Billion Electric BIL-MX210NP 4G/LTE Broadband Router with PoE User Manual Product Overview

Billion Electric Co., Ltd. 4G/LTE Broadband Router with PoE Product Overview

Users Manual

Last revised: May, 2018 Version release: v1.01 User Manual BEC MX-210NP 4G/LTE Wi-Fi Router with PoE
Copyright Notice Copyright@ 2017 BEC Technologies Inc. All rights reserved. BEC Technologies reserves the right to change and make improvement to this manual at any time without prior notice. No part of this document may be reproduced, copied, transmitted in any form or by any means without prior written permission from BEC Technologies, Inc. Support Contact Information Contact Support: http://bectechnologies.net/support/. Telephone: +1 972 422 0877
TABLE OF CONTENTS COPYRIGHT NOTICE ....................................... 1 SUPPORT CONTACT INFORMATION ............. 1 CHAPTER 1: INTRODUCTION ......................... 1 INTRODUCTION TO YOUR ROUTER .............................................................. 1 FEATURES & SPECIFICATIONS .................................................................... 3 HARDWARE SPECIFICATIONS ..................................................................... 5 CHAPTER 2: PRODUCT OVERVIEW ............... 6 IMPORTANT NOTE FOR USING THIS ROUTER ................................................ 6 PACKAGE CONTENTS ............................................................................... 6 DEVICE DESCRIPTION .............................................................................. 7 Front Panel LEDs................................................................................................ 7 Rear Panel Connectors ...................................................................................... 8 SYSTEM RECOVERY PROCEDURES ............................................................... 9 CABLING .............................................................................................. 9 CHAPTER 3: BASIC INSTALLATION ............ 10 NETWORK CONFIGURATION – IPV4 ......................................................... 11 Configuring PC in Windows 10 (IPv4) .............................................................. 11 Configuring PC in Windows 7/8 (IPv4) ............................................................. 13 Configuring PC in Windows Vista (IPv4) .......................................................... 15 NETWORK CONFIGURATION – IPV6 ......................................................... 17 Configuring PC in Windows 10 (IPv6) .............................................................. 17 Configuring PC in Windows 7/8 (IPv6) ............................................................. 19 Configuring PC in Windows Vista (IPv6) .......................................................... 21 DEFAULT SETTINGS ............................................................................... 23 CHAPTER 4: DEVICE CONFIGURATION ...... 24
LOGIN TO YOUR DEVICE ......................................................................... 24 STATUS .............................................................................................. 26 Device Info ...................................................................................................... 26 System Status .................................................................................................. 28 System Log ...................................................................................................... 28 4G/LTE Status .................................................................................................. 29 Wireless Status ................................................................................................ 31 Statistics .......................................................................................................... 32 DHCP Table ...................................................................................................... 36 ARP Table ........................................................................................................ 36 VRRP Status ..................................................................................................... 36 QUICK START ...................................................................................... 37 DEVICE CONFIGURATION ....................................................................... 40 Interface Setup ................................................................................................ 40 Internet ........................................................................................................................ 40 LAN ............................................................................................................................... 48 Wireless ........................................................................................................................ 52 Wireless MAC Filter ...................................................................................................... 56 Loopback ...................................................................................................................... 57 Dual WAN ........................................................................................................ 58 General Setting ............................................................................................................. 58 Outbound Load Balance ............................................................................................... 62 Protocol Binding ........................................................................................................... 63 Advanced Setup .............................................................................................. 65 Firewall ......................................................................................................................... 65 Routing ......................................................................................................................... 66 NAT ............................................................................................................................... 67 VRRP............................................................................................................................. 72 Static DNS ..................................................................................................................... 73 QoS ............................................................................................................................... 74 Time Schedule .............................................................................................................. 76 Mail Alert ..................................................................................................................... 77 Access Management ....................................................................................... 78 Device Management .................................................................................................... 78 SNMP ........................................................................................................................... 79 Syslog ........................................................................................................................... 81 Universal Plug & Play ................................................................................................... 82 Dynamic DNS (DDNS) ................................................................................................... 83
Access Control .............................................................................................................. 85 Packet Filter .................................................................................................................. 87 CWMP (TR-069) ............................................................................................................ 91 Parental Control ........................................................................................................... 93 BECentral Management ............................................................................................... 94 Maintenance ................................................................................................... 95 User Management ....................................................................................................... 95 Certificate Management .............................................................................................. 97 Time Zone ..................................................................................................................... 99 Firmware & Configuration .......................................................................................... 100 System Restart ............................................................................................................ 101 Auto Reboot ............................................................................................................... 102 Diagnostics Tool .......................................................................................................... 103 CHAPTER 5: TROUBLESHOOTING ............ 106 Problems with the Router ............................................................................. 106 Problem with LAN Interface .......................................................................... 106 Recovery Procedures ..................................................................................... 107 APPENDIX: PRODUCT SUPPORT & CONTACT ....................................................................... 108
Introduction 1 BEC MX-210NP User Manual CHAPTER 1: INTRODUCTION Introduction to your Router The BEC MX-210NP 4G/LTE 11n with PoE Router is a compact, affordable and high-performance fixed 4G/LTE Router incorporated 11n technology and offers flexible options such as dual-WAN failover by seamless connecting to other Internet Service Provider to avert internet downtown, redundant power source for safe & quick power installation via one of the versatile LAN/PoE-PD ports and secure network connection and data privacy with VPN encryption capabilities to provide a reliable and cost-effective alternative solution for business continuity. 4G/LTE Mobility The MX-210NP is a classic 4G/LTE router with dual WAN interfaces for redundancy or seamless failover between mobile carrier network and the wireline, an interchangeable Gigabit Ethernet LAN/WAN, to ensure continuous Internet connectivity. Seamless Wi-Fi Coverage The MX-210NP integrates a 802.11n access point supporting data rates of up to 300Mbps. Security functionality includes: WEP 64/128 bit, WPA, WPA2 (PSK, TKIP and AES, 802.1X, SSID broadcast disable and wireless MAC address filtering and MSSID with Client Isolation to enhance the level of transmission security and access control over the Wireless LAN. The router also supports the Wi-Fi Protected Setup (WPS) standard, allowing users to establish a secure wireless network by simply pushing a button. If the network requires wider coverage, the built-in Wireless Distribution System (WDS) repeater function allows users to expand the wireless network without the need for any external wires or cables. IPv6 Supported Internet Protocol version 6 (IPv6) is a version of the Internet Protocol that is designed to succeed IPv4. IPv6 has a vastly larger address space than IPv4. The router is already supporting IPv6, you can use it in IPv6 environment no need to change device. The dual-stack protocol implementation in an operating system is a fundamental IPv4-to-IPv6 transition technology. It implements IPv4 and IPv6 protocol stacks either independently or in a hybrid form. The hybrid form is commonly implemented in modern operating systems supporting IPv6. Quick Start Wizard Support a WEB GUI page to install this device quickly. With this wizard, simple steps will get you connected to the Internet immediately.
Introduction 2 BEC MX-210NP User Manual Firmware Upgradeable Device can be upgraded to the latest firmware through the WEB based GUI. 24/7 Cloud Management and Network Visibility Remote monitoring, management and control of devices in real-time is essential for IoT networking devices, M2M and critical applications. The BECentral®, BEC’s Cloud Based Remote Management, is a comprehensive device management platform designed to minimize deployment, lower support expenses and maximize the operational efficiency and profitability of the operator.
Introduction Features & Specifications 3 BEC MX-210NP User Manual Features & Specifications • 4G/LTE and/or Ethernet IP broadband connectivity • High performance SX antenna for increased coverage, signal reception and efficiency • Versatile Gigabit LAN & Ethernet WAN (GbE WAN) for Cable/Fiber/xDSL high WAN throughput • Verstalile Gigabit LAN & PoE • Firewall Security with DoS Preventing and Packet Filtering • Quality of Service Control for traffic prioritization management • Universal Plug and Play (UPnP) Compliance • Ease of Use with Quick Installation Wizard • Small form factor with multiple mounting options, easily installed by a single person Availability and Resilience • Dual-WAN Interfaces • Auto fail-over and failback • High performance external antennas Network Protocols and Features • IPv4, IPv6, IPv4 / IPv6 dual stack • IP Tunnel IPv6 in IPv4 (6RD) • IP Tunnel IPv4 in IPv6 (DS-Lite) • NAT, static routing and RIP-1/2 • Universal Plug and Play (UPnP) compliant • Dynamic Domain Name System (DDNS) • Virtual server and DMZ • SNTP, DNS relay • IGMP proxy and IGMP snooping • MLD proxy and MLD snooping • Supports port-based Virtual LAN (VLAN) Firewall • Built-in NAT Firewall • Stateful Packet Inspection (SPI) • DoS attack prevention including Land Attack, Ping of Death, etc.
Introduction Features & Specifications 4 BEC MX-210NP User Manual • Access control • IP&MAC filter, URL Content Filter • Password protection for system management • VPN pass-through Quality of Service Control •Traffic prioritization management based-on Protocol, Port Number and IP Address (IPv4/ IPv6) Management • Quick Installation wizard • Web-based GUI for remote and local management (IPv4/IPv6) • Firmware upgrades and configuration data upload and download via web-based GUI • Supports DHCP server / client / relay • Supports SNMP • TR-069 supports remote management • BECentral® Cloud Management
Introduction Hardware Specifications 5 BEC MX-210NP User Manual Hardware Specifications Physical interface • 4G/LTE: Two (2) detachable antennas • WAN: Cellular 4G/LTE (and/or ETH WAN Optional) • Ethernet LAN: 2-port 10/100/1000Mbps, auto-crossover (MDI/ MDI-X) switch • SIM Card: One (1) slot • Reset Button • Power Source: DC or PoE • LED Indicators: Power / Internet / LTE / Ethernet Physical Specifications • Dimensions (W*H*D): 5.19" x 1.38" x 3.71" (132mm x 35mm x 94mm)
Product Overview 6 BEC MX-210NP User Manual CHAPTER 2: PRODUCT OVERVIEW Important Note for Using This Router Package Contents ✓ BEC MX-210NP Router * 1 ✓ Quick Installation Guide * 1 ✓ RJ-45 Ethernet cable *1 ✓ DC Power Adapter, 12V 1.2A* 1 ✓ Do not use the router in high humidity or high temperature. ✓ Do not use the same power source for the MX-210NP on other equipment. ✓ Do not open or repair the case yourself. If the device becomes too hot, turn off the power immediately and have it repaired at a qualified service center. ✓ Avoid using this product and all accessories outdoors. Warning ✓ Place the router on a stable surface. ✓ Only use the power adapter that comes with the package. Using a different voltage rating power adaptor may damage the router. Attention
Product Overview Device Description (Front Panel LEDs) 7 BEC MX-210NP User Manual Device Description Front Panel LEDs LED STATUS DESCRIPTION Power Green System is up and ready Red Boot failure Ethernet Port LAN 1 ~ 2 Green Transmission speed is at Gigabit speed (1000Mbps) Orange Transmission speed is at 10/100Mbps Blinking Data being transmitted/received Wireless Green Wireless connection established Green blinking Data being transmitted / received Orange WPS configuration is in progress LTE (Received Signal Strength Indicator) Green RSSI greater than -69 dBm. Excellent signal condition Green Flashing quickly RSSI from -81 to -69 dBm. Good signal condition Orange Flashing quickly RSSI from -99 to -81 dBm. Fair signal condition. Orange Flashing slowly RSSI less than -99 dBm. Poor signal condition. Orange No signal and the cellular module is in service Off No LTE module or LTE module fails Green & Orange MX-210NP is either in debug mode or in upgrading firmwere process Internet Green IP address has received, and traffic is passing thru the device. Red IP address request has failed. Off MX-210NP is either in bridged mode or WAN connection not ready.
