BiSRO MB-SFG PART15 REMOTE CONTROL/SECURITY DEVICE TRANSCEIVER (TWO-WAY CAR MAIN CONTROLLER) User Manual
BiSRO Co.,Ltd. PART15 REMOTE CONTROL/SECURITY DEVICE TRANSCEIVER (TWO-WAY CAR MAIN CONTROLLER)
BiSRO >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1163496 |
| Application ID | cgW1M6p9UORuUFEe7dyZHw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 73.97kB (924642 bits) |
| Date Submitted | 2009-09-02 00:00:00 |
| Date Available | 2009-09-02 00:00:00 |
| Creation Date | 2009-08-28 10:32:31 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2009-08-28 11:39:31 |
| Document Title | User manual |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | ghpark |
ZN-502 A/S/AS USER MANUAL Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations. We are constantly working to research, design, and build next generation products. We would not expect anything less since we Attention: This product’s antenna type is an Helical and permanently attached inner product and also comply with a FCC required standard section 15.203 Statement : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful Interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation. The below a two product is market with a one Box - Two-way Remote Controller FCC ID: WJ3ALC-502G - Two-way Main Controller FCC ID: WJ3MB-SFG Above product type is transceiver, accordingly the receiver portion of the respectively product is proceed a DoC under the Verification procedure CAUTION! PLEASE READ CAREFULLY This device under provision section 15.21 of FCC Rule Part 15 that changes or modiications not epressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. The user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system. Not reading the manuals completely may result in injury or damage to the user(s), installer(s), and/or the vehicle. Installation and use of this system is acknowledgment that the user and installer have fully read the manuals and indemnify Zenesis Electronics Corporation from any injuries or damages resulting from wrong use and/or installation of our system. Please take the following minimum precautions. 1. When using remote start, place the gear in Park(P) (automatic transmission) or Neutral (manual transmission) and set the parking brake (emergency brake). 2. The transmission (Tx) and reception (Rx) distance will vary from interference from other radio signals. 3. If any defects are discovered, do not open or attempt to repair the system. Ask the installer for assistance. 4. Zenesis Electronics Corporation will not be responsible for any theft and/or damages to your vehicle. 5. The user of this system will be responsible for any injuries and/or damages resulting from misuse. 6. Zenesis Electronics Corporation does not condone the installation of ANY remote starter equipped product into a convertible or open-concept type vehicle. 7. The user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment CONTENTS 1. Introduction 1.1 1.2 1.3 1.4 System Contents Remote Control Button Layout LCD Display Introduction Remote Control Button Introduction 2. Primary Features 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Door Lock (Arm) Door Unlock (Disarm) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start 11 11 11 12 12 12 13 2.8 2.9 Trunk Release Valet Mode 14 14 3. Secondary Features 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 Remote Control Beep Mute Siren Passive Lock (Arm) Safety Relock (Rearm) Ignition Lock Cold Start Timer Turbo Timer Option 1 Input Remote Control Registration Remote Start Registration User Programmable Options Time, Time Alarm, Timer Remote Start Reservation Set Aux 1 Output Aux 2 Output Shock Sensor Option Shock Sensor Sensitivity Adjustment Z-Pass Touch 4. Factory Rese 5.Others 26 4. Warranty Card 16 16 17 17 18 18 19 19 20 20 21 22 23 23 23 24 24 27 1. INTRODUCTION 1.1 1.2 1.3 1.4 System Contents Remote Control Button Layout LCD Display Introduction Remote Control Button Introduction 1.1 System Contents Main Control Module Remote Control Antenna Wiring Harness Shock Sensor Z-PASS TOUCH Manuals Siren 1.2 Remote Button Control Layout Front View Antenna OLCD / UCLCD CAUTION NEVER use the system except for its intended use. This is an electronic system with complex circuitry. Avoid dropping the components or cause any other physical damage as that will void the warranty. Buttons Battery 1.5 V AAA Back View Lock / Unlock 2-way Main Remote & Controller Specifications - Please see the page 26 Button(s) Duration* Description Ⅰ 0.5 sec Arm / Door Lock Ⅱ 0.5 sec Disarm / Door Unlock Ⅲ× 3 Times 0.5 sec Remote Control Hold ON/OFF Ⅳ 0.5 sec Vehicle Status / Car Finder Ⅰ- 2+ sec Panic Ⅲ- 2+ sec Remote Start Ⅳ- 2 sec Trunk Release Ⅱ~ 4 sec Time / Alarm / Remote Start Timer Set Ⅰ+Ⅳ 0.5 sec Remote Control Beep Mute ON/OFF Ⅱ+Ⅲ 0.5 sec Siren Mute ON/OFF Ⅰ+Ⅱ 0.5 sec Aux 1 Ⅲ+Ⅳ 0.5 sec Aux 2 1.3 LCD Display Layout 1.4 Remote Control Button Introduction 10 LEGEND: “ - “ means to hold for 2 seconds - press and hold button(s) until 1st beep is heard from the remote control. “ ~ “ means to hold for 4 seconds - press and hold button(s) until 2nd beep are heard from the remote control. Status Z-Pass LED’s Armed Mode Normal Flash Disarmed Mode No Flash Triggered Alarm Fast Flash 2. PRIMARY FEATURES 11 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 Arm (Door Lock) Disarm (Door Unlock) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start Trunk Release Valet Mode 2.1 Door Lock (Arm) ButtonⅠ 0.5 sec Successful Arm (Door Lock) Remote Control Vehicle flash. 1 beep will occur. 1 parking light flash & 1 siren chirp Failed Arm (Door Lock) If a door, while chirps will occur immediately. trunk and/or hood is open arming, 4 siren parking light flashes and 4 Please ensure any doors, trunk and/or hood that is open, is closed. Rearm the system. 12 2.2 Door Unlock (Disarm) Button Ⅱ 0.5 sec Successful Disarm (Door Unlock) will blink until remote start is turned off. 1 beep will occur if the main Remote Control control module communicates with the remote control. 5 beeps will occur after remote start is successful. Vehicle Remote Control Vehicle 1 parking light flash & 1 siren chirp if the main control module communicates with the remote control. 5 parking light flashes & 5 siren chirps after remote start is successful. Reason for Failure Vehicle Remote Control Key at ON Position 1 parking light flash & 1 siren chirp 3 beeps Open Door 3 parking light flashes & 3 siren chirps 3 beeps Open Hood and/or Trunk 4 parking light flashes & 4 siren chirps 3 beeps Failed Remote Start Reservation for Manual Transmission Vehicles 7 parking light flashes & 7 siren chirps 3 beeps occur. will flash. 2 beeps will 2 parking light flashes & 2 siren chirps. 2.3 Arm / Disarm Status Ⅱ 0.5 sec After the alarm is triggered, pressing Button II will stop the siren from sounding. The system is still armed at this point. Pressing Button II again will disarm the system. The LED’s on the Z-Pass module (while Discreet Mode is OFF) and 13 the LED on the Antenna Module will indicate the status of the system. If a door is opened and closed, the Triggered Alarm status will blink. 2 Remote Control on the Z-Pass will be beeps will occur. cleared. Vehicle 2 x parking light flashes & 2 siren chirps The siren duration can be programmed through the User Programmable Options 2.4 Vehicle Status / Car Finder Button Ⅳ 0.5 sec Remote Control Vehicle 1 will blink. 1 parking light flash & 1 siren chirp Remote Control OFF. Vehicle will stay ON. will blink. will turn 2 parking light flashes & 2 siren chirps 6 blinks & the vehicle’s inner temperature will be displayed. The Remote Control following status indications will be checked and displayed. If the status is normal, only the temperature will be displayed. 4 beeps will occur. Vehicle Open Door 14 Trunk 6 parking light flashes & 6 siren chirps Open Hood Open Remote Start On Shock Sensor Trigger Option 1 Input Trigger 2.5 Remote Control Hold ButtonⅢ 0.5 sec x 3 Times Pressing Button Ⅲ 3 times for 0.5 second each will put the remote control buttons into “Hold” mode. Any button presses will be ignored. To come out of “Hold” mode, press Button III 3 times for 0.5 second each again. Hold ON Hold OFF 2.6 Panic ButtonⅠ 2+ sec If there is a potential threat, you can alert those around you by using this feature. The siren will sound for 2 minutes and the parking lights will flash. Press either Button Ⅰ or Button Ⅱ to turn off panic mode. 2.7 Remote Start ButtonⅢ 2+ sec Successful Remote Start Failed Remote Start 15 If Button Ⅲ is pressed for 2+ seconds while remote start is on, remote start will turn off. The default remote start engine running time is 15 minutes. The time can be changed through the User Programmable Options. CAUTION: Do not use the remote start feature if the vehicle is in an enclosed area. Do not use the remote start feature where laws prevent its usage. Do not turn the key to the Start position or else damage may be done to the starter motor. Ensure that the parking brake (emergency brake) is always engaged. Do not use the remote start feature with convertible and/or open concept cars such as utility vehicles. 