before using this wireless microphone, please ensure that you read and understand the safety precautions below. Always ensure that the wireless PA System/microphone and receiver are operated correctly. 2. The safety precautions noted on the following pages are intended to instruct you in the safe and correct operation of the system to prevent injuries or dame to yourself, other persons and the equipment. 3. If you have any questions, please do not send the system back to the dealer where you bought (Unless you bought extended service), call the number 1-866 524 8676 for service before you send them back to Hisonic International Inc. 4. If you have a problem with the reception, it might not be the system’s fault,you might have a local interference on the frequency which this system uses, so you can ask for an exchange for another frequency to replace the one in your hand to solve this problem, or upgrade to a 16 -channel system to resolve the problem. 5. In the next few pages, the term “system" refers primarily to the handheld microphone and it‘s receiver ( Amplifier Speaker ), including the other accessories. The HS-321 is a rechargeable and AC powered public address system amplifier / speaker with a built in VHF wireless microphone receiver. This heavy duty 50W(Max) PA system is built inside a strong aluminum case to give you loud and clear sound. It is excellent for classrooms, show events, auctions, seminars, church use, indoor/outdoor functions. FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED - BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS - COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Table of Contents 1.Packing list ............. ...... ....P2 2. Basic Operation. ..P5 3. Specifications ......... .. ..P8 4. Troubleshooting ..................................................................... P9 1. Packing List: ljl all © © 1. PA Speaker 2. Wireless Handheld microphone 3. Wireless Belt pack transmitter 4. Lapel Microphone 5. Headset Microphone 6. Manual Book © 7. Power Cord 8. 9V battery 9. Back pack bag 0. Car cigaretter lighter cable 2. Components Guide A.PA Amplifier( Wireless microphone receiver) DCiZV/ZAPGMSI .Jad( (0mm ®ACLE)(ACPovva) ©cragigifleau 2. coooxlmgnppo 0 TAPE/AUX Volume - a WIRELESS 2 Voiume -® WIRELESS 1 Volume ©Bridge 9 Power M cnag'ngsmm ®Antenna 0 pm, / o M; F: ®Auxlliary audio outpul — gmmieim ammzmn ©Ama’ha’ysmiolnpm . Power indicator To show the Power is on or not. Ac indicator, connect the power cord to power souce, switch to “NO" or "CHARGE" position, the AC LED lights up, switch to "OFF" posstion, the AC LED goes off. Charging indicator Shows the system is in charging. DC Fuse Protection from DC overload. Power Switch .To turn on/off the main power. . Power Jack. . AC Fuse Protection from AC overload. . DC 12V/2A power Jack. . Bridge Connect to another PA system. 10. Antenna For a better reception. Extended antenna. 1 . Auxiliary audio output. Output to any other compatible devices. 12. Auxiliary audio input. Input from other sound sources. 13. Microphone 1 input. Connect optional microphone system. 14. Microphone 2 input. Connect a secondary optional microphone system. 15. Tone control Control the tone of the speaker. 16. Wireless Mic Volume To control the wireless microphone volume for the built in receiver. 17. AUX Volume To control the auxiliary input volume. 18. Microphone 1 volume control for an optional microphone system. 19. Microphone 2 volume control for a secondary microphone system (The optional microphones are not included.) B.Handheld Microphone a) MIC av Battery ® Indicator ®Swi|ch ®Beltery 5) compartment cover compartment Close Open handheld wireless MIC 1. Dynamic receiver Screen 2. Power indicator 3. Switch 4. Battery compartment 5. Compartment cover C.Transmitter You can get the better sound effect from the nearer distance between the microphone and you mouth. 1. Power Switch 2. Microphone Jack 3. Volume Control 4. Power indicator 5. Microphone,This microphone could be either lapel or headset type. 3. Basic Operation How system works? This HS321 PA system is a well built unit that can deliver great sound with high quality, the specially made speaker gives a full range response from low to high up to 16 KHz. It is a portable system that can run on both AC or DC, with the lead acid rechargeable battery built in, this system can last as long as up to 8 continuous hours ( the battery capacity gets low with time eclipsed, so the working time may get shorter.) The included VHF wireless handheld microphone OR the included VHF belt pack transmitter transmits the audio to the wireless receiver inside the HS321 amplifier. An audio sound source such as a CD player, tape player or DVD player can be used as an additional input source by plugging it into the 1 l4' cable to the auxiliary input jack on the top. This system can be directly powered by DC from a battery pack or car cigarette lighter output. (12VDC) An over discharge protection circuit is built in, when the battery voltage drops to or below 9,010.5V, the system enters protection mode and the power is cutoff completely, the system shuts down. At this point, you have to use AC as power or charge the battery to full before you can use it again. Warning: The system has to be charged within 10 days after it enters protection mode, otherwise the battery could be irrevocably damaged. How to use the system? Plug the included power cord into the rear AC jack, and plug the other end into a standard 110V AC wall jack. The system can used fully portable if the internal rechargeable battery has been charged up to a capacity with an overnight charge from an AC power outlet. 