Bio Medical Devices BASE2010 User Manual 38610
Bio-Medical Devices, Inc. 38610
8
PRODUCT MARKETING CONFIDENTIAL 04/20/99 — _ FCC m: OGQ-BASEZOlO INSTRUCTION MANUAL C OMMchoice2000’m Communication System > > > > > > > > > > > > >inslruction manual A product of Bio-Medical Devices, inc. 1 800 44 DEVICES PRODUCT MARKETING CONFIDENTlAL 04/20/99 COMMcholcezooo TMCOMMUNICATION SYSTEM OPERATION/SERVICE MANUAL The COWchoicej‘aW “‘ Communication System was intended for small to medium communication areas, such as: 0 warehouses; 0 hospital operating rooms (where tlte system compliments sterile ventilation systems [hoods and drapes] worn during operations); 0 recreational sporting events like paint ball games; and 0 other close local proximity applications, the COMMcholcej‘W" Communication System consists of: 0 six (6) MOBILE TRANSCEIVE‘RS 0 one (1) BASE UNIT with full duplex VHF radio communications capability 0 seven (7) HEADSET/BOOM MICs BASE UNIT FRONT PANEL FEATURES BENEFITS: FM (Frequency Modulation) Clear, high quality audio communication on main and auxiliary channels. AUX charmel for anew-one communication Private base to mobile communication channel. PBX handset phonejack Private telephone calls to mobile users. Tape Recorder output RCA jack Tape recorded dictation Background music input RCA jack Offers background music as option to ‘pany line". 4 Pin latching/keyed headset connector Push button release with dual connection security for durable connectivity. Base Unit Headset earpiece Volume Control Base unit headset volume adjuster. AUX/OFFICOM switch Switch control between modes in base headset, 8 pin mini DIN outlet Optional dual base unit configurations lN/OUT Phone Audio Controls Base unit phone adjuster. Input Power Coaxial Jack Power supply input Power ON switch REAR PANEL FEATURES BENEFITS 0 Detachable ENC Transmit Antenna Short and easy to manipulate for greater mobility. 0 Detachable BNC Receive Antenna Short, easily manipulated for greater mobility. 0 Output Power High/Low Switch Transmitter output power adjustment Additional product specific comments are included in Operating Use and Tips Page 6. PRODUCT MARKETING CONFIDENTIAL 04/20/99 MOBILE UNIT Front Panel FEATURES BENEFITS 0 Microphone ONIOFF (in/out) switch Audio Out Control at Mobile Unit 0 External 6 Volt Power cable jack Easy battery replacement. 0 4 Pin latching/keyed headset connector Push button release with dual connection security for durable connectivity, 0 Headset/BouliC Crisp, clear delivery of audio/voice communication. 0 Intemal/Extemal Battery Choice of battery configuration. 0 Earphone lateral Clockwise Volume control Easy finger adjustment. Rear Panel FEATURES BENEFIT Detachable BNC Transmit Antenna Short and easy to manipulate for greater mobility. MlCmphone output volume adjuster Voice output control Detachable BNC Receive Antenna Short, easily manipulated for greater mobility. Output Power High/Low Switch Transmitter output power adjustment. GRAPHIC PORTRAYAL OF FUNCTIONAL CONTROL? AND CONNECTIONS MOBILE UNIT — Front Panel Microphone On (in)/0fi‘ (out) Switch A Jack or cable for power in (6V) HEADSET [_ Internal or external battery 4 pin latching headset connector _| LEarphone Volume (increase vol. to right) Additional product specific comments are included in Operating Use and Tips Page 6A PRODUCT MARKETING CONFIDENTIAL MOBILE UNIT — Rear Panel Detachable Transmit Antenna (BNC) 7MIC loudness (clockwise = max.) I | ‘Rcccive Antmna (ENC) MlC LEVEL THANSMH L0 HEEEYVE OUTPUT POWER Two Position Transmitter output Power switch (L0 is V: HI) BASE UNIT — Rear Panel Detachable Transmit Antenna (BNC) Two Position Transmitter output | Power switch (L0 is ‘A HI) | Receive Antenna (BNC) I I mAusmn meczwe OUTPUT POWER HIGH LOW Additional product specific comments are included in Opcrating Use and Tips Page 6. PRODUCT MARKETING CONFIDENTIAL BASE UNIT «Front Panel To second system Local headset — talk to all (COM) Receptacle for | External or talk to selected mobile (AUX) a PBX handset | input Connects selected mobile cord _ | (RCA to external recorder | I jack) l I ., TAPE " mums use x2 as musw necnsurn CUM PHDHE LEVEL 0mm 1 I Loudness adjustment IN (from) and OUT (to) Local earphone volume