2.8 Trunk Release Button Ⅳ 2 sec Trunk release will unlock the door(s) and disarm the system. NOTE: On manual transmission vehicles, trunk release will turn off remote start. 2.9 Valet Mode ButtonsⅠ+ Ⅲ 4 sec Valet Mode ON 16 Valet mode OFF Valet mode without remote control (Emergency shut off) 1. Insert the key into the key cylinder and turn to the ON position. 2. Within 3 seconds, press the foot brake 6 times. 3. On the 6th press, hold down the foot brake until 1 parking light flash and 1 siren chirp occur. NOTE: This feature can be used to turn off the alarm with the key if the system has been triggered. NOTE: Valet mode can only be turned off via the remote control. 17 3.SECONDARY FEATURES 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 Remote Control Beep Mute Siren Mute Passive Lock (Arm) Safety Relock (Rearm) Ignition Lock Cold Start Timer Turbo Timer Option 1 Input Remote Control Registration Remote Start Reservation User Programmable Options Time, Time Alarm, Timer Remote Start Reservation Set Aux 1 Output Aux 2 Output Shock Sensor Option Shock Sensor Sensitivity Adjustment Z-Pass Touch 3.1 Remote Control Beep Mute ButtonsⅠ+ Ⅳ 0.5 sec Remote Control Beep Mute ON - Vibrate ON Remote Control Vehicle stay ON. will blink. will 1 parking light flash & 1 siren chirp When Remote Control Mute is ON, the remote control will use vibration alerts. Remote control mute OFF - Beeper ON 3.2 Siren Mute ButtonsⅡ+ Ⅲ 0.5 sec Siren Mute ON - Siren OFF Remote Control Vehicle 18 will blink . will stay ON. 1 parking light flash & 1 siren chirp No siren chirps will occur unless for alarm alerts (door trigger, hood trigger, trunk trigger, shock trigger, and/or Option 1 trigger) and panic mode. Siren Mute OFF - Siren ON Remote Control Vehicle OFF. will blink. will turn 2 parking light flashes & 2 siren chirps 3.3 Passive Arm (Lock) ButtonsⅠ+Ⅱ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + II are pressed for 4 seconds. Once a door is opened and closed and the system is not armed via the remote control, the system will automatically arm and lock the doors. The system will arm and lock the doors after 25 seconds of the last door closing. Every 5 seconds, 1 parking light flash and 1 siren chirp will occur. On the 5th occurrence, the system will arm and the doors will lock. Passive Arm (Lock) ON Remote Control Vehicle stay ON. will blink. will 1 parking light flash & 1 siren chirp Passive Arm (Lock) OFF Remote Control Vehicle turn OFF. will blink. will 2 parking light flashes & 2 siren chirps 3.4 Safety Rearm (Relock) ButtonsⅡ+ Ⅲ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons II + III are pressed for 4 seconds. If the system is in 19 the armed state and the system is disarmed but a door is not opened, the system will Safety Rearm automatically within 30 seconds. Safety Rearm (Relock) ON Remote Control stay ON. will blink. will 1 parking light flash & 1 siren chirp Vehicle Safety Rearm (Relock) OFF Remote Control turn OFF. will blink. will 2 parking light flashes & 2 siren chirps Vehicle 3.5 Ignition Lock ButtonsⅠ+ Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + IV are pressed for 4 seconds. Ignition lock will lock the doors when the foot brake is pressed after the key is put into key cylinder and turned to the ON position. If a door is opened while the key is in the ON position, the doors will lock again once the door is closed and the foot brake is pressed again. Ignition Lock ON Remote Control Vehicle stay ON. will blink. will 1 parking light flash & 1 siren chirp Ignition Lock OFF Remote Control OFF. Vehicle 2 parking light flashes & 2 siren chirps will blink. will turn 3.6 Cold Start Timer ButtonsⅡ+ Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons II+ IV are pressed for 4 seconds. Once Cold Start Timer I s turned ON, the vehicle will remote start automatically every 1, 2, or 3 hour(s) as specified by the User Programmable Options. If the vehicle is driven or 20 remote start is turned ON, the timer will automatically restart once the engine is turned OFF. The timer can be set through the User Programmable Options. Cold start timer ON Remote Control Vehicle will blink. will stay ON. 1 parking light flash & 1 siren chirp Cold