Product Overview Device Description (Rear Panel Connectors) 8 BEC MX-210NP User Manual Rear Panel Connectors INTERFACE MEANING 1 4G/LTE Antenna Connectors (Main/Aux) SMA female connectors. Manually screw the cellular antennas tight to the female connectors. Connect to Main if decide to use one antenna instead of two. 2 Power Source Power ON/OFF switch (1) with Power Switch ON: power up by the supplied DC power adapter (2) with Power Switch OFF: power up by the PoE battery unit 3 Power Jack (DC IN) Connect the supplied Power Adapter to this jack. 4 Rest After the device is powered on, press it 6 seconds or above: to restore to factory default settings (this is used when you cannot login to the router, e.g. forgot your password) 5 Gigabit Ethernet (LAN 1 / PoE) Ethernet LAN: Connected to an Gigabit (1000Mbps) Ethernet device Ethernet PoE: Connect with a 802.3at Gb PoE injector to provide power to the MX-210NP 6 Gigabit Ethernet (LAN 1 / EWAN) Ethernet LAN: Connected to an Gigabit (1000Mbps) Ethernet device Ethernet WAN: Software configurable in the GUI. Connected with a broadband connection device 7 SIM Card Slot Insert the mini SIM card (2FF) with the gold contact facing down. Push the mini SIM card (2FF) inwards to eject it * Power off the MX-210NP before inserting or removing the SIM card(s) 1 2 3 4 5 6 7 1
Product Overview System Recovery Procedure & Cabling 9 BEC MX-210NP User Manual System Recovery Procedures The purpose is to allow users to restore the MX-210NP to its initial stage when the device is outage, upgraded to a wrong / broken firmware, cannot access to the GUI with wrong username and/or password, etc. Step 1 – Configure your PC Network IP Address Before performing the system recovery, assign this IP address and Netmask to your PC, 192.168.1.100 and 255.255.255.0 respectively. Step 2 – Reset your MX-210NP Device 2.1 Power off your MX-210NP 2.2 Power on the MX-210NP while pushing the RESET button with a small pointed object (such as paper clip, needle, toothpick, etc.). 2.3 When the POWER LED turns RED, keep holding and pushing the RESET button until the INTERNET LED flashes in GREEN Step 3 – Restore your MX-210NP Device With INTERNET light flashes green, MX-210NP is in recovery mode and ready for a new Firmware. 3.1 Open a web browser and type the IP address, 192.168.1.1, to access to the recovery page. NOTE: In the recovery mode, MX-210NP will not respond to any PING or other requests. 3.2 Browse to the new Firmware image file then click Upload to start the upgrade process. 3.3 INTERNET LED turns red means the Firmware upgrade is in process. DO NOT power off or reboot the device, it would permanently damage your MX-210NP. 3.4 INTERNET LED turns green after the Firmware upgrade completed 3.5 Power cycle on & off to regain access to the MX-210NP. Cabling One of the most common causes of problems is bad cabling. Make sure that all connected devices are turned on. On the front panel of the product is a bank of LEDs. Verify that the LAN Link and LEDs are lit. If they are not, verify that you are using the proper cables.
Basic Installation 10 BEC MX-210NP User Manual CHAPTER 3: BASIC INSTALLATION The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Windows Vista / 7 / 8, Linux, Mac OS, etc. The product provides an easy and user-friendly interface for configuration. PCs must have an Ethernet interface installed properly and be connected to the router either directly or through an external repeater hub and have TCP/IP installed or configured to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is 192.168.1.254 and the subnet mask is 255.255.255.0 (i.e. any attached PC must be in the same subnet and have an IP address in the range of 192.168.1.1 to 192.168.1.253). The best and easiest way is to configure the PC to get an IP address automatically from the router using DHCP. If you encounter any problems accessing the router’s web interface it may also be advisable to uninstall any kind of software firewall on your PCs, as they can cause problems accessing the 192.168.1.254 IP address of the router. Users should make their own decisions on how to best protect their network. Please follow the steps below for your PC’s network environment installation. Check your PC’s network components first. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals. Any TCP/IP capable workstation can be used to communicate with or through the MX-210NP. To configure other types of workstations, please consult the manufacturer’s documentation. Attention
Basic Installation Windows 10 (IPv4) 11 BEC MX-210NP User Manual Network Configuration – IPv4 Configuring PC in Windows 10 (IPv4) 1. Click . 2. Click 3. Then click on Network and Internet. 4. Under Related settings, select Network and Sharing Center 5. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 6. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows 10 (IPv4) 12 BEC MX-210NP User Manual 7. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 8. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 9. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Windows 7/8 (IPv4) 13 BEC MX-210NP User Manual Configuring PC in Windows 7/8 (IPv4) 1. Go to Start. Click on Control Panel. 2. Then click on Network and Internet. 3. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 4. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows 7/8 (IPv4) 14 BEC MX-210NP User Manual 5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Windows Vista (IPv4) 15 BEC MX-210NP User Manual Configuring PC in Windows Vista (IPv4) 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window pane. 4. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows Vista (IPv4) 16 BEC MX-210NP User Manual 5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Windows 10 (IPv6) 17 BEC MX-210NP User Manual Network Configuration – IPv6 Configuring PC in Windows 10 (IPv6) 1. Click . 2. Click 3. Then click on Network and Internet. 4. Under Related settings, select Network and Sharing Center 5. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 6. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows 10 (IPv6) 18 BEC MX-210NP User Manual 7. Select Internet Protocol Version 6 (TCP/IPv6) then click Properties. 8. In the TCP/IPv6 properties window, select the Obtain an IPv6 address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 9. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Windows 7/8 (IPv6) 19 BEC MX-210NP User Manual Configuring PC in Windows 7/8 (IPv6) 1. Go to Start. Click on Control Panel. 2. Then click on Network and Internet. 3. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 4. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows 7/8 (IPv6) 20 BEC MX-210NP User Manual 5. Select Internet Protocol Version 6 (TCP/IPv6) then click Properties. 6. In the TCP/IPv6 properties window, select the Obtain an IPv6 address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Windows Vista (IPv6) 21 BEC MX-210NP User Manual Configuring PC in Windows Vista (IPv6) 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window pane. 4. Select the Local Area Connection, and right click the icon to select Properties.
Basic Installation Windows Vista (IPv6) 22 BEC MX-210NP User Manual 5. Select Internet Protocol Version 6 (TCP/IPv6) then click Properties. 6. In the TCP/IPv6 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Basic Installation Default Settings 23 BEC MX-210NP User Manual Default Settings Before configuring the router, you need to know the following default settings. Web Interface: (Username and Password) Administrator Username: admin Password: admin or a unique12-digit password can be found on the device label. Device LAN IP Settings IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 DHCP Server: DHCP server is enabled. Start IP Address: 192.168.1.100 IP pool counts: 100 If you ever forget the username/password to login to the router, you may press the RESET button up to 6 seconds then release it to restore the factory default settings. Caution: After pressing the RESET button for more than 6 seconds then release it, to be sure you power cycle the device again.
Device Configuration Login to Your Device 24 BEC MX-210NP User Manual CHAPTER 4: DEVICE CONFIGURATION Login to your Device Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt appears. The default username and password are “admin” and “admin” respectively for the Administrator. For the User account, default username and password is “user” and “user”. NOTE: This username / password may vary by different Internet Service Providers. Congratulations! You have successfully logged on to your MX-210NP
Device Configuration Login to Your Device 25 BEC MX-210NP User Manual Once you have logged on to your MX-210NP via your web browser, you can begin to set it up according to your requirements. On the configuration homepage, the left navigation pane links you directly to the setup pages, which includes: Section Status Quick Start (Wizard Setup) Configuration Sub-Items Device Info System Status System Log 4G/LTE Status Wireless Status Statistics DHCP Table ARP Table VRRP Status Interface Setup - Internet - LAN - Wireless - Wireless MAC Filter - Loopback Dual WAN - General Setting - Outbound Load Balance - Protocol Binding Advanced Setup - Firewall - Routing - Dynamic Routing - NAT - VRRP - Static DNS - QoS - Time Schedule - Mail Alert Access Management - Device Management - SNMP - Syslog - Universal Plug & Play - Dynamic DNS - Access Control - Packet Filter - CWMP (TR-069) - Parental Control - BECentral Management Maintenance - User Management - Certificate Management - Time Zone - Firmware & Configuration - System Restart - Auto Reboot - Diagnostic Tool Please see the relevant sections of this manual for detailed instructions on how to configure your MX-210NP device.
Device Configuration Status – Device Info 26 BEC MX-210NP User Manual Status Device Info It provides brief status summary of the device. Device Information Model Name: Name of the router for identification purpose. Firmware Version: Software version currently loaded in the router MAC Address: A unique number that identifies the router Data Time: Setup correct time on the MX-210NP with your PC. Check on Time Zone section for more configuration information. System Uptime: Display how long the MX-210NP has been powered on. Physical Port Status Physical Port Status：Display available connection interfaces, WAN (3G/4G-LTE, EWAN) and LAN (Ethernet) are supported in the MX-210NP. WAN Interface: List current available WAN connections. Protocol: Display selected WAN connection protocol Connection: The current connection status. IP Address: WAN port IP address. Default Gateway: The IP address of the default gateway. LAN
Device Configuration Status – Device Info 27 BEC MX-210NP User Manual IP Address: LAN port IPv4 address. Subnet Mask/Prefix Length: Display LAN port IP subnet mask of IPv4 and/or Prefix length of IPv6. DHCP Server: Display LAN DHCP status of IPv4 and IPv6.  Enable / 192.168.1.100~199: DHCPv4 server status on or off / DHCP IP range  Enable / Stateless: DHCPv6 server status on or off / DHCPv6 server Type  Wireless  Mode: Display selected Wireless mode.  SSID: Display the name of the Wireless AP(s) to use  Channel: Display radio frequency to be used for this wireless link  Security: Display security method to be used for this wireless link
Device Configuration Status – System Status & System Log 28 BEC MX-210NP User Manual System Status Display device CPU and memory usage information CPU Usage: Display the amount of CPU’s processing capacity is being used in percentage (%). Higher the % rate may result in slow Internet loading, experiencing video lags, etc. To reduce high CPU consumption by resetting the device, power off and on, an easiest way to regain the service. Memory Total / Free / Cached (in Kbyte): Display the memory consumptions in kilobytes (kB). System Log In system log, you can check the operations status and any glitches to the router. Refresh: Press this button to refresh the statistics. Backup: Press to save the System log, log.cfg, to your computer / notebook.
Device Configuration Status – 4G/LTE Status 29 BEC MX-210NP User Manual 4G/LTE Status It contains 3G/4G-LTE connection information. Status: The current status of the 3G/4G-LTE connection. Signal Strength: The signal strength bar and dBm value indicates the current 3G/4G-LTE signal strength. The front panel 3G/4G-LTE Signal Strength LED indicates the signal strength as well. Signal Information: Shows important LTE signal parameters such as RSRP (Reference Signal Receiving Power), RSRQ (Reference Signal Receiving Quality), SINR (Signal to Interference plus Noise Ratio).  RSRP (Reference Signal Receiving Power): is the average power of all resource elements which carry cell-specified reference signals over the entire bandwidth.  RSRQ (Reference Signal Receiving Quality): measures the signal strength and is calculated based on both RSRP and RSSI.  RSSI (Received Signal Strength Indicator): parameter which provides information about total received wide-band power (measure in all symbols) including all interference and thermal noise. Please refer to the Device Description for details.  SINR (Signal to Interference plus Noise Ratio): is also a measure of signal quality as well. It is widely used by the operators as it provides a clear relationship between RF conditions and throughput. NOTE: Some LTE modules do not provide this information. Network Name: The name of the LTE network the router is connecting to. Cell ID: The ID of base station that the device is connected to. Physical Cell ID: Display the actual PCI (Physical Cell ID) that device is attached and to transfer the data. Card IMEI: The unique identification number that is used to identify the 3G/4G-LTE module. Card IMSI: The international mobile subscriber identity used to uniquely identify the 3G/4G-LTE
Device Configuration Status – 4G/LTE Status 30 BEC MX-210NP User Manual module. Network Mode / Band: Show the using network mode and LTE band. Usage Allowance Amount Used: Display the amount of mobile data used and remaining in current billing cycle. Billing Cycle: Display the start date and number of days remaining in current billing cycle Clean: Reset current saved mobile usage Save: Click to save current mobile status to ROM Refresh: Click to refresh the page.