Input power oo-axial The PBX handset line Jack & Power Switch PHONE — This input is a four wire connection for a separate miuophone and earphone, as are found in most PBX handsets It is not compatible with an ordinary phone line. BASE 82 ~ This is an audio connection to mother Base unit, allowing up to 12 Mobile units to be communicating with each other. The cormector is an 8 pin Mini DIN. BC MUSIC — Audio from an external source (with external level control) is transmitted to all Mobiles and can be monitored by the local headset in the “COM" position. TAPE RECORDER 7 Audio from a selected mobile is routed to this connector (by the switches on top of the Base). The recorder should have a “record level" control, since the Base does not control the amplitude of this signal. POWER lN — The Base requires 9 to 12 Volts DC at .S Amperes. PHONE LEVEL- These controls adjust the incoming and outgoing audio levels for optimum results at both ends of the telephone conversation. The person at the “far" end must be consulted for the best level. Additional product specific comments are included in Operating Use and Tips Page 6. PRODUCT MARKETING CONFlDENTlAL 04/20/99 BASE UNIT — Top Label The switch numbers One through Six (1- 6) correspond to the Mobile unit numbers. TAPE TAPE OUT PHONE BUT PHONE AUX CUM AUX COM 2 3 TAPE TAPE BUT PHONE BUT PHONE AUX CUM AUX CUM 5 B 0 The green LED above each switch, when on , indicates that the signal from the Mobile is being received correctly. 0 When any switch is placed in a position other than “COM“, the corresponding Mobile Unit is automatically switched to a sub-carrier mode of operation, which communicates only through the Base. Other mobiles cannot hear this one-to-one communication, in this sub-carrier mode. SWITCH POSITIONS: COM — Each Base receiver’s audio is fed into the Base transmitter and is therefore retransmitted to all mobile units. This is the “party line" mode of operation. PHONE — The selected Mobile unit is connected to the PBX phone. [ts received signal is connected to the two wires that normally would be the microphone connections of the PBX handset, therefore routing the Mobile Units audio into the ‘phone system. The audio fi'om the ‘phone system is sent to the selected Mobile unit via a subcarrier fi'equency so that only this mobile can hear it. TAPE OUT ——Audio from the selected mobile is connected to the TAPE RECORDER RCA jack rather than being retransmitted. The Base can communicate with the selected mobile that is using the TAPE OUT mode when the base unit local headphone switch is in the AUX position. AUX -The Base can communicate with the selected Mobile when the local headphone switch is in the AUX position. Additional pmdnct specific comments are included in Operating Use and Tips Page 6. PRODUCT MARKETING CONFIDENTIAL 04/20/99 SET UP AND USE BASE UNIT — SET UP STEP ”1 — The detachable (BNC connectors) antennas must not be installed randomly; as they are timed (broadly, over a 10 MHz band) to the transmit and receive frequencies of the mobile unit The markings must be observed when installing — ie. the antenna and panel markings must be identical. Connect the transmit and receive antennas. Note that die markings on the antennas match those on the rear panel. The antennas must, for best results he vertical to the earth. If the Base is wall mounted, the rear panel would be highest. Connect the antennas directly. With the Base on a table top, connect the antennas using a right angle BNC adapter. STEP It: — Plug in the headset, set the volume to approximately halfway, and set the headset selector to COM. STEP #3 — With the power switch to OFF, plug the Base power supply in. Check that all selector switches are in the COM position and turn the power switch to ON. All green LED’s must be OFF (all Mobiles must be OFF). STEP M — Connect all other needed devices to the Base (86 Music, etc.). MOBILE UNIT — SET UP STEP if] - Connect the transmit and receive antennas. Note that the markings on the antennas match those on the rear panel. The antennas must. for best mults be vertical to the earth. The belt and holsters supplied with the system will support a good orientation. STEP $2 — Set the volume to about 1/3 