1. Using the Handheld Microphone. Put the 9V battery into the battery compartment and make sure you have the right polarity, then plug in the either the headset mic or lapel mic, you can talk into the mic and you will hear audio from the PA amplifier speaker. Using the belt pack transmitter. Put the 9V battery into the belt pack transmitter, and turn on the power switch. You then should hear audio from the PA amplifier speaker. Either the handheld microphone Or the belt pack transmitter can be used, but not at the same time, othenNise you will hear nothing or noise only. 4.Charging the battery This system comes with a lead acid rechargeable battery, like the one you use in a computer backup battery. . Plug the power cord into the system, and the other end of the power cord is connected to a power outlet from wall. Turn on the power switch to charging side; you will see the charging LED will light up. When the battery is charged up full, the LED will go out. The way to charge the built-in maintenance-free battery 1. One time full charge will supply 6-8 hours operation, but it need 6 hours or more to charge.(lf the power switch is set at POWER 0?! ,i)t is a slow charge which will take over 30 hours to charge it uII . Connect the power cord to power source, switch to CHARGE ON position. . The LED CHARGE ON lights up, it shows the charging is on,when the indicator goes off,it shows the battery is fully charged,then you can stop charging. . If the Charge On LED is not on or Not off,it shows the battery is dead or the charging circuit is malfunctioning. . The over charge protection mode guarantees there is no over charge on the battery .The circuit shuts off when the battery is fully charged. 6. If the operation time is less than 5 hours for a full charge, the battery might be damgde or aging. The way to change the battery To change the battery:0pen the battery compartment and take the battery out, make sure the polarity is correct.After the installation of the battery,p|ease charge the battery immediately for over 6 hours. Built in rechargeable battery Caution:Make sure the polarity of the battery is connected correctly, any mistake may damage the battery permanently ,and charge the battery as soon as possible. Warning: 1. In the charging processing, the charging LED goes on and off sometimes, it is normal to see so because the circuit tries to complete the charging intermittently. 2. The charging procedure is fully automatically controlled, the charging stops when the battery is fully charged and the charge LED turns off. No worry about the charging. Important Notice: You have to charge the internal battery every 3 months, even if you do not use it.lf it is not charged at least one time every 3 months, the capacity will get lower and lower. Warning: 1. When the system enters protection mode, the system shuts down completely, all the indicators are disabled. You have to plug it to AC power or charge it to full before you can use it. 2. After the system enters protection mode, you have to charge the system within 10 days, otherwise the battery will be damaged for good. 3. The charging procedure is fully automatically controlled, the charging stops when the battery is fully charged and charge LED turns off. No worry about the charging. 4. The system must be recharged over 8 hours every 3 months if you are not using it for a long time, or the battery life is shorten. 5. The built-in battery is NOT a warranted item due to its consumable. 5.8pecifications 0 RF carrier frequency range. (Available frequencies depend on applicable regulations in the country where the system is used.) 0 Operating range: 100 Meters (Approximate 300 feet) under ideal conditions. It might vary with the terrace condition and barrier between the transmitter and receiver. 0 Audio frequency response: 50 Hz to 15,000 Hz, at iSdB, THD< 1% 0 Audio output level: 0 - 1300mV O S/N ratio: > 85dB 0 Crystal control 0 Receiving sensitivity: -105dB 0 Image & spurious rejection: > 70 dB 0 Board upon channel rejection > 70 dB 0 Power source: 110V /60 Hz 0 Speaker power: 50W MAX 0 Speaker size: 16 CM ( 7 Inches) 0 Operation temperature range:—20°C to 74°C ( -4 “F to 172 °F). Note : The battery life may vary at extreme low or high temperature. 0 Dimensions: 180 mmX145mmX300mm O Receiver Weight: Net 5Kg. Important Notice: Hisonic is a trademark of Hisonic International, Inc. This manual is the property of Hisonic International Inc and Hisonic has copyright of this manual, any reprint or copy of this manual without an authorization from Hisonic International Inc is an infringement of the copy right of Hisonic. Montclair, California, USA www.hisonic.net 1-866-524 8676 6.Troubleshooting Please contact Hisonic Intemational Inc by email or phone for any questionsPIease check details from www.hisonic.net. No sound and receiving LED does not Ilght up 9V battery is installed with wrong polarity Problem Indicator status Solution Wireless mic or PA speaker Check the power switch on does not turn on Mic and PA speaker Check the battery and make sure the polarity Is correct. 9V battery is low in voltage Change the battery The PA speaker has low battery PA speaker/ Microphone volume control is set to minimum No Sound but the LED on PA speaker Is on Lapel microphone wire is broken Wireless microphone is set to standby mode. 9V battery is low in voltage PA speaker built in battery is low Lapel microphone wire is broken or bad Wireless microphone is too far from the PA speaker External interference from other equipments Screaming Main PA speaker is too close to the microphones Facing the PA speaker with the microphone Tone is set to high Battery maybe damaged or CD/AC fuse IS broken Main PA speaker no power source Use AC instead of the battery, and charge it. Increase the volume on PA system and microphone Change the wire. Switch to on position Change the battery Charge the battery immediately. Change to a new one. Get closer Change to another frequency Try to use it 5 meters away from the each othert Change the direction Adjust the tone control Change a new Battery or fuse
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 About : uuid:58b96605-4a33-4933-9368-150652a12cd8 Modify Date : 2007:11:06 09:08:58+08:00 Create Date : 2007:11:05 23:12:46+08:00 Metadata Date : 2007:11:06 09:08:58+08:00 Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:d55bf152-24c7-44d7-b4d3-b324b9dabf1b Instance ID : uuid:0ed7062e-5b99-4f30-bee8-99f9575d0df2 Format : application/pdf Creator : henly.xie Title :EXIF Metadata provided by EXIF.toolsProducer : Acrobat Distiller 6.0.1 (Windows) Has XFA : No Page Count : 10 Author : henly.xie