Device Configuration Status – Wireless Status 31 BEC MX-210NP User Manual Wireless Status MAC: The MAC of the connected wireless device. SSID: Display the total bytes transmitted till the latest second for the current connection for the current connection. RSSI: Display the signal strength between the wireless client and the AP (Access Point) Connected Time: Display the total amount of time the wireless client has connected with the wireless AP Host Name: Display the hostname of the Wi-Fi client. IP Address: The LAN IP address assigned to the wireless device. Expire Time: Display remaining time before connection expires or timeout.
Device Configuration Status – Statistics (4G/LTE) 32 BEC MX-210NP User Manual Statistics ❖ 4G/LTE Take 4G/LTE as an example to describe the following connection transmission information. Traffic Statistics Interface: List all available network interfaces in the router. You are currently checking on the physical status of 3G or 4G/LTE interface. Transmit Statistics Transmit Frames of Current Connection: Display the total number of 3G/4G/LTE frames transmitted until the latest second for the current connection. Transmit Bytes of Current Connection: Display the total bytes transmitted till the latest second for the current connection for the current connection. Transmit Total Frames: Display the total number of frames transmitted till the latest second since system is up. Transmit Total Bytes: Display the total number of bytes transmitted until the latest second since system is up. Transmit Speed: Display the data rate can be transferred to the server, the mobile Internet. Receive Statistics Receive Frames of Current Connection: Display the number of frames received until the latest second for the current connection. Receive Bytes of Current Connection: Display the total bytes received till the latest second for the current connection. Receive Total Frames: Display the total number of frames received until the latest second since system is up. Receive Total Bytes: Display the total frames received till the latest second since system is up. Receive Speed: Display the data rate receives from the mobile Internet. Refresh: Click to manually refresh the data. Auto Reresh: Select a time interval to refresh the data automatically or none to disable the feature.
Device Configuration Status – Statistics (EWAN/LAN #2) 33 BEC MX-210NP User Manual ❖ EWAN (LAN2) Traffic Statistics Interface: List all available network interfaces in the router. You are currently checking on the physical status of the EWAN (Ethernet #2) port. Transmit Statistics Transmit Frames: Display the number of frames transmitted until the latest second. Transmit Multicast Frames: Display the number of multicast frames transmitted until the latest second. Transmit Total Bytes: Display the number of bytes transmitted until the latest second. Transmit Collision: Numbers of collisions have occurred on this port. Transmit Error Frames: Display the number of error packets on this port. Receive Statistics Receive Frames: Display the number of frames received until the latest second. Receive Multicast Frames: Display the number of multicast frames received until the latest second. Receive Total Bytes: Display the number of bytes received until the latest second. Receive CRC Errors: Display the number of error packets on this port. Receive Under-size Frames: Display the number of under-size frames received until the latest second. Traffic Speed Transmit Speed: Display the data rate can be transferred to the server, the Broadband Internet Service Provider. Receive Speed: Display the data rate receives from the Broadband Internet Service Provider. Refresh: Click to manually refresh the data. Auto Reresh: Select a time interval to refresh the data automatically or none to disable the feature.
Device Configuration Status – Statistics (Ethernet) 34 BEC MX-210NP User Manual ❖ Ethernet Traffic Statistics Interface: List all available network interfaces in the router. You are currently checking on the physical status of the Ethernet port. Transmit Statistics Transmit Frames: Display the number of frames transmitted until the latest second. Transmit Multicast Frames: Display the number of multicast frames transmitted until the latest second. Transmit Total Bytes: Display the number of bytes transmitted until the latest second. Transmit Collision: Numbers of collisions have occurred on this port. Transmit Error Frames: Display the number of error packets on this port. Receive Statistics Receive Frames: Display the number of frames received until the latest second. Receive Multicast Frames: Display the number of multicast frames received until the latest second. Receive Total Bytes: Display the number of bytes received until the latest second. Receive CRC Errors: Display the number of error packets on this port. Receive Under-size Frames: Display the number of under-size frames received until the latest second. Traffic Speed Transmit Speed: Display the data rate can be transferred to the server, the LAN network. Receive Speed: Display the data rate receives from the LAN network. Refresh: Click to manually refresh the data. Auto Reresh: Select a time interval to refresh the data automatically or none to disable the feature.
Device Configuration Status – Statistics (Wireless) 35 BEC MX-210NP User Manual ❖ Wireless Traffic Statistics Interface: List all available network interfaces in the router. You are currently checking on the physical status of the Wireless. Transmit Statistics Transmit Frames: Display the number of frames transmitted until the latest second. Transmit Error Frames: Display the number of error frames transmitted until the latest second. Transmit Drop Frames: Display the number of drop frames transmitted until the latest second. Receive Statistics Receive Frames: Display the number of frames received until the latest second. Receive Error Frames: Display the number of error frames received until the latest second. Receive Drop Frames: Display the number of drop frames received until the latest second. Traffic Speed Transmit Speed: Display the data rate can be transferred to the server, the Wireless AP. Receive Speed: Display the data rate receives from the Wireless AP. Refresh: Click to manually refresh the data. Auto Reresh: Select a time interval to refresh the data automatically or none to disable the feature.
Device Configuration Status – DHCP Table / ARP Table / VRRP Status 36 BEC MX-210NP User Manual DHCP Table DHCP table displays the devices connected to the router with clear information. Index #: The numeric indicator for devices using dynamic IP addresses. Host Name: Display the hostname of the PC. IP Address: The IP allocated to the device. MAC Address: The MAC of the connected device. Expire Time: The total remaining interval since the IP assignment to the PC. ARP Table ARP (Address Resolution Protocol) table displays a mapping IP address with a PC’s MAC address. #: The numeric table list indicator. IP Address: It is the internal/local IP address to access to the network. MAC Address: The MAC address of a device, e.g. PC, notebook, printer, etc., that is corresponded with the IP address. VRRP Status Current Status: Display current VRRP status, Master or Backup. Current Master: Display the IP address of the Master
Device Configuration Quick Start 37 BEC MX-210NP User Manual Quick Start This is a useful and easy utility to help you to setup the router quickly and to connect to your ISP (Internet Service Provider) with only a few steps. It will guide you step by step to setup password, time zone, and WAN settings of your device. The Quick Start Wizard is a helpful guide for the first-time users to the device. For detailed instructions on configuring WAN settings, see refer to the Interface Setup section. Click NEXT to move on to Step 1. Step 1 – Password Set new password of the “admin” account to access for router management. The default is “admin”. Once changed, please use this new password next time when accessing to the router. Click NEXT to continue. Step 2 – Time Zone Choose your time zone. Click NEXT to continue.
Device Configuration Quick Start 38 BEC MX-210NP User Manual Step 3 – Wireless Set up your wireless connection if you want to connect to the Internet wirelessly on your PCs. Click NEXT to continue. Step 4 – ISP Connection Type Set up your Internet connection. Select an appropriate WAN connection protocol then click NEXT to continue. >> If selected 4G/LTE Input all relevant 4G/LTE parameters from your cellular provider. Click Next to continue.
Device Configuration Quick Start 39 BEC MX-210NP User Manual >> If selected EWAN (LAN2) / Static IP or PPPoE, enter the static IP address or PPPoE account information provided by your ISP. Click NEXT to continue. Step 4 – Quick Start Completed The Setup Wizard has completed. Click on BACK to make changes or correct mistakes. Click NEXT to save the current settings and complete the Quick Start setups. Go back to the Status > Device Info to view the status.
Device Configuration Interface Setup – Internet (4G/LTE) 40 BEC MX-210NP User Manual Device Configuration Interface Setup Here are the features under Interface Setup: Internet, LAN, Wireless, Wireless MAC Filter and Loopback Internet ❖ 4G/LTE WAN Interface: List all available WAN interfaces. (In this section, you have selected to use 4G/LTE) Status: Choose Activated to enable the 4G/LTE connection. Usage Allowance: Enable and click “Usage Allowance” for further setting configuration of your 4G/LTE data usage. Usage Allowance
Device Configuration Interface Setup – Internet (4G/LTE) 41 BEC MX-210NP User Manual Usage Allowance (Cont.) Mode: Include Volume-based and Time-based control.  Volume-based include “only Download”, "only Upload”, and “Download and Upload” to limit the flow.  Time-based control the flow by providing specific hours per month. The billing period begins on: the beginning day of billing each month. Over usage allowance action: Here are actions to perform when mobile data usage, defined in Mode, reached to its maximum.  None: No action taken  Disconnect: Disconnect mobile connection  Email Alert: Send an e-mail alert and keep the mobile connection alive.  Email Alert and Disconnect: Disconnect mobile connection after an alert e-mail is being sent. Save the statistics to ROM:  Every hour: Activate the 3G/4G-LTE statistics on data usage and this info will get updated and saved to the internal memory (ROM) in every hour. Once the feature is turned on, you can see the amount of data used and how many days left before next billing cycle starts. Go to Status >> 3G/4G-LTE Status page for details. NOTE: This statistic information will get deleted after a factory reset.  Disable: No action taken LTE Mode*: Display current selected LTE frequency band. To change the band, please click “LTE Mode” link to access to the band selection page. LTE Band LTE Band: A list of available LTE bands to choose from.
Device Configuration Interface Setup – Internet (4G/LTE) 42 BEC MX-210NP User Manual IP Pass-through Mode: When enabled, MX-210NP is in bridge mode that it does not obtain a WAN IP address; features such as routing capabilities, NAT, firewall, etc., are being disabled. The client router that is behind the MX-210NP now obtains a WAN IP address. When disabled, MX-210NP is in router mode that it handles a WAN IP address and all features become available. LTE Antenna Diversity *: When enabled, the auxiliary antenna will be activated. With disabled, only the primary antenna is receiving and transmitting data. To change it, please click “LTE Antenna Diversity” link to access to the selection page. LTE Antenna Diversity To enable or disable the LTE antenna diversity feature. * Feature is available with specific cellular module Network Mode: There are numbers of services to select from. If you are not sure which mode to use, you may select Automatic to auto detect the best mode for you. PLMN (Public Land Mobile Network) Selection: Either manually enter the information or click Scan button to scanning all closest base stations in the area. Dual APN *: Unit can support up to two (2) APNs. Select Single / Dual or a different LTE/3G APN.  APN (3G): If select LTE/3G with different APN, enter the APN here. * Feature is available with specific cellular module APN: An APN is like a URL on the WWW, it is what the unit makes a GPRS / UMTS call. The service provider can attach anything to an APN to create a data connection, requirements for APNs varies between different service providers. Most service providers have an internet portal which they use to connect to a DHCP Server, thus giving you access to the internet i.e. some 3G operators use the APN ‘internet’ for their portal. The default value is “internet”. PDN Type: The IP type for PDN connections. Available types are IPv4, IPv6, and IPv4v6. Authentication Protocol: Manually specify CHAP (Challenge Handshake Authentication Protocol) or PAP (Password Authentication Protocol). When using PAP, the password is sent unencrypted, while CHAP encrypts the password before sending, and also allows for challenges at different periods to ensure that an intruder has not replaced the client. Username/Password: Enter the username and password provided by your service provider. The username and password are case sensitive. PIN: PIN stands for Personal Identification Number. A PIN code is a numeric value used in certain systems as a password to gain access and authenticate. In mobile phones a PIN code locks the SIM card until you enter the correct code. If you enter the PIN code incorrectly into the phone 3 times in a row, then the SIM card will be blocked, and you will require a PUK code from your network/service provider.