up, and plug the headset in. him the rearpanel MIC. LEVEL to maximum clockwise and set the OUTPUT POWER switch to H1. STEP #3 — Plug the battery in and push the power switch to EXT. The corresponding green LED on the Base should illuminate. Verify operation by talking to another party at the Base, or mb the foam mouthpiece cover on the microphones while listening at the “other end”. Repeat for all Mobile Units. Additional product specific comments are included in Operating Use and Tips Page 6. PRODUCT MARKETING CONFIDENTIAL 04/20/99 USE & OPERATING HINTS Although these controls/connections are simple and fairly obvious, some elaboration is useful: ANTENNAS — The antennas supplied for the Base will suffice for most applications. In order to keep from being in the way, the antennas for the Mobile Unit are intentionally short. Other antennas (for longer transmit/receive distances) are available. If the Base needs to be at one end of an area (containing the operating Mobile Units), directional antennas can he used on the Base. They will provide a significant increase in efliciency. For best range, keep the antennas away from conductive surliaces (metal walls, the human body, etc). BATTERIES —The supplied batteries are lead acid (gelcell). They have no “memory “ effects, so should be recharged alter use, even if the time of use is short (over 30 minutes). Lead acid batteries should never be lcfi in a discharged state. They should be recharged every 3 to 4 months while in storage. The Mobile Unit has a low battery detector that generates clicks in the earphone. When this occurs, replace the battery within 10 to 15 minutes The battery charger supplied with the system provides an optimum charging profile including an automatic “float charging mode" when the battery is fully charged. The battery can be lefl on the charger indefinitely LOW SETTINGS" Set the Output Power to LOW when all the mobile units are close to the Base unit, and are close to each other to reduce unit to unit interference. MIC'S l: EARPHONES — To reduce system noise the MIC should be OFF if a user does not plan to talk. The sound level startup can be very loud. Reduce the volume before applying power. The MIC level should he reduced for users with unusually loud voices. The microphones are noise—cancelling electrets which need an excitation voltage (supplied by the system). Substitute microphones may not operate properly. For best results, place the MIC approximately one thumb’s thickness away from and to the side of the mouth. The user should speak firmly and clearly. The earphones are 32 ohm dynamic elements in an open air configuration (the ear is not enclosed). The user can hear mom sounds and background noise from the same ear used for the system. The car phone should firmly contact the ear. MJSCELLANEOUS — The entire system uses a squelch lone scheme, wherein the transmitter emits a fixed frequency tone as well as the normal audio. The corresponding mciver has a circuit, which detects the tone and allows normal operation. At long range the tone becomes noisy and the detector loses it, at which point the detector shuts off (squelches) the received audio (noisy or not). The green LED’s on the Base are driven by the tone detector in each receiver. They are ON when the Mobile Unit is detected. A FCC SITE LICENSE may be required to operate this unit. TROUBLESHOOTING The COMMdroIcc2000 7” Communication System was designed for stability over time and temperature. It uses surface mount construction for light weight ruggedness. There are no user replaceable or adjustable components inside the housings. The batteries will degrade in capacity over time and with recharge cycles. One to two years real time use should be expected. For Customer Service: Call your Sales Representative or [I 800 M-DEVICES] Manufacturer: Bio-Medical Devices, Inc. 320 Kaimus Drive Costa Mesa, CA 92626 Additional product specific comments are included in Operating Use and Tips Page 6.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2001:06:25 14:03:10 Producer : Acrobat Distiller 4.0 for Windows Author : VicodinES /CB /TNN Title : 38610.pdf Modify Date : 2001:06:25 14:03:19-04:00 Page Count : 8EXIF Metadata provided by EXIF.tools