start timer OFF Remote Control Vehicle will blink. will turn OFF. 2 parking light flashes & 2 siren chirps 3.7 Turbo Timer ButtonsⅢ + Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons III + IV are pressed for 4 seconds. This feature will allow turbocharged or supercharged vehicles to cool down by idling the engine for a specified amount of time even though the key is turn to the OFF position. The engine will continue to idle. Turbo Timer ON Remote Control Vehicle will blink. will stay ON. 1 parking light flash & 1 siren chirp Turbo Timer OFF Remote Control Vehicle will blink. will stay OFF. 2 parking light flash & 2 siren chirp The duration for idling can be specified through the User Programmable Options. CAUTION: Please ensure that the vehicle is in Park (automatic transmission) or Neutral (manual transmission). Also, ensure that the parking brake (emergency brake) is engaged. Do not idle the vehicle in an enclosed 21 area. Do not idle the vehicle if any laws prohibit this action. Do not idle the vehicle if it is a convertible or open concept type of vehicle. 3.8 Option 1 Input Additional sensors can be added to the system using Option 1 input. No additional programming is required. When the sensor is triggered, the parking lights will flash and the siren will sound. 3.9 Remote Control Registration 1. 2. 3. 4. Insert key and turn the key to ON position (engine is OFF). Press brake pedal 4 times. On the 4th press, hold the brake pedal down. 3 parking light flashes and 3 siren chirps will confirm remote control programming mode. 5. Press Button Ⅰ (Lock Button) . 6. After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren chirps. You can add up to 3 2-way remote controls and 2 1-way remote controls per system. 7. Once the key is turned to the OFF position or 10 seconds without adding a remote control passes, the system will exit remote control programming mode. ※ Each time a remote control is added, all remote controls must be reprogrammed to the system. Adding a remote control erases previously stored remote controls from the system. 3.10 Remote Start Reservation 22 Manual transmission vehicles require remote start reservation in order to ensure that the vehicle is properly prepared for remote start. There are 2 remote start reservation modes: automatic and manual. Please note that automatic and manual do not refer to the transmission type. Rather, automatic and manual refer to the type of remote start reservation. 1. Automatic Remote Start Reservation (Default) a. Before turning off the engine, put the transmission into Neutral. Ensure that the parking brake (emergency brake) is engaged. Take foot off of the foot brake. b. Turn the key to the OFF position. The engine should still be running. c. Exit the vehicle within 2 minutes. d. Once the last door is closed, the engine will turn off. e. Arm the system. Remote start is ready to be used. 2. Manual Remote Start Reservation a. Before turning off the engine, put the transmission into Neutral. Ensure that the parking brake (emergency brake) is engaged. Take foot off the foot brake. b. Press Button Ⅲ for 2 seconds. c. Turn the key to the OFF position. The engine should still be running. d. Exit the vehicle within 2 minutes. e. Once the last door is closed, the engine will turn off. f. Arm the system. Remote start is ready to be used. NOTE1: Remote start reservation type can be changed through the User Programmable Options. NOTE2: If a door, trunk, or hood is opened, remote start reservation will be cancelled and remote start will not be available. 3.11 User Programmable Options Buttons Ⅲ + Ⅳ 2 sec When you enter programming mode by holding Buttons III + Ⅳ for 2 seconds, you will hear Warning shock sensitivity adjustment 1 remote Full shock sensitivity adjustment control Green LED indicator for warning shock beep. Red LED indicator for full shock The parking lights will flash 1 time and the siren will chirp 1 time. You are now in programming mode. Follow the chart below for programming options. 