Device Configuration Interface Setup – Internet (4G/LTE) 43 BEC MX-210NP User Manual Connection: Default set to Always on to keep an always-on 3G/4G-LTE connection. Keep Alive: Select Yes to keep the 3G/4G-LTE connection always on  Keep Alive IP: Manually enter the Keep Alive IP Address to be used for ping operation to check if the connection is still on.  Check Interval 5 x ___ Seconds: Default is set to 1 (5 seconds). Setup a timer to ping the keep alive IP. Default Route: Select Yes to use this interface as default route interface. NAT: Select this option to Disabled/Enable the NAT (Network Address Translation) function. Enable NAT to grant multiples devices in LAN to access to the Internet through a single WAN IP. When router’s Internet configuration is finished successfully, you can go to the Status to check connection information. MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) an IP attempts to send through the interface. 0 means to use default MTU size, 1500byte. Click Save to apply settings.
Device Configuration Interface Setup – Internet (EWAN) 44 BEC MX-210NP User Manual ❖ EWAN (LAN 2) Status: Select to enable/activate or disable/deactivated the service. IPv4/IPv6 IP Version: Choose IPv4, IPv4/IPv6, IPv6 based on your environment. If you don’t know which one to choose from, please choose IPv4/IPv6 instead.
Device Configuration Interface Setup – Internet (EWAN) 45 BEC MX-210NP User Manual ISP Connection Type: ISP: Select the encapsulation type your ISP uses.  Dynamic IP: Select this option if your ISP provides you an IP address automatically.  Static IP: Select this option to set static IP information. You will need to enter in the Connection type, IP address, subnet mask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form. IP address from by four IP octets separated by a dot (xx.xx.xx.xx). The Router will not accept the IP address if it is not in this format.  PPPoE: Select this option if your ISP requires you to use a PPPoE connection. 802.1q Options 802.1q: When activated, please enter a VLAN ID. VLAN ID: It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN ID identification, tagged: 0-4095. PPPoE (If selected PPPoE as WAN Connection Type; otherwise, skip this part) Username: Enter the user name provided by your ISP. Password: Enter the password provided by your ISP. Bridge Interface for PPPoE: When “Activated”, the device will gain WAN IP from your ISP with the PPPoE account. But if your PC is connected to the router working as a DHCP client, in this mode, the device acts as a NAT router; while if you dial up with the account within your PC, the device will then work as a bridge forwarding the PPPoE information to the PPPoE server and send the response to your PC, thus your PC gets a WAN IP working in the internet. Connection Setting Connection:  Always On: Click on Always On to establish a PPPoE session during start up and to automatically re-establish the PPPoE session when disconnected by the ISP.  Connect Manually: Select Connect Manually when you don't want the connection up all the time. TCP MSS Option: Enter the maximum size of the data that TCP can send in a segment. Maximum Segment Size (MSS). IP Options
Device Configuration Interface Setup – Internet (EWAN) 46 BEC MX-210NP User Manual IP Common Options Default Route: Select Yes to use this interface as default route interface. TCP MTU Option: Enter the maximum packet that can be transmitted. Default MTU 0 means it is set to 1492 bytes. IPv4 Options Get IP Address: Choose Static or Dynamic Static IP Address: If Static is selected in the above field, please enter the specific IP address you get from ISP and the following IP subnet mask and gateway address. IP Subnet Mask: The default is 0.0.0.0. User can change it to other such as 255.255.255.0.Type the subnet mask assigned to you by your ISP (if given). Gateway: Enter the specific gateway IP address you get from ISP. NAT: Enable to allow MX-210NP to assign private network IPs to all devices in the network for get Internet access. Dynamic Route:  RIP Version: (Routing Information protocol) Select this option to specify the RIP version, including RIP-1, RIP-2.  RIP Direction: Select this option to specify the RIP direction. - None is for disabling the RIP function. - Both means the router will periodically send routing information and accept routing information then incorporate into routing table. - IN only means the router will only accept but will not send RIP packet. - OUT only means the router will only send but will not accept RIP packet.
Device Configuration Interface Setup – Internet (EWAN) 47 BEC MX-210NP User Manual IGMP Proxy: IGMP (Internet Group Multicast Protocol) is a network-layer protocol used to establish membership in a Multicast group. Choose whether enable IGMP proxy. IPv6 options (only when choose IPv4/IPv6 or just IPv6 in IP version field above): IPv6 Address: Type the WAN IPv6 address from your ISP. Obtain IPv6 DNS: Choose if you want to obtain DNS automatically. Primary/Secondary: if you choose Disable in the Obtain IPv6 DNS field, please type the exactly primary and secondary DNS. MLD Proxy: MLD (Multicast Listener Discovery Protocol) is to IPv6 just as IGMP to IPv4. It is a Multicast Management protocol for IPv6 multicast packets. When router’s Internet configuration is finished successfully, you can go to status to get the connection information. Click Save to apply settings.
Device Configuration Interface Setup – LAN 48 BEC MX-210NP User Manual LAN A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building. IPv4 Parameters IP Address: Enter the IP address of Router in dotted decimal notation, for example, 192.168.1.254 (factory default). IP Subnet Mask: The default is 255.255.255.0. User can change it to other such as 255.255.255.128. Alias IP Address: This is for local networks virtual IP interface. Specify an IP address on this virtual interface. Alias IP Subnet Mask: Specify a subnet mask on this virtual interface. IGMP Snooping: Select Activated to enable IGMP Snooping function. Without the IGMP snooping, multicast traffic is treated in the same manner as broadcast traffic to be forwarded to all ports. With
Device Configuration Interface Setup – LAN 49 BEC MX-210NP User Manual IGMP snooping, multicast traffic of a group is only forwarded to ports that have members of that group. Dynamic Route: Select the RIP version from RIP1 or RIP2. DHCPv4 Server DHCP (Dynamic Host Configuration Protocol) allows individual clients to obtain TCP/IP configuration at start-up from a server. DHCPv4 Server: If set to Enabled, your MX-210NP can assign IP addresses, default gateway and DNS servers to the DHCP client.  If set to Disabled, the DHCP server will be disabled.  If set to Relay, the MX-210NP acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server field in this case.  When DHCP is used, the following items need to be set. Start IP: This field specifies the first of the contiguous addresses in the IP address pool. IP Pool Count: This field specifies the count of the IP address pool. Lease Time: The current lease time of client. Physical Ports: Select to determine if the DHCPv4 server is applicable to the specific port or ports. By default, all ports can obtain local IP from the DHCPv4 server. DNS Relay:  Select Automatic detection or  Manually specific Primary and Secondary DNS IP addresses Primary / Secondary DNS Server: Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP clients along with the IP address and the subnet mask. Option 66: Set the IP or hostname of the TFTP server for devices, like IPTV Set Box, to get configuration settings from the TFTP server. Option 160: Set the IP or hostname of the TFTP server for devices, like IPTV Set Box, to get configuration settings from the TFTP server. (The option 160 is an extended feature in DHCP option, similar to option 66, but using http or https protocols.)
Device Configuration Interface Setup – LAN 50 BEC MX-210NP User Manual Fixed Host In this field, users can map the specific IP (must in the DHCP IP pool) for some specific MAC, and this information can be listed in the following table. IP Address: Enter the specific IP. For example: 192.168.1.110. MAC Address: Enter the responding MAC. For example: 00:0A:F7:45:6D:ED When added, you can see the ones listed as showed below: IPv6 Parameters The IPv6 address composes of two parts, thus, the prefix and the interface ID. Interface Address / Prefix Length: Enter a static LAN IPv6 address. If you are not sure what to do with this field, please leave it empty as if contains false information it could result in LAN devices not being able to access other IPv6 device. Router will take the same WAN’s prefix to LAN side if the field is empty. DHCPv6 Server There are two methods to dynamically configure IPv6 address on hosts, Stateless and Stateful. Stateless auto-configuration requires no manual configuration of hosts, minimal (if any) configuration of routers, and no additional servers. The stateless mechanism allows a host to generate its own addresses using a combination of locally available information (MAC address) and information (prefix) advertised by routers. Routers advertise prefixes that identify the subnet(s) associated with a link, while hosts generate an "interface identifier" that uniquely identifies an interface on a subnet. An address is formed by combining the two. When using stateless configuration, you needn’t configure anything on the client. Stateful configuration, for example using DHCPv6 (which resembles its counterpart DHCP in IPv4.) In the stateful auto configuration model, hosts obtain interface addresses and/or configuration information and parameters from a DHCPv6 server. The Server maintains a database that keeps track of which addresses have been assigned to which hosts.
Device Configuration Interface Setup – LAN 51 BEC MX-210NP User Manual DHCPv6 Server: Check whether to enable DHCPv6 server. DHCPv6 Server Type: Select Stateless or Stateful. When DHCPv6 is enabled, this parameter is available.  Stateless: If selected, the PCs in LAN are configured through RA mode, thus, the PCs in LAN are configured through RA mode, to obtain the prefix message and generate an address using a combination of locally available information (MAC address) and information (prefix) advertised by routers, but they can obtain such information like DNS from DHCPv6 Server.  Stateful: If selected, the PCs in LAN will be configured like in IPv4 mode, thus obtain addresses and DNS information from DHCPv6 server. Start interface ID: enter the start interface ID. The IPv6 address composed of two parts, thus, the prefix and the interface ID. Interface is like the Host ID compared to IPv4. End interface ID: enter the end interface ID. Leased Time (seconds): the leased time, similar to leased time in DHCPv4, is a time limit assigned to clients, when expires, the assigned ID will be recycled and reassigned. Router Advertisement: Check to Enable or Disable the Issue Router Advertisement feature. This feature is to send Router Advertisement messages periodically which would multicast the IPv6 Prefix information (similar to v4 network number 192.168.1.0) to all LAN devices if the field is enabled. We suggest enabling this field. Click Save to apply settings.
Device Configuration Interface Setup – Wireless 52 BEC MX-210NP User Manual Wireless This section introduces the wireless LAN and some basic configurations. NOTE: WLAN1 / 2 / 3 / 4 Interface refers to as SSID1 / 2 / 3 / 4 Wi-Fi networks. Access Point Settings Site Servey: Click to view all other available Wireless-AP devices around the MX-210NP.  CH (Channel): Channel ID used.  SSID: The name of the wireless AP.  BSSID: The MaC address of the wireless AP.  Security: The security mode in the wireless AP.  Singal (%): Singal strength of the wireless AP. Signal incrases means the wireless AP is closer to your MX-210NP and may cause interferences. Access Point: Default setting is set to Activated. If you want to close the wireless interface, select Deactivated. AP MAC Address: The MAC address of wireless AP. Wireless Mode: The default setting is 802.11b+g+n (Mixed mode). If you do not know or have both 11g and 11b devices in your network, then keep the default in mixed mode. From the drop-down manual, you can select 802.11g if you have only 11g card. If you have only 11b card, then select 802.11b and if you only have 802.11n then select 802.11n. Channel: The range of radio frequencies used by IEEE 802.11b/g/n wireless devices is called a channel. There are Regulation Domains and Channel ID in this field. The Channel ID will be different based on Regulation Domains. Select a channel from the drop-down list box.
