Bilian Electronic R8723BT1 IEEE 802.11b/g/n WLAN BT Combo USB Module User Manual

Shenzhen Bilian Electronic Co., Ltd. IEEE 802.11b/g/n WLAN BT Combo USB Module

User Manual

Download: Bilian Electronic R8723BT1 IEEE 802.11b/g/n WLAN BT Combo USB Module User Manual
Mirror Download [FCC.gov]Bilian Electronic R8723BT1 IEEE 802.11b/g/n WLAN BT Combo USB Module User Manual
Document ID2846898
Application ID4QU1WgSMgGiSh+hR3j8yXA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize163.43kB (2042835 bits)
Date Submitted2015-12-18 00:00:00
Date Available2015-12-23 00:00:00
Creation Date2015-11-12 09:45:52
Producing SoftwareAdobe Acrobat Pro 9.0.0
Document Lastmod2015-12-18 11:35:35
Document TitleUser Manual
Document CreatorAdobe Acrobat Pro 9.0.0

DSSS
FCC Statment
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused
by unauthorized modifications to this equipment. such modifications could void the
user’s authority to operate this equipment.Any Changes or modifications not
expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
RF warning statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used in Mobile exposure condition with a 20cm distance restriction.
The modular can be installed or integrated in mobile or fix devices only. This modular
cannot be installed in any portable device, for example, USB dongle like transmitters
is forbidden.
Co-location statement
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
If the FCC identification number is not visible when the module is installed inside
another device, then the outside of the device into which the module is installed
must also display a label referring to the enclosed module. This exterior label can use
wording such as the following: “Contains Transmitter Module FCC ID: S8J-R8723BT1
Or Contains FCC ID: S8J-R8723BT1 ”
when the module is installed inside another device, the user manual of this device
must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product.
Any company of the host device which install this modular with limit modular
approval should perform the test of radiated emission and spurious emission
according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result
comply with FCC part 15C : 15.247 and 15.209 requirement,then the host can be
sold legally.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2015:11:12 09:45:52+08:00
Creator                         : Adobe Acrobat Pro 9.0.0
Modify Date                     : 2015:12:18 11:35:35+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2015:12:18 11:35:35+08:00
Creator Tool                    : Adobe Acrobat Pro 9.0.0
Format                          : application/pdf
Document ID                     : uuid:6e45995b-1864-4928-baf4-b26a661ca4dd
Instance ID                     : uuid:2270367d-9e9d-4b78-ac98-d05d28dc64e7
Producer                        : Adobe Acrobat Pro 9.0.0
Page Count                      : 3
EXIF Metadata provided by EXIF.tools
FCC ID Filing: S8J-R8723BT1

Navigation menu