Billion Electric BIL-BEC7700N High Speed ADSL2+/FTTH Router User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3223913
Application ID	+5MUPNFJs6BtVntEF/ldbQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	72.28kB (903476 bits)
Date Submitted	2016-12-09 00:00:00
Date Available	2016-12-11 00:00:00
Creation Date	2016-10-12 04:11:43
Producing Software	Microsoft® Word 2016
Document Lastmod	2016-12-02 11:10:07
Document Title	User Manual
Document Creator	Microsoft® Word 2016
Document Author:	Cindy C

USER MANUAL
WHAT’S IN THE BOX
 1 x BEC 7700N Router
 1 x This Quick Install Guide
 1 x RJ-11 ADSL / Phone Cable
High Speed ADSL2+/FTTH Router
 1 x RJ-45 Ethernet (CAT-5) LAN Cable
 1 x DC Power Adaptor 12V 1A
DEVICE OVERVIEW & LEDS
CONNECTION TO THE HARDWARE
Power
Green: Power on and system ready.
Off: Power off
LAN 1-4
Green: Connected to a 10/100Mbps device
Flashing: Data being transmitted / received
WLAN (Wi-Fi)
Green: Wi-Fi ready
Flashing: Data being transmitted / received
Off: Wi-Fi off
WPS
Flashing: WPS enabled and try to establish a connection
Off: WPS off
DSL
Green: Successfully connected to an ADSL DSLAM
(ADSL link is up)
Flashing: Ready to synch with a DSLAM
Off: DSL link is not ready or DSL cable is unplugged
Internet
Green: IP traffic via WAN (Internet connected)
Flashing: Data being transmitted / received
Red: WAN IP request failed
Off: No WAN connection or in Bridge mode
IMPORTANT - MUST READ
 Do not use the router in high humidity or high temperatures.
 Place the router on a stable surface.
 Do not place the router next to high-temperature appliance, e.g. a heater
or stove, or cover it up with tablecloths, curtain, etc.
 Only use the power adapter that comes with the package.
Using a different voltage rating power adapter may damage
the router.
 Do not use the same power source for the router as other equipment.
Warning
 Do not open or repair the case yourself. If the router is too hot, turn off the
power immediately and have it repaired at a qualified service center.
 Avoid using this product and all other accessories outdoors.
Attention
SETTING UP THE ROUTER
Plug in the supplied power adapter to the wall jack, the other side to
the 7700N then power ON the unit by pressing the Power On/Off
Switch button.
For ADSL WAN Connection, please connect the supplied RJ-11
phone cable to the DSL port then the other side of the cable to a
splitter or directly to a phone jack on a wall.
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet
ports, and the other side to the PC’s Ethernet interface.
For Ethernet WAN (EWAN) Connection, connect a RJ-45 Ethernet cable
to the EWAN port, and connect the other side to another alternative
broadband device, such as Cable, VDSL, Fiber Modem or PON optic line.
CONNECTING TO THE INTERNET
Step 1: Connecting to the 7700N
The default IP of modem is 192.168.1.254 with subnet 255.255.255.0. Make sure the attached PC to this router is in the same subnet and has an IP address in the range between
192.168.1.1 ~ 192.168.1.253.
Open a web browser and type http://192.168.1.254 in the URL address bar and press Enter
Before start configuring your BEC 7700N, make sure you have the WAN port connected to phone jack or with your Internet box or fiber line.
Use the Quick Start feature to quickly setting up your Internet connection.
Step 2: Quick Start - WAN Connection Setup
Select the Main network interface for your Internet connection, DSL or Ethernet (EWAN) mode.
Click Continue to the next step
CONNECTING TO THE INTERNET (CONT.)
Step 3: Quick Start - Internet Connection Setup
Next to Type, select your Internet connection and fill out all of the appropriate fields.
Step 4: Quick Start - Connection attempts to the Internet
Wait for 10 - 30 seconds for 7700N to establish an Internet connection.
Step 5: Quick Start - Internet connection established
“Congregations!” message will be shown if the Internet connection is ready to go.
Step 5: Quick Start - Setup Wireless Connection
Setup the SSIDs and setup the Security Passphrase (WPA2-PSK/AES) to secure your wireless network.
Click Continue to enjoy your Wi-Fi access connection.
FAQ
1.
None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have a hardware problem. In this case you should contact technical support.
2.
You have forgotten your router login and/or password.
Try the default login and password, please refer to User Manual. If this fails, you can restore your router to its factory settings by holding the Reset button on the back of your
router for 6 seconds or more.
3.
Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC connected. If it is off, check the cables between your router and the PC. Make
sure you have uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet mask are consistent between the router and the workstations.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Warning                         : Invalid secondary xref table
Page Count                      : 4
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Microsoft® Word 2016
Format                          : application/pdf
Creator                         : Cindy C
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2016:10:12 04:11:43-04:00
Modify Date                     : 2016:12:02 11:10:07+08:00
Metadata Date                   : 2016:12:02 11:10:07+08:00
Document ID                     : uuid:01EC3292-EE14-4A78-8B30-3354CD047511
Instance ID                     : uuid:152b3fa6-dc39-4d6b-93a9-d6ae2683b408
Author                          : Cindy C

EXIF Metadata provided by EXIF.tools