Device Configuration Interface Setup – Wireless 53 BEC MX-210NP User Manual Beacon interval: The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast by the Router to synchronize the wireless network. RTS/CTS Threshold: The RTS (Request To Send) threshold (number of bytes) for enabling RTS/CTS handshake. Data with its frame size larger than this value will perform the RTS/CTS handshake. Enter a value between 1500 and 2347. Fragmentation Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages. It is the maximum data fragment size that can be sent. Enter a value between 256 and 2346, even number only. DTIM Interval: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). TX Power: The transmission power of the antennas, ranging from 1-100, the higher the more powerful of the transmission performance. IGMP Snooping: Enable or disable the IGMP Snooping function for wireless. Without IGMP snooping, multicast traffic is treated in the same manner as broadcast traffic - that is, it is forwarded to all ports. With IGMP snooping, multicast traffic of a group is only forwarded to ports that have members of that group.” 11n Settings Channel Bandwidth: Select 20 MHz, 40 MHz, or 20/40 MHz for the channel bandwidth. The wider the Channel bandwidth the better the performance will be. Extension Channel (20/40 MHz only): Select either Auto or Above the control channel. Guard Interval: Select either 800nsec or Automatic for the guard interval. The guard interval is here to ensure that data transmission do not interfere with each other. It also prevents propagation delays, echoing and reflections. The shorter the Guard Interval, the better the performance will be. We recommend users to select Auto. MCS (Modulation and Coding Scheme): There are options 0~15 and AUTO to select from. AUTO is recommended. SSID Settings
Device Configuration Interface Setup – Wireless 54 BEC MX-210NP User Manual Available SSID: User can determine how many virtual SSIDs to be used. Default is 1, maximum is 4. SSID Index: Select the number of SSIDs you want to use; up to 4 SSIDs are available in the list.  SSID1 SSID known as wlan-ap1 Interface  SSID2 known as wlan-ap2Interface  SSID3 known as wlan-ap3 Interface  SSID4 known as wlan-ap4 Interface SSID: The SSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change the default wlan-ap to a unique ID name to the AP which is already built-in to the router’s wireless interface. Make sure your wireless clients have exactly the SSID as the device to get connected to your network. Broadcast SSID: Select Yes to make the SSID visible so a station can obtain the SSID through passive scanning. Select No to hide the SSID in so a station cannot obtain the SSID through passive scanning. Client Isolation: Enable by clicking Yes to prevent wireless clients communicating with other wireless clients. Security Settings Security Type: You can disable or enable wireless security for protecting wireless network. The default type of wireless security is OPEN and to allow all wireless stations to communicate with the access points without any data encryption. To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers secure data encryption, known as WEP and WPA. There are five alternatives to select from: WEP 64-bit, WEP 128-bit, WPA-PSK, WPA2-PSK, and Mixed WPA/WPA2-PSK. If you require high security for transmissions, please select WPA-PSK, WPA2-PSK or WPA/WPA2-PSK.  WEP WEP Authentication Method: WEP authentication method, there are two methods of authentication used, Open System authentication (OPENWEB) and Share Key authentication (SHAREDWEB). We suggest you select OPENWEB. Key 1 to Key 4: Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required for 64-bitWEP and 128-bitWEP respectively.
Device Configuration Interface Setup – Wireless 55 BEC MX-210NP User Manual If chose WEP 64-bit, then enter any 5 ASCII characters or 10 hexadecimal characters ("0-9", "A-F"). If chose WEP 128-bit, then enter 13 ASCII characters or 26 hexadecimal characters ("0-9", "A-F"). You must configure all four keys, but only one key can be activated at any one time. The default key is key 1. NOTE: WPS requires a higher level of security than WEP, 64bits or 128bits. Select WAP / WAP2 security when using WPS.  WPA-PSK / WPA2-PSK / Mixed WPA & WPA2 WPA Algorithms: TKIP (Temporal Key Integrity Protocol) or AES (Advanced Encryption System) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. Pre-Shared key: The key for network authentication. The input format should be 8-63 ASKII characters or 64 hexadecimal characters Key Renewal Interval: The time interval for changing the security key automatically between wireless client and AP. WDS Settings WDS (Wireless distributed system) is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed, just define the peer’s MAC of the connected AP. WDS Mode: select Activated to enable WDS feature and Deactivated to disable this feature. MAC Address: Enter the AP MAC addresses (in XX:XX:XX:XX:XX:XX format) of the peer connected AP. Click Save to apply the settings.
Device Configuration Interface Setup – Wireless MAC Filter 56 BEC MX-210NP User Manual Wireless MAC Filter The MAC filter screen allows you to configure the router to give exclusive access to up to 8 devices (Allow Association) or exclude up to 8 devices from accessing the router (Deny Association). Every Ethernet device has a unique MAC (Media Access Control) address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example, 00:AA:BB:00:00:02. You need to know the MAC address of the devices you wish to filter. SSID Index: Select the targeted SSID you want the MAC filter rules to apply to. Active: Select Activated to enable MAC address filtering. Action: Define the filter action for the list of MAC addresses in the MAC address filter table.  Select Deny to block access to the AP, MAC addresses not listed will be allowed to access the router.  Select Allow to permit access to the router, MAC addresses not listed will be denied access to the router. MAC Address: Enter the MAC addresses (in XX:XX:XX:XX:XX:XX format) of the wireless station that are allowed or denied access to the specified in these address fields. Click Save to apply the settings.
Device Configuration Interface Setup – Loopback 57 BEC MX-210NP User Manual Loopback Loopback interface is a widely known virtual interface, not the physical interface, on router and is highly robust and always up. The loopback interface has its own IP and subnet mask, often used for router management as Telnet management IP and involved in BGP as BGP Update-Source and OSPF as Router ID. IP Address: Enter a dedicated IP address for the loopback interface. IP Subnet Mask: Enter the subnet mask for the loopback interface. Click Save to apply settings.
Device Configuration Dual WAN – General Setting 58 BEC MX-210NP User Manual Dual WAN Dual WAN, is a feature to have two independent Internet connections connected concurrently, offers a reliable Internet connectivity and maximize bandwidth utilization for critical applications delivery. General Setting Mode: Select a mode then click Save to proceed.
Device Configuration Dual WAN – General Setting (Failover & Failback) 59 BEC MX-210NP User Manual ❖ Failover & Failback Auto failover/failback ensures always-online network connectivity. When primary WAN link (WAN1) fails, all traffic will switch over to the backup WAN (WAN2) seamlessly. Again, when the primary link is restored, traffic will be handled over from WAN2 to WAN1. WAN Port Service Detection Policy WAN1 (Primary): Choose a desired WAN as the primary WAN Link from the list. WAN2 (Backup): Choose a desired WAN as the backup WAN Link from the list. Keep Backup Interface Connected: Select the following option whether to keep the backup WAN (WAN2) interface connected to the Internet.  Disable: Inactivate this feature.  Always: Keep the backup WAN (WAN2) interface always connected to the Internet  By Signal Strength: Enable and initiate automatic backup WAN to connect to the Internet at all time until the RSRP / RSSI of primary WAN is greater than the Minimum RSRP / RSSI. ◼ Minimum RSRP / RSSI: Set a minimum requirement for RSRP and RSSI for the primary WAN. Value range from -111 ~ -5. 0 means don’t care/no need to check this value. NOTE: Both the RSRP and RSSI cannot be 0 at the same time. Connectivity Decision & Probe Cycle: Set a number of times and time in seconds to determine when to switch to the backup link (WAN2) when primary link (WAN1) fails and vice versa. Example, Auto failover takes place after straight 3 consecutive failures in every 30 seconds meaning all traffic will hand over to backup link (WAN2) after primary link fails to response in total of 90 seconds, 30 seconds for 3 consecutive failures. Note: Failover and Failback follow the same Connectivity Decision & Probe Cycle rule to failover from WAN1 to WAN2 or fallback from WAN2 to WAN1.
Device Configuration Dual WAN – General Setting (Failover & Failback) 60 BEC MX-210NP User Manual Failover/Fallback Rule Decisions: 1. Probe by Ping: Enable Ping to the gateway or an IP address  Gateway: Internal system will wait for responses to the pings from the gateway of the WAN.  Host: Internal system will wait for responses to the pings from a fixed IP address. 2. Probe by Signal Strength: Enable to measure the LTE signal strength  Minimum RSRP / RSSI: Set a minimum requirement for RSRP and RSSI for initiating automatic WAN failback or failover procedures. The valid range is from -111 ~ -5. 0 means don’t care/no need to check this value. NOTE: Both the RSRP and RSSI cannot be 0 at the same time. Click Save to apply settings.
Device Configuration Dual WAN – General Setting (Load Balance) 61 BEC MX-210NP User Manual ❖ Load Balance Load balance aggregates the bandwidth of the two WAN links to optimize traffic distribution. When primary link, WAN1, goes down, all traffic will be redirected to the backup, WAN2, to ensure service continuity. WAN Port Service Detection Policy WAN1 (Primary): Choose a desired WAN as the primary WAN Link from the list. WAN2 (Backup): Choose a desired WAN as the backup WAN Link from the list. Service Detection: Enable to detect WAN connectivity automatically. Connectivity Decision: Set a number of times and time in seconds to determine when to turn-off the Load Balancing service. Example, Disable Load Balance after straight 3 consecutive failures in every 30 seconds meaning all traffic will hand over to backup link (WAN2) after primary link fails to response in total of 90 seconds, 30 seconds for 3 consecutive failures. Probe Ping on WAN 1 / WAN2: Enable Ping to the gateway or an IP address  Gateway: Internal system will wait for responses to the pings from the gateway of the WAN.  Host: Internal system will wait for responses to the pings from a fixed IP address. Click Save to apply settings
Device Configuration Dual WAN – Outbound Load Balance 62 BEC MX-210NP User Manual Outbound Load Balance The connections are distributed over WAN1 and WAN2 so that it can utilize bandwidth of both WAN ports. With Outbound load balance, traffic may be routed to a faster link when one of the WAN links is slower or congested so that user gains better throughput and less delay. User can distribute outbound traffic based on Session Mechanism or IP Hash Mechanism. Base on Session Mechanism: Balance by Session (Round Robin): Automatically assign requests/traffics to each WAN interface based on real-time WAN traffic-handling capacity. OR Balance by Session weight: Manually Balance session traffic based on a weight ratio. Example: Session weight by 3:1 meaning forward 3 requests to WAN1 and 1 request to WAN2. Base on IP Hash Mechanism: Balance by weight: Use an IP hash to balance traffic based on a ratio. It is to guarantee requests from the same IP address get forward to the same WAN interface. Click Save to apply settings
Device Configuration Dual WAN – Protocol Binding 63 BEC MX-210NP User Manual Protocol Binding Protocol Binding lets you direct specific traffic to go out from a specific WAN port. Policies determine how specific types of internet traffic are routed, for example, traffic from a specific IP address is granted access to only one WAN port rather than using both of the WAN ports as with load balancing. Rule Index: The numeric rule indicator. The maximum entry is up to 16. Active: Click YES to activate the rule Bind Interface: The dedicated WAN interface that guarantees to handle this traffic request. Source IP Address: Enter the local network, known as source, IP address of the origin of a traffic/packet. 0.0.0.0 means any IP address in the network. Subnet Mask: Enter the subnet of the source network. Port Number: Enter the port number which defines the application. Destination IP Address: Enter the destination / remote WAN IP address where the traffic/packet is going to. Enter 0.0.0.0 if no need to route to a specific IP address Subnet Mask: Enter the subnet of the designation network. Port Number: Enter the port number which defines the application. DSCP: The DSCP value. Value Range from 0~64; 64 means any value/unspecified Protocol: Select a protocol, TCP, UDP, ICMP, to use for this traffic. Click Save to apply settings Example: All traffics from IP 192.168.1.100/255.255.255.0 with port 8080 will go through WAN1 interface.
