Bewator 5PQ-SM500 Contactless Smartcard Reader User Manual IN107

Download:
Mirror Download [FCC.gov]
Document ID	112102
Application ID	ueMixYX9o/54YyVq/qEbpw==
Document Description	Installation Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.22kB (15308 bits)
Date Submitted	2000-08-07 00:00:00
Date Available	2000-09-27 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat Distiller 3.0 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	Microsoft Word - IN107.DOC
Document Creator	PSCRIPT.DRV Version 4.0

Installation Note
SM501 Contactless Smartcard Reader and SM501K
Contactless Smartcard and PIN Reader
IN107
Mounting, connecting and setting up
Mount the Reader in a suitable position near the door approximately 1.2m from the
floor. The Reader can be installed outside in a sheltered position.
The Reader has a mounting plate with two oval mounting holes which are suitable for
most installations - you first need to break open the mounting holes using a
screwdriver. There are also four round holes in the mounting plate which will align
with a standard wall box of the type used, for example, for light switches.
1.
If the Reader is fixed to the mounting plate, undo the four screws which are in
each corner, then place the mounting plate in position on the wall or door
frame and mark the position of the two mounting holes. Note: the mounting
plate must be positioned with its connector at the top left.
2.
Drill the two mounting holes. The holes accept 3.5mm machine screws or No
6 wood screws.
3.
The connections are made to the connector on the mounting plate. Pass the
cable through the large hole in the centre of the mounting plate. Note: the two
power supply cables must be passed twice through the hole in the ferrite bead
supplied with the Reader before they are joined to the connector, as shown in
the following diagram:
from power supply
0V
to connector on mounting plate
V+
each cable passes through ferrite bead twice
4.
Make the connections shown in the following table as required:
Name
Function
V+
Power supply +V (+ve) unregulated DC
max 36.0V, min 10.0V, 250mA max
Power supply 0V (-ve),
(also ground reference for data output)
Either: Amber LED control - 0V for amber LED
Or: BCLINK data interface Rx
Horn - 0V to sound
Either: Red LED control - 0V for red LED
Or: BCLINK data interface address
Either: Green LED control - 0V for green LED
Or: Single wire LED control
0V for green LED, +5V for red LED
(0V also switches off amber LED)
Data zero for Wiegand output
Data for Mag Stripe output
BCLINK data interface Tx
Data one for Wiegand output
Clock for Mag Stripe output
Data Available for Wiegand or Mag Stripe output
0V
Amber
Horn
Red
Green
D0
D1
DA
IN107 - Issue 1A January 2000 - Page 1 of 2
Note: do not apply a voltage greater than +5V to the horn input or the LED
inputs
4.
Route the cable tidily, then screw the mounting plate to the wall or door
frame. Make sure all braid and loose filaments of wire are cut right back or
insulated with tape or sleeving.
5.
Set the jumpers on the Reader to provide the functions you require, as
described in the following tables:
INTERFACE
Jumper JU1
DATA
Jumper JU2
LED CONTROL
Jumper JU3
Function
32 bit Wiegand
34 bit Wiegand
10 character Mag Stripe
26 bit Wiegand
37 character Mag Stripe
Function
Read chip serial number from any Mifare card
Read Girovend information only from Girovend cards
Read Cotag information only from Cotag cards
not used
not used
Function
Internal - LED and horn inputs are disabled
Single wire LED control 0V on GREEN input for green LED,
+5V on GREEN input for red LED
External - LEDs and horn can be controlled using the
RED, GREEN, AMBER and HORN inputs - 0V to activate
BCLINK
6.
Locate the Reader on the mounting plate with the LEDs at the top left and
press it home - the Reader cannot be pushed fully home unless it is the
correct way round.
7.
Tighten the screws, then insert the little plastic plugs supplied with the
Reader into the screw-holes so that the screws cannot be seen and the case
looks neat. (Note that the plastic plugs cannot be removed without damaging
them - four spare plugs are supplied with each Reader.)
8.
Power up the Reader and test it: hold a smart card close to the outline of the
card engraved on the face of the Reader - the Reader should bleep when the
card is read and the host should receive the card data output. Each key-press
should give an amber flash and the host should receive PIN data.
For more information on the SM501 and SM501K Readers, please see the Handbook
HB02/104.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and 2) This device must accept any interference received, including
interference that may cause undesired operation.
IN107 - Issue 1A January 2000 - Page 2 of 2

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.1
Linearized                      : No
Page Count                      : 2
Create Date                     : 1910:00:32 11:44:20
Producer                        : Acrobat Distiller 3.0 for Windows
Creator                         : PSCRIPT.DRV Version 4.0
Title                           : Microsoft Word - IN107.DOC

EXIF Metadata provided by EXIF.tools