23 User Option Button Sequence Options Ⅰ Ⅱ Ⅲ Remote Start Run Time Ⅳ→Ⅰ 15 min 5 min 25 min Diesel Warm Up Time Ⅳ→Ⅱ 30 sec 15 sec 7.5 sec Siren Sound Time Ⅳ→Ⅲ 30 sec 70 sec 100 sec Turbo Timer Run Time Ⅳ→Ⅳ 1 min 2 min 5 min Remote Start Reservation Ⅲ→Ⅳ Automatic Manual Cold Start Timer Ⅲ→Ⅲ 1 hour 2 hours Shock Sensor ON/OFF Ⅲ→Ⅱ ON OFF Temperature Unit Ⅲ →Ⅰ Fahrenheit Celsius 3 hours Default values. For example, to select 5 minutes for Remote Start Run Time, hold Buttons III + Ⅳ for 2 seconds. You will hear 1 remote control beep, see 1 parking light flash, and hear 1 siren chirp. Within 5 seconds, press Button IV. You will hear 1 remote control beep to signify the first button press. Press Button I to enter the Remote Start Run Time menu. You will hear 2 remote control beeps to signify the second button press. Now, press Button Ⅱ to select 5 minutes. You will hear 3 remote control beeps to signify the third button press. You will also hear 1 chirp and see 1 parking light flash. 3.12 Time, Alarm, Remote Start Timer Set ButtonⅡ4 sec The time, alarm, and remote start timer can be set by holding down Button I for 24 seconds. The following buttons are used. ButtonⅠ : Time Menu (Time → Alarm→ Remote Start Timer) 4. Triggers The following triggers will occur ONLY when the system is armed. Shock Trigger Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Door Trigger Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Hood Trigger Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Trunk Trigger Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Alarm Trigger During Remote Start Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Option 1 Trigger Remote Control Vehicle will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Low Battery Remote Control will blink. The remote control will beep every hour. Vehicle Press and hold Button Ⅱ for 4 seconds. Once the time starts to blink, toggle to Alarm and Remote Start Time and back to Time by pressing Button I for 0.5 second at a time. 25 ButtonⅡ : Hours setting. WARRANTY CARD Press and/or hold Button II in order to increase the hours value. Button Ⅲ : Minutes setting. Use this warranty card for your records. Please go to Press and/or hold Button III in order to increase the minutes value. Button Ⅳ: Confirmationwww.zenesisalarms.com or rejection. Visit the linkand above for specific and conditions. Press hold Button IV for 2warranty seconds interms order to accept the desired time or press for 0.5 second in order to reject the set time. ITU emission Code 8K50F1D Oscillation Type X-TAL NOTE : If a button is not pressed within 20 seconds of another press, programming mode will be exited. 1. Time - Clock Feature Displaying Current Time a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. (Frequency shifttokeying) Modulation TypeButtonⅡFSK b. Press and Button Ⅲ in order adjust the hours and minutes. c. Press and hold 1200 Buttonbps Ⅳ for 2 seconds in order to confirm the set Data Rate (Mbps) time. 2. Alarm - Alarm Clock 433.920 Feature ㎒ Operated Frequency a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. b. Press Button I for 0.5Channel second to toggle to Alarm setting. One Channel Number c. Press ButtonⅡ and Button Ⅲ in order to adjust the hours and minutes. Communication Type d. Press and hold Simplex(Two-way) Button Ⅳ for 2 seconds in order to confirm the set time. e. temperature The icon(-)will40℃ appear. ~ (+) 80 ℃ Operation 3. Remote Start Timer Set - Remote Start will occur at the specified time if Remote Controller: all constraints on remote- start met. each 250 are g / 66 (L)Remote ㎜ x 30Start (W) will ㎜ xoccur 15 (D) ㎜day at the Weight / Dimension specified time until the feature is turned OFF. Main Controller: a. Press and hold Button Ⅱ for 4 seconds. The time will begin to blink. 140 (L) 95 (W)each ㎜ xto30 (D) ㎜ b. Press Button I twice for ㎜ 0.5xsecond toggle to Remote Start Timer setting. Controller: c. Press ButtonⅡRemote and Button Ⅲ in order to adjust the hours and 1.5 Vdc (Alkaline battery), Size: AAA minutes. Power Source d. Press and hold Button Ⅳ for 2 seconds in order to confirm the set time. Main controller:: 12Vdc (Use the Car Adaptor) e. The icon will appear. 3.13 Aux 1 Output Buttons Ⅰ + Ⅱ 0.5 sec Aux 1 output can be used to control other devices such as window modules for rolling up or rolling down windows. Press Buttons Ⅲ + Ⅳ for 0.5 second to activate Aux 1 output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. 26 27
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2009:08:28 10:32:31+09:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2009:08:28 11:39:31-04:00 Metadata Date : 2009:08:28 11:39:31-04:00 Format : application/pdf Title : User manual Creator : ghpark Document ID : uuid:d9197fae-4c8e-44e2-bea5-9727c3cdbfc8 Instance ID : uuid:a88a1dc7-d36c-46ba-885c-8d7906ebfd1e Page Count : 28 Author : ghparkEXIF Metadata provided by EXIF.tools