Device Configuration Dual WAN – Protocol Binding 64 BEC MX-210NP User Manual The only time it would go through WAN2 interface is when WAN1 has no Internet connection.
Device Configuration Advanced Setup – Firewall 65 BEC MX-210NP User Manual Advanced Setup Advanced configuration features provide advanced features, including Firewall, Routing, NAT, VRRP, Static DNS, QoS, Time Schedule and Mail Alert for advanced users. Firewall Your router includes a firewall for helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet. Firewall: To automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.  Enabled: Activate your firewall function.  Disabled: Deactivate the firewall function. SPI: If you enabled SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side.  Enabled: Activate your SPI function.  Disabled: Deactivate the SPI function. Click Save to apply settings
Device Configuration Advanced Setup – Routing 66 BEC MX-210NP User Manual Routing This is static route feature. You are equipped with the capability to control the routing of all the traffic across your network. With each routing rule created, user can specifically assign the destination where the traffic will be routed to. Index #: The numeric route indicator. Destination IP Address: IP address of the destination network Subnet Mask: The subnet mask of destination network. Gateway IP Address: IP address of the gateway or existing interface that this route uses. Metric: It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15. Interface: Media/channel selected to append the route. Edit: Edit the route; this icon is not shown for system default route. Drop: Drop the route; this icon is not shown for system default route. Add Route Destination IP Address: This is the destination subnet IP address. Destination Subnet Mask: The subnet mask of destination network. Gateway IP Address or Interface: This is the gateway IP address or existing interface to which packets are to be forwarded. Metric: It represents the cost of transmission for routing purposes. The number need not be precise, but it must be between 1 and 15. Click Save to add this route
Device Configuration Advanced Setup – NAT 67 BEC MX-210NP User Manual NAT The NAT (Network Address Translation) feature transforms a private IP into a public IP, allowing multiple users to access the internet through a single IP account, sharing the single IP address. NAT break the originally envisioned model of IP end-to-end connectivity across the Internet, so NAT can cause problems where IPSec/ PPTP encryption is applied or some application layer protocols such as SIP phones are located behind a NAT. And NAT makes it difficult for systems behind a NAT to accept incoming communications. NAT Status: Enabled. (Disabled if WAN connection is in BRIDGE mode) ALG VPN Passthrough: VPN pass-through is a feature of routers which allows VPN client on a private network to establish outbound VPNs unhindered. SIP ALG: Enable the SIP ALG when SIP phone needs ALG to pass through the NAT. Disable the SIP ALG when SIP phone includes NAT-Traversal algorithm. DMZ / Virtual Server Interface: Select a WAN interface connection to allow external access to your internal network. Service Index: Associated to EWAN interface marking each EWAN service (0-7), to select which EWAN service the DMZ and Virtual server are applied to. Click DMZ or Virtual Server to move on to set the DMZ or Virtual Server parameters, which are represented in the following scenario.
Device Configuration Advanced Setup – NAT (DMZ) 68 BEC MX-210NP User Manual DMZ NOTE: This feature disables automatically if WAN connection is in BRIDGE mode or NAT is being turned OFF. The DMZ Host is a local computer which has all UDP and TCP ports exposed to the Internet. When setting an internal IP address as the DMZ Host, all incoming packets will be forwarded to this local host device. Packet filter or virtual server entries will take priority over forwarding internet packets to the DMZ host. DMZ for (via a WAN Interface): Allows outside network to connect in and communicate with internal LAN devices via a specific WAN interface. DMZ:  Enabled: Activate the DMZ function.  Disabled: Deactivate the DMZ function. DMZ Host IP Address: Give a static IP address to the DMZ Host when Enabled radio button is checked. Be aware that this IP will be exposed to the WAN/Internet. Click Save to apply settings Except Ports Except Ports: Bypass UDP or/and TCP ports, in the list, being forwarded to the DMZ host. Port: Enter port to be monitored. Protocol: Enter the protocol to be monitored. Description: Enter a description to this rule. Example: Skip port 80 (UDP/TCP) in the list. All Incoming request to access to port 80 (Web GUI) will be forwarded to the embedded HTTP server of MX-210NP instead of the DMZ host. Click Add to add an entry to the Except Listing.
Device Configuration Advanced Setup – NAT (Virtual Server) 69 BEC MX-210NP User Manual Virtual Server NOTE: This feature disables automatically if WAN connection is in BRIDGE mode or NAT is being turned OFF. Virtual Server is also known as Port Forwarding that allows MX-210NP to direct incoming traffic to a specific device in the network. Configure a virtual rule in MX-210NP for remote users accessing services such as Web or FTP services via the public (WAN) IP address that can be automatically redirected to local servers in the LAN network. Depending on the requested service (TCP/UDP port number), the device redirects the external service request to the appropriate server within the LAN network. Virtual Server for: Indicate the related WAN interface to allow outside network to communicate with the internal LAN device. Protocol: Choose the application protocol. Start / End Port Number: Enter a port or port range you want to forward. (Example: Start / End: 1000 or Start: 1000 & End: 2000). The starting port must be greater than zero (0). The end port must be greater than or equal to the start port. Local IP Address: Enter the server IP address in the network to receive the traffic/packets. Start / End Port Number (Local): Enter the start / end port number of the local application (service).
Device Configuration Advanced Setup – NAT (Virtual Server) 70 BEC MX-210NP User Manual Examples of well-known and registered port numbers are shown below. For further information, please see IANA’s website at http://www.iana.org/assignments/port-numbers Well-known and Registered Ports Port Number Protocol Description 21 TCP FTP Control 22 TCP & UDP SSH Remote Login Protocol 23 TCP Telnet 25 TCP SMTP (Simple Mail Transfer Protocol) 53 TCP & UDP DNS (Domain Name Server) 69 UDP TFTP (Trivial File Transfer Protocol) 80 TCP World Wide Web HTTP 110 TCP POP3 (Post Office Protocol Version 3) 443 TCP & UDP HTTPS 1503 TCP T.120 1720 TCP H.323 7070 UDP RealAudio Using port forwarding does have security implications, as outside users will be able to connect to PCs on your network. For this reason you are advised to use specific Virtual Server entries just for the ports your application requires, instead of using DMZ. As doing so will result in all connections from the WAN attempt to access to your public IP of the DMZ PC specified. If you have disabled the NAT option in the WAN-ISP section, the Virtual Server function will hence be invalid. If the DHCP server option is enabled, you have to be very careful in assigning the IP addresses of the virtual servers in order to avoid conflicts. The easiest way of configuring Virtual Servers is to manually assign static IP address to each virtual server PC, with an address that does not fall into the range of IP addresses that are to be issued by the DHCP server. You can configure the virtual server IP address manually, but it must still be in the same subnet as the router. Attention
Device Configuration Advanced Setup – NAT (Example) 71 BEC MX-210NP User Manual Example: How to setup Port Forwarding for port 21 (FTP server) If you have a FTP server in your LAN network and want others to access it through WAN. Step 1: Assign a static IP to your local computer that is hosting the FTP server. Step 2: Login to the Gateway and go to Configuration / Advanced Setup / NAT / Virtual Server. FTP server uses TCP protocol with port 21. Enter "21” to Start and End Port Number. The MX-210NP will accept port 21 requests from WAN side. Enter the static IP assigned to the local PC that is hosting the FTP server. Ex: 192.168.1.102 Enter "21” to Local Start and End Port number. The MX-210NP will forward port 21 request from WAN to the specific LAN PC (Example: 192.168.1.102) in the network. Step 3: Click Save to save settings.
Device Configuration Advanced Setup – VRRP 72 BEC MX-210NP User Manual VRRP VRRP is designed to eliminate the single point of failure inherent in the static default routed environment. VRRP specifies an election protocol that dynamically assigns responsibility for a virtual router to one of the VRRP routers in a LAN. The VRRP router controlling the IP address associated with a virtual router is called the Master, and forwards packets sent to these IP addresses. The election process provides dynamic fail-over in the forwarding responsibility should the Master become unavailable. Any of the virtual router's IP addresses in a LAN can then be used as the default first hop router by end-hosts. The advantage gained from using VRRP is a higher availability default path without requiring configuration of dynamic routing or router discovery protocols on every end-host. VRRP: Click to activate the feature. VRID: Virtual Router Identifier, range from 1-255 (decimal). A master or backup router running the VRRP protocol may participate in one VRID instance. Priority: Specifies the sending VRRP router's priority for the virtual router. Higher values equal higher priority. The priority value for the VRRP router that owns the IP address associated with the virtual router MUST be 255. VRRP routers backing up a virtual router MUST use priority values between 1 and 254. The default priority value for VRRP routers backing up a virtual router is 100. The priority value zero (0) has special meaning indicating that the current Master has stopped participating in VRRP. This is used to trigger Backup routers to quickly transition to Master without having to wait for the current Master to timeout. Preempt Mode: When preempt mode is activated, a backup router always takes over the responsibility of the master router. When deactivated, the lower priority backup is left in the master state. VRIP: An IP address which is associated with the virtual router. Advertisement period: Indicates the time interval in seconds between advertisements. Default in 1 second. Click Save to apply settings.
Device Configuration Advanced Setup – Static DNS 73 BEC MX-210NP User Manual Static DNS The Domain Name System (DNS) is a hierarchical naming system built on a distributed database for computers, services, or any resource connected to the Internet or a private network associates various information with domain names assigned to each of the participating entities. Most importantly, it translates domain names meaningful to humans into the numerical identifiers associated with networking equipment for locating and addressing these devices worldwide. An often-used analogy to explain the Domain Name System is that it serves as the phone book for the Internet by translating human-friendly computer hostnames into IP addresses. For example, the domain name www.example.com can be translated into the addresses 192.0.32.10 (IPv4). IP Address: The IP address you are going to give a specific domain name. Domain Name: The friendly domain name for the IP address. Click Save to apply settings.
Device Configuration Advanced Setup – QoS 74 BEC MX-210NP User Manual QoS QoS helps you control the upload traffic of each application from LAN (Ethernet and/or Wireless) to WAN (Internet). It facilitates you the features to control the quality of throughput for each application. This is useful when there on certain types of data you want giver higher priority to, such as voice data packets given higher priority than web data packets. SW QoS: Select Activate to enable the QoS LAN to WAN (Bandwidth): You want to control the traffic from local network to the outside (Upstream). You can assign the priority for the application or you can limit the rate of the application. Eg: you have a FTP server inside the local network, and you want to have a limited control by the QoS policy and so you need to add a policy with LAN to WAN direction setting. WAN to LAN (Bandwidth): Control traffic from WAN to LAN (Downstream). Click Bandwidth Save to save settings. Rule Index: Index marking for each rule up to maximum of 16.  WAN Interface: Select a WAN interface connection to allow external access to your internal network.  Application: Assign a name that identifies the new QoS application rule. Select from the list box for quick setup. Direction: Shows the direction mode of the QoS application
Device Configuration Advanced Setup – QoS 75 BEC MX-210NP User Manual  Protocol: Select a protocol from the drop down list  DSCP Marking: Differentiated Services Code Point (DSCP), it is the first 6 bits in the ToS byte. DSCP Marking allows users to classify the traffic of the application to be executed according to the DSCP value. Rate Type: Choose Limited (Maximum) or Guaranteed (Minimum) to specify the date rate is allowed for this policy.  Rate: Specify the date rate in Kbps.  Priority: Set the priority given to each policy/application. Specify the priority for the use of bandwidth. You can specify which application can have higher priority to acquire the bandwidth. Its default setting is set to High. You may adjust this setting to fit your policy / application. Internal IP Address: The IP address values for Local LAN devices you want to give control.  Internal Port: The Port number on the LAN side, it is used to identify an application. External IP Address: The IP address on remote / WAN side.  External Port: The Port number on the remote / WAN side. Click Save to apply settings. To Remove a Policy: Simply select the Index then hit the Delete button to remove from the list.
Device Configuration Advanced Setup – Time Schedule 76 BEC MX-210NP User Manual Time Schedule The Time Schedule supports up to 16 timeslots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of the Internet by users or applications. This Time Schedule correlates closely with router’s time, since router does not have a real time clock on board; it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server from the Internet. Time Index: The rule indicator (0-15) for identifying each timeslot. Name: User-defined identification for each time period. Day of Week: Mon. to Sun. Specify the time interval for each timeslot from “Day of Week”. Start Time: The starting point of the interval for the timeslot, anytime in 00:00 – 24:00. End Time: The ending point of the interval for the timeslot, anytime in 00:00 – 24:00. Click Save to apply your settings. Example, you can add a timeslot named “TimeSlot1” which features a period from 9:00 of Monday to 18:00 of Tuesday. Another TimeSlot2 spanning from 09:00 to 18:00 of Wednesday
Device Configuration Advanced Setup – Mail Alert 77 BEC MX-210NP User Manual Mail Alert Mail alert is designed to keep system administrator or other relevant personnel alerted of any unexpected events that might have occurred to the network computers or server for monitoring efficiency. With this alert system, appropriate solutions may be tackled to fix problems that may have arisen so that the server can be properly maintained. Server Information SMTP Server: Enter the SMTP server that you would like to use for sending emails. Username: Enter the username of your email account to be used by the SMTP server. Password: Enter the password of your email account. Sender’s Email: Enter your email address. SSL/TLS: Check to whether to enable SSL encryption feature. Port: the port, default is 25. Account Test: Click the button to test the connectivity and feasibility to your sender’s e-mail. WAN IP Change Alert Recipient’s Email (WAN IP Change Alert): Enter a valid e-mail address to receive an alert message when WAN IP change has been detected. Recipient’s Email (3G/4G-LTE Usage Allowance): Enter a valid e-mail address to receive an alert message when the cellular data is over the Usage Allowance. Click Apply button to save settings
Device Configuration Access Management – Device Management 78 BEC MX-210NP User Manual Access Management Device Management Device Host Name Host Name: Enter the host name of the router. Default is home.gateway Embedded Web Server HTTP Port: It is the embedded web server (Web GUI) accessing port, default is 80. It can be changed other port other than port 80, e.g. port 8080. HTTPS Port: Similar to HTTP which is an unencrypted communication using port 80. HTTPS is encrypted by SSL using port 443 instead. HTTPS Server Certificate Index: HTTPS known as HTTP-over-SSL tunnel protocol. Select a certificate to identify the system web server. When accessing to the web server (Web GUI), the browser will issue a warning page. To import certificates, go to Maintenance >> Certificate Management to upload files. Otherwise, select Default certificate and CA. Click Save to apply settings.
Device Configuration Access Management – SNMP 79 BEC MX-210NP User Manual SNMP Simple Network Management Protocol (SNMP) is a protocol used for exchanging management information between network devices. The MX-210NP serves as a SNMP agent that allows a manager station to manage and monitor the router through the network. SNMP: Activate to enable SNMP. Get Community: Type the Get Community, which is the password for the incoming Get-and-GetNext requests from the management station. Set Community: Type the Set Community, which is the password for incoming Set requests from the management station. Trap Manager IP: Enter the IP of the server receiving the trap message (when some exception occurs) sent by this SNMP agent. System Name / Location / Contact: String descriptions of the SNMP agent. Interface: Select the access interface. Choices are LAN or ALL (Both LAN and WAN). SNMPv3 SNMPv3: Enable to activate the SNMPv3. User Name: Enter the name allowed to access the SNMP agent. Access Permissions: Set the access permissions for the user; RO--read only and RW--read and writer. Authentication Protocol: Select the authentication protocol, MD5 and SHA. SNMP agent can
Device Configuration Access Management – SNMP 80 BEC MX-210NP User Manual communicate with the manager station through authentication and encryption to secure the message exchange. Set the authentication and encryption information here and below. Authentication Key: Set the authentication key, 8-31 characters. Privacy Protocol: Select the privacy mode, DES and AES. Privacy Key: Set the privacy key, 8-31 characters. Click Save to apply settings.
Device Configuration Access Management – Syslog 81 BEC MX-210NP User Manual Syslog Use the Syslog to collect system event information to a remote log server. Remote System Log: Select Activated to enable this feature Server IP Address: Assign the remote log server IP address. Server UDP Port: Assign the remote log server port, 514 is commonly used. Click Save to apply settings.
Device Configuration Access Management – UPnP 82 BEC MX-210NP User Manual Universal Plug & Play UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device. Both the user’s Operating System and the relevant application must support UPnP in addition to the router. UPnP: Select this checkbox to activate UPnP. Be aware that anyone could use an UPnP application to open the web configuration’s login screen without entering the MX-210NP's IP address Auto-configured: Select this check box to allow UPnP-enabled applications to automatically configure the MX-210NP so that they can communicate through the MX-210NP, for example by using NAT traversal, UPnP applications automatically reserve a NAT forwarding port in order to communicate with another UPnP enabled device; this eliminates the need to manually configure port forwarding for the UPnP enabled application. Click Save to apply settings.
Device Configuration Access Management – DDNS 83 BEC MX-210NP User Manual Dynamic DNS (DDNS) The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your internet connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP. Here users can register different WAN interfaces with different DNS Providers. If you do not have a DDNS account, please choose a DDNS Service Provider from the list then go to their website to create an account first. Dynamic DNS: Select this check box to activate Dynamic DNS. Service Provider: Select from drop-down menu for the appropriate service provider, for example: www.dyndns.org. My Host Name: Type the domain name assigned to your MX-210NP by your Dynamic DNS provider. Username / Password: Enter the user name and password of the account you created with this service provider. Wildcard support: Select this check box to enable DYNDNS Wildcard. Period: Setup a time on how often the MX-210NP will update the DDNS server with your current external IP address. Click Save to apply settings.
Device Configuration Access Management – DDNS (Example) 84 BEC MX-210NP User Manual Example: How to register a DDNS account If you do not have an account with Dynamic DNS, please go to www.dyndns.org to register an account first. User test1 register a Dynamic Domain Names in DDNS provider http://www.dyndns.org/ . DDNS: www.hometest.com using username/password test/test
Device Configuration Access Management – Access Control 85 BEC MX-210NP User Manual Access Control Access Control Listing allows you to determine which services/protocols can access the MX-210NP interface from which computers. It is a management tool aimed to allow IPs (set in secure IP address) to access specified embedded applications (Web, etc., user can set) through some specified interface (LAN, WAN or both). User can have an elaborate understanding in the examples below. The maximum number of entry is 16. Access Control: Select whether to make Access Control function available. Rule Index: The numeric rule indicator. Active: Yes to activate the rule. Secure IP Address: The default 0.0.0.0 allows any client to use this service to manage the MX-210NP. Type an IP address range to restrict access to the client(s) without a matching IP address. Application: Choose a service that you want to all access to all the secure IP clients. The drop-down menu lists all the common used applications. Interface: Select the access interface. Choices are LAN, WAN, GRE and ALL. Click Save to apply settings. By default, the “Access Control” has two default rules. Default Rule 1: (Index 1), a rule to allow only clients from LAN to have access to all embedded applications (Web, FTP, etc.). Under this situation, clients from WAN cannot access the router even from Ping.
Device Configuration Access Management – Access Control 86 BEC MX-210NP User Manual Default Rule 2: (Index 2), an ACL rule to open Ping to WAN side.
Device Configuration Access Management – Packet Filter (IP & MAC Filter) 87 BEC MX-210NP User Manual Packet Filter You can filter the packages by MAC address, IP address, Protocol, Port number and Application or URL. ❖ Filter Type - IP & MAC Filter IP & MAC Filter Editing Rule Index: The numeric rule indicator. Individual Active: Yes to enable the rule. Action: This is how to deal with the packets matching the rule. Allow please select White List or Black selecting Black List. Interface: Select to determine which interface the rule will be applied to. Direction: Select to determine whether the rule applies to outgoing packets, incoming packets or packets of both directions. Type: Choose type of field you want to specify to monitor. Select “IPv4” for IPv4 address, port number and protocol. Select “IPv6” for IPv6 address, port number and protocol. Select “MAC” for MAC address.
Device Configuration Access Management – Packet Filter (IP & MAC Filter) 88 BEC MX-210NP User Manual  IPv4 Source IP Address: The source IP address of packets to be monitored. 0.0.0.0 means “Don’t care”. Source Subnet Mask: Enter the subnet mask of the source network. Source Port Number: The source port number of packets to be monitored. 0 means “Don’t care”. Destination IP Address: The destination IP address of packets to be monitored. 0.0.0.0 means “Don’t care”. Destination Subnet Mask: Enter the subnet mask of the destination network. Destination Port Number: This is the Port that defines the application. (E.g. HTTP is port 80.) DSCP: DSCP: Differentiated Services Code Point, it is recommended that this option be configured by an advanced user or keep 0. (0 means Don’t care.) Protocol: Specify the packet type (TCP, UDP, ICMP, and ICMPv6) that the rule applies to.  IPv6 Source IP (IPv6) Address/ Prefix: The source IP address or range of packets to be monitored. Source Port Number: The source port number of packets to be monitored. Destination IP (IPv6) Address/ Prefix: The destination subnet IP address. Destination Port Number: This is the Port or Port Ranges that defines the application. DSCP: show the set DSCP. Protocol: It is the packet protocol type used by the application. Select either TCP or UDP or
Device Configuration Access Management – Packet Filter (IP & MAC Filter) 89 BEC MX-210NP User Manual ICMP or ICMPv6  MAC Source MAC Address: show the MAC address of the rule applied. Time Schedule: Select a TimeSlot to activate the rule. Go to Time Schedule to configure a time control first. Click Save to apply settings.
Device Configuration Access Management – Packet Filter (URL Filter) 90 BEC MX-210NP User Manual ❖ Filter Type- URL Filter URL Filter: Select Activated to enable URL Filter. URL Filter Rule Index: The numeric rule indicator. Individual Active: To give control to the specific URL access individually, for example, you want to prohibit access to www.yahoo.com, please first press Activated in “URL Filter” field, and also Yes in “Individual Active” field; if some time you want to allow access to this URL, you simply select No in individual active field. In a word, the command serves as a switch to the access of some specific URL with the filter on. URL (Host): Specified URL which is prohibited from accessing. Time Schedule: Select a TimeSlot to activate the rule. Go to Time Schedule to configure a time control first. Click Save to apply settings.
Device Configuration Access Management – CWMP (TR-069) 91 BEC MX-210NP User Manual CWMP (TR-069) CWMP, short for CPE WAN Management Protocol, also called TR069 is a Broadband Forum technical specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer protocol for remote management of end-user devices. It defines an application layer protocol for remote management of end-user devices. As a bidirectional SOAP/HTTP based protocol it can provides the communication between customer premises equipment (CPE) and Auto Configuration Server (ACS). It includes both a safe configuration and the control of other CPE management functions within an integrated framework. In the course of the booming broadband market, the number of different internet access possibilities grew as well (e.g. modems, routers, gateways, set-top box, VoIP-phones).At the same time the configuration of this equipment became more complicated –too complicated for end-users. For this reason, TR-069 was developed. It provides the possibility of auto configuration of the access types. Using TR-069 the terminals can get in contact with the Auto Configuration Servers (ACS) and establish the configuration automatically and let ACS configure CPE automatically. CWMP: Select activated to enable CWMP. ACS Login Information URL: Enter the ACS server login URL. User Name: Specify the ACS User Name for ACS authentication to the connection from CPE. Password: Enter the ACS server login password. Connection Request Information
Device Configuration Access Management – CWMP (TR-069) 92 BEC MX-210NP User Manual Path: Local path in HTTP URL for an ACS to make a Connection Request notification to the CPE. Username: Username used to authenticate an ACS making a Connection Request to the CPE. Password: Password used to authenticate an ACS making a Connection Request to the CPE. Periodic Inform Config Periodic Inform: Select Activated to authorize the router to send an Inform message to the ACS automatically. Interval(s): Specify the inform interval time (sec) which CPE used to periodically send inform message to automatically connect to ACS. When the inform interval time arrives, the CPE will send inform message to automatically connect to ACS. Bind WAN Interface Interface: Specify any available or a single WAN interface to handle TR-069 requests. NATT Config - This is a proprietary feature provided by BEC. May leave them in blank, no configuration is required. NATT Server: By BEC administrator only. NATT Period: By BEC administrator only. Click Save to apply settings.
Device Configuration Access Management – Parental Control 93 BEC MX-210NP User Manual Parental Control This feature provides Web content filtering offering safer and more reliable web surfing for users especially for parents to protect network security and control the contents for children at home. To activate this feature, please log on to www.opendns.com to get an OpenDNS account first. Parent Control Provider: Hosted by www.opendns.com Parent Control: Enable the feature by clicking the Activated Host Name: It is the domain name of your OpenDNS. If you don’t have one, please leave it blink. Username / Password: Put down your OpenDNS account username and password Click Save to apply settings.
Device Configuration Access Management – BECentral Management 94 BEC MX-210NP User Manual BECentral Management BECentral is a cloud-based device management platform that provides operators with a comprehensive suite of services to manage devices in real-time. BECentral Management: Activate to enable the feature. BECentral Management URL: Access path to the BECentral. BECentral Management Port: Port listened by the BECentral. Organization ID: Customer ID (By BE C administrator only) Tag ID: By BEC administrator only. Device Report Interval: Enter the interval time in seconds to send inform message periodically to the BECentral. Interface: Specify any available or a single WAN interface to handle BECentral requests.
Device Configuration Maintenance – User Management 95 BEC MX-210NP User Manual Maintenance User Management User Management provides the Administrator with the ability to grant access control and manage GUI login credentials for each user. There are two access management levels, Administrator and User. The default root account, Administrator (admin), has full access to all the features listed and ability to create other accounts with features to allow other users to access to. The User account is with limited access (specified by advanced users with admin account) to the GUI. Total of 8 accounts can be created to grant access to manage the MX-210NP via the web page. ❖ Administrator Account admin/admin is the root/default account username and password. NOTE: This username / password may vary by different Internet Service Providers. Login using the Administrator account, you will have the full accessibility to manage & control your gateway device and can also create user accounts for others to control some of the open configuration settings. User Setup Index: The numeric account indicator. The maximum entry is up to 8 accounts. User Name: Create account(s) user name for GUI management. New Password: Enter a new password for this user account. Confirmed Password: Re-enter the new password again; you must enter the password exactly the same as in the previous field
Device Configuration Maintenance – User Management (Other Account) 96 BEC MX-210NP User Manual ❖ Other Account User Account Setup Index #: The numeric account indicator. The maximum entry is up to 8. Username: Create account(s) user name for GUI management. New Password: Password for the user account. Confirm Password: Re-enter the password. Web GUI Permission Guest Account: Enable to create this new guest account. Interface Setup / Advanced Setup / VPN Setup / Access Management / Maintenance: Enable to grant this user access to these features. When someone accesses to the MX-210NP using this “user” account, he/she can only manage and configure the features that is pre-selected in Web GUI Permission for this account. Click Save to apply settings.
Device Configuration Maintenance – Certificate Management 97 BEC MX-210NP User Manual Certificate Management This feature is used for OpenVPN and HTTS Server authentication of the device using certificate. If the imported certificate doesn't match the authorized certificate with the Server then no access is allowed. Edit: Click (Edit) to import a certificate. Delete: Click (Delete) to remove the certificate from the list. Local Certificate Listing Index #: The numeric account indicator. The maximum entry is up to 2. Certificate Name: Description of the certificate. PKCS12: Every certificate is accompanied by a private key. Upload both files if PKCS is disabled. Enable PKCS12 to put Certificate & Private Key in the same file, like *.p12, *.pfx. Certificate File: Browse to locate the target certificate file on PC before uploading it. Private Key File: Browse to locate the target file on PC before uploading it. If PKCS enabled, please ignore this setting. Password: Enter the password if any, which is used to protect the private key. Otherwise, leave it empty. Click Apply to save settings.
Device Configuration Maintenance – Certificate Management 98 BEC MX-210NP User Manual Trusted CA Listing Index #: The numeric account indicator. The maximum entry is up to 2. CA Name: Description of the CA. CA Certificate File: Browse to locate the target certificate file on PC before uploading it. Click Apply to save settings.
Device Configuration Maintenance – Time Zone 99 BEC MX-210NP User Manual Time Zone With default, MX-210NP does not contain the correct local time and date. There are several options to setup, maintain, and configure current local time/date on the MX-210NP. If you plan to use Time Schedule feature, it is extremely important you set up the Time Zone correctly. Synchronize time with: Select the methods to synchronize the time.  NTP Server automatically: To synchronize time with the SNTP servers to get the current time from an SNTP server outside your network then choose your local time zone. After a successful connection to the Internet, MX-210NP will retrieve the correct local time from the SNTP server this is specified.  PC’s Clock: To synchronize time with the PC’s clock.  Manually: Select this to enter the SNMP server IP address manually. ◆ Date: Month / Date / Year. Month – 1 ~ 12 (January ~ December). ◆ Time: Hour: Minute: Second Time Zone: Choose the time zone of your location. This will set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Saving: Select this option if you use daylight savings time. NTP Server Address: Enter the IP address of your time server. Check with your ISP/network administrator if you are unsure of this information. Click Save to apply settings.
Device Configuration Maintenance – Firmware & Configuration 100 BEC MX-210NP User Manual Firmware & Configuration Firmware is the software that controls the hardware and provides all functionalities which are available in the GUI. This software may be improved and/or modified; your MX-210NP provides an effortless way to update the code to take advantage of the changes. To upgrade the firmware of the MX-210NP, you should download or copy the firmware to your local environment first. Click “Choose File” to specify the path of the firmware file. Then, click “Upgrade” to start upgrading process. After completing the firmware upgrade, the MX-210NP will automatically restart and run the new firmware. Upgrade: Choose Firmware or Configuration you want to update. System Restart with:  Current Settings: Restart the device with the current settings automatically when finishing upgrading.  Factory Default Settings: Restart the device with factory default settings automatically when finishing upgrading. File: Type in the location of the file you want to upload in this field or click Browse to find it. Choose File: Click “Choose File” to find the configuration file or firmware file you want to upload. Remember that you must extract / decompress / unzip the .zip files before you can upload them. Backup Configuration: Click Backup button to back up the current running configuration file and save it to your computer if you need this configuration file to be restored back to your MX-210NP device when making false configurations and want to restore to the original settings. Upgrade: Click “Upgrade” to begin the upload process. This process may take up to two minutes. DO NOT turn off or power cycle the device while firmware upgrading is still in process. Improper operation could damage your MX-210NP.
Device Configuration Maintenance – System Restart 101 BEC MX-210NP User Manual System Restart Click System Restart with option Current Settings to reboot your router. If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to restore to factory default settings. You may also restore your router to factory settings by holding the small Reset pinhole button on the back of your router in about more than 6s seconds whilst the router is turned on.
Device Configuration Maintenance – Auto Reboot 102 BEC MX-210NP User Manual Auto Reboot Schedule an automatic reboot for your MX-210NP to ensure proper operation and best performance. This reboot will only reboot with current configuration settings and not overwrite any existing settings. Click Save to apply settings Example: Schedule MX-210NP to reboot at 10:00pm (22:00) every weekday (Monday thru Friday) and reboot at 9:00am on Saturday and Sunday.
Device Configuration Maintenance – Diagnostic Test 103 BEC MX-210NP User Manual Diagnostics Tool The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides. 4G-LTE / EWAN (LAN2) Ping other IP Address: Click Yes if you wish to ping other IP address rather than google.com Click START to begin to diagnose the connection. Speed Time: Measure the current uplink and downlink speed rate.  Take less than a minute to run the test.  Result in Uplink / Downlink Click Back to go back to the Diagnostic Tool
Device Configuration Maintenance – Diagnostic Test 104 BEC MX-210NP User Manual Trace Route is to display how many hops (also view the exact hops) required to get to the destination. Click Yes, enter the IP address or domain then Start Trace Route. IP Address or Domain: Set the destination host (IP, domain name) to be traced. Max TTL value: Set the max Time to live (TTL) value. Shown as we “trace” www.billion.com below. LAN Ping other IP Address: Click Yes to ping any desired IP address or a domain. Speed Time: Measure the current uplink and downlink speed rate.  Take less than a minute to run the test.  Result in Uplink / Downlink
Device Configuration Maintenance – Diagnostic Test 105 BEC MX-210NP User Manual Click Back to go back to the Diagnostic Tool Click START to begin to diagnose the connection.
Troubleshooting 106 BEC MX-210NP User Manual Chapter 5: Troubleshooting If your MX-210NP is not functioning properly, you can refer to this chapter for simple troubleshooting before contacting your service provider support. This can save you time and effort but if symptoms persist, consult your service provider. Problems with the Router Problem Suggested Action None of the LEDs is on when you turn on the router Check the connection between the router and the adapter. If the problem persists, most likely it is due to the malfunction of your hardware. Please contact your service provider or BEC for technical support. You have forgotten your login username or password Try the default username "admin" and password "admin". If this fails, you can restore your router to its factory settings by pressing the reset button on the device rear side. Problem with LAN Interface Problem Suggested Action Cannot PING any PC on LAN Check the Ethernet LEDs on the front panel. The LED should be on for the port that has a PC connected. If it does not lit, check to see if the cable between your router and the PC is properly connected. Make sure you have first uninstalled your firewall program before troubleshooting. Verify that the IP address and the subnet mask are consistent for both the router and the workstations.
Troubleshooting 107 BEC MX-210NP User Manual Recovery Procedures Problem Suggested Action 1. The front LEDs display incorrectly upgrade 2. Still cannot access to the router management interface after pressing the RESET button. 3. Software / Firmware upgrade failure Before starting recovery process, please configure the IP address of the PC as 192.168.1.100 and proceed with the following step-by-step guide. 1. Power the router off. 2. Press reset button and power on the router, once the Power Lights Red, keeping press reset button over 6 seconds. 3. Internet LED flashes Green, router entering recovery procedure and router's IP will reset to Emergency IP address (Say 192.168.1.1). 4. Open browser and access http://192.168.1.1 to upload the firmware. 5. Internet LED lit Red, and router starts to write firmware into flash. Please DO NOT power off the router at this step. 6. Internet LED lit Green when successfully upgrade firmware. 7. Power cycle off/on the MX-210NP
Appendix 108 BEC MX-210NP User Manual APPENDIX: PRODUCT SUPPORT & CONTACT If you come across any problems please contact the dealer from where you have purchased the product. Contact BEC @ http://www.bectechnologies.net MAC OS is a registered Trademark of Apple Computer, Inc. Windows 10/8/7 are registered Trademarks of Microsoft Corporation
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. . This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This radio transmitter FCCID: QI3BIL-MX210NP has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 Cortec AN0727-64DP5BSM Dipole Antenna 0.28 dBi for LTE Band12

Navigation menu